1760 and VIC2 2FXS

What IOS will I need to configure analogue voice ports on a 1760 router? I've tried following the IOS selector but most of the releases it suggests are deferred.

According to the following link, the VIC-2FXS card is supported in all versions of IOS for the 1760 with a voice feature set.
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094fac.shtml
Hope this helps. If so, please rate the post.
Brandon

Similar Messages

  • Vic2 - 2FXS Card in 2801 and modem / fax usage

    Hi,
    I have a Cisco 2801 running c2801-advipservicesk9-mz.124-9.T.bin
    It has 2 VIC2-2BRI-NT/TE cards, 1 VIC2-2FXS. And a PVDM2-8 and a PVDM2-16 as DSP's.
    I am trying to get a modem working on a FXS port, but one way or the other it's just not comming together.
    I do have a propper PSTN line when I use an analogue phone, but when I try to hook up a modem nothing or sometimes a crappy 2k4 connection.
    What am I missing here, I thought by putting in enough DSP's in the router and a FXS card and BRI cards this should work.
    Nothing fancy configured on the voice ports (first 4 are BRI last 2 FXS)
    voice-port 0/0/0
    compand-type a-law
    cptone CH
    voice-port 0/0/1
    compand-type a-law
    cptone CH
    voice-port 0/1/0
    compand-type a-law
    cptone CH
    voice-port 0/1/1
    compand-type a-law
    cptone CH
    voice-port 0/2/0
    cptone CH
    voice-port 0/2/1
    cptone CH
    Can anyone tell me what to do to get a modem working propperly on this FXS ports ?

    You may want to try adding this command:
    voice service voip
    modem passthrough nse codec g711alaw

  • Testing VIC2-2FX S and VIC2-2FXO cards

    I want to setup two 2611XM routers with a
    NM-HD-2VE ( 3 DSP), VIC2-2FXS, VIC2-2FXO cards.
    Can I connect the FXS to the FXO ?
    Do I need to have telephones with RJ11 Straight through cables connected to the ports of the VIC's.
    Could you point me to somewhere where this scenario is addressed. ( Voice certification test lab diagrams...)
    Thank you,
    Tom

    Dear Experts
    This is going to be my first implimentation of the Voice network and is turning out to be a nightmare.i have reffered all the configuration mannuals , books and videos but still not able to make calls across the MPLS network.Need help urgently to solve the issue.
    Here is the senario
    PSTN>>>FXO(Cisco2905)>>>>>MPLS Cloud<<<<<<<(Cisco2905)FXS>>>>>>>>Phone
    here is the configuration i have done
    <<<<<<<<<>>>>>>>>
    voice-port 0/1/0
    voice-port 0/1/1
    connection plar 2201
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    dial-peer voice 998 voip
    destination-pattern 22..
    session target ipv4:192.168.220.1
    dtmf-relay cisco-rtp
    dial-peer voice 100 pots
    destination-pattern 9............
    port 0/1/1
    on
    <<<<<<<<>>>>>>.
    voice-port 0/0/0
    cptone ID
    voice-port 0/0/1
    cptone ID
    mgcp profile default
    dial-peer voice 220 pots
    destination-pattern 2201
    port 0/0/0
    forward-digits all
    dial-peer voice 221 pots
    destination-pattern 2202
    port 0/0/1
    forward-digits all
    dial-peer voice 110 voip
    destination-pattern 9T
    session target ipv4:192.168.0.1
    dtmf-relay cisco-rtp
    =====================================
    Early response is much appriciated
    REGARDS
    SANDEEP

  • ISR 2811 with VIC2-2FXS

    hi,
    We have deployed cisco 2811 router in our network and had installed vic2-2fxs card in one of the HWIC slot.We need to configure fxs card for voip to make a call to branch office and have the following ios c2800nm-ipvoicek9-mz.124-17.bin .The problem we are facing is the router detect vic card under show version command but when show running-config command been given it doesn't display voice-port information to configure the same.We have attached the show tech-support o/p.any suggestion welcomed.

    Hi Bhavesh,
    It Looks like you do not have any DSP resources.You will need something like a PVDM2-8 card on the motherboard to provide DSP resources to the FXS card. Without DSP resources you cannot configure the FXS :)
    Hope this helps!
    Rob

  • VIC2-2FXS at Cisco 2811 ISR, is NM-HDV2 needed?

    Hello,
    I have a Cisco 2811 router that is configured as CUCME and working OK. So I need to connect a fax machine so I decided to take FXS card, but I don't know if I need to find NM-HDV2 to get VIC2-2FXS working on 2811, or it works at any of HWIC slots... I have FXO (VIC2-4FXO) working w/o any network module (installed at HWIC slot), so do I need such for FXS?
    P.S.: I have PVDM2-8 installed in the router, will it be enough?
    Thank you.

    The NM is not needed.
    The PVDM that you have is enough.

  • VIC2-2FXS problems

    Hi,
    we have ISR 2801 router with 2xVIC2-2BRI-NT/TE, 1xVIC2-2FXS and PVDM2-8, IOS ver.c2801-spservicesk9-mz.124-9.T7.bin. We can see ISDN BRI ports but cannot see FXS ports.
    Any help?
    here some outputs from router:
    sh ver.
    Cisco 2801 (revision 7.0) with 235520K/26624K bytes of memory.
    Processor board ID FCZ121412Q8
    2 FastEthernet interfaces
    4 ISDN Basic Rate interfaces
    2 Voice FXS interfaces
    1 DSP, 4 Voice resources
    DRAM configuration is 64 bits wide with parity disabled.
    191K bytes of NVRAM.
    126976K bytes of ATA CompactFlash (Read/Write)
    sh invent
    NAME: "chassis", DESCR: "2801 chassis"
    PID: CISCO2801 , VID: V04 , SN: FCZ121412Q8
    NAME: "VIC 0", DESCR: "2nd generation two port BRI voice interface daughtercard"
    PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QZW
    NAME: "WIC/VIC/HWIC 1", DESCR: "2nd generation two port BRI voice interface daughtercard"
    PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QL0
    NAME: "WIC/VIC 2", DESCR: "2nd generation two port FXS voice interface daughtercard"
    PID: VIC2-2FXS , VID: V01 , SN: FOC12121ZWM
    NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
    PID: PVDM2-8 , VID: V01 , SN: FOC12085ZJS
    sh voice port summ
    IN OUT
    PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
    ============== == ============ ===== ==== ======== ======== ==
    0/0/0 1 bri-voice up dorm none none y
    0/0/0 2 bri-voice up dorm none none y
    0/0/1 1 bri-voice up dorm none none y
    0/0/1 2 bri-voice up dorm none none y
    0/1/0 1 bri-voice up dorm none none y
    0/1/0 2 bri-voice up dorm none none y
    0/1/1 1 bri-voice up dorm none none y
    0/1/1 2 bri-voice up dorm none none y

    I found out a solution. The problem is generated by insufficient DSP resources (PVDM2-8, I need more...).I had rearranged the position of the card and of course I've lost one ISDN BRI port. The result is as follow:
    sh voice port summ
    IN OUT
    PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
    ============== == ============ ===== ==== ======== ======== ==
    0/0/0 1 bri-voice up dorm none none y
    0/0/0 2 bri-voice up dorm none none y
    0/0/1 1 bri-voice up dorm none none y
    0/0/1 2 bri-voice up dorm none none y
    0/1/0 -- fxs-ls up dorm on-hook idle y
    0/1/1 -- fxs-ls up dorm on-hook idle y
    0/2/0 1 bri-voice up dorm none none y
    0/2/0 2 bri-voice up dorm none none y
    voice-port 0/0/0
    voice-port 0/0/1
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/2/0
    I hope that this will help anyone with this situation.

  • Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

    Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
    I am having trouble making outgoing call or answering incoming call.
    When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
    For incoming call, it rings but when I pick up the call nothing happens,
    Put the receiver back on hook, the phone carries on ringing. I am in UK
    and just trying to set up test system with one analogue line. Any help will
    be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
    Thank you for your help.
    hostname Test-CME
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.10.10.1 10.10.10.10
    ip dhcp excluded-address 10.139.139.1 10.139.139.10
    ip dhcp pool host
    network 10.10.10.0 255.255.255.0
    default-router 10.10.10.1
    option 150 ip 10.10.10.1
    ip dhcp pool data
    network 10.139.139.0 255.255.255.0
    default-router 10.139.139.1
    dns-server 10.139.139.5
    voice-card 0
    no dspfarm
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    h323
    sip
    header-passing
    registrar server expires max 3600 min 3600
    interface FastEthernet0/1
    no ip address
    no ip mroute-cache
    duplex auto
    speed auto
    no shut
    interface FastEthernet0/1.2
    description ** Data VLAN **
    encapsulation dot1Q 2
    ip address 10.139.139.1 255.255.255.0
    interface FastEthernet0/1.3
    description ** Voice VLAN **
    encapsulation dot1Q 3
    ip address 10.10.10.1 255.255.255.0
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:
    tftp-server flash:S00104000100.sbn
    tftp-server flash:TERM41.7-0-3-0S.loads
    tftp-server flash:term61.default.loads
    tftp-server flash:term41.default.loads
    tftp-server flash:CVM41.2-0-2-26.sbn
    tftp-server flash:cnu41.2-7-6-26.sbn
    tftp-server flash:Jar41.2-9-2-26.sbn
    tftp-server flash:term70.default.loads
    tftp-server flash:term71.default.loads
    tftp-server flash:cnu70.2-7-6-26.sbn
    tftp-server flash:Jar70.2-9-2-26.sbn
    tftp-server flash:TERM70.7-0-3-0S.loads
    tftp-server flash:CVM70.2-0-2-26.sbn
    control-plane
    voice-port 0/3/0
    connection plar opx 202
    caller-id enable
    dial-peer voice 1 pots
    incoming called-number .
    destination-pattern 9T
    port 0/3/0
    telephony-service
    load 7914 S00104000100
    load 7941 TERM41.7-0-3-0S
    load 7961 TERM41.7-0-3-0S
    load 7970 TERM70.7-0-3-0S
    max-ephones 20
    max-dn 40
    ip source-address 10.10.10.1 port 2000
    calling-number initiator
    service phone videoCapability 1
    system message MKC CME
    url services http://10.10.10.1/voiceview/common/login.do
    url authentication
    http://10.10.10.1/voiceview/authentication/authenticate.do
    time-zone 21
    date-format dd-mm-yy
    voicemail 600
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    moh music-on-hold.au
    web admin system name admin secret 0 test
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 9.T
    secondary-dialtone 9
    create cnf-files
    ephone-dn 1 dual-line
    number 201
    label 201
    description Sarah
    name Sarah
    ephone-dn 2 dual-line
    number 202
    label 202
    description Vitthal
    name User2 Vitthal
    ephone-dn 3 dual-line
    number 203 secondary
    label 203
    description Neil
    name User3 Neil
    ephone 1
    video
    username "user1" password 201
    mac-address 0018.18EE.947F
    type 7961 addon 1 7914
    button 1:1
    ephone 2
    video
    username "user2" password 202
    mac-address 0018.18BB.B973
    type 7941
    button 1:2
    ephone 3
    video
    username "user3" password 203
    mac-address 0018.1885.6BA2
    type 7970
    button 1:3

    Hi
    Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
    Thank you for your help.
    Vitthal

  • Cisco 1760 and VoIP gateway

    Hello NetProf!
    I'm repeating my request for help, mabey clearing a few things out.
    1. We have a cisco 1760 router running CCME
    2. Some connected to it cisco 79xx ip-phones
    3. A third party gatekeeper - MikroTik router
    4. Every device is logged in the gatekeeper, and every call i settled with the use of it.
    5. We have a third party VoIP gateway - MultiTechs MultiVoIP - also registered in the gatekeeper.
    6. Now the connections history:
    a) when phoning from the gateway to cisco - everything works fine.
    b) when phoning fromn cisco to the gateway - the connection failes - it looks like CISCO ISN'T FORWARDING ANY INDENTITY DATA - NO IP ADDRESS, AND H323-ID - GETS TO THE GATEWAY!!!!!
    Please help!!
    Michal Podoski

    Check if there are some known issues documented here:
    http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122relnt/1700/rn1700yj.htm

  • 2811 and VIC2-2BRI-NT/TE. CCM 4.1.3

    Hi,
    I've an H323 gateway with a VIC2-2BRI-NT/TE to connect directly an ISDN Phone. I'm searching to display a name for this phone when it call an IP Phone. Anyone an idea ? The station-name voice-port command doesn't work with BRI interface. Thanks

    Here it is :
    boot system flash:c2800nm-spservicesk9-mz.124-4.XC1.bin
    isdn switch-type basic-net3
    voice-card 0
    no dspfarm
    voice class h323 1
    h225 timeout tcp establish 3
    call preserve
    interface BRI0/0/0
    no ip address
    isdn switch-type basic-net3
    isdn overlap-receiving
    isdn protocol-emulate network
    isdn layer1-emulate network
    isdn incoming-voice voice
    isdn send-alerting
    isdn sending-complete
    isdn outgoing display-ie
    isdn skipsend-idverify
    line-power
    interface BRI0/0/1
    no ip address
    isdn switch-type basic-net3
    isdn overlap-receiving
    isdn protocol-emulate network
    isdn layer1-emulate network
    isdn incoming-voice voice
    isdn send-alerting
    isdn sending-complete
    isdn outgoing display-ie
    isdn skipsend-idverify
    line-power
    ip route 0.0.0.0 0.0.0.0 X.Y.Z.W
    voice-port 0/0/0
    compand-type a-law
    cptone CH
    dial-peer voice 10 pots
    tone ringback alert-no-PI
    preference 1
    destination-pattern 4976
    direct-inward-dial
    port 0/0/1
    forward-digits all
    dial-peer voice 20 voip
    preference 1
    destination-pattern 6671
    progress_ind setup enable 3
    voice-class h323 1
    session target ipv4:10.16.246.41
    codec g711ulaw
    ip qos dscp cs5 media
    no vad
    dial-peer voice 21 voip
    preference 2
    destination-pattern 6671
    progress_ind setup enable 3
    session target ipv4:10.19.133.41
    codec g711ulaw
    ip qos dscp cs5 media
    no vad

  • Cisco 2801 and VIC2-2E/M Card

    Hi Experts,
    One problem with my cisco 2801, when I have inserted the E&M card it is not supporting on the slot. The output of show diag is as attahced.
    IOS is : c2801-ipbase-mz.124-1c.bin
    Any help would be appreciated..
    Thanks,
    Hardik..

    You need a voice capable IOS feature set. The minimum is IP Voice for this card. Please see the following link for confirmation.
    http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.html
    Hope this helps. If so, please rate the post.
    Brandon

  • Cisco 1760 and E1 to VoIP Gateway

    Hello!
    Recently we've developed a test VoIP network combined out of a verry differently branched devices. It's working quite well, excluding one part.
    The problem occures when trying to call from a CCME Cisco IP phone registered in a gatekeeper to a MultiTechs Multivoip E1/VoIP gateway (which is connected to our PBX). In MvOIPs logs - I can focus Cisco Phone trying to connect using the correct codec, matching gateway prefix - BUT LEAVING NO IP ADDRESS OR H.323 ID. Mabey some ideas???
    Network is H.323 based.
    Thanks in advance.
    Michael

    Hi Micheal,
    Can your PBX see the digits being passed to it?
    Thanks,
    Erik

  • VIC2-2FXO and VIC-2FXO

    In my environment there is a PBX connecto VIC2-2FXO at router CISCO1751-V. I have an old PBX and when I change the card to VIC-2FXO(EOL), I have from from PBX e works fine. But if I return the new card VIC2-2FXO it doesn't work, even tone is missing. What a real difference between VIC-2FXO and VIC2-2FXO

    Hi Almir,
    The card is comatible with 1751-4V. The VIC2 cards are the new generation cards. Working wise they are no different. I checked the configs nd they looked kinda incomplete. Usually the FXO works with a "connection plar/trunk". Neither did I notice any voip dial-peers.
    Sample config for call flow : (phone---pbx---vic2-fxo---router1--ip---router2---fxs--phone)
    voice-port 2/0
    cptone BR
    connection plar 3000
    dial-peer voice 100 voip
    destination-pattern 3000
    session target ipv4:p.q.r.s
    dial-peer voice 1 pots
    destination-pattern .T
    port 2/0
    The above config should be fine for inbound and outbound calls. If this doesn't work please send me the following-
    1. Exact call flow eg
    2. deb voice ccapi inout
    3. debug vpm signal
    4. debug vtsp events
    5. debug vtsp session
    Subhrojyoti

  • ATA vs VG202 vs VIC3-2FXS-E/DID & Wireless

    What is best solution moving forward?
    Fax server probably two years out.
    Background:
    I have 34 locations
    30 locations have 2 analog devices
    4 Operations have 26, 14, 15, 10 analog devices
    Currently we use ATA 188 and 186 and one VIC2-2FXS
    We Have intermittent problems receiving faxes from Fax servers or other customers in general.

    The VG20x are nice because you can use them as a full blown router (VPN, IGP, etc).
    I think you'll have more cost per port using a VIC3 rather than VG204. Their capabilities will be equal, as opposed to when the ATAs were in use.
    The ATAs are on their way out, and I think you'll find the VG20x to be an easier product to use and it will work better with faxes/modems. The ATAs don't have great fax/modem support where the VG20x will have T38 support and modem support.
    For the locations with 15+ devices it may be worth looking into the VG224 as well, depending on usage.
    -nick

  • MGCP and H.323 in same router

    We have few 3825 and 3845 routers with VWIC-1MFT-T1, VIC2-2FXS and VIC2-2FXO cards. CCM is 4.1(3)SR1
    Checked MGCP & H.323 can support analog FXO interfaces loop-start/ground-start signaling, analog FXS interfaces loop-start/ground-start signaling and T1/E1 ISDN PRI Q.931 interfaces.
    http://www.cisco.com/en/US/products/ps5855/products_data_sheet09186a0080182d38.html
    Anyone has experience in below configurations? For example,
    1. Config only MGCP to support all three above voice modules (T1, FXS, FXO) in a router (would like to confirm)
    2. Or config only H.323 to support all modules in a router (should be okay, no issue)
    3. Or config MGCP for T1 and H.323 for FXS & FXO in a router (would like to confirm)
    4. Or config MGCP for T1 in one router and config H.323 for FXS & FXO in another router (should be okay, no issue)
    Thank you in advance.

    All options are valid. You can have MGCP and H.323 to control seperate ports on the same router. If you go with option 3 (my guess is this is what you want) make sure to point the dial-peers to the appropriate ports.
    HTH,
    Chris

  • VIC2-2FXO picks up then hangs up

    Hi, I am having issues. All my VIC2-2FXO and VIC2-4FXO are picking up, then hanging up right away. I tried them on 1760s and 2811s. I tried a combination of supervisory disconnect, but can't get it to work. On 1760s, if I put a VIC-2FXO in the place of the VIC2-2FXO it works just fine. Is there a special command needed for VIC2s???

    no logging console was set DOH...
    here's debug's
    May 20 15:55:22.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
    May 20 15:55:22.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
    May 20 15:55:22.892 EDT: htsp_timer_stop
    May 20 15:55:22.996 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:22.996 EDT: htsp_call_bridged invoked
    May 20 15:55:22.996 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:23.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
    May 20 15:55:23.144 EDT: htsp_timer2 - 350 msec
    May 20 15:55:23.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
    May 20 15:55:23.496 EDT: htsp_timer_stop
    May 20 15:55:23.496 EDT: htsp_timer_stop2
    May 20 15:55:23.496 EDT: htsp_timer_stop3
    May 20 15:55:23.876 EDT: htsp_timer_stop3
    May 20 15:55:23.896 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
    May 20 15:55:23.896 EDT: htsp_timer_stop
    May 20 15:55:23.896 EDT: htsp_timer_stop2
    May 20 15:55:23.896 EDT: htsp_timer_stop3
    May 20 15:55:23.896 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
    May 20 15:55:23.896 EDT: htsp_timer - 2000 msec
    May 20 15:55:25.896 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
    May 20 15:55:25.896 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
    May 20 15:55:26.744 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
    May 20 15:55:26.744 EDT: htsp_timer - 125 msec
    May 20 15:55:26.872 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
    May 20 15:55:26.872 EDT: htsp_timer - 10000 msec
    May 20 15:55:28.888 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
    May 20 15:55:28.888 EDT: fxols_ringing_not
    May 20 15:55:28.888 EDT: htsp_timer_stop
    May 20 15:55:28.888 EDT: htsp_timer_stop3 htsp_setup_ind
    May 20 15:55:28.888 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55  orig called=
    May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
    May 20 15:55:28.892 EDT: fxols_wait_setup_ack:
    May 20 15:55:28.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
    May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
    May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
    May 20 15:55:28.892 EDT: htsp_timer_stop
    May 20 15:55:28.964 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:28.964 EDT: htsp_call_bridged invoked
    May 20 15:55:28.964 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:29.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
    May 20 15:55:29.144 EDT: htsp_timer2 - 350 msec
    May 20 15:55:29.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
    May 20 15:55:29.496 EDT: htsp_timer_stop
    May 20 15:55:29.496 EDT: htsp_timer_stop2
    May 20 15:55:29.496 EDT: htsp_timer_stop3
    May 20 15:55:29.560 EDT: htsp_timer_stop3
    May 20 15:55:29.576 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
    May 20 15:55:29.576 EDT: htsp_timer_stop
    May 20 15:55:29.576 EDT: htsp_timer_stop2
    May 20 15:55:29.576 EDT: htsp_timer_stop3
    May 20 15:55:29.576 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
    May 20 15:55:29.576 EDT: htsp_timer - 2000 msec
    May 20 15:55:31.576 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
    May 20 15:55:31.576 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
    May 20 15:55:32.744 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
    May 20 15:55:32.744 EDT: htsp_timer - 125 msec
    May 20 15:55:32.872 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
    May 20 15:55:32.872 EDT: htsp_timer - 10000 msec
    May 20 15:55:34.888 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
    May 20 15:55:34.888 EDT: fxols_ringing_not
    May 20 15:55:34.888 EDT: htsp_timer_stop
    May 20 15:55:34.888 EDT: htsp_timer_stop3 htsp_setup_ind
    May 20 15:55:34.888 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55  orig called=
    May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
    May 20 15:55:34.892 EDT: fxols_wait_setup_ack:
    May 20 15:55:34.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
    May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
    May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
    May 20 15:55:34.892 EDT: htsp_timer_stop
    May 20 15:55:34.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:34.932 EDT: htsp_call_bridged invoked
    May 20 15:55:34.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:35.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
    May 20 15:55:35.144 EDT: htsp_timer2 - 350 msec
    May 20 15:55:35.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
    May 20 15:55:35.496 EDT: htsp_timer_stop
    May 20 15:55:35.496 EDT: htsp_timer_stop2
    May 20 15:55:35.496 EDT: htsp_timer_stop3
    May 20 15:55:35.560 EDT: htsp_timer_stop3
    May 20 15:55:35.576 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
    May 20 15:55:35.576 EDT: htsp_timer_stop
    May 20 15:55:35.576 EDT: htsp_timer_stop2
    May 20 15:55:35.576 EDT: htsp_timer_stop3
    May 20 15:55:35.576 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
    May 20 15:55:35.576 EDT: htsp_timer - 2000 msec
    May 20 15:55:37.576 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
    May 20 15:55:37.576 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
    May 20 15:55:38.748 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
    May 20 15:55:38.748 EDT: htsp_timer - 125 msec
    May 20 15:55:38.876 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
    May 20 15:55:38.876 EDT: htsp_timer - 10000 msec
    May 20 15:55:40.892 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
    May 20 15:55:40.892 EDT: fxols_ringing_not
    May 20 15:55:40.892 EDT: htsp_timer_stop
    May 20 15:55:40.892 EDT: htsp_timer_stop3 htsp_setup_ind
    May 20 15:55:40.892 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55  orig called=
    May 20 15:55:40.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
    May 20 15:55:40.892 EDT: fxols_wait_setup_ack:
    May 20 15:55:40.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
    May 20 15:55:40.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
    May 20 15:55:40.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
    May 20 15:55:40.896 EDT: htsp_timer_stop
    May 20 15:55:40.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:40.936 EDT: htsp_call_bridged invoked
    May 20 15:55:40.936 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:41.148 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
    May 20 15:55:41.148 EDT: htsp_timer2 - 350 msec
    May 20 15:55:41.500 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
    May 20 15:55:41.500 EDT: htsp_timer_stop
    May 20 15:55:41.500 EDT: htsp_timer_stop2
    May 20 15:55:41.500 EDT: htsp_timer_stop3
    May 20 15:55:41.564 EDT: htsp_timer_stop3
    May 20 15:55:41.580 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
    May 20 15:55:41.580 EDT: htsp_timer_stop
    May 20 15:55:41.580 EDT: htsp_timer_stop2
    May 20 15:55:41.580 EDT: htsp_timer_stop3
    May 20 15:55:41.580 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
    May 20 15:55:41.580 EDT: htsp_timer - 2000 msec
    May 20 15:55:43.580 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
    May 20 15:55:43.580 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
    May 20 15:55:44.748 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
    May 20 15:55:44.748 EDT: htsp_timer - 125 msec
    May 20 15:55:44.876 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
    May 20 15:55:44.876 EDT: htsp_timer - 10000 msec
    May 20 15:55:46.892 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
    May 20 15:55:46.892 EDT: fxols_ringing_not
    May 20 15:55:46.892 EDT: htsp_timer_stop
    May 20 15:55:46.892 EDT: htsp_timer_stop3 htsp_setup_ind
    May 20 15:55:46.892 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55  orig called=
    May 20 15:55:46.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
    May 20 15:55:46.892 EDT: fxols_wait_setup_ack:
    May 20 15:55:46.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
    May 20 15:55:46.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
    May 20 15:55:46.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
    May 20 15:55:46.896 EDT: htsp_timer_stop
    May 20 15:55:46.968 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:46.968 EDT: htsp_call_bridged invoked
    May 20 15:55:46.972 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
    May 20 15:55:47.148 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
    May 20 15:55:47.148 EDT: htsp_timer2 - 350 msec
    May 20 15:55:47.500 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
    May 20 15:55:47.500 EDT: htsp_timer_stop
    May 20 15:55:47.500 EDT: htsp_timer_stop2
    May 20 15:55:47.500 EDT: htsp_timer_stop3
    May 20 15:55:47.564 EDT: htsp_timer_stop3
    May 20 15:55:47.580 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
    May 20 15:55:47.580 EDT: htsp_timer_stop
    May 20 15:55:47.580 EDT: htsp_timer_stop2
    May 20 15:55:47.580 EDT: htsp_timer_stop3
    May 20 15:55:47.580 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
    May 20 15:55:47.580 EDT: htsp_timer - 2000 msec
    May 20 15:55:49.228 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
    May 20 15:55:49.580 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
    May 20 15:55:49.580 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]

Maybe you are looking for

  • Problem with ResultSet

    Hi all, i m giving select query n after that rs = prepareStmt.executeQuery(); after that i gave one sout to chk the flow it is coming after that statement properly.and after that i gave :--- while (rs.next()) sout("test"); but it didn't print. if i r

  • Fix Actions panel

    Let users drag an action step to the end of the list. Let users select "Close" for "Insert Menu Item...". Don't expand actions when played. Allow Save in Button Mode Sometimes I feel like I'm telling a child how to pour cereal.

  • Printers not showing in Devices and Printers menu

    Hello all, When adding a new network printer, users are able to add the printer and install the driver. The printer appears to install successfully: can be printed to from documents (Word, Excel etc), appears in Device Manager, appears in Print Manag

  • System.setOut() and System.setErr()

    Hi In my application, I capture all of the println()s to System.out and System.err so that I can display them in a TextArea using a Thread as such: final PipedInputStream stdoutStream = new PipedInputStream(); PrintStream stdout = new PrintStream(new

  • Knowing parameters of procedures (dynamically)

    Hi! I have the following problem: There is a situation where a programA (user) has to make a requests by sending stored procedures. The procedures have variable parameters (like param1 in, param2 inout, param3 out,...etc.). For e.g. procA(param1, in