1602R & new firewall not resolving ARP table

We're trying to install a new Wathguard Firebox Edge and when we replace our old Firebox SOHO, and login to the 1602R, "show arp" has question marks on the MAC address next to the IP of the Edge firewall. We've tried rebooting the router and running "clear arp" and that doesn't work. I suppose we have to manually set the ARP address but I wanted to make sure I have the correct syntax.
Any ideas why a reboot doesn't clear the ARP cache?

Your router is defaulted to use an ip proxy-arp. To disable this please issue the command no ip proxy-arp under global config
of the router.
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094adb.shtml

Similar Messages

Sometimes Local Address not in ARP table and Ping fails (network problem?)

I see something like this on our network a couple of times a week.
The same replies have been received from different hosts.
ping fails
local subnet machine is not in arp table
ping fails
local subnet machine is not in arp table
traceroute may or maynot succeed
If traceroute succeeds an entry is in the arp table
if traceroute fails no entry will be in the arp table.
A netstat -s, ont the local host, doesn't show any thing strange except that udpNoPorts=10844982 (Unfortunately I don't know what udpNoPorts is)
The remote host IS UP.
Does anyone have an idea as to why this is happening?
Can our 100mb network, which is not that busy, be loosing that many ICMP or ARP messages?
This is a problem because I'm the guy getting paged if a system is down.
Local host is Solaris 7 on same subnet at IP 168.173.8.8
Remote hosts are usually NT boxes.
/usr/sbin/ping -svR stpaul_web2 56 3
----stpaul_web2.agribank.com PING Statistics----
3 packets transmitted, 0 packets received, 100% packet loss
/usr/sbin/arp stpaul_web2
stpaul_web2 (168.173.8.143) -- no entry
/usr/sbin/ping -svR stpaul_web2 56 3
----stpaul_web2.agribank.com PING Statistics----
3 packets transmitted, 0 packets received, 100% packet loss
/usr/sbin/arp stpaul_web2
stpaul_web2 (168.173.8.143) -- no entry
/usr/sbin/traceroute stpaul_web2
1 stpaul_web2.AGRIBANK.COM (168.173.8.143) 2995.868 ms 0.231 ms 0.211 ms
/usr/sbin/arp stpaul_web2
stpaul_web2 (168.173.8.143) at 0:1:2:cc:a3:51
Any help is greatly appreciated.
Ks

Hi,
I Think you need to do Teaming on the servers.
++ configure etherchannel between switch and the server.
configuring etherchannel b/w 4503 and server:
================================
http://www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a008089a821.shtml
Sample NIC Teaming - HP NICs with Cisco Switches (EtherChannel) :
==============================================
http://support.citrix.com/article/CTX434260
There are several NIC teaming technologies available today from switch vendors. Cisco uses the term “EtherChannel.” Various switch vendors use various terms, and these may or may not provide the same exact functionality. Use of EtherChannel technology requires support from the server hardware vendor, NIC vendor, and Layer-2 switch vendor.
Hope this helps
Cheers
Somu
Rate helpful posts

New field not reflecting in Table maintenance generator

Hi Experts,
I have added a new field in a ztable.I regenerated the table maintenance generator,so that the new field is reflecting in devlopment system , also a TR got created.When i moved this TR to pre-production system new fields are reflecting in the structure of table but not in table maintenance generator.
Please suggest solutions.
Regards,
Niranjan

Hi Experts ,
I have gone through the steps which is mentioned.But still issue is pending,the changes in TR are not reflecting in pre prod.
Error after moving the TR with "Definition of a Maintenance and Transport Object".
The current ABAP program "SAPLSVIM" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
The following syntax error occurred in program "SAPLZFGL " in include "LZFGL$03
" in
line 13:
"Field "ZCHAR_FIXED_WIDTH" is unknown. It is neither in one of the spec"
"ified tables nor defined by a "DATA" statement. ."

Gratuitous ARPs do not populate the router ARP Table

Hello,
In order to debug an ARP problem in a Firewall cluster environment, I connected a one-armed router on the public VLAN of the firewall cluster, in order to observe the ARP cache behaviour during a switchover. I configured a loopback interface on this router and a default route to this loopback interface to simulate a real router.
When a switchover occurs between firewall cluster members, the active member sends Gratuitous ARPs for all NATed IP addresses. In my environment, I have 110 NATed addresses configured on the firewall.
By launching a "debug arp" on the one armed router, I clearly see all 110 gratuitous ARPs arriving on the router, but the ARP cache of the router is NOT populated with the 110 entries...
Note : The command is configured on the one armed router :
Router(config)# ip arp gratuitous local
What can be the problem ? Is there any condition for a router to accept Gratuitous ARPs ?
Thank you for any help
Yves

Hi
Gratuitous arp is used when a host wants to inform the switch that the mac-address has changed eg.
You have a cluster which has redundant connections and an IP to mac-address mapping. If the active NIC fails the IP address is moved across to the standby NIC but the standby NIC has a different mac-address. So the cluster sends out a gratuitous arp which informs the switch of the new IP to mac-address mapping.
The reason you might not want to allow gratuitous arp is that you might not want your switch updating it's arp table based on annoucements from devices on the LAN as you could very easily spoof mac-addresses and corrupt the arp cache.
HTH
Jon

On a new setup I get error message "'could not activate this table (3001)''

Hi,
I am busy setting up my new playbook and get an error message on the software update screen: "'could not activate this table (3001)'' please try changing your settings.
What settings am I meant to change?
There is a button for settings and when I press this, the playbook takes me back to the connect to WI-FI screen. The WI-FI screen shows that I am currently connected. When I click on hotspot setup, the screen comes back and says I am already connected to the internet.
Can anybody please assist me to complete my setup so that I can start using the playbook?
Looking forward to your feedback
Thanks a stax

Or, you can find a local UNsecured hotspot not requiring a login or password. Like a McDonalds.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

ARP table not populating mac address for previously reachable IP address

Router has been online and working fine with one BGP neighbor for almost 2 years and no downtime. 2 weeks ago, added a 2nd BGP peer. Everything worked fine for 2 weeks, then all of a sudden yesterday the 2nd BGP peer is disconnected and does not come back. ISP checks and sees everything looks fine on their end. We cannot even ping each other now.
Upon investigation, the ARP table is not even populating the MAC address for the BGP peer IP anymore (same local subnet). Stays "incomplete" in the table no matter what we do, including clearing arp table, changing IP address, etc.
Plug a laptop directly into the 2nd BGP peer FE port and replicate the IP addressing. Laptop cannot ping Router, but Router CAN ping laptop. Check ARP table, but STILL no mac address assigned and now not even the ARP table showing "incomplete".
Thinking it could be the FE interface, switch to the 2nd FE interface and perform same laptop test, this time with arbitrary IP addressing. Now cannot ping each other, no MAC in ARP table.
End up rebooting the router and lo-and-behold, everything is working normally again. 2nd BGP peer peers up instantly.
I should also mention that the 1st BGP peer worked flawlessly throughout, taking all the Internet load and having no issues throughout.
Also, the FE ports for the 2nd BGP peer are on an HWIC FE card plugged into the router. The 1st BGP peer is plugged into the built-in GE interface. 2901 running: c2900-universalk9-mz.SPA.151-4.M4.bin
Lastly, no router resource issues, no error messages, no logs. Just the BGP peer disconnecting.
I have never, in 20 years working with Cisco routers seen something like this before. This is the most fundamental aspect of IP and Ethernet that was not working.
Has anyone ever seen this behavior before??
Here is the router config (IP's changed):
version 15.1
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service internal
service sequence-numbers
boot-start-marker
boot-end-marker
logging buffered 150000
aaa new-model
aaa authentication login LAUTHEN local
aaa authentication login TAUTHEN local group tacacs+ enable
aaa authorization console
aaa authorization exec LAUTHOR local if-authenticated
aaa authorization exec TAUTHOR local group tacacs+ if-authenticated
aaa session-id common
clock timezone PST -8 0
clock summer-time PDT recurring
no ipv6 cef
no ip source-route
ip cef
no ip domain lookup
multilink bundle-name authenticated
username ubiadmin privilege 15 secret 4 .JbeuWXuZvchrG0OL.5BftFtqrrEyxcnVHn5rIuCnTk
username umitsnoc01 privilege 15 secret 4 cUmoRUjey9O1x.wk9S.kleX.iAAhCwihupr6Z98p6OA
redundancy
ip ssh version 2
track 1 interface GigabitEthernet0/0 line-protocol
class-map match-any AutoQoS-VoIP-RTP-Trust
match access-group name SIP-Media-INBOUND
class-map match-any AutoQoS-VoIP-Control-Trust
match ip dscp cs3
match ip dscp af31
class-map match-any Customer-Voice
match access-group name Customer-VPNs
class-map match-any media
match access-group name SIP-Media
class-map match-any signaling
match access-group name SIP-Signaling
policy-map AutoQoS-Policy-Trust
class AutoQoS-VoIP-RTP-Trust
priority percent 70
class AutoQoS-VoIP-Control-Trust
bandwidth percent 5
class class-default
fair-queue
policy-map queue
class signaling
bandwidth percent 5
class media
priority percent 50
class Customer-Voice
priority percent 40
class class-default
fair-queue
policy-map shape
class class-default
shape average 10000000
service-policy queue
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description BGP Peer 1
ip address 2.2.2.2 255.255.255.252
no ip redirects
ip flow ingress
ip flow egress
duplex auto
speed auto
service-policy output shape
interface GigabitEthernet0/1
description LAN
ip address 1.2.3.4 255.255.255.0
no ip redirects
ip flow ingress
ip flow egress
standby 255 ip 1.2.3.1
standby 255 priority 105
standby 255 preempt
standby 255 mac-address 1a2b.3c4d.5e6f
standby 255 track 1 decrement 10
duplex auto
speed auto
service-policy output AutoQoS-Policy-Trust
interface FastEthernet0/0/0
description BGP Peer 2
ip address 1.1.1.1 255.255.255.252
ip flow ingress
ip flow egress
duplex full
speed 100
service-policy output shape
interface FastEthernet0/0/1
no ip address
shutdown
duplex auto
speed auto
router bgp 7777
bgp router-id 2.2.2.2
bgp log-neighbor-changes
network 1.2.3.0 mask 255.255.255.0
neighbor 1.1.1.2 remote-as 5555
neighbor 1.1.1.2 update-source FastEthernet0/0/0
neighbor 1.1.1.2 prefix-list L3-DEFGW in
neighbor 1.1.1.2 route-map L3-LPREF-IN in
neighbor 2.2.2.1 remote-as 6666
neighbor 2.2.2.1 ebgp-multihop 2
neighbor 2.2.2.1 update-source GigabitEthernet0/0
neighbor 2.2.2.1 send-community
neighbor 2.2.2.1 prefix-list COLO-DEFGW in
neighbor 2.2.2.1 route-map COLO-LPREF-IN in
neighbor 2.2.2.1 route-map COLO-OUT out
ip forward-protocol nd
ip bgp-community new-format
ip as-path access-list 5 permit _5555_
ip as-path access-list 5 deny .*
ip as-path access-list 10 permit ^6666$
no ip http server
no ip http secure-server
ip flow-top-talkers
top 50
sort-by bytes
ip route 0.0.0.0 0.0.0.0 1.1.1.2 254 name L3
ip route 0.0.0.0 0.0.0.0 2.2.2.1 255 name COLO1
ip route 10.0.0.0 255.0.0.0 10.10.10.10 name FW_OUTSIDE
ip tacacs source-interface GigabitEthernet0/1
ip access-list standard SNMP_SOURCES
permit 12.12.12.0 0.0.0.255
deny any log
ip prefix-list L3-DEFGW seq 5 permit 0.0.0.0/0
ip prefix-list COLO-DEFGW seq 5 permit 0.0.0.0/0
ip prefix-list COLO-LPREF-OUT seq 5 permit 1.2.3.0/24
route-map COLO-LPREF-IN permit 5
match as-path 5
set local-preference 250
route-map COLO-LPREF-IN permit 10
set local-preference 150
route-map COLO-LPREF-IN permit 20
route-map COLO-OUT permit 10
match ip address prefix-list COLO-LPREF-OUT
set as-path prepend 7777 7777 7777
set community 29795:1004
route-map COLO-OUT permit 20
route-map L3-LPREF-IN permit 10
match as-path 10
set local-preference 200
route-map L3-LPREF-IN permit 20
set local-preference 150
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps vrrp
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps ds1
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps license
snmp-server enable traps envmon
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps flash insertion removal
snmp-server enable traps mac-notification
snmp-server enable traps aaa_server
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps memory bufferpeak
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps cpu threshold
snmp-server enable traps rsvp
snmp-server enable traps syslog
snmp-server enable traps vtp
snmp-server enable traps ipsla

When you were checking the ARP table was there an entry for Fast0/0/0?
HTH
Rick

SX20 Is showing up in ARP table but not reachable

Hello,
I'm currently working on an issue at a customer site where two of the video endpoints (both SX20s, one running TC7.3 and one running TC7.2) will work in some switch ports and not work in others. The switches that they are connected to are both 3560s running the same ios version and with the same switchport/vlan configuration. Both switches are connected to a Nexus 5k and this is then connected to our router (2821). The switches are managed by the local site IT while I manage the router. All IP's are statically assigned.
On the router I can see the endpoint's MAC address and it shows up in the ARP table correctly but it is not pingable. Our other video systems that are not SX20's work properly when connected to these ports (Tandberg 990MXP, C20 and C40). When we replace the codec with a PC with the same IP/MASK/GW configuration it is pingable. This leads me to believe it's not a networking issue but is an issue with the endpoints themselves. However, they do work properly when they are connected to other ports that have the same configuration.
Has anyone else run into similar issues?
10.222.129.33 = Gateway
10.222.129.34 = SX20 #1 in a working port
10.222.129.37 = SX20 #2 in a non-working port
Router#show arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.222.129.33 - 0016.c7b0.4388 ARPA Vlan34
Internet 10.222.129.34 0 84b8.02cc.c59b ARPA Vlan34
Internet 10.222.129.37 8 84b8.02cc.be58 ARPA Vlan34
Internet 10.222.129.38 0 0050.600c.a09e ARPA Vlan34
Internet 10.222.129.40 0 e4c7.2264.216b ARPA Vlan34
Internet 10.222.129.41 13 0050.6002.43b0 ARPA Vlan34
Internet 10.222.129.43 3 00e0.db05.ba45 ARPA Vlan34
Internet 10.222.129.44 13 0050.6001.f2b5 ARPA Vlan34
Router#ping 10.222.129.37
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.222.129.37, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Router#ping 10.222.129.34
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.222.129.34, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Router#

So you are saying for it to do what i want: shared photo stream to appear in web then i need to upgrade.
Yes
Does that mean i purchase the new software an it's not just an update?
Yes
Your profile indicates your running 10.7.5. For shared Photo Streams you need to be running 10.8.2 or later: The following is from iCloud: Photo Stream FAQ
What do I need to use Photo Stream?
To use Photo Stream, including Shared Photo Streams, you need an iCloud account, compatible devices, and up-to-date software: iPhone, iPad, or iPod touch with iOS 6.0 or later Mac with OS X Mountain Lion v10.8.2 or later and iPhoto 9.4 or Aperture 3.4 or later
So you'll need to upgrade to Mt. Lion.
iPhoto requirements are free updates for iPhoto '11
LN

When the message arrives, the message tone sound that many times. How this problem can be solved? I installed the new version, but the problem is not resolved, the future is to be taken into account in the new version of this?

When the message arrives, the message tone sound that many times. How this problem can be solved? I installed the new version, but the problem is not resolved, the future is to be taken into account in the new version of this?

I'm not sure I understand the question, is the message tone going more then once?
Turn off repeat message alert here:
settings > notifications > messages > repeat alert > never
Some people have found this does not stop the repeat miessage tone,
if you are one of those then I suggest you contact Apple:
http://www.apple.com/feedback/iphone.html
They may not respond, but hopefully will fix in uodate if enough people complain.

Have been here before but still have not resolved a fix for a black screen when I try to access a PDF file...Now I've got a new iPad and need the User Guide which is only available inPDF

Have been here before but still have not resolved a fix for a black screen when I try to access a PDF file using Safari...Now I've got a new iPad and need the User Guide which is only available in PDF and FireFox will not work.

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you.

Host not showing up in ARP table

Hi,
I am having an interesting/weird problem with one of my Catalyst 6509 switches.
The setup is as follows:
HostA - Switch1 - Switch2 - HostB
There is routing in place for HostA to reach HostB and vica versa.
I am testing this using ICMP. There is nothing blocking ICMP traffic on any of the devices.
Problem in question: I can only ping HostB from HostA (or Switch1) if HostB is found in the ARP table of Switch2. Pretty normal you might say since we need Switch2 to route/switch the packet to HostB and that will of course only happen if the ARP table is populated.
But what happens is the following:
I ping from HostA to HostB. It fails. I check Switch2 and I see that HostB is nowhere to be found in its ARP table.
Next I ping HostB from Switch2 (5 packets). First packet fails, last 4 I get a reply. I check and see that now HostB is to be found in the ARP table of Switch2.
Now I ping HostB from HostA and it works fine.
This behaviour is happening for all hosts in the subnet (VLAN) of HostB. I cannot reach them until I ping them from Switch2, after which they're in the ARP table and everything works.
Maybe it something different than the ARP table not being populated all together, but that is for now all I noticed. Does this problem ring a bell with anyone. And is there a fix?
It looks to me like Switch2 is malfunctioning, although I have no idea what is. Furthermore this apears to be working ok for a lot (read: all) of the other VLANS on Switch2.
Anyway. I'd love some help in troubleshooting this one.
kind regards,
Kevin

This goes back to the way switches (or bridges) work. They have to see a frame from an end device to know its MAC address and once they see it they add an entry in their CAM (or MAC) table. The entry basically tells the switch that a specific MAC is reachable via a particular port and this is meant to prevent subsequent flooding of unicast frames. In short an end device needs to send at least one frame for the switch to 'see' it. Another point to remember is that each entry in the CAM table has an age associated with it and if a switch does not see subsequent frames from that host it will age out the entry and start flooding all frames destined to this MAC address until it is learnt again (and learning is done only when the owner of the MAC starts to communicate again).
Kevin,
Can you please explain your topology in a bit more detail? I am looking for information like what is the default gateway of each VLAN, how are the VLANs spread across the two switches, any HSRP configurations and if yes who is the active for what VLAN, routing between switches, etc. This will help us troubleshoot the problem in a more effective manner.

DNS Server does not resolve new generic Top Level Domain names- CNR configuration issue?

Hi all,
I am not sure if this is the correct community to post this question, but I will give it a try. I noticed that the users of my network cannot resolve web sites using new top level domain names, like ".education", ".international", etc. I have an internal DNS server made by Infoblox and a Cisco CNR v6.3.3.1 as an external DNS server. Infoblox uses CNR as its forwarder and CNR uses the root DNS servers for queries.
I would think that CNR was the problem because it is an obsolete product but after speaking with a fellow engineer at another organization where they still use an older version of CNR than mine, they have no problems at all. So now I am thinking it is a setting either on Infoblox, or on CNR I need to change. I can see Infoblox is forwarding the requests to CNR but that's about it. I am not sure if CNR is discarding the request. When I do an nslookup from a PC in my network it does not matter if I set my DNS server to be the Infoblox or the CNR. Neither resolves the URL.
Then again, no matter what I lookup using the CNR as my DNS, I only get a response with the root DNS names and IPs!
Any help is appreciated!

Hi Constantinos,
Have you taken a look at the infoblox community site? We've just reposted your question there and alerted some internal SMEs that should provide a solution soon.
https://community.infoblox.com/forum/ddi/dns-server-does-not-resolve-new-generic-top-level-domain-names-cnr-configuration-issue
Best,
Eric

I want to delimit the date of table v_t7int1 for new sap note uploading

Hi
i want to delimit the date of table v_t7int1 for new sap note uploading. wtihout delimit the date i can't create new note for the year 01.04.2009 to 31.12.9999
Anjali

Hi
When i select the slab code sl10 and press delimit button system is asking the From Date and i want TO DATE and i have to Delimit the date of slab code SL10, SL11,SL12 and SR02 and then i have to create SL13,SL14 and SL15.
Anjali

Issues with Advance Table Add Row New Row not work in some scenarios.

Hi,
Wondering if there's any issue with Advanced Tables where it does not create any rows. I don't know if anyone tried this or not. I have one OA Page with Advanced Table and a button that when clicked open a new OA Page in a POP-UP Window. The pop-up page conatins one textbox where u enter a data and this gets saved in one of the VO's transient attribute. Now on the ase page if you don't click a button to open a pop-up page you can Add New Rows in the Advanced Table by clicking Add Row Button. But as soon as you open a popup window and close it Add New Rows button doesn't work and is not creating any new rows. Basically page stops working. Both the POP-UP and the base page share the same AM but have different controllers.
POP-UP page is a custom page that I open giving the Destination URI value in the button item and target frame _blank.
I even tried creating rows programmatically for Advance Table but this too doesn't work once u open a pop-up. Also I have used pageContext.putTransactionValue in the pop-up page and am checking and removing this in the base page.
Any help is appreciated.
Thanks

anyone

TS2771 I have just fitted a new sreen and lcd to my ipod 4th gen everything is workink, but im having problems with selecting the upperscace and also the back space i have done a full reset and every thing i have tried has not resolved the problem

I have fitted a new screen and lcd to my ipod 4th gen and now I'm unable to select the uppercase on the key board also other key in the lower part of the screen are intermittent, I have now carried out a full reset and this has not resolved the problem, and the latest software is installed apart from this everything else is working can anyone help

Have you restored the iPod to factory defaults/new iPod? If so then you have a hardware problem. Maybe a loose/brken connector or maybe something else.

Hi,I have uploaded an app build for pre release and its still under processing So i uploaded a new build but still the issues is not resolved.Please help...Thanks

Hi,
I have uploaded an app build for pre release and its still under processing So i uploaded a new build but still the issues is not resolved.
Please help...
Thanks

Hi smithin,
Thanks for visiting Apple Support Communities.
It sounds like you've submitted an iOS application to the App Store, which is being processed, but there's an unresolved issue.
For additional help with this situation, Apple Developers can use the contact methods on this page:
https://developer.apple.com/contact/
All the best,
Jeremy

1602R & new firewall not resolving ARP table

Similar Messages

Maybe you are looking for