17" White iMac w/Bootcamp XP won't boot.

I have a 17' white iMac with Leopard and Bootcamp with XP installed, and it was stopped by punching the power button.
Now it won't boot at all. Usually I just get the gray screen that comes up after the chime and a moveable cursor.
Sometimes, if I unplug it for several hours, I can boot and hold the OPTION key and get the two HD-pictures for OSX and XP, but when I get these it will boot into the op sys, but then hangs.
I can boot into TARGET mode and have ordered a 800/400 Firewire cable to try and get stuff off the computer to my 24" 09 iMac. Most of my data is on the Bootcamp Windows partition.
(a) Will reinstalling OSX from DVD destroy Bootcamp partion?
(b) Any way to run OSX (or XP) from DVD so I can access the HD?
(c) Any other tricks or links to things to do?
Thanks.

That "you have viruses" message was a fake, designed to scare you into purchasing the scammer's fake software. Apple has information and instructions for removal:
http://support.apple.com/kb/HT4650
For additional information, see also:
http://www.reedcorner.net/news.php/?p=138
http://www.reedcorner.net/guides/macvirus/
If you do a forum search on Mac Defender, Mac Protector or Apple Security Center (this fake has a lot of diffeent names) you will also find a lot of threads about this.
If you gave these crooks your credit card information, immediately contact your credit card company and report the fraud. I'd further suggest that you request that they put a block on your account and issue a new card number or you may find unauthorized transactions appearing in our account.
I doubt that this caused damage to your Windows boot - I've not seen any reports of this happening - but I can't be certain. Get this fake junk removed and see where things stand.
Regards.

Similar Messages

My 2006 iMac running Snow Leopard won't boot even after erasing and re-installing Snow Leopard (via my MacBookPro), either from the HD or DVD drive. Can't get it to run Hardware Test. Disk Utility says disk OK - files are there. What can I do?

My 2006 iMac running Snow Leopard won't boot even after erasing and re-installing Snow Leopard. I erased and re-installed by putting the iMac in Target Disk mode and usin my MacBookPro as the host. But after numerous attempts I still can't get it to boot either from the HD or DVD drive. I just get the white screen after the wheel stops spinning. I can't get it to run Hardware Test - just get the white screen. If I use Disk Utility via my MBP it says the disk appears OK. All the Snow Leopad files appear to have been installed. What can I do?

Hi-NRG Bwoy wrote:
I erased and re-installed by putting the iMac in Target Disk mode and using my MacBookPro as the host.
Reet the SMC and the PRAM
 Cheat sheet to help diagnose and fix your Mac
Perhaps you installed the wrong version OS X onto the iMac, you can't use the disk from another Mac.
clean the disk.
If it's not working then use this method to create a bootable 10.6 USB from the iMac machine specific 10.6 disk or the 10.6.3 retail disk on your other Mac, use it to boot the iMac with.
http://www.maciverse.com/install-os-x-snow-leopard-from-usb-flash-drive.html
How to erase and install Snow Leopard 10.6

IMac G4 800 17inch won't boot.

Hi,
I posted a topic some months ago about a problem I was experiencing with an old G4 iMac I own. The problem is still not fixed so here's an update of the problem.
Spec;
iMac G4 17inch 768 mb ram, Airport card, OS X 10.2.8
When you turn on the computer all i get is the grey screen with the apple logo. No spinning timer to say its booting up. It stays like this until you turn it off.
What i've tried so far;
All usb devises etc have been disconnected ( only keyboard and mouse left)
Reset the PRAM
Reset the Power management unit
Inserted the installer disk, held down C but still it won't boot to the installer / disk utility options. However the timer wheel appears but nothing happens
Any help would be greatly appreciated. I'm at a lose end as to what to do next!
Thanks

Hi! You've tried most things but try holding the "x" key down at boot and if that doesn't work try the shift key. have you tried the hardware test disc? Tom

IMac G5 Power PC won't boot past the grey apple and pinwheel

After everything froze and having to shut down (holding the power button), it won't boot past the grey apple and pinwheel. After a few seconds, the fans speed up and then nothing else.
*it won't boot into safe mode (holding shift)
*booting to OS on DVD works but then freezes after select language and hit "continue"
*disk utility shows the actual hard drive name but no disk image/partition is listed for me to repair or change
*running the system hardware diagnostic CD returns a list of "passed" for all hardware
I did have the logic board replaced during the extended warranty period a few years back and have not had any issues at all since.
Any thoughts, suggestions, tricks/tips?

Perfect diagnosis. I replaced the HD and reinstalled the OS. Back in business! Thanks!

IMac ate DVD, now won't boot...

Hi,
After using iDVD I had the dreaded "ate the disc" issue, with the typical grinding noise and the lack of ejection. I figured I would play it safe, power down the machine so it wouldn't be reading it, and boot it up again and eject it using the keyboard / mouse button options that are suggested here.
Except it won't boot at all.
I'm stuck on a grey screen, the HD does nothing, and the DVD drive grinds from the instant the power is on.
I have literally no options that I can think of - it just sits and grinds and does nothing, won't boot, won't target disk, won't do anything. None of the hold-buttons-at-start will do anything, because the machine won't get that far. The drive starts grinding before the screen even lights up.
Help!
Message was edited by: productiondesignermatt
Message was edited by: productiondesignermatt

Ok, now it appears to have booted, but the disk is still in there. I'm doing a full Time Machine backup (justincase), but after that... what to do?
I really can't be without this machine for two weeks and it was a custom order so a replacement isn't going to happen.
As someone who works for Apple's biggest UK reseller, am I seriously having to reconsider whether I even want to work there any more - no reflection on my employers, obviously, but this is 3 bad machines I've had from Apple in one year and the return rate I've started seeing on hardware is utterly appalling.
The nosedive in quality after using them for over 8 years is simply astonishing.

Upgraded imac to mavericks, now won't boot, stuck on white screen then reboots in a loop

i have a imac that i upgraded to mavericks, it wont boot up now, sticks on white screen for a while the reboots and sticks again, if i reinstall osx will it delete all my data- i tried to start the new install in recovery mode but it kep saying incorrect username and/or password, but i ts not incorrect and when i hit the forgot password link nothing happens

If you can get it to boot once the first thing you should do is backup all your data using Time Machine or better yet create a Bootable Clone using SuperDuper or Carbon Copy Cloner. What Apple says to do to trouble shoot is in Gray screen appears during startup.
I would also recommend running Apple Hardware Test in Extended Mode, if no errors appear the first time run the test 2-3 more times. Each Extended Mode test will take 30-60 minutes.

IMac turned off suddenly, won't boot from hard drive/CD drive

Hi guys.
Here is what I have:
27" iMac with:
Core i5 2.7
4GB RAM
Mountain Lion
Win7 on Bootcamp
Lion is installed, but I have the Snow Leopard install disc.
The system had just been recently reformatted so there wasn't really much on the computer itself other than an update to Mountain Lion and a Win7 install via Bootcamp. Other than that, nothing was recentlly installed.
What happenes is I was browsing and all of a sudden it completely shut down. No warning, nothing. Completely shuts down.
Okay.. weird... but when I try to load Mac back up, the Apple logo appears and then after a while of supposedly loading, the screen goes to a plain white screen until I force the computer off. Something similar happens when tryin gto boot into Windows: I get to the "Starting Windows" screen but after that everything goes black and I have to shut down manually.
Great. Now I'll just go into recovery and fix all of this right? Wrong. Can't boot into recovery either. Similar end result: white screen.
Last thing I tried is reinstall OS X Snow Leopard. After loading for about 1-2 minutes, the usual white screen appears after trying to boot from the disc.
I am at a loss. I don't think its the hard drive, because the problem occurs even when trying to boot from the disc. My suspicion is the RAM has gone bad. But, before I go the hardware route, is there any suggestions or recommendations anyone could make first?
In advance, I really appreciate anyone who replies and tries to help.
Thanks.

Xmotox,
I had the EXACT problem today. EXACT. Discs wouldn't boot, I did get the application disc to run the AHT but it said all was fine.
I called my buddy who said something about unplugging for a minute then holding power button while plugging the power supply back in. I thought it would be futile since we already did all the SMC reset procedures to no avail, PRAM reset didn't do anything, etc, etc... But what do you know, up pops the disc utility and my iMac is now restoring from time machine. It's not done yet, so I can't say it worked... BUT it's the farthest we got tonight. Could not get disc utility up via CMD-R or OPTION keys... but powering down, unplugging for a minute or so, then holding power button while plugging the power supply back in did the trick. Hope this helps!

Installed the latest Java update today on my older iMac and now it won't boot up at all. 2007 model worked fine this morning, now disk first aid say boot blocks f'ed.

I am using an older mid 2007 imac 24 inch running snow leopard 10.6.8
I normally accept software update recs, and today when installing the security update to java, all went fine till restart, when I got the universal "NO" sign, the circle with the line through it and just spinning gray bars underneath.
Booted from system disks, ran first aid, said the boot block partitions or something like that needed updating but disk appears to be ok. Still not working.
Do you think Alsoft Disk Warrior will fix? I am running off external back up drive now.
Thanks for any help or advice. Apple as usual is as useless as tits on a bull, or a screen door on a submarine, pick your simile...

If your backup's up to date it might be less hassle to erase the internal and clone back from the backup. Don't allow the update next time it appears - you're not the only one having problems it would seem.
Note; the message "updating boot partitions" is a standard message that appears after a repair run. It won't go away and should be ignored.
Provided the message "The volume Macintosh HD Seems to be OK" in green has appeared, your disc fle system is fine.
Message was edited by: noondaywitch

Bootcamp partition won't boot with two OSX installations

Hey,
I have a MacBook Pro running OSX Mavericks (10.9.5) and had installed Windows 8.1 through Bootcamp and everything worked like a charm. I then added a new partition to install the developer preview of OSX Yosemite. Everything worked, I could boot to OSX 10.9.5, OSX 10.10, both recovery partitions and Windows.
Lately, my Mac had some issues that made me booting to 10.9.5 recovery and using disk utility to repair the Mavericks and Yosemite partitions (both were good, interestingly I could not repair the disk permissions, though) and I even clicked on "Repair", as the whole disk was selected and Disk Utility repaired something (I forgot what it was, but I think it changed the MBR).
Now the Windows partition is gone, when I option-Boot and when I try to reboot from OSX to the Windows partition using the "startup disk" option of System Settings, it says
No bootable device --- insert boot disk and press any key
I want to be able to boot Windows again (and my OSX partitions) and would love to be able to do so, even when I choose to delete the Yosemite partition once it's out of beta so that I can update Mavericks. I tried using this guide:
Repairing Boot Camp after creating new partition
My problem is that it says that the Windows partition should be number 5 on /dev/disk0. In my case, the described partition is number 6.
Can I simply replace the number and it should still work or will it break something that the Windows partition is not at the place it normally is?
Thanks in advance

Well, I just tried it and it didn't work. I still don't see the Bootcamp partition when I option-boot and when I try starting Windows via Startup Disk settings, the screen just turns black after a while and then a white blinking horizontal cursor appears (not even the "No bootable device" error any longer).
Any help would be appreciated.

IMac G4 700 MHz won't boot

Hey there all,
A cousin got an old iMac G4/700MHz running Mac OS 10.4.x. It worked fine when she bought it but, now it won't finish booting. I've turned it on and it won't get beyond the gray screen with the little gear cycling. I zapped the P-RAM and still nothing. What else might be the issue? It's a Mac for her elementary school-age kids, for school work(research) and web-surfing to kid-friendly sites. There are no external devices connected to it not even speakers, just a keyboard and mouse.
TIA for any assistance or suggestions.

Try starting in Safe Mode, with the Shift key depressed during startup until you either get a desktop or a message saying that you are in Safe mode. If this gets you a desktop, don't use the computer just yet. Do a regular restart. If you still get a desktop, it's probably OK. If not, post back.
If the computer has been stored off wall power for any time, or unplugged from the wall every night, the internal logic board battery is likely dead. That can cause startup issues. However, on this model iMac, it takes the same effort to get to the battery as it does to replace the hard drive. Although neither is considered a "user-serviceable" part, should you feel comfortable with dealing with computer innards, google for "iMac G4 takeapart" to find instructions. Illustrated instructions are out there and they may help you assess your comfort level with home repair.

Is there hope an iMac Bondi Blue that won't boot?

I have an original Bondi Blue iMac 233MHz, Rev. A. I upgraded the RAM to 128MB about 2 years ago, and it has been operating on 10.2. It had been working perfectly until last week. When the power button is pressed to start the computer, the startup chime is heard, the power button light changes from amber to green, the gray screen comes up with the black Apple icon, and eventually the little gear-shaped thing starts spinning...and that's as far as it goes. I hear it grinding away from time to time, but it never goes beyond that point. The only way to shut down is to unplug the machine.
I've reset the PRAM, tried starting with extensions disabled, checked the battery, and tried to boot from a start-up disk, but nothing has made any difference. I wouldn't mind if the computer has given up, but there are some things on it that I'd really like to retrieve, and I can't even use it as a target disk with a Firewire. It doesn't have a Firewire port, and it won't start up in Target mode.
Is this the end of the line for Old Blue? Could the 128MB RAM card that I installed be faulty and causing the problem? Any other ideas?
iMac 233MHz Mac OS X (10.2.x) Original Bondi Blue, Rev. A

Thanks so much for taking the time to respond to my question. Yes, I had read that article and done each of the steps recommended, but have had no luck. I'll look into your suggestion of removing the hard drive and trying it a Firewire or USB enclosure. I don't have either one as an external device, so will have to determine first whether or not this would be cost effective.
iMac 233MHz Mac OS X (10.2.x) Original Bondi Blue, Rev. A

Bootcamp mac won't boot from usb

Hi
I just created a bootable usb with bootcamp. I am trying to run windows 7an am currently running Mavericks . I created the usb stick on boot camp no problem. But when I try to boot from it it freezes. I think the usb drives loose power because the caps lock button won't turn green if i push it. The usb stick light doesn't even try to flash it is just dead. I don't even have an idea what might be wrong.
Thank you any help is appreciated.

Do not use a USB3 flash drive. Only USB2 flash drives are supported by Windows installers. Depending on whether your Mac came with a built-in Optical drive or not, you may also need a physical DVD.
Please see How to install Windows using Boot Camp - Apple Support and Boot Camp 5.1: Frequently asked questions - Apple Support.

1st gen iMac G5 Crashes and Won't Boot Up

To whom it may concern :
I've been having problems with my 20" iMac G5.
It frequently freezes and a message that says I have to restart my computer by pressing the power button for a few seconds appears.
At first, after I've done as the message said, my computer booted up successfully and after startup a message that says "Mac OS X quit unexpectedly" appeared, although when I pressed Report it did nothing.
For the past few days, the same as above occurs except when I try to boot up my system it starts booting up and freezes on a black screen while the computer backlight is on.
If I'll leave it on in this state for a minute or two, the fans will begin spinning at maximum speed (I believe so due to the great noise and mild dust they will produce when doing this).
I should state that it freezes randomly and not after a specific action: when I multi task, when I return to the computer after being idle (screen saver or the monitor was off) or even when no programs are running.
Does anyone know what's wrong with my Mac ?
Please Help !!
- Ben
1st gen 20" iMac G5 (1.8 GHz) Mac OS X (10.4.9)

To The Apple Discussion Boards!
Except for your keyboard & mouse, disconnect all devices from your computer & repair disk & permissions from your Tiger DVD.
Repairing permissions from the Tiger DVD
Boot up from your Tiger Install DVD while holding down the "c" key.
Select the language you wish to use, and then choose "Disk Utility" from the menu bar.
Your HD should appear in a panel on the left hand side of the window which opens. Select it and then click on the "repair disk" button in the right hand section of the window.
If Disk First aid is able to complete the repair now click on the "Repair permissions" button.
Once this process has been completed restart your computer.
http://docs.info.apple.com/article.html?artnum=25751 About Disk Utility's Repair Disk Permissions feature

Imac G4 flat panel won;t boot

screen won't come on when I start, instead of the familiar start chime I get two beeps when I attempt to start.
Tried to start in safe mode, reset pram and I still get a black screen and two beeps with the power light indicator blinking.
OSX 10.4.11, wireless keyboard
Message was edited by: Gary Tate
Message was edited by: Gary Tate

well I went and removed the 256 ram in the bottom and the computer booted sucessfully.
So from this can I say it's is either the ram or the bank on the logic board holding the user installed ram is bad (requiring a new logic board?)
Will have to find a good set of ram somewhere to install and see if it boots, thus showing the ram I took out is bad.....????
Thanks for the help

Bootcamp Win7 - won't boot from Windows partition or even from the Win7 install DVD

Late 2011 Mac Mini / Lion / Win 7 64-bit Home Premium.
Incumbent Windows partition has happily run for heavy gaming (World of Warcraft) for some eight months. Now it stops on boot-up before the Windows logo is displayed, with a very dark blue blank screen. Attempts to boot from the Windows Install DVD yield the same result, portending that there is more than a corrupt MBR at work here. I have reset PRAM and SMC, just for good measure. There have been no recent changes to hardware / peripherals.
Rebuilding the Windows partition with Bootcamp stops at same Dark Blue Screen of Death. Will start Windows sometimes from first switch-on / dead cold Mini, but then not again in the same day. OS X Lion mode runs perfectly, booting up as usual with no quirks or delays.
Hardware? Seems unlikely, except for that suspicion of starting from the dead-cold start.

Do not use a USB3 flash drive. Only USB2 flash drives are supported by Windows installers. Depending on whether your Mac came with a built-in Optical drive or not, you may also need a physical DVD.
Please see How to install Windows using Boot Camp - Apple Support and Boot Camp 5.1: Frequently asked questions - Apple Support.

17" White iMac w/Bootcamp XP won't boot.

Similar Messages

Maybe you are looking for