1600 Series Router & WIC-1ADSL

I have some 1600 series routers and was hoping to use them for my Broadband connection.
Is this WIC compatable with the 1600 series router?
What is the required IoS if this is posible?
Thanks Ian

Ganesh,Thank you for the response, however, that article is for the WIC-1DSU-T1 as far as I can see.I was wanting information regarding the WIC-1ADSL. which does not appear to be recognised in my 1603R routers.Thanks Ian
Ian,
The ADSL WAN interface cards (WICs) supported on the Cisco 1700/2600/3700 series routers are also supported on the Cisco 1800 (modular), 2800, 3800 series Integrated Services Routers (ISRs).
As per the link it start supported only from 1700 series routers ony.
Check out the below link hope that clears out your query !!
http://www.cisco.com/en/US/prod/collateral/routers/ps221/product_data_sheet0900aecd8028aa5a.html
If helpful do rate the valauble post
Ganesh.H

Similar Messages

2821 Router with wic-1ADSL card

I am trying to verify a code that will recognize a WIC-1ADSL card in a 2821. The Cisco Software tool page shows that 12.4.10 IPVOICE code has support for this but the card is not seen on the router. When I try the enterprise version 12.4.9(T1) It does't see that card either but shows a VPN module??
Does anyone know what release will work? I am replacing 2620 routers (12.3.19) that have these cards in them for Disaster Recovery. I need support for ADSL- Asymetric Digital Subscriber Line support.

Important bits below:
boot-start-marker
boot system flash flash:c2800nm-advipservicesk9-mz.124-3b.bin
boot-end-marker
policy-map Child
class class-default
fair-queue
random-detect dscp-based
interface ATM0/0/0
description ADSL Service
bandwidth 399
no ip address
load-interval 30
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
vbr-nrt 512 399 3392
encapsulation aal5mux ppp dialer
dialer pool-member 1
service-policy output Child
interface Dialer0
description PPP Session
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname xx
ppp chap password xx

Configuring PPPoE on 2801 with WIC-1ADSl

Hello All!
I try to configure 2801 with WIC-1ADSl
part of my config is:
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/55
encapsulation aal5mux ppp dialer
pppoe-client dial-pool-number 1
interface Dialer1
ip address negotiated
ip mtu 1492
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxx
ppp chap password 0 xxx
ppp pap sent-username xxx password 0 xxx
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
show int dialer
but in this configuration i cann't connect to ISP (and recive ip address)
show int Dialer 1
Dialer1 is up, line protocol is up (spoofing)
Bound to:
Virtual-Access2 is up, line protocol is down
yourname#debug dialer packets
Dial on demand packets debugging is on
yourname#ping 195.161.136.2
Sending 5, 100-byte ICMP Echos to 195.161.136.2, timeout is 2 seconds:
*Mar 15 12:37:33.523: Di1 DDR: ip (s=192.168.0.230, d=195.161.136.2), 100 bytes,
outgoing interesting (ip PERMIT)
*Mar 15 12:37:33.523: Di1 DDR: Cannot place call, no dialer string set.
*Mar 15 12:37:35.523: Di1 DDR: ip (s=192.168.0.230, d=195.161.136.2), 100 bytes,
outgoing interesting (ip PERMIT)
Can anybody help me to correct problem?
Thank you very much

Tnank you very much!!!
the first part of my task is solved...
now my config is
yourname#show run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
ip domain name yourdomain.com
vpdn enable
vpdn ip udp ignore checksum
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 192.168.0.230 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
duplex auto
speed auto
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0/1/0.1 point-to-point
pvc 0/55
oam-pvc manage
pppoe-client dial-pool-number 1
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname xxx
ppp chap password 0 xxx
ppp pap sent-username xxx password 0 xxx
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip nat inside source list 1 interface Dialer0 overload
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
But I need to configure second chanel with PPPoEoA (ethernet over ATM or encapsulation MAC or Enet encap)encapsulation for access to inside SP network (172.16.x.x etc.)
How I can do this?

2811 w/ WIC-1ADSL-I-DG PPPoA issue

Hello:
I have been trying to test our new office gear prior to move, specifically the DSL WIC card.
It seems I have all the config correct but I fail to negotiate link and I am not getting much info from a debug standpoint leading me to believe: -1- PPP isn't quite set up correctly -2- the WIC is possibly bad.
Would it be possible for someone to review my config since I can find nothing on the web that serves as a decent example of using this WIC card with Qwest?
DETAILS:
Info pulled from my old Actiontec modem for testing purposes:
VPI/VCI = 0/32
DSL Mode = MMODE
DSL Negotiated Mode = T1.413
Up/down = 7168/896
ATM QoS class = UBR
The connection is doing PPPoA, evidently it is using PAP per my ISP (qwest does the local loop, my own ISP the VC termination and routing)
Cisco 2811 and WIC setup:
interface ATM0/1/0
description QWEST DSL - circuit id:
no ip address
no ip mroute-cache
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
dsl enable-training-log
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
ppp authentication pap
ppp pap sent-username <username_goes_here> password 0 <passwd_goes_here>
Additionally, it would be helpful if you provided what all the 'Modem States' are. For example, Modem state = 0x8 is in many docs but you don't say anything about 0x3. Its helpful to know all the codes for Modem state if your going to recommend doing debugs of atm events for troubleshooting. Hence, the post to the forum. I can't get link and everything appears to be set up properly.
Thanks for the insight/answers.

No, I am afraid we don't do ADSL over ISDN. My boss ordered the equipment and I think the reseller wasn't too bright.
So would I be correct that I am going to have to have a WIC-1ADSL or a HWIC-1ADSL?
I see that this ADSL over ISDN card we have currently does support T1.413, but given I can't get link I am guessing that is only T1.413 when over ISDN so I have to use one of the other types of WICs listed above if this is over POTS.
If someone from Cisco or otherwise can confirm that would be great so I can go ahead and get the right card shipped to us ASAP.
Thanks for the assist,
-Jeff
Thanks for pointing that out. I suspected it might be the issue but have not ordered or touched many DSL WICs in my day, only the bigger chassis's that terminate the traffic on the provider end.

Cisco 2600 series router and cable modems

Hi everyone, I am just about to get started preparing for my CCNA... I am looking to pick up some used Cisco 2600 series routers to set up a home lab. I am wondering if it is possible to connect a cable modem directly to a 2600 series router? If so, do I need a certain type of WIC? I want to go from my cable modem, to a router, to my switch. Thanks in advance!

Hi,
Yes you can, using the Ethernet port on the cable modem, you can connect the cable modem to the router 2600, and the 2600 comes with builtin ethernet or fastethernet (according to your platform).
HTH,
Mohammed Mahmoud.

WIC-1ADSL Won't No Shut in 1751V

Installed a new WIC-1ADSL in my 1751V yesterday. It sees the card fine, but I cannot get the IF to talk to the line. SO, I do a debug and get the following:
01:44:29: DSL: No response on write to 0x0
01:44:29: DSL(ATM0): Could not download ASW_init_3_8_131.bin
01:44:41: DSL(ATM0): No response from ASW_init_3_8_131.bin
01:44:41: DSL(ATM0): Unexpected response 0x0 to ASW_init_3_8_131.bin
I am not familiar with this error, nor could I find any indications, other than that a
failure to come up appears to point to an error in framing configuration.
Would you be kind enough to give me some potential pointers on how to best deal with this error? Is the ASW_init a file that would work if I load a new IOS in the machine, and if not, where would it be drawn from?

Homeland#show config
Using 1630 out of 29688 bytes, uncompressed size = 2738 bytes
Uncompressed configuration from 1630 bytes to 2738 bytes
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
service compress-config
hostname Homeland
boot system flash
logging buffered 8012 errors
logging rate-limit console 100 except errors
enable secret 5
enable password 7
memory-size iomem 25
clock timezone CST -5
ip subnet-zero
no ip routing
interface ATM0
no ip address
no ip route-cache
no ip mroute-cache
no atm ilmi-keepalive
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
interface FastEthernet0
ip address 10.10.10.3 255.255.255.0
no ip route-cache
no ip mroute-cache
speed auto
full-duplex
interface Virtual-Template1
no ip address
interface Dialer1
ip address 255.255.252.0
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname
ppp chap password 7
ppp pap sent-username password 7
ip nat translation timeout never
ip nat translation tcp-timeout 345600
ip nat translation udp-timeout 345600
ip nat translation finrst-timeout 345600
ip nat translation dns-timeout 345600
ip nat inside source list 102 interface Dialer1 overload
ip classless
ip route profile
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
snmp-server community public RO
snmp-server enable traps tty
call rsvp-sync
dial-peer cor custom
banner motd ^C
Welcome to HOMELAND router.
^C
line con 0
line aux 0
line vty 0 4
password 7
login
no scheduler allocate
end
Homeland#

WIC 1ADSL configuration

Hi everybody,
we bought a used Cisco 1841 router with a WIC 1ADSL module and I am asked to configure it so that we can connect to Internet using our ADSL phone line.
Actually, I started via commands with some configurations found on the internet but it is not working.
I wanted to try via SDM interface, but could not launch and I don't know why.
Please anyone who deals with such a configuration or anybody who well knows about that kind of configuration will be very welcome.
Thank you a lot
NB: Informations got from my Broadband operator are:
login: MY_LOGIN
password: MY_PASSWORD
We got our LAN's individual IP address dynamically from our operator using its given setup box.
and the ranges are:
reserved: 192.168.1.1 to 192.168.1.9
usable: 192.168.1.10 to 192.168.1.100
I hope the above informations will help.
Thank you again.

Hi,
I used the configuration provided by the link but still doesn't work.
Also I can't run these two commands:
ping atm interface atm0 8 35 end-loopback
            GT_Internet_Router#ping atm interface atm0/0/0 8 35 end-loopback
            Translating "interface"
                                   ^
            % Invalid input detected at '^' marker.
ping atm interface atm0 8 35 seg
            GT_Internet_Router#ping atm interface atm0 8 35 seg
            Translating "atm"
                                ^
           % Invalid input detected at '^' marker.
Below is the capture of "debug" commands
         GT_Internet_Router#debug ppp negotiation
         PPP protocol negotiation debugging is on
         GT_Internet_Router#debug ppp authentication
         PPP authentication debugging is on
Please find below the running configuration:
GT_Internet_Router#sh run
Building configuration...
Current configuration : 1646 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname GT_Internet_Router
boot-start-marker
boot-end-marker
enable secret 5 XXXXXXXXXXXXXXXX
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.9
ip dhcp pool LAN
   import all
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   domain-name wr
ip ips po max-events 100
no ip domain lookup
no ftp-server write-enable
no crypto isakmp ccm
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface ATM0/0/0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/32
pppoe-client dial-pool-number 1
interface Dialer0
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp chap hostname MY_LOGIN
ppp chap password 0 MY_PASSWORD
ppp pap sent-username MY_LOGIN password 0 MY_PASSWORD
ppp ipcp dns request accept
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip http server
no ip http secure-server
ip nat inside source list NAT interface Dialer0 overload
ip access-list standard NAT
permit 192.168.1.0 0.0.0.255
control-plane
line con 0
password xxxxxxxxx
login
line aux 0
line vty 0 4
password xxxxxxxxx
login
end
Note: I can't set "vlan interface" on my router
       GT_Internet_Router(config)#interface vlan 1
                                                                     ^
      % Invalid input detected at '^' marker.
so I configured Fa0/1 instead of Vlan 1 for Telnet purpose.
Is there any problem ??
Also I want you to check the atm interface
GT_Internet_Router#sh interface atm0/0/0
ATM0/0/0 is administratively down, line protocol is down
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 800 Kbit, DLY 640 usec,
     reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
23 maximum active VCs, 256 VCs per VP, 0 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
PS: I attached the sample of my network diagram

DSL test lab w/ WIC-1ADSL

Hi folks,
I regularly configure Cisco 800-series routers for field deployment, and I'd love to be able to run through some simulations on the 8x7 ADSL series (837 and 877) in my test lab. I also have a few WIC-1ADSL modules for my 2600/2800 routers.
I know that you can do back-to-back configurations with GHDSL wics, but it doesn't seem to be possible with the internal ADSL modems on the 800's and/or the WIC-1ADSL's.
Can someone please point me in the right direction? I'm looking for the easiest & cheapest way to connect two 8x7's to each other via the ADSL (RJ-11) port, and/or to a WIC-1ADSL.
I'm not necessarily interested in recreating/simulating an entire service-provider infrastructure (yet ;-), my initial goal is just straight connectivity. I'm /not/ familiar with ATM switch or DSLAM specs or configuration, but I'm willing to learn, however I can't spend days and days bringing myself up to speed. Again, getting the connectivity between the CPE devices is primary; the guts of DSL and any required jury-rigging are secondary.
Thanks!

The Cisco 850 series and Cisco 870 series routers support the dial backup function, which allows a user to connect an analog modem to the console port as a backup link to the WAN port in case the ADSL service goes down. Refer URL http://cisco.com/en/US/products/hw/routers/ps380/products_installation_guide_chapter09186a0080471067.html#wp1055766

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

2900 Series Router - Over 700 failed login attempts - How do I find the source IP?

There is a 2900 series router Version 15.0(1)M1, in our company, recently the logs show that there were over 700 failed login attempts to try and gain privelege level 15 access. Is there a way to see the source IP from the host that is attempting the logins?

There is a 2900 series router Version 15.0(1)M1, in our company, recently the logs show that there were over 700 failed login attempts to try and gain privelege level 15 access. Is there a way to see the source IP from the host that is attempting the logins?

I can no longer use the driver for my PSC 1600 Series as of two days ago. The message tells me that the software is not available to update! Has anyone else encountered this. I have OS 10.73 and a MacBookPro

As of two days ago, the ability to print from my MacBookPro to the PSC 1600 Series vanished, indicating they do not have new software ready. I have tried HP and Apple but have not received any help. Can anyone help me to find whatever software that was either lost or not updated. My iMac did have an HP update.

Latest drivers for HP:
http://support.apple.com/kb/DL907?viewlocale=en_US&locale=en_US

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

DHCP Option 60: Go HERE.

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

Setting up a dsl as failover on 2600 series router

I need to setup a failover line. the primary line is a T1 which is connected to serial interface. the secondary line is install to the FE0/1 of a 2600 series router. when i configure the nat pool IPOOL i get a error message saying that dynamic maping in use i need to have a sample config to complete this

Hii,
the msg comes up in there at nat sessions moving on...so u need to clear the ip translations and try executing the command.. if still msg crops.then u might hv to shut the local inside nat interface for a while ..
pls do rate the post.

1600 series Access Point

i want to know 1600 series Access Point support the below or not :-
1)Support up 64 Users
2)VPN pass-through support
3)Wireless Distribution System
4)Wired Equivalent Privacy (WEP) 64-bit, 128-bit encryption

Hi Peter,
will you use this AP as standalone or with Controller ?
1. Normally, the AP is a shared medium and acts as a wireless hub, the performance of each user decreases as the number of users increases on an individual AP. Ideally,as rule of thumb not more than 25 clients should associate with the AP because the throughput of the AP is reduced with each client that associates to the AP.
2. VPN connection will work with this AP.
3. WDS supported.
4. yes, It supports.
Regards
Don't forget to rate helpful posts

1600 Series Router & WIC-1ADSL

Similar Messages

Maybe you are looking for