15" MBP 2.66 8gb will not sleep ever-Same problem on two identical machines

I purchased the new 2010 MBP about a month ago. It never slept for me right from the time I first used it. This includes option-command-eject hot key, power button, closing lid, it will not go to sleep. All attempts result in the machine going into sleep for ~5 seconds and than waking back up.
I brought it into the Applestore and they ordered me a replacement computer. I received that replacement yesterday and after they did a data transfer and I took it home, it was doing THE EXACT SAME THING.
Any ideas?

These things are rarely really hardware related, tomthin. The problem is much more likely to relate to software installed on your computer which is making calls on the HD or the CPU, or to a peripheral attached to it.
Virus checkers, drive and temperature monitoring software, and network activity are common causes.
You can often get a clue by starting up Console (in your utilities folder) and looking at the console , system and kernel logs , esepceially at around the time you are trying to get it to sleep. Sometimes "Activity Monitor" can throw up some clues, too.
If you usually have anything physically connected to the computer at the time the issue occurs you should try disconnecting it, too. You might also try turning off bluetooth and wireless networking before putting it to sleep , to see if this makes any difference.
Is this a computer to which you have "migrated" things over from an earlier Mac using a an earlier version of the OS? If so, it is quite likely that a 'background" utility of some kind simply needs updating for the new computer.
Cheers
Rod

Similar Messages

  • Computer will not sleep (EVER)

    "When I close the lid the power light on the lid release goes bright but never cycles.
    Also, my MBP will not "wake-up" from said state:
    When I open the lid the light goes out, but computer does not respond. Closing the lid renews the light, but again, it does not cycle, nor wake up when opened again... The volume keys do however make noise when pressed.
    Pressing "Sleep" in the apple menu is fruitless. It does, however, kill F12 to widgets, as well as the other special function commands F9,10,11 and such. It also prevents Apple-Tabbing (simply tabs), and swithcing tabs in FireFox by clicking them. Yet Tab+Up,Down,Left,Right works as should... But these symptoms are probably a result of a failed to-sleep routine."
    This is really becoming a pain, and could use some help!
    I am running the following system:
    OSX 10.4.9
    2.16 GHZ Intel C2D
    2Gb 667 DDR2 SDRAM

    Launch Terminal
    Enter pmset -g | grep hibernatemode
    It will return
    hibernate mode x
    Where x =
    # 0 - Old style sleep mode, with RAM powered on while sleeping, safe sleep disabled, and super-fast wake.
    # 1 - Hibernation mode, with RAM contents written to disk, system totally shut down while “sleeping,” and slower wake up, due to reading the contents of RAM off the hard drive.
    # 3 - The default mode on machines introduced since about fall 2005. RAM is powered on while sleeping, but RAM contents are also written to disk before sleeping. In the event of total power loss, the system enters hibernation mode automatically.
    # 5 - This is the same as mode 1, but it’s for those using secure virtual memory (in System Preferences -> Security).
    # 7 - This is the same as mode 3, but it’s for those using secure virtual memory.
    What is it returning ?
    To set another mode use the command
    sudo pmset -a hibernatemode x
    If your machine was previously set to mode 3 (or 7) and you’ve reverted to the old style sleep mode, you’ve got one more step to take: recover the drive space used up by the copy of your system’s RAM, which was created the last time you slept the machine prior to making the switch. In Terminal, enter these two commands, pressing Return after each and providing your password when asked:
    cd /var/vm
    sudo rm sleepimage
    I suspect the issue is related to the sleep mode set and the space left on your hard drive.

  • Macbook Pro 13" will not sleep when I shut the lid

    Hello Community,
    This is my first time using the forum. I have a macbook pro 13" 2009 model. Recently I had my MBP connected to an external monitor. I shut the lid while it was connected to the monitor and forgot to turn off my bluetooth mouse. Later that night the mouse was bumped, waking my macbook and setting it to clamshell mode. I put it to sleep again, opened the lid and woke it, but the LCD on the laptop did not turn on. I reset the PRAM and the NVRAM with no luck. I disconnected the monitor, rested the P/NVRAM and it would boot with the laptop screen and once everything was loaded my screen went black and then went to sleep on its own. I tried powering on and off using the P/NVRAM key commands...and nothing. So I opened the bottom case and physically disconnect the battery, reconnected the battery, put the bottom plate back on and powered it up. The screen began working again, now I have a new problem, the MBP WILL NOT sleep when I shut the lid anymore. I even reinstalled the OS and still no luck? If anyone has anything helpful that I could try to get this feature working again it would be much appreciated. If there is some terminal command I could try or some other troubleshooting method. I even put a magnet by the right side of the keyboard to try to trigger the sleep switch.
    Any advice would be appreciated.

    I resolved my issue in a very unlikely way. In my earlier post I mentioned that I wiped my hard drive and was starting from scratch. Well I reinstalled windows 7 through bootcamp and it fixed my sleep issue. That's right folks...Windows fixed my mac. I think that it was an EFI issue. I think this because windows 7 uses EFI and during installation it must have reset the sleep values to normal. I feel when you reinstall Mac OSX the EFI partition on the drive should get wiped and reinstalled as well. I also feel that apple should have an option within System Prefs for the user to select what the way is that the computer responds when the lid is shut instead of the ritual of trickery and problems that the clamshell mode can cause.
    Hope this helps someone.

  • MacBook Pro will not sleep with lid open, but now solved, very odd.

    I bought a 2.4 GHz MBP about a week ago, as soon as I got it home I reinstalled the OS and zero-out the drive. Everything appears to work perfect until I noticed that the MBP will not sleep with the lid open.
    But...
    Close the lid, it sleeps.
    Select sleep from menu, it sleeps.
    Let the battery drain down with lid open, laptop sleeps.
    Whent thru painful troubleshooting process, reseting things, permissions, what is installed, running programs...blah blah blah, nothing no difference.
    So, backup the drive using superduper to external firewire and reinstall all over again, just like i did when i first got home, except I did not let it connect to the internet. I went thru and setup everything then connected and performed each update, one at a time looking for what might hinder the sleep process.
    And the result is a big fat zero.
    Same install process as i did the first time, and same updates as the first time. But now the laptop sleeps perfectly.
    Gotta love computers, so very consistant
    Just my .02 input on this wacky issue.

    Try trashing these 3 .plist preferences and reboot. Reset your Energy Saver preferences.
    HD > Library > Preferences > SystemConfiguration > com.apple.AutoWake.plist & com.apple.PowerManagement.plist
    User > Library > Preferences > com.apple.systemuiserver.plist
    Also, look at your system logs in your Console application and see what is causing the "wake event." It could be hardware-related. Do you have any external devices attached, such as a mouse or hub? I've seen Bluetooth problems with wireless BT mice.
    Dave M.
    MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
    Creator of 'Mac611 - Mobile Mac Support' (designed exclusively for an iPhone/iPod touch)

  • HP Envy Will Not Sleep Automatica​lly

    My computer will sleep fine if I tell it to, but it won't do it automatically. That function is critical to my computer's security.
    I confirm that I've told it to sleep after 1 minute, whether on battery or plugged in. If I tell it to dim the screen after a minute, that works fine, but it will not sleep.
    Below is the Power Efficiency Diagnostics Report (Forum removed HTML) -- note the errors.
    I have unplugged all USB devices. I have stopped the WIndows Media Network Sharing Service. I have disconnected from the network (airplane mode). It still will not sleep.
    Please tell me what else to try.
    Thanks.
    Power Efficiency Diagnostics Report Computer Name HP_ENVY Scan Time 2014-05-16T02:26:12Z Scan Duration 60 seconds System Manufacturer Hewlett-Packard System Product Name HP ENVY TS 17 Notebook PC BIOS Date 03/05/2014 BIOS Version F.53 OS Build 9600 Platform Role PlatformRoleMobile Plugged In true Process Count 103 Thread Count 1174 Report GUID {85eba029-391e-4c52-b630-5313c8f32a3c} Analysis Results Errors
    Power Policyisplay timeout disabled (On Battery)
    The display is not configured to turn off after a period of inactivity.
    Power Policyim timeout is disabled (On Battery)
    The display is not configured to automatically dim after a period of inactivity.
    Power Policyisplay timeout disabled (Plugged In)
    The display is not configured to turn off after a period of inactivity.
    Power Policyim timeout is disabled (Plugged In)
    The display is not configured to automatically dim after a period of inactivity.
    System Availability Requestsystem Required Request
    The device or driver has made a request to prevent the system from automatically entering sleep.
    Driver Name \FileSystem\srvnet
    USB Suspend:USB Device not Entering Selective Suspend
    This device did not enter the USB Selective Suspend state. Processor power management may be prevented when this USB device is not in the Selective Suspend state. Note that this issue will not prevent the system from sleeping.
    Device Name HP Wireless Mouse Host Controller ID PCI\VEN_8086&DEV_8C31 Host Controller Location PCI bus 0, device 20, function 0 Device ID USB\VID_03F0&PID_8207 Port Path 2
    USB Suspend:USB Device not Entering Selective Suspend
    This device did not enter the USB Selective Suspend state. Processor power management may be prevented when this USB device is not in the Selective Suspend state. Note that this issue will not prevent the system from sleeping.
    Device Name LSI USB 2.0 Soft Modem Host Controller ID PCI\VEN_8086&DEV_8C31 Host Controller Location PCI bus 0, device 20, function 0 Device ID USB\VID_047E&PID_2892 Port Path 1
    Platform Power Management CapabilitiesCI Express Active-State Power Management (ASPM) Disabled
    PCI Express Active-State Power Management (ASPM) has been disabled due to a known incompatibility with the hardware in this computer.
    Al
    HP Envy Touchsmart 17
    Windows 8.1 Build 9600
    This question was solved.
    View Solution.

    Hi, AQB,
    Yes, I solved it. Here are my notes on the issue:
    See this web site:
    http://mingersoft.com/blog/2011/12/why-wont-window​s-automatically-sleep/
    Better:
    http://helpdeskgeek.com/windows-8/fix-windows-8-1-​will-sleep/
    From the command prompt:
    powercfg -requestsoverride driver \filesystem\srvnet system
    or
    powercfg /requestsoverride driver srvnet system
    or
    powercfg /energy /output c:\temp\requests.htm
    See this web site:
    http://mingersoft.com/blog/2011/12/why-wont-window​s-automatically-sleep/
    Better:
    http://helpdeskgeek.com/windows-8/fix-windows-8-1-​will-sleep/
    Al
    HP Envy Touchsmart 17
    Windows 8.1 Build 9600

  • HT3302 My Ipod touch 8gb will not turn back on no matter what i do i have tried just the power button, the power button and home button, and connecting it to the computer and the battery wasn't close to being dead non of them work what do i do?

    My Ipod touch 8gb will not turn back on no matter what i do i have tried just the power button, the power button and home button, and connecting it to the computer and the battery wasn't close to being dead non of them work what do i do?

    Try:                           
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • My iMac running lion will not sleep if an external HDD is connected.

    My Imac will not sleep if the external HDD is connected. This just began to occur. If I unplug the drive it goes to sleep. This doesn't happen with any oter USB pereferals.
    Thanks in advance.

    From the menu bar, select
     ▹ System Preferences... ▹ Network
    Click the Assist me button and select Assistant. Follow the prompts. How far do you get?

  • After installing recent java + security update, computer will not sleep

    After installing the recent java, daylight savings, and the security update. my computer will not sleep. Does anyone else have this problem? I do have an adaptec usb2 card installed but nothing is plugged into it. Also i don't have any Ipods or external things plugged in. I have had the same setup for the past year with no problems, now it will not sleep. I have also tried repairing the permissions. Please help

    When you select Sleep from the Apple Menu nothing happens, is that correct? Try this: Go menu > Home > Library > Preferences. Drag the whole of the Preferences folder to the desktop. Restart your mac, don’t worry if things look different, you have not lost anything. Can the mac sleep now? If yes, then its a damaged or corrupted .plist or preference. If you are using Apple Mail, drag the com.apple.mail.plist back to the new preferences folder created on reboot, you dont really need anything else but keep hold of the old preferences (the one you dragged to your desktop) just in case for a month or two. If everything else is OK you can safely delete it. If it has not cured the problem then remove the new preferences folder created on reboot by taking it to the trash, drag back the preferences folder you moved to the desktop and reboot. Now reinstall a clean OS. See how you go from there

  • After installing recent java update, computer will not sleep.

    After installing the recent java, daylight savings, and the security update. my computer will not sleep. Does anyone else have this problem? I do have an adaptec usb2 card installed but nothing is plugged into it. Also i don't have any Ipods or external things plugged in. I have had the same setup for the past year with no problems, now it will not sleep. I have also tried repairing the permissions. Please help

    A number of sleep-related issues can appear after incremental Mac OSX updates, including the inability to properly go to sleep, problems waking from sleep, and having your display go to sleep without your Mac going to sleep. The most common culprit is Bluetooth. Try these tips to fix your sleep problems.
    WAKE UP
    In System Preferences>Bluetooth, uncheck Allow Bluetooth Devices To Wake This Computer. If you are using a Bluetooth mouse and keyboard, you'll have to wake your Mac by pressing the power button.
    FILE CORRUPTION
    Your Bluetooth preference file may be corrupt-you'll need to delete it. Turn Bluetooth off, then go to the /Users/user name/Library/Preferences folder. Look for a file called com.apple.Bluetooth.plist and trash it.The OS will create a new preference file when you enable Bluetooth again.
    ENERGY SAVER
    If you have issues with a Mac or display that goes to sleep at inappropriate times, you may have a problem with Energy Saver. Delete the following .plist files and restart:
    -/Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist
    -/Users/username/Library/Preferences/com.apple.systemuiserver.plist--
    (username is your name or System Administrators name)
    -/Library/Preferences/SystemConfiguration/com.apple.AutoWake.plist
    A restart is very important after deleting these plists. After a reboot your Mac will then generate new ones.
    Some, in these forums, have had luck fixing sleep issues downloading the Combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try.
    Yours would be the 10.4.8 Combo update. Others reading, download the combo update that applies to you!
    Cheers!
    DALE

  • Will Not Sleep In Energy Saver Mode

    My iMac G5 20" 1.8Ghz will not sleep when I set it to sleep in the energy saver panel. This just started for no specific reason a few months ago. It will sleep fine when selected from the Apple menu. I have been through the discussions and no one seems to have a good fix for this. I have repaired permissions, reset the PRAM and SMU, and tried all the different configurations in energy saver. I called AppleCare and they seemed not to know anything about this issue. They recommened an archive and reinstall of the operating system. I feel this is kind of drastic for this and I have not yet tried it unless I can see that other people have done it and it works. My computer is in the repair program for the power supply problem and it has an updated power supply since the original actually smoked and Apple replaced it. I was wondering if anyone out there has had this same sleep issue and got it resolved?

    Well I finally decided to try and delete an application that I suspected could be a problem not allowing my computer to sleep automatically. That application is LAST FM a music service from the UK which is actually quite good. I suspected it was a problem since it would always launch when I opened iTunes and asked if I wanted to share my iTunes library with the LAST FM group which I did not. I selected I did not want to share in the LAST FM preferences but it still opened anyway when I launched iTunes. I deleted the program and repaired disk permissions and *It Worked*, my computer will now go to sleep with the settings I selected in energy saver. I know there are other people out there with this problem I would first look at this application and others that are probably running in the backround causing your computer not to sleep automatically. I am a firm believer in trying to work up from the easiest solution before taking the drastic approach, such as a system reinstall, or a logic board replacement. I did take Nikki's suggestion seriously. My power supply had been replaced in the repair program and my logic board did not meet the criteria for replacement since it was not exibiting the symptoms that required its replacement such as video and power problems.

  • Mac book pro will not sleep after i installed mavericks

                mac book pro will not sleep after i installed mavericks the sleep indicator light stays solid and fans still run but the display turns off

                mac book pro will not sleep after i installed mavericks the sleep indicator light stays solid and fans still run but the display turns off

  • My imac display will not sleep

    I set it to one minute and wait and the display will not sleep

    I set it to one minute and wait and the display will not sleep

  • I phone will not "sleep" after non use of 1 hour. How do I fix this?

    i phone will not "sleep" after non use of 1 hour. How do I fix this?

    You obviously have a faulty SIM card. Go to an Apple store or a phone store and get a replacement SIM card.

  • Will not sleep after OS 10.9.4 update

    Mac Pro 2013 will not sleep, either manually or through Energy Saver. It sleeps for about 2 seconds, then back on. It worked fine before the update!

    Test after each of the following steps that you haven’t already tried:
    Step 1
    Take all the steps suggested in this support article. That's the starting point for any further effort to solve the problem. Skipping any of those steps may mean that the problem won't be solved. Note that, as stated in the article, the computer will not sleep if Internet Sharing is enabled.
    Step 2
    From the menu bar, select
               ▹ System Preferences ▹ Accessibility ▹ Speakable Items: Off
    Step 3
    Select
               ▹ System Preferences ▹ Bluetooth ▹ Advanced...
    and uncheck both boxes marked
              Open Bluetooth Setup Assistant at startup if...
    Step 4
    Reset the SMC.
    Step 5
    Disconnect all wired peripherals and test. If you use a wired keyboard and/or mouse, use different ones. You must rule out the wired keyboard and mouse as possible causes of the problem.
    Step 6
    Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Safe mode is much slower to start and run than normal. Don’t launch any applications at first. If sleep still doesn’t work properly, back up all data andreinstall the OS. After that, if you still have the issue, make a “Genius” appointment at an Apple Store to have the machine tested.
    If sleep now works as expected, go on to the next step.
    Step 7
    Still in safe mode, launch the usual set of applications that are running when you have the problem, including your login items, one at a time, testing after each one. Some applications may not work; skip them. You might be able to identify the cause of the problem this way.
    Step 8
    If sleep is still working after you’ve launched all the usual applications, restart as usual (not in safe mode) and test again. If sleep still works, you’re done, at least for the moment.
    If you still have the sleep issue after restarting out of safe mode, post again.

  • MacBook will not sleep automatically since Snow Leopard install

    Hello. I am having a serious issue with my MacBook since upgrading to Mac OS X Snow Leopard. My MacBook (Late 2008 Aluminum, 2.4 GHz) will not go to sleep automatically anymore. If I select "Sleep" from the Apple menu it will sleep fine. However, it will not sleep according to my Energy Saver preference pane which says sleep at 1 min each (Display and Computer). Another thing to keep in mind is that my display sleeps perfectly normally. However, the computer itself will not sleep.
    Here are the things that I have tried so far:
    - Reinstall 10.6.2 combo updater
    - Remove Energy Saver preferences and entire System Configuration folder
    - Made sure that no hardware or software is interrupting sleep
    - Reset PRAM and SMC
    I am running Mac OS X 10.6.2 with ALL updates and firmware installed.
    Please help me figure this out as it is a serious issue. Thanks.
    Message was edited by: celticpride678
    Message was edited by: celticpride678

    12/30/09 6:05:55 PM UserEventAgent[115] ** ERROR: SCNetworkSignatureCopyActiveIdentifiers returned nil
    12/30/09 6:09:31 PM Camino[151] * WARNING: Method selectRow:byExtendingSelection: in class NSTableView is deprecated. It will be removed in a future release and should no longer be used.
    12/30/09 6:09:43 PM Camino[151] -deltaZ is deprecated for NSEventTypeMagnify. Please use -magnification.
    12/30/09 6:21:21 PM Camino[461] * WARNING: Method selectRow:byExtendingSelection: in class ExtendedTableView is deprecated. It will be removed in a future release and should no longer be used.
    12/30/09 6:23:38 PM Finder[103] Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found. Did find:
    /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    12/30/09 6:23:38 PM com.apple.Finder[103] Finder: OpenScripting.framework - scripting addition "/Library/ScriptingAdditions/Adobe Unit Types.osax" declares no loadable handlers.
    12/30/09 6:23:41 PM System Preferences[548] .scriptSuite warning for result type of command 'timedLoad' in suite 'SystemPreferences': the type NSNumber ('long') doesn't match the result Apple event code ('doub').
    12/30/09 6:23:43 PM System Preferences[548] ILLogger ILMediaBrowserPathWatcher: ** Error in ILMediaBrowserPathWatcher startFSEventStream failed to start for paths: (
    "/Users/Brian/Pictures/iPhoto Library"
    12/30/09 6:23:43 PM System Preferences[548] ILLogger ILMediaBrowserPathWatcher: ** Error in ILMediaBrowserPathWatcher startFSEventStream failed to start for paths: (
    "/Users/Brian/Pictures/iPhoto Library",
    "/Users/Brian/Library/Preferences"
    12/30/09 6:24:06 PM System Preferences[548] It looks like we crashed last time. Reverting to default screen saver.
    12/30/09 6:24:17 PM com.apple.diskmanagementd[557] /: no supported helper partitions to update.
    12/30/09 6:24:28 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x11a70b000) malloc: * auto malloc[548]: error: GC operation on unregistered thread. Thread registered implicitly. Break on autozone_thread_registrationerror() to debug.
    12/30/09 6:24:45 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x2009f1300, break on autorefcount_underflowerror to debug.
    12/30/09 6:25:24 PM System Preferences[548] * -[NSCFArray objectAtIndex:]: index (5) beyond bounds (5)
    12/30/09 6:26:32 PM System Preferences[548] * -[NSCFArray removeObjectAtIndex:]: index (5) beyond bounds (5)
    12/30/09 6:28:03 PM System Preferences[548] * -[NSCFArray removeObjectAtIndex:]: index (4) beyond bounds (4)
    12/30/09 6:28:03 PM System Preferences[548] * -[NSCFArray removeObjectAtIndex:]: index (4) beyond bounds (4)
    12/30/09 6:28:04 PM System Preferences[548] * -[NSCFArray removeObjectAtIndex:]: index (4) beyond bounds (4)
    12/30/09 6:28:04 PM System Preferences[548] * -[NSCFArray removeObjectAtIndex:]: index (4) beyond bounds (4)
    12/30/09 6:28:32 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x200b9bc40, break on autorefcount_underflowerror to debug.
    12/30/09 6:28:32 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x200b9bbe0, break on autorefcount_underflowerror to debug.
    12/30/09 6:28:32 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x200b9bb00, break on autorefcount_underflowerror to debug.
    12/30/09 6:28:32 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x200b9bba0, break on autorefcount_underflowerror to debug.
    12/30/09 6:28:32 PM [0x0-0x24024].com.apple.systempreferences[548] System Preferences(548,0x7fff7001abe0) malloc: reference count underflow for 0x200b9bb80, break on autorefcount_underflowerror to debug.
    12/30/09 6:29:51 PM com.apple.launchd.peruser.502[97] ([0x0-0x28028].com.apple.speech.feedbackservicesserver[575]) Exited: Killed
    12/30/09 6:29:51 PM com.apple.launchd.peruser.502[97] ([0x0-0xb00b].com.apple.speech.synthesis.SpeechSynthesisServer[127]) Exited: Killed
    12/30/09 6:30:11 PM com.apple.launchd[1] * launchd[1] has started up. *
    12/30/09 6:30:38 PM com.apple.SystemStarter[21] Starting HP Trap Monitor
    12/30/09 6:30:41 PM com.apple.launchctl.Aqua[97] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 6:30:41 PM com.apple.launchd.peruser.502[95] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    12/30/09 6:30:41 PM com.apple.launchctl.Aqua[97] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 6:30:44 PM com.apple.launchd.peruser.502[95] (com.apple.Kerberos.renew.plist[116]) Exited with exit code: 1
    12/30/09 6:31:12 PM com.apple.WindowServer[62] Wed Dec 30 18:31:12 Brian-Roths-MacBook.local WindowServer[62] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 7:17:14 PM SyncServer[211] [110f20] |SyncServer|Warning| Refreshing watchdog because of a calendar time change alert.
    12/30/09 7:17:14 PM UserEventAgent[112] ** ERROR: SCNetworkSignatureCopyActiveIdentifiers returned nil
    12/30/09 8:04:33 PM UserEventAgent[112] ** ERROR: SCNetworkSignatureCopyActiveIdentifiers returned nil
    12/30/09 8:18:10 PM com.apple.launchd.peruser.502[95] ([0x0-0x9009].com.Growl.GrowlHelperApp[123]) Exited: Terminated
    12/30/09 8:22:34 PM Installer[1364] PackageKit: * Missing bundle identifier: /Library/Receipts/NeoOffice-3.0.1-Intel.pkg
    12/30/09 8:22:34 PM Installer[1364] PackageKit: * Missing bundle identifier: /Library/Receipts/NeoOffice-3.0.1-Patch-1-Intel.pkg
    12/30/09 8:22:34 PM Installer[1364] PackageKit: * Missing bundle identifier: /Library/Receipts/NeoOffice-3.0.1-Patch-2-Intel.pkg
    12/30/09 8:27:06 PM com.apple.launchd.peruser.502[95] ([0x0-0xa00a].com.apple.speech.synthesis.SpeechSynthesisServer[124]) Exited: Killed
    12/30/09 8:27:06 PM com.apple.launchd.peruser.502[95] (0x1001014d0.mach_init.rcd[436]) Exited: Killed
    12/30/09 8:27:43 PM com.apple.launchd[1] * launchd[1] has started up. *
    12/30/09 8:35:53 PM com.apple.launchd.peruser.502[97] ([0x0-0x10010].com.apple.DiskUtility[142]) Exited: Killed
    12/30/09 8:35:53 PM com.apple.launchd.peruser.502[97] ([0x0-0xa00a].com.apple.speech.synthesis.SpeechSynthesisServer[127]) Exited: Killed
    12/30/09 8:36:12 PM com.apple.launchd[1] * launchd[1] has started up. *
    12/30/09 8:36:47 PM com.apple.SystemStarter[21] Starting HP Trap Monitor
    12/30/09 8:36:49 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:36:49 PM com.apple.launchd.peruser.502[97] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    12/30/09 8:36:49 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:36:51 PM com.apple.launchd.peruser.502[97] (com.apple.Kerberos.renew.plist[117]) Exited with exit code: 1
    12/30/09 8:38:04 PM com.apple.launchd.peruser.502[97] ([0x0-0xa00a].com.apple.speech.synthesis.SpeechSynthesisServer[123]) Exited: Killed
    12/30/09 8:38:42 PM com.apple.launchd[1] * launchd[1] has started up. *
    12/30/09 8:39:17 PM com.apple.SystemStarter[21] Starting HP Trap Monitor
    12/30/09 8:39:19 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:39:19 PM com.apple.launchd.peruser.502[97] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    12/30/09 8:39:19 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:39:20 PM com.apple.launchd.peruser.502[97] (com.apple.Kerberos.renew.plist[118]) Exited with exit code: 1
    12/30/09 8:39:25 PM com.apple.WindowServer[65] Wed Dec 30 20:39:25 Brian-Roths-MacBook.local WindowServer[65] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 8:39:40 PM com.apple.launchd.peruser.502[97] ([0x0-0xa00a].com.apple.speech.synthesis.SpeechSynthesisServer[126]) Exited: Killed
    12/30/09 8:42:44 PM com.apple.launchd[1] * launchd[1] has started up. *
    12/30/09 8:43:16 PM com.apple.SystemStarter[21] Starting HP Trap Monitor
    12/30/09 8:43:18 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:43:18 PM com.apple.launchd.peruser.502[97] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    12/30/09 8:43:18 PM com.apple.launchctl.Aqua[99] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 8:43:20 PM com.apple.launchd.peruser.502[97] (com.apple.Kerberos.renew.plist[118]) Exited with exit code: 1
    12/30/09 9:03:31 PM com.apple.WindowServer[66] Wed Dec 30 21:03:31 Brian-Roths-MacBook.local WindowServer[66] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 10:42:25 PM com.apple.loginwindow[29] Wed Dec 30 22:42:25 Brian-Roths-MacBook.local loginwindow[29] <Warning>: CGSShutdownServerConnections: Detaching application from window server
    12/30/09 10:42:26 PM com.apple.loginwindow[29] Wed Dec 30 22:42:26 Brian-Roths-MacBook.local loginwindow[29] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 10:42:26 PM com.apple.loginwindow[29] Wed Dec 30 22:42:26 Brian-Roths-MacBook.local loginwindow[29] <Warning>: CGSDisplayServerShutdown: Detaching display subsystem from window server
    12/30/09 10:42:27 PM com.apple.WindowServer[600] Wed Dec 30 22:42:27 Brian-Roths-MacBook.local WindowServer[600] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 10:42:32 PM com.apple.loginwindow[599] 2009-12-30 22:42:32.557 migCacheCleanup[617:903] Flushing Cache Locations...
    12/30/09 10:43:09 PM com.apple.coreservicesd[64] ThrottleProcessIO: throttling disk i/o
    12/30/09 10:47:12 PM com.apple.loginwindow[599] Wed Dec 30 22:47:12 Brian-Roths-MacBook.local loginwindow[599] <Warning>: CGSShutdownServerConnections: Detaching application from window server
    12/30/09 10:47:12 PM com.apple.loginwindow[599] Wed Dec 30 22:47:12 Brian-Roths-MacBook.local loginwindow[599] <Warning>: CGSDisplayServerShutdown: Detaching display subsystem from window server
    12/30/09 10:47:13 PM com.apple.loginwindow[599] Wed Dec 30 22:47:13 Brian-Roths-MacBook.local loginwindow[599] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 10:47:13 PM com.apple.WindowServer[698] Wed Dec 30 22:47:13 Brian-Roths-MacBook.local WindowServer[698] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
    12/30/09 10:47:20 PM com.apple.launchctl.Aqua[711] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 10:47:20 PM com.apple.launchd.peruser.502[97] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
    12/30/09 10:47:20 PM com.apple.launchctl.Aqua[711] launchctl: Dubious permissions on file (skipping): /Users/Brian/Library/LaunchAgents
    12/30/09 10:47:22 PM com.apple.launchd.peruser.502[97] (com.apple.Kerberos.renew.plist[729]) Exited with exit code: 1
    12/30/09 10:47:44 PM com.apple.launchd[1] (0x100102d30.mach_init.mdworker[684]) Exited: Killed
    12/30/09 10:47:44 PM com.apple.launchd[1] (com.apple.launchd.peruser.503[593]) Exited: Killed
    12/30/09 10:48:41 PM com.apple.launchd[1] (0x100102d30.mach_init.mdworker[783]) getpwuid("503") failed
    12/30/09 10:48:41 PM com.apple.launchd[1] (0x100102d30.mach_init.mdworker[783]) Exited with exit code: 1
    12/30/09 10:48:41 PM com.apple.launchd[1] (0x100102d30.mach_init.mdworker) Failed to check-in!
    12/30/09 10:58:17 PM UserEventAgent[112] ** ERROR: SCNetworkSignatureCopyActiveIdentifiers returned nil
    12/30/09 11:18:13 PM [0x0-0x22022].com.apple.systemevents[365] com.apple.FolderActions.enabled: Already loaded
    12/30/09 11:19:23 PM UserEventAgent[112] ** ERROR: SCNetworkSignatureCopyActiveIdentifiers returned nil

Maybe you are looking for

  • Can't open .mov video file

    I have a .mov file make with final cut on a mac with the Mjpeg A compressor , I try to open the file with my quicktime 7.4.1 on my PC , the error 2048 appears: "is not a valid file format " . I try with VLC , and give me another bad message " MP4 plu

  • Not all calendar entries sync with desktop & Outlook

    I'm running V5 of the DM and the OS on my 8900. I have 4 different email addresses on by blackberry - 2 regular internet email, 1 gmail and 1 facebook. Calendar entries from only one of my internet email address will sync back to Outlook. I just trie

  • Component determination in BOM

    Hello, I have to include a procedure in a BOM component to determine if that component must be selected or not according to a caracteristic but the option is not enabled in the BOM item. Does anybody know if it is a customizing issue and if yer, wher

  • What are the events in Module Pool Programming ?

    hi, what are the events in Module Pool Programming ??? thx

  • Inserting video clip and have both audios at once

    Hi everyone, hopefully somone can help answer my question.  My friend has a video blog and the person who used to do all of his technical stuff is no longer with him, so he's trying to figure it all out, and I figured I'd try to help him. In iMovie,