1400 Bridge Problem

I am installing a point to point bridge link using 1400 briges w/power injectors. The bridges are installed but the link goes up and down about every few minutes. When it does connect, it starts out at a low dbm but eventually ends up in the 80's and then loses connection again. We installed a couple of other briges in another location and didn't have any problems at all. I know the distance between sites is way withing specs and there is nothing that could block this link. Any ideas as to what could be causing this. Thanks...

Well, there can be many reasons why this happening. First there could be some issue with the configuration specifically authentication parameters, WEP keys, role of bridge configuration and so on. If you are sure sure that the configuration on both ends of the Bridge are perfect, and if the connectivity between the bridges is intermittent the problem may be RF interference, CRC errors and so on. For more information on this read the document available at the following URL.
http://www.cisco.com/en/US/products/hw/wireless/ps5279/products_tech_note09186a0080508551.shtml

Similar Messages

When i open pc an adobe bridge problem denotes purging

when i open computer an adobe bridge problem denotes purging

Are you trying to say that pointing to your computer in Bridge you get an error message telling you that you need to purge the central Cache?
If so, go ahead and purge it.
Your post is not clear at all. Try rephrasing it, please.
Also:
A lot more information about your hardware and software is needed.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CC", but something like CC2014.v.2.2) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
a screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

CS6 Bridge and Mini Bridge problems

Installed CS6 and clicked on Brose in Bridge. I get the rror messare could not complete the Brose in Bridge commmand because Photoshop was unable to find the Java Script plugin. Also when clicking on Brose in Mini Bridge I get the message cannot complete the command because the extension could not be loaded I have uninstalled CS6 and reinstalled it and get the samew message Help please

Thank you very much I will try that
In a message dated 11/24/2014 12:41:45 P.M. Central Standard Time,
[email protected] writes:
CS6 Bridge and Mini Bridge problems
created by Flashy1995_ (https://forums.adobe.com/people/Flashy_1995) in
Photoshop General Discussion - View the full discussion
(https://forums.adobe.com/message/6958475#6958475)

Answers to common Bridge problems.

Here are user-submitted answers to common Bridge problems.
I invite all suggestions to addition/corrections/improvements.

Bumped. I'll convert to document once it will be possible to do so. I have great addendum by CurtY:
Windows and Mac FAQ and Translation Key
Keystrokes
ALT on a Pc = Option on a Mac (On some keyboards (UK), the Option key is labeled with Alt. )
CTRL (Control) on Pc = Cmd (Command) on a Mac, the key has the following symbol: ⌘
Right-click on a Pc = Right-click on a Mac, or Control+Click on machines without a mouse.
Menu differences
Preferences (CMD+K) are found on the Photoshop menu on a Mac, at the bottom of the Edit menu on a PC, and the shortcut is (CTRL+K).
On the same Photoshop menu on a Mac, one can find About Plug-ins... and About Photoshop, while they are located on the Help menu on a PC.
Quit Photoshop (CMD+Q) is also on that Photoshop menu on a Mac, while Exit (CTRL+Q) can be found at the end of the File menu on a PC.
Preferences location on the hard drive. There is a full document on that topic: http://kb2.adobe.com/cps/828/cpsid_82893.html
but basically: The main preference file, is on both plaform Adobe Photoshop CSx Prefs.psp it is located, alongside most other preferences on:
Mac location: Users/[user name]/Library/Preferences/Adobe Photoshop CSx Settings
Windows XP: Documents and Settings/[user name]/Application Data/Adobe/Adobe Photoshop CSx/Adobe Photoshop CSx Settings
Windows 7 and Vista: Users/[user name]/AppData/Roaming/Adobe/Adobe Photoshop CS5/Adobe Photoshop CSx
Settings Keywords
pc = C:/Users/user name/AppData/Roaming/Adobe/BridgeCSx/ (note: to view AppData turn on hidden file option)
Mac = (your computer name)/ Library / App Support / Adobe / Bridge CSx / Adobe
Camera Raw location NOTE: Should be only one file here.
PC = Program Files/COMMON Files/Adobe/Plug-ins/CSx/File Formats which gives you Camera Raw.8bi
Mac = /Library/Application Support/Adobe/Plug-ins/CSx/File Formats/
Photoshop Actions
Mac - Actions (not saved) Actions panel.psp Users/[user name]/Library/Preferences/Adobe Photoshop CSx Settings
Mac - Actions (saved) Actions panel.atn Program Files/Adobe Photoshop CSx(64bit)/presets/actions
PC - Actions (not saved) Actions panel.psp Users/[user name]/AppData/Roaming/Adobe/Adobe Photoshop CS5/Adobe Photoshop CS5 Settings
PC - Actions (saved) Actions panel.atn Program Files/Adobe Photoshop CSx(64bit)/presets/actions

Beans - Active-x Bridge - Problems!

Hi,
I developed an ip address bean based on JTextField (JDK 1.3.1_02), successfully packaged it as an active-x control using the packager and instructions in the active-x bridge tutorial.
The control has all sorts of problems under visual basic: to name a few:
1. The caret seems to disappear when the control receives focus
2. The tooltips dont seem to show up.
3. The focus lost event does not seem to fire in the control.
Is it worth for me to trace these issues or is the activex bridge not really practically used by anybody ?
Thanks in advance,
Vishy

Vishy,
Did you by any change find a solution to your ActiveX Bridge problem, I'm stuck with the same shit..
Thanks,
Harvey
P.S. Maybe nobody works with this technology except maybe none-visual components?

Virtualbox bridging problem

I post this a second time, this time more precisely
Op. System is: Archlinux 64bits
uname -a:
Linux archie 2.6.31-ARCH #1 SMP PREEMPT Tue Nov 10 19:01:40 CET 2009 x86_64 Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz GenuineIntel GNU/Linux
so
I've installed virtualbox_bin 3.1.0-1 from AUR (the only way possible on a 64 bits opsys, besides the install stuff from Sun)
Followed the installation given on the Arch Wiki
I've tried all three methods ( vbox way, arch way, general ) to get bridged networking to work
( I'm a lazy guy, I prefer the Vbox way, all my modules are loaded)
All my VMs are running fine with NAT, everything works,
but bridging produces a strange error:
Clients get network adresses via DHCP,
even fixed IP settings work,
I can ping ABSOLUTELY ANYTHING
but no internet connection!
I have observed the (physical) network card with Iptraf of the HOST machine, the result is strange:
ICMP packets go through but no TCP/IP communication is possible between my hosts and the exterior world
AH, I forgot the most interesting one, I've an archlinux VM too, HE IS WORKING FINE, EVEN IN BRIDGED MODE!!!!
Is that a bridging problem?
Is that a kernel problem? ( Vbox worked well with the latest kernel - 2.6,30 -, if I remember well...)
What the hell is going on there?
( I really need bridged network, as I use Vbox essentially for network testing purposes)
Please, help!

After three weeks of research I have found lots of people having trouble with Virtualbox bridged and host-only networks
the (partial ) solution is to change the virtual network card, for me Intel Desktop M worked fine with my Debian guest
but Ubuntu doesn't want to do anything with it
for some people it works, for others it forks for a while, for others it doesn't work at all...
Buggy stuff

1400 Bridge Constantly Restarting

I have a Cisco 1400 Bridge that suddenly lost connectivity the other day. It appears that the bridge is constantly rebooting once it hits a certain point. After about 60 seconds, the status lights all turn orange and another 20 seconds later the device makes a clicking noise, and the boot sequence starts all over again. I cannot access the bridge from http or telnet so I don't know what is happening in the boot process. Any suggestions or ideas?
Thanks,
Shaun

Sounds like you have bad injector unit or bad bridge.
Seth Rosenthal CWNE #55

1400 bridge and VLANs

I have two sites bridged with 1400 bridges.
I wish to bridge a single vlan between the two sites. However I want to setup the bridges with management IP's on seperate subnets (the local management subnet for each site).
The only way I can get this to work without bridging various vlans together is to not use the BVI1 interface and apply the bridge management ip to a subinterface as per below:
interface FastEthernet0.816
encapsulation dot1Q 816
ip address 10.97.16.100 255.255.255.0
no ip route-cache
bridge-group 2
bridge-group 2 spanning-disabled
interface BVI1
no ip address
no ip route-cache
Then not bridge this vlan816 on the radio interface.
The issue with this is that the snmp process on these bridges seems to be hard coded to bind only to BVI1 - hence snmp does not work at all. I have a TAC case in re the snmp which is obviously a bug. However I was wondering if anyone else has met these similar requrements via another means?
Thanks for any help.
Kent.

Hi.
You only way, you can access to the bridge using IP (snmp or other protocols)is configuring BVI1 with ip, in the VLAN what ever you want or chose for management and the same ip range an vlan for the other bridge and BVI1 too, because the APs o bridge only can bridge IP over this BVI1.
Regards.

1400 Bridge coax connection question

I have two AIR-BR1410A-A-K9 bridges that I need to use for connecting a vehicle to a building network. The bridge on the building will use the conventional mount and network connection. The other bridge is going on top of a vehicle (bigger than a UPS truck, smaller than an 18-wheeler). There are several existing coax runs from the interior of the vehicle to the roof of the vehicle. All runs terminate with an N connector inside and an NMO outside and are 50 ohms. I would like to use these runs for the Bridge, but the F-connectors/cables for the 1400 are 75 ohms.
Specifically, I want to put the injector inside the vehicle and use the existing vehicle coax runs and mount the bridge on the roof of the vehicle. I have found the F-to-N and F-to-NMO adapters. What kind of trouble am I going to run in to running the Ethernet and power over cables/connectors with mismatched impedance? I'll try to step through the entire run:
Ethernet 100Base-T and DC Power connects to the injector
F-type coax (75 ohm) cables from injector run 4 feet to connect to F-to-N adapter (not sure what the impedance is here)
F-to-N adapter connects to N connector at coax patch panel inside vehicle (50 ohm at panel connector)
Patch panel coax travels approximately 40 feet to roof-mounted NMO connector (50 ohm)
NMO-to-F coax adapter connects to NMO (not sure of the impedance here)
F-coax runs 10 feet to Bridge (75 ohm)
Will this work, or do I need to build a couple of transmatch stubs (I assume I would need one at each end)?
I have a good RF guy working with me on this project, but we are stumped since the coax carries the ethernet and power, not "normal" RF signals.

Should be no problem.
There will be some additional loss on the radio signal, there will possibly be a small amount of stress on the transcievers, but nothing it can't handle.
As for the power; it's DC, so there is no "impedance" to the conductors, just plain'ol' DC resistance ... which will be virtually identical between the two type of cables (50 and 75 ohm coax).
Good Luck

Adobe Bridge problem

To whom this question may be directed to:
Please gidet me in resolving my problem with TRYING to open a file in Adobe bridge CC only to be presented a message telling me that it can NOT be opened because CS 5 is no longer on my computer of which I already know. Although if I go into explorer I can double click it and it opens into Photoshop CC fine.
ANYONE with an soultion to this problem and is WILLING to share the information I would be EXTREMLEY appreciateive.
Thank You in advance for taking the time to reply
Regards
Bill

Curt,
Once again thank you for being paitent with me in trying to resolve thsi problem, I am having a bit of confusion with trying tounderstand just what ext you are refeerring to.
I go to preferences and see all the exttions BUT do not understand which one I need to select and when I do select it do I then go to reset all defauls option?
I apoligize for seeming ignorant in this discussion but i am not grasping this procedure correctly I assume.
Thanks again for your assistance
Bill

S/A bridge problem: No object type found for the message

Hi all,
I've been spending days looking into the following problem. I have a RFCXIFile scenario. The R3 system sends data via an RFC to XI and XI post the data as a flat file on a certain server using FTP.
This scenario worked just fine for 1 exception. I could only run this scenario once. The second time I got timeouts when checking the data sent to my RFC destination using SM58. When I reactivated my RFC communcation channel I could again send 1 RFC to the system. All subsequent tries would fail.
I guess this is due to the fact that I use a synchonous call (RFC) to an asynchronous one. Thus the adapter is still waiting for the response from the XI system and will not accept any further new calls from R3.
So I figure let's use this pattern called the S/A bridge. So I designed everything according to guides and examples and I'm quite certain everything is configured right but when I run the scenario I get the following message:
<i> 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIAdapter</SAP:Category>
<SAP:Code area="BPE_ADAPTER">UNKNOWN_MESSAGE</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>No object type found for the message. Check that the corresponding process is activated</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error></i>
It seems that the adapter cannot find any integration process to send the message into!?
I've looked at numerous threads on sdn and tried all kinds of stuff (looked at the cache==> code 0 = OK , tried to reactivate my integration process, checked the interface determination,...), but to no avail. Does anybody has an idea what could be wrong ?
Any help would be greatly appreciated for I'm all out of clues....
Bob

First of all, Thank you for trying to help me out here.
Some answer to your suggestions/questions:
The IP has return code 0 in SXI_CACHE. so that doesn't seem to be the problem.
I've checked the BPM for syntax errors. I doesn't have any.
I've reimported the BPM into the integration directory.
And did a full cache refresh in SXI_CACHE. Return code is (stays) zero, so that's OK.
I've already included the error message from SXI_MONI. It is in the last step ("Call Adater") that the error occurs.
The other steps execute just fine...
The RFC communcation channel accepts the incoming RFC call and puts into the pipeline, so no problems with the communication channel either. the problem is actually when the pipeline is trying to forward the message into an IP trhough the BPE_ADAPTER (according to SXMB_MONI).
Therefore I'm not able to go to into PE, because the workflow is never started. the BPE_ADAPTER does not find any active process for the interface determination i've entered.
So i can not debug the IP in the PE and check container variables, like some of you mentioned.
Maybe some more information about the scenario:
The RFC is called from an R3 system to XI over the interface "CONTROL_RECIPE_DOWNLOAD", which is an imported RFC, with a request and response message type.
Then I got a receiver and interface determination with lead the incoming RFC message to the IP, into interface "XI_ERP_MF_MD_CONTROL_RECIPE_REQ_AI_MI".
This is an abstract synchronous interface based on the request and response types of the "CONTROL_RECIPE_DOWNLOAD" imported RFC.
This interface is used the first step (receive) of my BPM as the synchronous interface to open the S/A bridge.
The message (container var) used in this step is
name: CORREQ
Category: Abstract interface
type: "XI_ERP_MF_MD_CONTROL_RECIPE_REQ_AI_MI"
The interface "XI_ERP_MF_MD_CONTROL_RECIPE_REQ_AI_MI" is an abstract, asynchronous interface based on the request type of the "CONTROL_RECIPE_DOWNLOAD".
Then there are 2 send steps for putting the flat files into place and finally i close the the S/A bridge using message:
name: CORRES
Category: Abstract interface
type: "XI_ERP_MF_MD_CONTROL_RECIPE_RES_AI_MI"
The interface "XI_ERP_MF_MD_CONTROL_RECIPE_RES_AI_MI" is an abstract, asynchronous interface based on the response type of the "CONTROL_RECIPE_DOWNLOAD".
I hope this information gives you guys a better understanding of hte problem.
Really looking forward to see more suggestions and to solve this nasty problem ...
Regards,
Bob

BPM - Receive Sync/ASync Bridge Problem

Hi,
I am creating a scenario for an inbound Synch request to be serviced by a BPM process.
Here is the problem that I am facing while trying to configure the Receive Step
- I created a Message Interface defined as Abstract Synchronous.
- I created a process model and put in a Receive Step: Mode - Opens S/A Bridge, Synchronous Interface - defined as above.
- I define a container with Abstract type. But when I try to locate the above defined Abstract Synch message interface, I cannot find it.
- As a workaround, I create another Abstract Message Interface defined as Abstract ASynch.
- I create a container with this Abstract ASynch message type.
- I use this container in the Receive Step.
But activating the Business Process gives the error:
Message to be received and Synchronous Interface do not have identical types.
Can someone give me the correct procedure to configure the Sync / ASync Bridge ? thanks,
-Manish

Dan,
This is the link you are looking for?
http://help.sap.com/saphelp_nw04/helpdata/en/83/d2a84028c9e469e10000000a1550b0/frameset.htm

CS5 Design Premium Installation Adobe Bridge problem

When I try and install CS5 Design Premium it fails because it wants me to close Adobe Bridge (which is not open) and won't let me go any further. I tried uninstalling CS3 but it won't let me because it wants me to close Adobe Bridge.
What Now?

There shoult be a Bridge icon in the system tray (bottom right corner), close Bridge from here and run the uninstaller or if you don't find this icon you can kill process Bridge.exe but this is not always the best way to overcome a problem. I would recommend closing the application from system tray icon.
Thanks,
Tahseen

Photoshop Bridge problem

Bridge opens to Paint or Windows explorer on the first try when opening a photo. Subsequently pictures open to CS4 as they should.Bridge opened to Windows Explorer after Paint disabled. CS3 similarly affected after CS4 installed and CS2 removed.Problem persists.

This is the boilerplate text I use in connection to saving to a network (please NOTE the part where it explains that normally, it does work, but that it is impossible to troubleshoot someone else's network remotely, and that's why it's not supported by Adobe):
If you are opening files over a network or saving them to a network server, please cease and desist immediately in the event you are currently experiencing problems with one or more files. Working across a network is not supported.
See:
http://www.adobe.com/support/techdocs/322391.html
Copy the CLOSED file from your server to your local hard disk, work on it, save it again to your local hard disk, close it, and copy the closed file back to the server.
Of course, the fact that Adobe does not support working across a network does not necessarily mean it won't work. It should.
Adobe's position is that there are too many variables in a network environment for them to guarantee that everything will work correctly in every network, especially given the fact that if something does not work properly, it's probably the network's fault, and Adobe has no way of troubleshooting your network.
If you can't work locally, you are on your own, and if something happens, you're on your own. If you must work from a server, make sure your network administrator is a competent professional.
When problems arise, a lot of valuable work can be lost.

Bridge Problem opening files in Photoshop CS6

CS6 Bridge appears to work fine, however when I try to open a file into Photoshop CS6 I get a flag saying it cannot find Photoshop CS4? Any ideas?
TIA Keith

PhotoGene47 wrote:
You can open Bridge and change the file associations in Edit>File Type Associations to change to PS CS6. That is the easiest way. Another way would be to open Control Panel>Programs>Default Programs to change the file association for .jpeg, .psd., .tif, et cetera.
For your info, and others, this does not work in situations were the file associations become corrupted by uninstalling a previous version. The mechanism for corruption is not quite clear to Adobe, but somehow the registry for file associations gets reset to the version that was deleted. Since the normal methods of changing file associations, that you mention, do not affect the registry file in question, the problem still remains. Therefore one needs to wipe files with the Adobe Script Cleaner or go in and change the registry.

1400 Bridge Problem

Similar Messages

Maybe you are looking for