144 cycles with only 6% health, is that normal?

Hi there!
I´m writing you from Spain cause it seems than the Spanish Apple support service is unable to do or to tell me anything else about my battery. As I wrote on the subject my battery is just with a 6% of health after only 144cycles. The weird thing is that in spite of the fact that the battery is doing more cycles now, the cycle counter doesn´t change at all! Is that normal?
Do you think I can get another new battery without any charge? My MBP is from March 2007 but it seems not to be under the exchange battery program.
Thanks a lot!

Have you calibrated your battery?
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh2339.html
After doing this, do a PRAM reset:
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Then, lastly, an SMC reset:
If the computer is on, turn it off.
Disconnect the AC Adapter and remove the computer's battery.
Press and hold the power button for 5 seconds and then release the button.
Reconnect the battery and AC Adapter.
Press the power button to restart the computer
This should hopefully reset the callibration, and your battery should get better. It's possibly not the battery that's at fault, but how the mac reads the information on the battery

Similar Messages

  • 1 week MBP - 7 cycles and only 94% health !!!!!

    I've received my MBP last Monday (18th January 2010), I've now 7 cycles completed and Istat Pro says that my battery's health is only 94%!!!
    This shouldn't happen this far, am I right??
    Since day 2 or 3 it has been decreasing... I intend to calibrate it today, but nevertheless don't think this is normal. I've been using it normally. Any advice/suggestion?
    Thanks!

    Here's what it says in system profiler:
    Charge Information:
    Charge remaining (mAh): 5126
    Fully charged: No
    Charging: Yes
    Full charge capacity (mAh): 6153
    Health Information:
    Cycle count: 8
    Condition: Normal
    Battery Installed: Yes
    Amperage (mA): 1725
    Voltage (mV): 12530
    According to: http://discussions.apple.com/thread.jspa?threadID=1764220
    My battery's health (doing the maths) is now only 92,3% (6153/6665)*100
    Even lower than Istat predicts!

  • I cant sync songs on a new computer because it'll replace my ipod with only the songs on that itunes

    Every time I try to sync my music, it says itunes will replace ipod contents with contents from itunes library but i have alot of songs on there so I don't want to lose them.  I do have a new computer but my old one is dead so I can't do that "home sharing" thing

    - Transfer iTunes purchases to yur new computer by:
    iTunes Store: Transferring purchases from your iPhone, iPad, or iPod to a computer
    - Transfer other stuff by using the information provided in this previous discusion:
    Best iPod to PC
    - They let iTunes erase your iPod and replace its contents with what is now in your itunes library.

  • 2 Problems. 1. Black Screen With Only Cursor Showing 2. Explorer.exe blocked.

    Hello Guys and Gals,
    I am having a problem with my Laptop.  First of all, my screen is black with only a cursor showing (that is not blinking) and I can only run programs through Task Manager. Second, I cannot open 'explorer.exe'.  When
    I try I get this error: "This app can't run on your PC. To find a PC version, check with the software publisher".  I really would like help with this as I do not wish to spend another $500 on the same laptop. Also due to the fact that I have
    many important files I do not wish to loose.  
    INFORMATION:  
    I have an Acer running Windows 8 (It came with it).
      6GB DDR3 Memory
    Thank you for your time. Cheers!
     -Gamerboy1337

    Hi,
    I notice the issues are related to Windows 8. I suggest you post in Windows 8 forum to get professional support.
    http://social.technet.microsoft.com/Forums/windows/en-US/home?category=w8itpro
    Niki Han
    TechNet Community Support

  • 2 Problems. 1. Black Screen With Only Cursor Showing 2. Explorer.exe blocked. [Re-Ask]

    Hello Guys and Gals,
    I am having a problem with my Laptop.  First of all, my screen is black with only a cursor showing (that is not blinking) and I can only run programs through Task Manager. Second, I cannot open 'explorer.exe'.  When I try I get this error: "This
    app can't run on your PC. To find a PC version, check with the software publisher".  I really would like help with this as I do not wish to spend another $500 on the same laptop. Also due to the fact that I have many important files I do not wish
    to loose.  
    INFORMATION:
    I have an Acer running Windows 8 (It came with it).
    6GB DDR3 Memory
    Thank you for your time. Cheers!
     -Gamerboy1337

    Added "fl *" 
    Response:
    PSPath            : Microsoft.PowerShell.Core\FileSystem::C:\WINDOWS\explorer.exe
    PSParentPath      : Microsoft.PowerShell.Core\FileSystem::C:\WINDOWS
    PSChildName       : explorer.exe
    PSDrive           : C
    PSProvider        : Microsoft.PowerShell.Core\FileSystem
    PSIsContainer     : False
    VersionInfo       : File:             C:\WINDOWS\explorer.exe
                        InternalName:     explorer
                        OriginalFilename: EXPLORER.EXE.MUI
                        FileVersion:      6.3.9600.16384 (winblue_rtm.130821-1623)
                        FileDescription:  Windows Explorer
                        Product:          Microsoft® Windows® Operating System
                        ProductVersion:   6.3.9600.16384
                        Debug:            False
                        Patched:          False
                        PreRelease:       False
                        PrivateBuild:     False
                        SpecialBuild:     False
                        Language:         English (United States)
    BaseName          : explorer
    Mode              : -a---
    Name              : explorer.exe
    Length            : 2280232
    DirectoryName     : C:\WINDOWS
    Directory         : C:\WINDOWS
    IsReadOnly        : False
    Exists            : True
    FullName          : C:\WINDOWS\explorer.exe
    Extension         : .exe
    CreationTime      : 2014-02-10 3:28:22 PM
    CreationTimeUtc   : 2014-02-10 8:28:22 PM
    LastAccessTime    : 2014-02-10 3:28:22 PM
    LastAccessTimeUtc : 2014-02-10 8:28:22 PM
    LastWriteTime     : 2013-11-13 2:31:11 PM
    LastWriteTimeUtc  : 2013-11-13 7:31:11 PM
    Attributes        : Archive

  • Issue with only one client - The client version 5.00.7958.1000 does not match the MP version 5.00.7711.0000. The client will not be installed.

    Below issue is with only one client in that untrusted domain. So boundary is not the issue.
    Env -
    mydom.com has SCCM PRI site (MP, DP as well).
    Client is in untrusted forest.
    Please help.
    Thanks
    MP 'mysccm.mydom.com' is compatible ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Retrieved 1 MP records from AD for site 'pri' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Retrived site version '5.00.7958.1000' from AD for site 'pri' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    SiteCode:         pri ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    SiteVersion:      5.00.7958.1000 ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Ccmsetup is being restarted due to an administrative action. Installation files will be reset and downloaded again. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Deleted file C:\Windows\ccmsetup\client.msi ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Only one MP mysccm.mydom.com is specified. Use it. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Searching for DP locations from MP(s)... ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Current AD site of machine is Default-First-Site-Name LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Local Machine is joined to an AD domain LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Current AD forest name is staging.local, domain name is staging.local LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    DhcpGetOriginalSubnetMask entry point is supported. LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Begin checking Alternate Network Configuration LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Finished checking Alternate Network Configuration LocationServices 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Sending message body '<ContentLocationRequest SchemaVersion="1.00">
      <AssignedSite SiteCode="pri"/>
      <ClientPackage/>
      <ClientLocationInfo LocationType="SMSPACKAGE" DistributeOnDemand="0" UseProtected="0" AllowCaching="0" BranchDPFlags="0" AllowHTTP="1" AllowSMB="0" AllowMulticast="0"
    UseInternetDP="0">
        <ADSite Name="Default-First-Site-Name"/>
        <Forest Name="staging.local"/>
        <Domain Name="staging.local"/>
        <IPAddresses>
    <IPAddress SubnetAddress="10.72.117.0" Address="10.72.117.134"/>
    <IPAddress SubnetAddress="10.72.117.0" Address="10.72.117.142"/>
        </IPAddresses>
      </ClientLocationInfo>
    </ContentLocationRequest>
    ' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Sending message header '<Msg SchemaVersion="1.1"><ID>{5B972249-B931-4739-9EFA-A9FDE29C351A}</ID><SourceHost>STAGINGSRVR07</SourceHost><TargetAddress>mp:[http]MP_LocationManager</TargetAddress><ReplyTo>direct:STAGINGSRVR07:LS_ReplyLocations</ReplyTo><Priority>3</Priority><Timeout>600</Timeout><ReqVersion>5931</ReqVersion><TargetHost>mysccm.mydom.com</TargetHost><TargetEndpoint>MP_LocationManager</TargetEndpoint><ReplyMode>Sync</ReplyMode><Protocol>http</Protocol><SentTime>2014-11-04T17:14:55Z</SentTime><Body
    Type="ByteRange" Offset="0" Length="1264"/><Hooks><Hook3 Name="zlib-compress"/></Hooks><Payload Type="inline"/></Msg>' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    CCM_POST 'HTTP://mysccm.mydom.com/ccm_system/request' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Content boundary is '--aAbBcCdDv1234567890VxXyYzZ' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Received header '<Msg SchemaVersion="1.1">
     <ID>{D4EF0A4D-A000-4697-9AFA-B1317B09931D}</ID>
     <SourceID>GUID:21298681-5080-4365-B614-F0C8DF67452B</SourceID>
     <SourceHost>pri1SCCM02</SourceHost>
     <TargetAddress>direct:STAGINGSRVR07:LS_ReplyLocations</TargetAddress>
     <ReplyTo>MP_LocationManager</ReplyTo>
     <CorrelationID>{00000000-0000-0000-0000-000000000000}</CorrelationID>
     <Priority>3</Priority>
     <Timeout>600</Timeout>
     <TargetHost>STAGINGSRVR07</TargetHost><TargetEndpoint>LS_ReplyLocations</TargetEndpoint><ReplyMode>Sync</ReplyMode><Protocol>http</Protocol><SentTime>2014-11-04T17:14:55Z</SentTime><Body Type="ByteRange"
    Offset="0" Length="2408"/><Hooks><Hook3 Name="zlib-compress"/><Hook Name="authenticate"><Property Name="Signature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roperty><Property
    Name="AuthSenderMachine">pri1SCCM02;mysccm.mydom.com;</Property><Property Name="MPSiteCode">pri</Property></Hook></Hooks><Payload Type="inline"/></Msg>' ccmsetup 11/4/2014 12:14:55
    PM 4816 (0x12D0)
    Received reply body '<ContentLocationReply SchemaVersion="1.00"><ContentInfo PackageFlags="16777216"><ContentHashValues/></ContentInfo><Sites><Site><MPSite SiteCode="pri" MasterSiteCode="pri"
    SiteLocality="LOCAL" IISPreferedPort="80" IISSSLPreferedPort="443"/><LocationRecords><LocationRecord><URL Name="http://mysccm.mydom.com/SMS_DP_SMSPKG$/pri00002"
    Signature="<ADSite">http://mysccm.mydom.com/SMS_DP_SMSSIG$/pri00002"/><ADSite Name="CSSG-Mount-Laurel"/><IPSubnets><IPSubnet Address="10.72.117.0"/><IPSubnet
    Address=""/></IPSubnets><Metric Value=""/><Version>7958</Version><Capabilities SchemaVersion="1.0"><Property Name="SSLState" Value="0"/></Capabilities><ServerRemoteName>mysccm.mydom.com</ServerRemoteName><DPType>SERVER</DPType><Windows
    Trust="0"/><Locality>LOCAL</Locality></LocationRecord></LocationRecords></Site></Sites><ClientPackage FullPackageID="pri00002" FullPackageVersion="2" FullPackageHash="03CFD97C8FB5F7E7E9F177FD6D30D6F25ED106E517E69B715695A0E81DB1D9AF"
    MinimumClientVersion="5.00.7958.1000" RandomizeMaxDays="7" ProgramEnabled="false" LastModifiedTime="30388855;1262113920" SiteVersionMatch="true" SiteVersion="5.00.7958.1000" EnablePeerCache="true"/><RelatedContentIDs/></ContentLocationReply>'
    ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Found local location 'http://mysccm.mydom.com/SMS_DP_SMSPKG$/pri00002' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Discovered 1 local DP locations. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    PROPFIND 'http://mysccm.mydom.com/SMS_DP_SMSPKG$/pri00002' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Got 401 challenge Retrying with Windows Auth... ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    PROPFIND 'http://mysccm.mydom.com/SMS_DP_SMSPKG$/pri00002' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Failed to correctly receive a WEBDAV HTTP request.. (StatusCode at WinHttpQueryHeaders: 401) ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Failed to check url http://mysccm.mydom.com/SMS_DP_SMSPKG$/pri00002. Error 0x80004005 ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Enumerated all 1 local DP locations but none of them is good. Fallback to MP. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    GET 'HTTP://mysccm.mydom.com/CCM_Client/ccmsetup.cab' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    C:\Windows\ccmsetup\ccmsetup.cab is Microsoft trusted. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Successfully extracted manifest file C:\Windows\ccmsetup\ccmsetup.xml from file C:\Windows\ccmsetup\ccmsetup.cab. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Loading manifest file: C:\Windows\ccmsetup\ccmsetup.xml ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Successfully loaded ccmsetup manifest file. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Checking if manifest version '5.00.7958.1000' is newer than the ccmsetup version '5.0.7958.1000' ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Running from temp downloaded folder or manifest is not newer than ccmsetup. ccmsetup 11/4/2014 12:14:55 PM 4816 (0x12D0)
    Adding file 'HTTP://mysccm.mydom.com:80/CCM_Client/x64/client.msi' to BITS job, saving as 'C:\Windows\ccmsetup\client.msi'. ccmsetup 11/4/2014 12:14:56 PM 4816 (0x12D0)
    Starting BITS download for client deployment files. ccmsetup 11/4/2014 12:14:56 PM 4816 (0x12D0)
    Successfully completed BITS download for client deployment files. ccmsetup 11/4/2014 12:14:57 PM 4816 (0x12D0)
    Successfully downloaded client files via BITS. ccmsetup 11/4/2014 12:14:57 PM 4816 (0x12D0)
    Validated file 'C:\Windows\ccmsetup\client.msi' hash 'A5732CE24F2B1545E9FBA458971E0A5504093E0F743CA9E8BD9C047582902878' ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    Retrieved client version '5.00.7958.1000' and minimum assignable site version '5.00.7845.1000' from client package ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    Checking compatibility of site version '5.00.7958.1000', expect newer than '5.00.7845.1000' ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    Site version '5.00.7958.1000' is compatible. Client deployment will continue. ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    An MP exists on this machine. ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    The client version 5.00.7958.1000 does not match the MP version 5.00.7711.0000.  The client will not be installed. ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    A Fallback Status Point has not been specified.  Message with STATEID='318' will not be sent. ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    InstallFromManifest failed 0x80004005 ccmsetup 11/4/2014 12:14:58 PM 4816 (0x12D0)
    CcmSetup failed with error code 0x80004005 ccmsetup 11/4/2014 12:14:58 PM 3680 (0x0E60)

    Why two primary that is 'coz geographically based server support and workstation. You can think it as a data center to data center split.
    That doesn't make sense and aren't valid reasons for 2012 (not that you can necessarily change it now).
    This line jumps out at me in the log file though: "An MP exists on this machine".
    That looks like the system you are installing on previously had an MP on it. I would delete the ccm namespace in WMI, cleanup all reference to ccm and Configuratin Manager from the registry, and then try again.
    Jason | http://blog.configmgrftw.com | @jasonsandys

  • The battery in my MacBook Pro 17 requesting assistance only after 277 cycles with a capacity of 9444 mAh

    the battery in my MacBook Pro 17 requesting assistance only after 277 cycles with a capacity of 9444 mAh, Is it possible?I performed the calibration, but nothing changes.
    MacBook Pro (17 pollici, Half 2010)
    MacBookPro6,1
    Intel Core i5
    2,53 GHz
    Memory 4 GB

    Batteries will vary in how long they last. Apple will say that for machines built in the last 4 years that the battery may last up to 5 years approximately. However this depends on usage.
    You can have someone who never ever uses the battery and only ever runs the computer from the mains and the battery will fail as it never gets used and the cycle count will be very low.
    To put things in perspective. I have a 15" Macbook Pro with Retina Display (Late 2013). I've had it for probably 8 months and I have 128 cycles on my battery, approx. half yours in a quarter of the time. So if you're not always use the battery it can be affected in other ways.
    You can try to see if calibrating the battery helps. Look at http://apple.com/batteries for information on how to do this or try an SMC Reset and see if these make a difference. If not, then seek support from an Apple Store or Authorised service provider.
    Hope this makes sense.
    -Dib.

  • Acmcneill1ug 14, 2014 7:16 AM I have IMac OSX 10.9.4, 4GB,Processor 3.06 with Intell2Duo. I would like to check for Malware. I run a TechTool Pro 6 every month and that comes up great. When check how much memory I am using, with only Safar

    Acmcneill1ug 14, 2014 7:16 AM
    I have IMac OSX 10.9.4, 4GB,Processor 3.06 with Intell2Duo. I would like to check for Malware. I run a TechTool Pro 6 every month and that comes up great.
    When check how much memory I am using, with only Safari open I am using 3.9 and more of her 4.0 memory. She is very. very slow in processing. I had 4000
    trash to clean out and it took her over an hour to expel. Also for some reason Safari will not allow me to click on a link, in my G-mail, and let it go to the page.
    It has a sign saying a pop-up blocker is on and will not let me do it. I must open the stamp to look at my e-mails and if I have redirected link now I can do it.
    I have not changed my preferences so where is this pop-up blocker?
    I have looked at preferences on Safari and Google, which I do not understand Google, and do not see where this blocker could be.
    Malware is something I want to make sure is not on my computer. Tech Tool Pro 6 is all I know of and it does not detect Malware.
    Help.
    Ceil

    Try Thomas Reed's Adware removal tool. He posts extensively in the communities.
    Malware Guide - Adware
    Malware Discussion

  • Since upgrading to Mavericks, 10.9.1, pictures that come attached to emails no longer display.  There is only a blank space that after about 1 minute, has a small box with a question mark.  How can I go back to attached images?

    Since upgrading to Mavericks, 10.9.1, pictures that come attached to emails no longer display.  There is only a blank space that after about 1 minute, has a small box with a question mark.  Double clicking on the box will open the image in a separate window.  It's very slow and tedious for multiple images.  How can I go back to attached and displayed  images?  If I click on "Forward", the images appear instantly in the email to be forwarded.

    Scott,
    My problem seemed to fix itself.  Or, by shutting down the computer one night, instead of putting it to sleep, may have reset something.  Since updating to Mavericks, I always (or usually) let the computer sleep overnight or anytime I'm walking away from it.  A few days ago, I was updating notes for my kids about how to find all my stuff and how to turn on my computer, so I wanted to rewrite the start-up procedures for the iMac, just in case they ever need to.  Well, I shut it down one night so the following morning, I could write down each step.  Lo and behold, the images, etc. are all there again!  Solved, but I'm not sure why.
    Tom

  • I am a Canadian staying in England for a few weeks.  How can I get an iPhoto Book printed win England and sent as a gift to an English relative? With my account, it seems that Apple only allows for my book to be printed in Canada.

    I am a Canadian staying in England for a few weeks.  How can I get an iPhoto Book printed win England and sent as a gift to an English relative? With my account, it seems that Apple only allows for my book to be printed in Canada and then sent to my Canadian address..

    in the iPhoto preferences  change the print products country to the UK and give it a try - there may be some restirctions on billing but it has worked for some people
    LN

  • I formatted and re-installed itunes. now it flashing massage that my ´ipod is synced with another iTunes library. An ipod can be synced with only one library at a time.´ now it is giving 2 options,  1- erase and sync, 2- transfer purchases. what to do?

    i formatted and re-installed itunes. now it flashing massage that my ´ipod is synced with another iTunes library. An ipod can be synced with only one library at a time.´ now it is giving 2 options,  1- erase and sync, 2- transfer purchases. what to do?

    Follow these instructions:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities

  • My iPod touch 4th gen. Won't charge with a enercell charger that I've used since December. It will only charge with the apple USB cord that came with it. And even the takes it about 6 sec. To realize its charging. Help me fix this?

    My iPod touch 4th gen. Won't charge with a enercell charger that I've used since December. It will only charge with the apple USB cord that came with it. And even the takes it about 6 sec. To realize its charging. Help me fix this?

    Yes, I've been using it for months. And I can charge other devices with it. (my iPhone) but something weird just happened..... I kept on pluging it in the iPod and sometimes it would start to chàrge then sometimes it won't charge. Charges every time with the iPhone though.

  • When I synced my phone with my mac, the music that I had in my phone got transferred to my mac. 140 songs to be exact, however I can no longer see the songs on my phone, only the purchased album I have appears. How can I get the songs I had back?

    When I synced my phone with my mac, the music that I had in my phone got transferred to my mac. 140 songs to be exact, however I can no longer see the songs on my phone, only the purchased album I have appears. How can I get the songs I had back?

    Connect your phone to computer, and sync like this. Check the boxes for the playlists, artists, albums you want to sync. Then click Apply. If you have enough space on your phone, you can choose Entire music library.

  • I have a new windows PC and when I registered my account with I Tunes only the recent music that I purchased off I Tunes was in my Library all the music that added to the library is missingÉ

    I have a new PC running windows 8 and when I registered my new account with I Tunes only the recent music that I purchased off I Tunes populated in my music library. The other material that I imported into my library from CD is missing. I am missing several hundred recordings and want to know if it is possible to get them back without having to go back to my old PC and manually make out a missing catalogue of music and re-importing back into my new PCÉ

    Your media is only where you put it.
    Installing iTunes and signing into your iTunes account does not cause media to magically appear.
    Copy the ENTIRE iTunes folder from the old computer or the backup of the old computer to the new computer.
    FYI, there is nothing to import and if you are smart and want to avoid duplicates you will NOT import anything.

  • How to call hr_location_api.create_location for different address style with only those fields that belongs specific to  that address style.

    How to call hr_location_api.create_location for different address style with only those fields that belongs specific to  that address style. It should decide at run time means at run time it will come to know the type of address style and based on that only the fields which belong to address details mapped to calling hr_location_api.create_location.
    Thanks in advance.

    You can create a wrapper package on top of the API (hr_location_api.create_location)
    In the wrapper package you set all the values dynamically based on your requirements(say the style and add_line columns are populated on your conditions) and then you call the API.
    Does that not work ?

Maybe you are looking for

  • Upload address book to iCloud

    I have Lion running on a macbook with an iCloud account and a archived address book.  I have installed Lion from scratch and set everything up.  I set iCloud in system preferences and create an iCloud account in address book.  At this time the addres

  • Adobe Paper Texture Pro Menu not showing up.

    Installed Adobe Paper Texture Pro and when I click on the "pancake" (upper right of panel) all I get is Close or Close Tab. I do not get the full menu, i.e. Load Textures, etc. Please tell me how to get the full menu. I understand now that the PS CC

  • How to Prevent Apple Support Communities from Sending Me Emails?

    Hi, How I can I prevent the Apple Support Communities website / tool from sending me emails? I have disabled all emails in my profile settings (since about six months): Still,  Apple Support Communities keep sending me emails in increasing frequency:

  • Sharepoint Hosting Vanity URL and ADFS 3.0

    Friends, i'm sure you got my question from the subject of this topic. to clarify this we are in progress of deploying a hosted model of sharepoint 2013 with vanity urls and i'm trying to integrate SP 2013 with adfs 3.0 we are planning to use vanity u

  • Is there a way to split the iPad screen without an app?

    I was trying the split the iPad like you can on a PC.  I saw some apps to do but I was wondering if there was a way to do it without an app.  Any suggestions?