1522 Radio status down

My client bought 10 AIR-LAP1522AGs and a 4402 controller. They want to use them in pairs to establish 5 x wireless bridges. I have configied the controller and have added all the APs into the controller as either RAPs or MAPs.
I cannot figure out how to turn on the radios. I have downloaded several Cisco docs but am unable to find the answer to this seemingly simple question.
Jeff

So without the radios up, does this mean you primed the MAPs to join over ethernet interface? Otherwise, for them to be joined, the radios would need to be up..
Anyhow, if the radios are all down, it sounds like you may have 802.11a or 802.11b/g Globally Disabled (GUI > Wireless > 802.11a > network > enable 802.11a)...........................
Other than that, I suppose your AP Admin mode could be Disabled instead (GUI > Wireless) APs each have an admin status....
Or is the problem not that the radios are "off" but that something isn't working on them...?

Similar Messages

Cisco Wireless AP radio interface shutdown/Operation Status Down

Hi,
I am trying to troubleshoot the cause of the wireless AP 1142 radio shutdown; I was wondering where may be a good place to start on it/possibility of the radio shutting down. Once the radio is shown as down; I would just need to re-enable (disable/enable) it and the status changes to up status. I have attached a screen catpure of the radio interface showning down.
The AP radios shutting down is intermittent; some APs has their "A/N" radio interface shutdown while others has their "G/N" radio interface shutdown. Not too sure what may most likely be causing it to shutdown?
Any input is appreciated.
Thanks.

Do you have controller ?? if yes then posts out put of sh sysinfo commad.
Paste the output of sh version command from AP.
Also check:
1. Choose Wireless > 802.11a/n or 802.11b/g/n > Network
Select the 802.11a (or 802.11b/g) Network Status check box to enable the 802.11a or 802.11b/g band.
2. Wireless > Access Points > All APs then click on specific AP and make sure admin status is enable.
Reagrds

1300 Bridge fa0 port status down

I have a remote 1300 bridge whose fa0 port consistently goes down after working well for over a week. It shows the port as admin up but line status down - no carrier. It plugs directly into a 1200 ap. I have tried to hard code the speed and duplex but the option to hard code the speed is not available. Any ideas?

Hi
yes the console port on the power injector is is console port for the AP. probably the best way to recover the bridge is to connect the 1310 to a laptops etherernet port and use the console port to learn the IP of the 1310 then manage the 1310 with the GUI it can be done with the CLI but if you have not done a wireless bridge before stick with the GUI. Both 1310's need to be on the same subnet, this is for management not for bridging. the bridging is at level 2 unless you use VLANS but with the routers that should not be an issue. once you have configured the Root router save the config and use it to to congigure the non-root router changing the IP address and the role to Non Root. plug the network cables into the the apropriate router ports and you should be set.
this is assuming you know the userid/passwords for the AP's the default was Cisco/Cisco.
if the antennas are alinged your bridge should be reliable.
based on the signal level between the AP's i would disable the B data rates use the G data rates and possibley disable the higher data rates if the radio stats show to many retrys, mor than 10%.
Bill

How to remove the pop-up window ''Wireless Radio Status" for t430s

Hi, I have owned my t430s for now about 2 years without any major complaints recently I've had to use the fn + f5 function quite frequently, because of my poor internet connection. so that way i can reset which signal I want to choose because the default signal I am connected to is not mine. My problem is similar to what is posted here: https://forums.lenovo.com/t5/X-Series-Tablet-and-Helix/how-to-remove-the-pop-up-window-Wireless-Radio-Status/td-p/1191059 I really want to get rid of the pop up for this feature, I've tried to follow what the other thread user's have done and try out their solutions but it does not work for my t430s i tried changing the pmev thing to what was posted in the thread. Can anyone help me? Thanks!

I already tried that as mentioned in my original post, it doesn't work. I still get the pop up message: this is me pressing fn + f5

AP "A" Radio is Down

AP is connected to 6500 switch with "inline power" turned off. Using the supplied power supply to power the AP unit. B/G radio shows up but A radio shows down. WCS 4.2

I figured it out. I did not enable it on the controller side.

Concurrent processing status down in OAM

Hi ,
From OAM->Applications Dashboard ->Overview
the status for concurrent processing shows down but infact it is up
I also checked from OAM->Hosts->view configuration
whereas here the status for concurrent processing is up.
thanks all in advance..
applications version: 11.5.10.2

Hi,
Please see if these documents help.
Note: 405375.1 - OAM Reports 'Internal Concurrent Manager Found Node To Be Down.' When Node is Up
Note: 419823.1 - OAM: Web Components Status: Shows Down Even When The System Works Fine
Note: 309271.1 - Web Components Status in OAM Shows All Down Even When the System Works Fine
Note: 434569.1 - OAM application dashbord shows all the web components with status down whereas they are up
Note: 287415.1 - Host Status In Application Dashboard Overview Tab Shown As Down in OAM
Regards,
Hussein

IDSM-2(5.0)inline mode- Pair Status=down??

I have trouble with configuring idsm-2 inline mode(5.0).
it seems that traffic doesn't go through idsm.
I chechked it on command: sh interfac gi0/7(idsm mode)
the 'pair Status=down'(below) shows that, i think.
moreover, total packet received doesn't increase.
how do i solve it?
Please help!
xxsystems# sh int gigabitEthernet0/7
MAC statistics from interface GigabitEthernet0/7
Media Type = backplane
Missed Packet Percentage = 0
Inline Mode = Paired with interface GigabitEthernet0/8
Pair Status = Down
Link Status = Up
Link Speed = Auto_1000
Link Duplex = Auto_Full
Total Packets Received = 38
Total Bytes Received = 2584
Total Multicast Packets Received = 38
Total Broadcast Packets Received = 0
Total Jumbo Packets Received = 0
Total Undersize Packets Received = 0
Total Receive Errors = 0
Total Receive FIFO Overruns = 0
Total Packets Transmitted = 12
Total Bytes Transmitted = 1152
Total Multicast Packets Transmitted = 0
Total Broadcast Packets Transmitted = 12
Total Jumbo Packets Transmitted = 0
Total Undersize Packets Transmitted = 0
Total Transmit Errors = 0
Total Transmit FIFO Overruns = 0

You can only pair interfaces on your sensor if your sensor is capable of inline monitoring.
http://www.cisco.com/en/US/products/sw/secursw/ps2113/products_installation_and_configuration_guide_chapter09186a00803eb069.html

Apple TV radio shuts down after 10 minutes

Apple TV radio shuts down after 10 minutes. Can not find out why. Could version 7.0 be the problem?

Welcome to the Apple Community.
Seems to be an issue for a large number of users, probably need to wait for a fix.

IOS 1230 AP Radio shuts down

I have a unique problem in which I have my Cisco SE involved in trying to correct. When using an IOS based 1230 AP in one of my locations the RADIO interface will turn off (shut down) even though it appears as being up. All associatins are lost and the only way to reassociate to the AP is by restarting the AP. I have the latest code running for the Vxworks 1200 AP and this problem does not happen. I also have the IOS based 1230 AP deployed at all my other locations with zero problems. Cisco has provided me with a spectrum analyzer thinking it was some interference, but we have not seen any interference. Is anyone else having this problem? Please reply of e-mail me I would love to discuss this with you.
PK

Hmm... I have had problems with the 802.11a (5Ghz) radio shutting down. It just says something like "DOT11-RADIO-FAILED" I believe in the logs and shows that it was down. Had the unit replaced once and the problem seemed to go away for quite awhile but did notice the radio failed again last week sometime and had to reboot again.
I thought it might be heat related since it was mounted on a "cloth" wall without the right mounting bracket and might have had the vents covered, but that's not the case now.

WIPS service status down

Cant get my wIPS service running...
Running 24 controllers( 4400s and wisms) , ver 6.0.188 using WCS ver 6.0.170 with 800+ 1140 access points
Just installed an MSE 3310, WCS sees it and knows what it is.
I cant seem to get the wIPS service to come up... status on WCS ( and MSE) is   "admin status enabled" .."operational status down"
Is there another step/trick to get it running ?
Thanx

Thanks Nael,
MSE ver = 5.2.91
WCS ver = 6.0.170
stopped service via msed stop
grep for any msed processes.... none shown
started service via msed start
echos back with the attached file output
Starting MSE Platform
Type: NAME Value: Chassis
Type: DESCR Vlaue: Cisco 3310 Mobility Services Engine
Type: PID Value: AIR-MSE-3310-K9
Type: VID Vlaue: V01
Type: SN Value: < removed>
Starting MSE Platform, waiting to check the status
Starting MSE Platform, waiting to check the status
Starting MSE Platform, waiting to check the status
MSE Platform is up, getting the status
Unable to get MSE status.      Retrying status fetch -
Unable to get MSE status.      Retrying status fetch -
Unable to get MSE status.      Retrying status fetch -
"getserverinfo" returns the same output

Radio going down on 1310AP

Hi there, I'm experiencing some issues with a 1310 LWAPP on a University, here is the scenario:
The AP is directed to some specific classrooms and at a certain point the radio goes down or at least there is no more communication between the clients and the AP, but the association in the computers remain the same for a couple of minutes, after that the link goes down, but the weird thing is that the communciation to the AP via Ethernet remains up. We tested this and the ping's all were responding while the radio was down.
Steps already done:
-A new 1310 has been tested, same results.
-A new power injector, same results.
-The UTP cabling between the power injector and the IDF has been changed, same results.
-The port to which the AP was connected at the IDF switch was changed, same results.
I'm thinking as a possible solution:
-Replacing the coax cabling between the power injector and the AP (not more than 15 ft).
-Ensure the AC voltage at the power outlet is delivered correctly (110v) not less, not more.
I'm wondering if this steps may be causing the device(s) to fail in such a way, because if it is not receiving the appropriate ammount of power the radio module simply goes down, but as the ethernet module requires less power it remains up.
What do you think?
Any recommendation is more than welcomed; too much time has been dedicated without success.
Thanks in advance!

For the troubleshooting chech the Red color indicates an overcurrent or overvoltage error condition disconnect input power from the power injector, check all coax cable connections for a possible short, wait approximately 1 minute, and reconnect input power to the power injector. If the LED turns red again, contact technical support for assistance.
The power injector requires approximately 50 seconds to recover from an overcurrent or overvoltage condition.
Off indicates input power is not available verify that the power module is connected to the power injector and that AC power is available or that 12- to 40-VDC input power is connected to the power injector.

Oper status down

HI,
I recently bought a Cisco 2504 Wireless Controller and a couple of access points (Cisco 1600 Series). Initially the controller had the 7.0.x.x firmware and from what i read on Cisco website it seems that this version is incompatible with my access points, so I updated the firmware on the controller to the latest version (7.4.110.0.). The access points were intially autonomous, so I installed the latest conversion to lightweight iOS image (ap1g2-rcvk9w8-tar.152-4.JA1). All work beautiful and I was happy until i discovered that after the acces points succesfully join the controller the radio interfaces won't come up. On the controller i get the following messages:
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:7c:95:f3:6c:c6:30 Cause=Unknown Reset Status:NA
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:7c:95:f3:6c:c6:30 Cause=Unknown Reset Status:NA
And here's what the acces point displays in logging mode:
*Sep 27 06:35:01.169: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.10.1, mask 255.255.255.0, hostname APc08c.601f.260d
Translating "CISCO-CAPWAP-CONTROLLER.xxx.local"...domain server (10.0.0.1) [OK]
*Sep 27 06:35:03.605: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Sep 27 06:35:13.609: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 27 06:35:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.10.5 peer_port: 5246
*Sep 27 06:35:02.491: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.10.10.5 peer_port: 5246
*Sep 27 06:35:02.491: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.10.5
*Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.10.5
*Sep 27 06:35:03.131: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 27 06:35:03.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 27 06:35:03.259: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLC_Intranet
*Sep 27 06:35:03.311: ac_first_hop_mac - IP:10.10.10.5 Hop IP:10.10.10.5 IDB:BVI1
*Sep 27 06:35:03.311: Setting AC first hop MAC: 4c00.8259.4ee0
*Sep 27 06:35:03.311: ac_first_hop_mac - IP:10.10.10.5 Hop IP:10.10.10.5 IDB:BVI1
*Sep 27 06:35:03.311: Setting AC first hop MAC: 4c00.8259.4ee0
*Sep 27 06:35:03.683: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Sep 27 06:35:04.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 27 06:35:04.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
I must metion that all settings on the controller are fine (the access points interfaces are set to enable), but they just don't want to come up. I'm completely baffled by this problem and I don't know what to do next ? Can someone explain what's happeining ?
PS: The access point are powered by their standard AC-DC power supply (not over PoE).

Thanks for replies! One of the first thing that I did was to configure a NTP server, so the controller is time synchronized. Aslo I manually enable each radio interface.
Here is the output for "show ap config 802.1b" (partial output):
Cisco AP Identifier.............................. 14
Cisco AP Name.................................... APc08c.601f.260d
Country code..................................... RO - Romania
Regulatory Domain allowed by Country............. 802.11bg:-E     802.11a:-E
AP Country code.................................. RO - Romania
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... c0:8c:60:1f:26:0d
IP Address Configuration......................... DHCP
IP Address....................................... 10.10.10.7
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.10.10.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.4.110.0
Boot Version ................................... 15.2.2.0
Mini IOS Version ................................ 7.5.1.73
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP1602E-E-K9
AP Image......................................... C1600-K9W8-M
IOS Version...................................... 15.2(2)JB2$
Reset Button..................................... Enabled
AP Serial Number................................. FGL1735X02L
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
For the 802.11a interface things are almost the same.
Output for show sysinfo:
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... WLC_Intranet
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.10.10.4
Last Reset....................................... Software reset
System Up Time................................... 3 days 5 hrs 33 mins 41 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Output from "show time":
Time............................................. Sun Sep 29 19:22:01 2013
Timezone delta................................... 0:0
Timezone location................................
NTP Servers
    NTP Polling Interval.........................     3600
     Index     NTP Key Index     NTP Server      NTP Msg Auth Status
       1              0        x.x.x.x       AUTH DISABLED
Output from "show verion" on one of the APs:
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 29-Jul-13 12:35 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
APc08c.601f.260d uptime is 30 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602E-E-K9    (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1735X02L
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C0:8C:60:1F:26:0D
Part Number                          : 73-14508-04
PCA Assembly Number                  : 000-00000-00
PCA Revision Number                  :
PCB Serial Number                    : FOC17292D61
Top Assembly Part Number             : 800-38553-01
Top Assembly Serial Number           : FGL1735X02L
Top Revision Number                  : A0
Product/Model Number                 : AIR-SAP1602E-E-K9
Configuration register is 0xF
Output from "show inventory " on one of the APs:
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-SAP1602E-E-K9 , VID: V01, SN: FGL1735X02L
Output from "show inventory " on one of the APs:
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       10.10.10.7     YES DHCP     up                    up
Dot11Radio0                unassigned     NO unset     administratively down    down
Dot11Radio1                unassigned     NO unset     administratively down    down
GigabitEthernet0             unassigned     NO unset     up                    up
GigabitEthernet0.1           unassigned      YES unset     up                    up

Status Down for DB target

Hello, please i need some help.
The status for a DB target is shown as Down in the Enterprise Manager Grid Control console. However, the DB is up and is working normally. What i can see is that user Dbsnmp is Locked(Timed) in dba_users, could this be the problem?. What users are involved with agents and conections to grid control?
How can i refresh the status?
Thanks in advance.

The user that OEM uses is determined by the configuration step with the agent in OEM. So click on the agent in OEM, click the radio button for the db, click configure. Give it the dbsnmp userid and credentials.

Wireless AP will not connect and Radios stay down

Hi,
I have recently configured a Wireless AP for our network. It is running flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" .
I have configured the SSID's VLANS, subinterfaces BVI's etc. I have connected it to our switch infrastructure but i cannot seem to connect to it and the Radio interface is staying down.
Wireless AP Config:
dot11 ssid IMC-Wireless-Data
   vlan 10
   authentication open
   authentication network-eap AUTHVPN
dot11 ssid IMC-Wireless-Voice
   vlan 14
   authentication open
   authentication network-eap AUTHVPN
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
antenna gain 0
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.10
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface GigabitEthernet0
description IMC-Wireless-Data
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.10
description IMC-Wireless-Data
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface GigabitEthernet0.14
description IMC-Wireless-Voice
encapsulation dot1Q 14
no ip route-cache
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
interface BVI1
description IMC-Wireless-Data
no ip address
no ip route-cache
interface BVI10
description IMC-Wireless-Data
ip address 10.10.0.245 255.255.255.0
no ip route-cache
interface BVI14
description IMC-Wireless-Voice
ip address 10.10.14.251 255.255.255.0
no ip route-cache
ip default-gateway 10.10.0.254
SwitchPort Config:
================
interface GigabitEthernet0/2
description IMC-SYD-AP01
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,14
switchport mode trunk
mls qos trust dscp
no mdix auto
spanning-tree portfast
Core Switch Vlan configuration:
interface Vlan10
description IMC-Switch1 - Data VLAN
ip address 10.10.0.252 255.255.255.0
standby 10 ip 10.10.0.254
standby 10 priority 110
standby 10 preempt
end
interface Vlan14
description IMC-Wireless-Voice
ip address 10.10.14.252 255.255.255.0
standby 14 ip 10.10.14.254
standby 14 priority 110
standby 14 preempt
The Logs in the AP come up as :
000022: *Mar 1 11:15:05.211 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
000023: *Mar 1 11:15:05.212 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
If anyone has any idea why this is an issue it would be greatly appreciated.
Thanks

Hi,
Pleas do the below changes..
en
conf t
int dot11 1
ssid IMC-Wireless-Data
ssid IMC-Wireless-Voice
no shut
end
en
conf t
int dot11 1.10
encap dot1q native 10
bridge-group 1
end
en
conf t
int gig 0.10
encap dot1q native 10
bridge-group 1
end
On the Switch
===========
interface GigabitEthernet0/2
description IMC-SYD-AP01
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,14
switchport trunk native vlan 10
switchport mode trunk
mls qos trust dscp
no mdix auto
spanning-tree portfast
lemme know if this helps and please dont forget to rate the usefull posts!!
Regards
Surendra

Single Sign-On:orasso Status Down After Enabling SSL

The status of Single Sign-On:orasso is listed as down in Enterprise Manager after enabling SSL. The same problem existed in with the Portal component, but this was fixed by adding a certificate to the certdb.txt file and by changing some URLs in the targets.xml file.
Does anyone know how to correct this issue with Enterprise Manager? It has no effect on the behavior of our application, but it is causing problems with administration because some people use the Enterprise Manager console to monintor the state of our environment.

Hi,
Did U try this the following steps;
When the configuration is finished, take the following steps:
1.
In the Application Server Control Console Confirmation page, click OK. The Application Server Home page appears.
2.
If you did not have an OC4J_SECURITY instance before, you will have one now. The OC4J_SECURITY instance will have a status of Down. You will also have a Single Sign-On:orasso instance with a status of Down. Select the check box next to OC4J_SECURITY and click Start.
Note: You cannot start the Single Sign-On:orasso instance. This feature is started and stopped when you start and stop HTTP_Server and OC4J_SECURITY.
3.
When the operation completes, verify that OC4J_SECURITY has a status of Up.
Note: The Single Sign-On:orasso status may be displayed as Down. This is normal. The status should be updated approximately five minutes after configuration.
4.
Select HTTP_Server and click Restart.
5.
Verify that you can access OracleAS Single Sign-On at the following URL:
http://hostname.domain:port/pls/orasso
In the URL, hostname.domain is the host on which OracleAS Single Sign-On is installed and port is the Infrastructure HTTP Server port.
You can log in as orcladmin with the orcladmin password.
Also try to check Oracle Application Server Single Sign-On Administrator's Guide
Hear from U & regards,
Hamdy

1522 Radio status down

Similar Messages

Maybe you are looking for