1841 ISR Router and Client VPN

Hi,
CAn I terminate VPN clients on a 1841 ISR Router? What are the requirement for that e.g IOS version DRAM or Flash?
Plz Help
Regards

sanjay
You should certainly be able to terminate VPN client sessions on an 1841 router. For 1841 you need either 12.3T or 12.4 code. For feature set you need something like Advanced Security or Advanced IP Services. these require 128 MB memory and 32 MB flash which is the default amount of memory and flash that ship with the router.
HTH
Rick

Similar Messages

ASA 5505 site-to-site VPN tunnel and client VPN sessions

Hello all
I have several years of general networking experience, but I have not yet had to set up an ASA from the ground up, so please bear with me.
I have a client who needs to establish a VPN tunnel from his satellite office (Site A) to his corporate office (Site Z). His satellite office will have a single PC sitting behind the ASA. In addition, he needs to be able to VPN from his home (Site H) to Site A to access his PC.
The first question I have is about the ASA 5505 and the various licensing options. I want to ensure that an ASA5505-BUN-K9 will be able to establish the site-to-site tunnel as well as allow him to use either the IPsec or SSL VPN client to connect from Site H to Site A. Would someone please confirm or deny that for me?
Secondly, I would like to verify that no special routing or configuration would need to take place in order to allow traffic not destined for Site Z (i.e., general web browsing or other traffic to any resource that is not part of the Site Z network) to go out his outside interface without specifically traversing the VPN tunnel (split tunneling?)
Finally, if the client were to establish a VPN session from Site H to Site A, would that allow for him to connect directly into resources at Site Z without any special firewall security rules? Since the VPN session would come in on the outside interface, and the tunnel back to Site Z goes out on the same interface, would this constitute a split horizon scenario that would call for a more complex config, or will the ASA handle that automatically without issue?
I don't yet have the equipment in-hand, so I can't provide any sample configs for you to look over, but I will certainly do so once I've got it.
Thanks in advance for any assistance provided!

First question:
Yes, 5505 will be able to establish site-to-site tunnel, and he can use IPSec vpn client, and SSL VPN (it comes with 2 default SSL VPN license).
Second question:
Yes, you are right. No special routing is required. All you need to configure is site-to-site VPN between Site A and Site Z LAN, and the internet traffic will be routed via Site A internet. Assuming you have all the NAT statement configured for that.
Last question:
This needs to be configured, it wouldn't automatically allow access to Site Z when he VPNs in to Site A.
Here is what needs to be configured:
1) Split tunnel ACL for VPN Client should include both Site Z and Site A LAN subnets.
2) On site A configures: same-security-traffic permit intra-interface
3) Crypto ACL for the site-to-site tunnel between Site Z and Site A needs to include the VPN Client pool subnet as follows:
On Site Z:
access-list permit ip
On Site A:
access-list permit ip
4) NAT exemption on site Z needs to include vpn client pool subnet as well.
Hope that helps.
Message was edited by: Jennifer Halim

Problem with Cisco 861W router and outgoing VPN

We have a Cisco 861W router that is blocking an outgoing PPTP on the internal access point only. The outgoing VPN works when the traffic is through a wired connection or the connection is on another access point. We fail to make a connection only when connection to the 861W's internal Access Point.
Here is the Access Point Configuration:
Current configuration : 2100 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname obap
enable secret 5 $1$.1RF$go1D7WITXUn3s8TUaw3tC.
no aaa new-model
dot11 syslog
dot11 ssid OLIVER
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 0 XXXXXXXXXXX
username XXXXXX privilege 15 secret 5 $1$Wc0K$OzcQDDQfjHP6La31eXMoG/
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid OLIVER
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecti
ng AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
banner login ^CC
% Password change notice.
Default username/password setup on AP is cisco/cisco with priv¾ilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
^C
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
cns dhcp
end
obap#
Here is the Router's Configuration:
Current configuration : 5908 bytes
! No configuration change since last restart
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname obrouter
boot-start-marker
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 $1$i9XE$DjxFVAEC9nC4/r6EQKCd6/
no aaa new-model
memory-size iomem 10
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-1856757619
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1856757619
revocation-check none
rsakeypair TP-self-signed-1856757619
crypto pki certificate chain TP-self-signed-1856757619
certificate self-signed 01
3082024D 308201B6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383536 37353736 3139301E 170D3036 30313032 31323030
34345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38353637
35373631 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B1A4 FB786547 3D582260 03DB768D 116BDE9A 309FBA04 B53F77B0 BFE32344
7C3439B3 97192B36 760A9411 1D5C7549 8D86F532 ABA44F53 0D08B7F4 A9A747D5
071330C3 65BF25A8 927F3596 29BB5A80 90C8D169 22268476 3B8DDE1E FDB7170D
B4820D03 5580A849 A92C7E76 9AC10867 505A2FEE 64360741 7F9DBDBF 3D79982C
F81D0203 010001A3 75307330 0F060355 1D130101 FF040530 030101FF 30200603
551D1104 19301782 156F6272 6F757465 722E6272 75736868 6F672E63 6F6D301F
0603551D 23041830 168014D8 5BC2FFB2 967A4C7B 11B44122 5C8D31F7 749B9230
1D060355 1D0E0416 0414D85B C2FFB296 7A4C7B11 B441225C 8D31F774 9B92300D
06092A86 4886F70D 01010405 00038181 005901F1 C239074B B8213567 CF7B65BF
DAFE4557 69B2A3B1 5F2593C7 A54B9598 23FD5E7A 563AA6E0 AFB25801 FA0061E8
F9545372 DB600B3A BE68AE65 1EDA593E 6A0C96B8 5A4136AF 393F9AAC 651E1C36
B8B7C6C0 47936C24 D2ECE9A5 9446EE32 FC7461FA AD8CF1CE A7FBF341 07E9C3C6
505AB88D 0E7FCAFC 5792298A E5E4D1FE CC
        quit
no ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.99
ip dhcp pool ccp-pool1
   import all
   network 192.168.0.0 255.255.255.0
   dns-server 216.49.160.10 216.49.160.66
   default-router 192.168.0.1
ip cef
no ip bootp server
ip domain name brushhog.com
ip name-server 216.49.160.10
ip name-server 216.49.160.66
license udi pid CISCO861W-GN-A-K9 sn FTX155281FY
username tech38 privilege 15 secret 5 $1$d/4Z$n/23EsXbzfHF5XfJ8Nv.y0
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
duplex auto
speed auto
pppoe-client dial-pool-number 1
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXXXXXXXXX
ppp chap password 7 XXXXXXXXXXXXXXXX
ppp pap sent-username XXXXXXXXXXXXXX password 7 XXXXXXXXXXX
no cdp enable
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static tcp 192.168.0.25 80 interface Dialer0 80
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Any help would be appreciated

Hello,
i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Can someone help?
Thank you.
Here is my config for internal AP and router.

Pix 501 and Client VPN's

Hi, I've had this 501 for several months now and really stuggled to get the client VPN side working.
I can get site to site working with no problems using the wizard but the Client VPN never works.
Latest i've set it up for pptp which I can get the client to connect with no problems but fails to get any traffic from the pix - I can however ping the remote PC from a PC behind the PIX.
I'm setting these up by the PDM buy i've attached a copy of the config anyway.
Best,
Chris

Hi Kamal.
It didnt like the command
nat (inside) 0 access0list nonat
I can attach via Cisco VPN Client but the same occurs - I can ping the remote from the network - but not the other way round.
Config attached. - Best, Chris
: Written by enable_15 at 02:14:05.990 UTC Mon Feb 12 2007
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxx
passwd xxx
hostname pixfirewall
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list nonat permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list outside_cryptomap_dyn_20 permit ip any 10.10.10.0 255.255.255.240
access-list split permit ip 192.168.1.0 255.255.255.0 any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 213.x.146.72 255.255.x.0
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpnpool 10.10.10.1-10.10.10.10
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route outside 0.0.0.0 0.0.0.x.249.x.65 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto dynamic-map cisco 1 set transform-set myset
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map dyn-map 20 ipsec-isakmp dynamic cisco
crypto map dyn-map interface outside
isakmp enable outside
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash md5
isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup vpn address-pool vpnpool
vpngroup vpn dns-server 192.168.1.1
vpngroup vpn idle-time 1800
vpngroup vpn password 634083
vpngroup VPNclient split-tunnel split
vpngroup VPNclient idle-time 1800
vpngroup VPNclient password ******
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd dns 89.238.129.211
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username chris password 9DgK/T8KJkq.BhX6 encrypted privilege 15
terminal width 80
Cryptochecksum:xxx
: end

Airport Express both as router and client?

Hi,
I would like to do the following: With Airport Express (AE ) linked to internet, I would like to connect AE to my loudspeakers. I would like to use AE as a router to my MacBookPro (MBP) to stream music from the internet via the MBP to my loudspeakers.
How is that possible?
Thanks for your tips!
Best regards,
Leif

Yes, I know about Airfoil as part of the solution
Sorry for the confusion, but you did not mention this in your original post, so we did not know that you already knew this.
I wondered whether I could use AE connected to internet and as a router, send the signals to my laptop and then my laptop via Airfoil to contact the AE for it to transmit the music to my loudspeakers. All at the same time with one AE.
As I said, you can do this easily. I'm assuming that your modem and your stereo are both close enough to the AirPort Express to allow for convenient connections.
AirTunes is enabled by default on the AirPort Express, but you might want to confirm this again when you configure the AirPort Express.

VPN Client and AAA services on a Cisco ISR Router

Hi, my name is Jim, and I was just promoted as a trainer for the company I work for. Part of my new challenge is understanding how the configuration files in both my Terminal Services/VPN Router and Core Router work, so for many of you, these questions are going to seem very fundamental, but please help, I am an instructor in training. I hold a CCNA, CCNA-Wireless, and a CCSI cert, but I have little working experience in building and maintaining a lab....hence the need for this inquiry.
So to my questions. In our lab environment, we have a router that acts as our terminal services router and VPN router. Each laptop that connects to the lab has the Cisco VPN client loaded onto it, as well as my laptop that I teach from. My questions are these:
1. What parts of the AAA output of the running configuration tell me how to configure the VPN clients on my laptops?
2. I am using crypto key generate RSA at 1024 bits on the VPN/TS router, so does that tell me how to configure some part of the client?
3. In our lab, we are going to use a direct connection to an AP to get connected to the network, and how will the absence of an Internet connection affect the settings on the VPN client, or will they?
4. Are there helpful articles I can read that will answer some or all of these questions?
Thanks in advance,
Jim

Hi Jim,
congratulations
Assuming a basic setup, your router will have something like this:
crypto isakmp client configuration group MyGroup
key cisco123
So on the client, you configure it to use MyGroup as the group name, and cisco123 as the (group) password.
I'm not sure I understand your question #3 and what you mean by "AP" (Access Point? So WiFi?). In any case you don't need Internet access per se, as long as you have network (IP) connectivity between the host running the vpnclient and the VPN router.
Does this help?
Herbert

VPN between ASA5505 Easy VPN Server and 881G Router as Easy VPN Client

Hello,
I have problem in VPN between ASA5505 Easy VPN Server and 881G Router as Easy VPN Client. ASA 5505 have 7.2.3 software and 881G router have 15.1 software.
881G is configured as hardware client in network exstention mode, and it is placed behind NAT. ASA5505 is working as server. Same VPN Group works correctly from VPN software clients.
When I send traffic from 881G client side, in show cryto sessin detail I see encrypted packets. But with same command I dont see decrypted packet on ASA5505 side. On both devices Phase 1 and Phase 2 are UP.
VPN is working when I replace ASA5505 with ASA5510 correctly with have 8.4.6 software. But problem is that i need to do this VPN between ASA5505 and 881G.
Can you help me, how can I debug or troubleshoot this problem ?
I am unable to update software on ASA5505 side.

Hello,
Hire is what my config look like:
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 60 set pfs
crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 80 set pfs
crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 100 set pfs
crypto dynamic-map outside_dyn_map 100 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 120 set pfs
crypto dynamic-map outside_dyn_map 120 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 140 set pfs
crypto dynamic-map outside_dyn_map 140 set transform-set ESP-AES-128-SHA
crypto dynamic-map outside_dyn_map 160 set pfs
crypto dynamic-map outside_dyn_map 160 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 180 set pfs
crypto dynamic-map outside_dyn_map 180 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 200 set pfs
crypto dynamic-map outside_dyn_map 200 set transform-set ESP-AES-256-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 2
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
crypto isakmp policy 3
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
tunnel-group HW-CLIENT-GROUPR type ipsec-ra
tunnel-group HW-CLIENT-GROUP general-attributes
address-pool HW-CLIENT-GROUP-POOL
default-group-policy HW-CLIENT-GROUP
tunnel-group HW-CLIENT-GROUP ipsec-attributes
pre-shared-key *******
group-policy HW-CLIENT-GROUP internal
group-policy HW-CLIENT-GROUP attributes
password-storage enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cisco_splitTunnelAcl
nem enable

Site to Site VPN Problems With 2801 Router and ASA 5505

Hello,
I am having some issue setting up a site to site ipsec VPN between a Cisco 2801 router and a Cisco ASA 5505. I was told there was a vpn previously setup with an old hosting provider, but those connections have been servered. Right now I am trying to get the sites to talk to the 2801. Here ere are my current configs, please let me know if you need anything else. Im stumped on this one. Thanks.
IP scheme at SIte A:
IP    172.19.3.x
sub 255.255.255.128
GW 172.19.3.129
Site A Ciscso 2801 Router
Current configuration : 11858 bytes
version 12.4
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname router-2801
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 4096
aaa new-model
aaa authentication login userauthen group radius local
aaa authorization network groupauthor local
aaa session-id common
clock timezone est -5
clock summer-time zone recurring last Sun Mar 2:00 1 Sun Nov 2:00
dot11 syslog
ip source-route
ip dhcp excluded-address 172.19.3.129 172.19.3.149
ip dhcp excluded-address 172.19.10.1 172.19.10.253
ip dhcp excluded-address 172.19.3.140
ip dhcp ping timeout 900
ip dhcp pool DHCP
   network 172.19.3.128 255.255.255.128
   default-router 172.19.3.129
   domain-name domain.local
   netbios-name-server 172.19.3.7
   option 66 ascii 172.19.3.225
   dns-server 172.19.3.140 208.67.220.220 208.67.222.222
ip dhcp pool VoiceDHCP
   network 172.19.10.0 255.255.255.0
   default-router 172.19.10.1
   dns-server 208.67.220.220 8.8.8.8
   option 66 ascii 172.19.10.2
   lease 2
ip cef
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp
ip inspect name SDM_LOW udp
ip inspect name SDM_LOW vdolive
no ip domain lookup
ip domain name domain.local
multilink bundle-name authenticated
key chain key1
key 1
   key-string 7 06040033484B1B484557
crypto pki trustpoint TP-self-signed-3448656681
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3448bb6681
revocation-check none
rsakeypair TP-self-signed-344bbb56681
crypto pki certificate chain TP-self-signed-3448656681
certificate self-signed 01
3082024F
            quit
username admin privilege 15 password 7 F55
archive
log config
hidekeys
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key XXXXX address 209.118.0.1
crypto isakmp key xxxxx address SITE B Public IP
crypto isakmp keepalive 40 5
crypto isakmp nat keepalive 20
crypto isakmp client configuration group IISVPN
key 1nsur3m3
dns 172.19.3.140
wins 172.19.3.140
domain domain.local
pool VPN_Pool
acl 198
crypto isakmp profile IISVPNClient
   description VPN clients profile
   match identity group IISVPN
   client authentication list userauthen
   isakmp authorization list groupauthor
   client configuration address respond
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map Dynamic 5
set transform-set myset
set isakmp-profile IISVPNClient
qos pre-classify
crypto map VPN 10 ipsec-isakmp
set peer 209.118.0.1
set peer SITE B Public IP
set transform-set myset
match address 101
qos pre-classify
crypto map VPN 65535 ipsec-isakmp dynamic Dynamic
track 123 ip sla 1 reachability
delay down 15 up 10
class-map match-any VoiceTraffic
match protocol rtp audio
match protocol h323
match protocol rtcp
match access-group name VOIP
match protocol sip
class-map match-any RDP
match access-group 199
policy-map QOS
class VoiceTraffic
    bandwidth 512
class RDP
    bandwidth 768
policy-map MainQOS
class class-default
    shape average 1500000
service-policy QOS
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$$FW_INSIDE$
ip address 172.19.3.129 255.255.255.128
ip access-group 100 in
ip inspect SDM_LOW in
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/0.10
description $ETH-VoiceVLAN$$
encapsulation dot1Q 10
ip address 172.19.10.1 255.255.255.0
ip inspect SDM_LOW in
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1
description "Comcast"
ip address PUB IP 255.255.255.248
ip access-group 102 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPN
interface Serial0/1/0
description "Verizon LEC Circuit ID: w0w13908 Site ID: U276420-1"
bandwidth 1536
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
interface Serial0/1/0.1 point-to-point
bandwidth 1536
ip address 152.000.000.18 255.255.255.252
ip access-group 102 in
ip verify unicast reverse-path
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
frame-relay interface-dlci 500 IETF
crypto map VPN
service-policy output MainQOS
interface Serial0/2/0
description "PAETEC 46.HCGS.788446.CV (Verizon ID) / 46.HCGS.3 (PAETEC ID)"
ip address 123.252.123.102 255.255.255.252
ip access-group 102 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
encapsulation ppp
crypto map VPN
service-policy output MainQOS
ip local pool VPN_Pool 172.20.3.130 172.20.3.254
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 50.00.000.110 track 123
ip route 0.0.0.0 0.0.0.0 111.252.237.000 254
ip route 122.112.197.20 255.255.255.255 209.252.237.101
ip route 208.67.220.220 255.255.255.255 50.78.233.110
no ip http server
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 20
sort-by bytes
ip nat inside source route-map COMCAST interface FastEthernet0/1 overload
ip nat inside source route-map PAETEC interface Serial0/2/0 overload
ip nat inside source route-map VERIZON interface Serial0/1/0.1 overload
ip nat inside source static tcp 172.19.3.140 21 PUB IP 21 extendable
ip access-list extended VOIP
permit ip 172.20.3.0 0.0.0.127 host 172.19.3.190
permit ip host 172.19.3.190 172.20.3.0 0.0.0.127
ip radius source-interface FastEthernet0/0
ip sla 1
icmp-echo 000.67.220.220 source-interface FastEthernet0/1
timeout 10000
frequency 15
ip sla schedule 1 life forever start-time now
access-list 23 permit 172.19.3.0 0.0.0.127
access-list 23 permit 172.19.3.128 0.0.0.127
access-list 23 permit 173.189.251.192 0.0.0.63
access-list 23 permit 107.0.197.0 0.0.0.63
access-list 23 permit 173.163.157.32 0.0.0.15
access-list 23 permit 72.55.33.0 0.0.0.255
access-list 23 permit 172.19.5.0 0.0.0.63
access-list 100 remark "Outgoing Traffic"
access-list 100 deny   ip 67.128.87.156 0.0.0.3 any
access-list 100 deny   ip host 255.255.255.255 any
access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
access-list 100 permit tcp host 172.19.3.190 any eq smtp
access-list 100 permit tcp host 172.19.3.137 any eq smtp
access-list 100 permit tcp any host 66.251.35.131 eq smtp
access-list 100 permit tcp any host 173.201.193.101 eq smtp
access-list 100 permit ip any any
access-list 100 permit tcp any any eq ftp
access-list 101 remark "Interesting VPN Traffic"
access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 101 permit ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 101 permit tcp any any eq ftp
access-list 101 permit tcp any any eq ftp-data
access-list 102 remark "Inbound Access"
access-list 102 permit udp any host 152.179.53.18 eq non500-isakmp
access-list 102 permit udp any host 152.179.53.18 eq isakmp
access-list 102 permit esp any host 152.179.53.18
access-list 102 permit ahp any host 152.179.53.18
access-list 102 permit udp any host 209.000.000.102 eq non500-isakmp
access-list 102 permit udp any host 209.000.000.102 eq isakmp
access-list 102 permit esp any host 209.000.000.102
access-list 102 permit ahp any host 209.000.000.102
access-list 102 permit udp any host PUB IP eq non500-isakmp
access-list 102 permit udp any host PUB IP eq isakmp
access-list 102 permit esp any host PUB IP
access-list 102 permit ahp any host PUB IP
access-list 102 permit ip 72.55.33.0 0.0.0.255 any
access-list 102 permit ip 107.0.197.0 0.0.0.63 any
access-list 102 deny   ip 172.19.3.128 0.0.0.127 any
access-list 102 permit icmp any any echo-reply
access-list 102 permit icmp any any time-exceeded
access-list 102 permit icmp any any unreachable
access-list 102 permit icmp any any
access-list 102 deny   ip any any log
access-list 102 permit tcp any host 172.19.3.140 eq ftp
access-list 102 permit tcp any host 172.19.3.140 eq ftp-data established
access-list 102 permit udp any host SITE B Public IP eq non500-isakmp
access-list 102 permit udp any host SITE B Public IP eq isakmp
access-list 102 permit esp any host SITE B Public IP
access-list 102 permit ahp any host SITE B Public IP
access-list 110 remark "Outbound NAT Rule"
access-list 110 remark "Deny VPN Traffic NAT"
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
access-list 110 deny   ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
access-list 110 deny   ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 110 permit ip 172.19.3.128 0.0.0.127 any
access-list 110 permit ip 172.19.10.0 0.0.0.255 any
access-list 198 remark "Networks for IISVPN Client"
access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 199 permit tcp any any eq 3389
route-map PAETEC permit 10
match ip address 110
match interface Serial0/2/0
route-map COMCAST permit 10
match ip address 110
match interface FastEthernet0/1
route-map VERIZON permit 10
match ip address 110
match interface Serial0/1/0.1
snmp-server community 123 RO
radius-server host 172.19.3.7 auth-port 1645 acct-port 1646 key 7 000000000000000
control-plane
line con 0
line aux 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
scheduler allocate 20000 1000
ntp server 128.118.25.3
ntp server 217.150.242.8
end
IP scheme at site B:
ip     172.19.5.x
sub 255.255.255.292
gw   172.19.5.65
Cisco ASA 5505 at Site B
ASA Version 8.2(5)
hostname ASA5505
domain-name domain.com
enable password b04DSH2HQqXwS8wi encrypted
passwd b04DSH2HQqXwS8wi encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.19.5.65 255.255.255.192
interface Vlan2
nameif outside
security-level 0
ip address SITE B public IP 255.255.255.224
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone est -5
clock summer-time zone recurring last Sun Mar 2:00 last Sun Oct 2:00
dns server-group DefaultDNS
domain-name iis-usa.com
same-security-traffic permit intra-interface
object-group network old hosting provider
network-object 72.55.34.64 255.255.255.192
network-object 72.55.33.0 255.255.255.0
network-object 173.189.251.192 255.255.255.192
network-object 173.163.157.32 255.255.255.240
network-object 66.11.1.64 255.255.255.192
network-object 107.0.197.0 255.255.255.192
object-group network old hosting provider
network-object host 172.19.250.10
network-object host 172.19.250.11
access-list 100 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
access-list 100 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
access-list 10 extended deny ip 0.0.0.0 255.0.0.0 any
access-list 10 extended deny ip 127.0.0.0 255.0.0.0 any
access-list 10 extended deny ip 169.254.0.0 255.255.0.0 any
access-list 10 extended deny ip 172.16.0.0 255.255.0.0 any
access-list 10 extended deny ip 224.0.0.0 224.0.0.0 any
access-list 10 extended permit icmp any any echo-reply
access-list 10 extended permit icmp any any time-exceeded
access-list 10 extended permit icmp any any unreachable
access-list 10 extended permit icmp any any traceroute
access-list 10 extended permit icmp any any source-quench
access-list 10 extended permit icmp any any
access-list 10 extended permit tcp object-group old hosting provider any eq 3389
access-list 10 extended permit tcp any any eq https
access-list 10 extended permit tcp any any eq www
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.0 255.255.255.128
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
pager lines 24
logging enable
logging timestamp
logging console emergencies
logging monitor emergencies
logging buffered warnings
logging trap debugging
logging history debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip verify reverse-path interface inside
ip verify reverse-path interface outside
ip audit name jab attack action alarm drop reset
ip audit name probe info action alarm drop reset
ip audit interface outside probe
ip audit interface outside jab
ip audit info action alarm drop reset
ip audit attack action alarm drop reset
ip audit signature 2000 disable
ip audit signature 2001 disable
ip audit signature 2004 disable
ip audit signature 2005 disable
icmp unreachable rate-limit 1 burst-size 1
icmp permit 75.150.169.48 255.255.255.240 outside
icmp permit 72.44.134.16 255.255.255.240 outside
icmp permit 72.55.33.0 255.255.255.0 outside
icmp permit any outside
icmp permit 173.163.157.32 255.255.255.240 outside
icmp permit 107.0.197.0 255.255.255.192 outside
icmp permit 66.11.1.64 255.255.255.192 outside
icmp deny any outside
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 100
nat (inside) 1 0.0.0.0 0.0.0.0
access-group 10 in interface outside
route outside 0.0.0.0 0.0.0.0 174.78.151.225 1
timeout xlate 3:00:00
timeout conn 24:00:00 half-closed 0:10:00 udp 0:10:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 24:00:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http 107.0.197.0 255.255.255.192 outside
http 66.11.1.64 255.255.255.192 outside
snmp-server host outside 107.0.197.29 community *****
snmp-server host outside 107.0.197.30 community *****
snmp-server host inside 172.19.250.10 community *****
snmp-server host outside 172.19.250.10 community *****
snmp-server host inside 172.19.250.11 community *****
snmp-server host outside 172.19.250.11 community *****
snmp-server host outside 68.82.122.239 community *****
snmp-server host outside 72.55.33.37 community *****
snmp-server host outside 72.55.33.38 community *****
snmp-server host outside 75.150.169.50 community *****
snmp-server host outside 75.150.169.51 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map VPNMAP 10 match address 110
crypto map VPNMAP 10 set peer 72.00.00.7 old vpn public ip Site B Public IP
crypto map VPNMAP 10 set transform-set ESP-3DES-MD5
crypto map VPNMAP 10 set security-association lifetime seconds 86400
crypto map VPNMAP 10 set security-association lifetime kilobytes 4608000
crypto map VPNMAP interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 172.19.5.64 255.255.255.192 inside
telnet 172.19.3.0 255.255.255.128 outside
telnet timeout 60
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
management-access inside
dhcpd dns 172.19.3.140
dhcpd wins 172.19.3.140
dhcpd ping_timeout 750
dhcpd domain iis-usa.com
dhcpd address 172.19.5.80-172.19.5.111 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection scanning-threat shun except object-group old hosting provider
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 128.118.25.3 source outside
ntp server 217.150.242.8 source outside
tunnel-group 72.00.00.7 type ipsec-l2l
tunnel-group 72.00.00.7 ipsec-attributes
pre-shared-key *****
tunnel-group old vpn public ip type ipsec-l2l
tunnel-group old vpn public ip ipsec-attributes
pre-shared-key *****
tunnel-group SITE A Public IP type ipsec-l2l
tunnel-group SITE A Public IP ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect netbios
inspect tftp
inspect pptp
inspect sip
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:
: end

I have removed the old "set peer" and have added:
IOS router:
access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.65
ASA fw:
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
on the router I have also added;
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
Here is my acl :
access-list 110 remark "Outbound NAT Rule"
access-list 110 remark "Deny VPN Traffic NAT"
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
access-list 110 deny   ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
access-list 110 deny   ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 110 deny   ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 110 permit ip 172.19.3.128 0.0.0.127 any
access-list 110 permit ip 172.19.10.0 0.0.0.255 any
access-list 110 deny   ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
access-list 198 remark "Networks for IISVPN Client"
access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
Still no ping tothe other site.

Cisco VPN Client and Quick VPN interaction?

I have both a Cisco VPN client for connecting to my company LAN and a QuickVPN client for connecting to my home LAN installed on my W2K laptop. Both start and run correctly, and both connect just as they should. My home LAN uses a WRV54G router to provide VPN connection. I can alternate back and forth between the two clients and connect to each LAN with no obvious issues, but not at the same time, of course.
Here's the question. When I connect to the home LAN, I can log on with no problem and I can remotely administer the WRV54G with no problem. I can ping all of the wired and wireless W2K computers on my home LAN with no problem. However, I cannot "see", browse or map any of the shared resources on my home LAN. I have created user accounts on the home LAN computers for my laptop and router logins and I have given these accounts permissions to my shared resources, but I still cannot get to them. Linksys tech support has been absolutely no help whatsoever, even after repeated attempts.
While trying to troubleshoot this myself, I've noticed that when the Cisco VPN client is running and I'm connected to my company LAN, the IP address and subnet of my computer is changed to ones assigned by the DHCP server at my company. This seems to happen because the Cisco client activates the "Local Area Connection Number 2" on my laptop and assigns IP addresses using it. However, when I'm using the QuickVPN client to connect to my home, the IP address and subnet of my laptop continues to be those assigned by whatever local network I'm connected to (e.g. hotel, etc).
I'm wondering if the QuickVPN is supposed to be assigning an IP address and subnet to my laptop from the WRV54G's DHCP server when I connect to my home LAN. If so, could the Cisco VPN client installed on my laptop be preventing that from happening?
Sorry for the long post, but I'm at my wit's end on this one and Linksys is just no help at all.

1. The Cisco VPN client creates a virtual interface on your computer. This allows you to route traffic to the tunnel. The QuickVPN client is simpler. It only encrypts the traffic to the other end. It does not use a virtual interface. That's why you don't have another IP address when connected with QuickVPN. QuickVPN only encrypts IP packets with IPSec from your computer to 192.168.1.* (or whatever you may use on your WRV LAN) and sends them to the WRV's public IP address.
2. Microsoft Windows file sharing and LAN network browsing depends on network broadcasts. Those only work inside a LAN. If you connect from the outside to a LAN, broadcasts won't go through the VPN tunnel. This means you cannot use standard name windows workgroup name resolution to access shares. Those are propagated with broadcasts which will never go through the VPN tunnel. This means you are not able to use workgroup browsing. All you can to do access your shares is to use the IP address of the other computer.
In short:
\\mycomputer\share won't work
\\192.168.1.50\share works
(assuming the general sharing setup is O.K., i.e. you can use sharing correctly inside your LAN).
Of course, firewalls on the server end may cause problems. Access comes in from a public IP address. This may be blocked. Check the firewall logs on the server to find out if this is the case or not.
Moreover, establishing the VPN connection from a private LAN to a private LAN may not work. This is due to the double network address translation which breaks IPSec and thus the connection. If the hotel uses private IP addresses, this may be the case. But in that case you won't get ping responses from your WRV LAN.
What definitively won't work is in case when the hotel uses the same IP address subnet as you. If the hotel uses 192.168.1.* addresses and your WRV uses 192.168.1.* addresses you cannot connect. QuickVPN does only IPSec tunneling. There is no address translation in QuickVPN. Therefore connecting the identical private IP address subnet through QuickVPN will never work because all addresses exists twice, once on either side.

Router WebVPN and client certificate

Hello!
In my test lab I can't to make work my webvpn configuration =\
I have several components: MS AD, MS CS (but without NDES), router 2911 and client computer. Client and router have a certificate from MS CS. In my configuration I use authentication by certificate or aaa (LDAP) and authentication by aaa working good. But authentication by client certificate doesn't work. And my internal https services don't work also - "Invalid or no certificate", but this strange because I imported CA certificate for this.
Can you help me make it works?
My 2911 version:
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(3)T, RELEASE SOFTWARE (fc1)
My Config:
aaa authentication login webvpn group ldap local
ip local pool webvpn 192.168.200.1 192.168.200.254
bind authenticate root-dn cn=webvpn,ou=staff,dc=domain,dc=com password P@ssw0rd
webvpn gateway vpn
ip address <ip address> port 4443
ssl trustpoint root-ca
inservice
webvpn install svc flash0:/webvpn/anyconnect-dart-win-2.5.3055-k9.pkg sequence 1
webvpn context employee
ssl authenticate verify all
login-message "VPN Portal"
policy group policy1
   url-list "inside"
   functions svc-enabled
   filter tunnel VPN-SPLIT
   svc address-pool "webvpn" netmask 255.255.255.0
   svc default-domain "domain.com"
   svc keep-client-installed
   svc split dns "domain.com"
   svc split include 192.168.0.0 255.255.0.0
   svc dns-server primary 192.168.1.1
   svc dns-server secondary 192.168.1.2
   citrix enabled
virtual-template 1
default-group-policy policy1
aaa authentication list webvpn
gateway vpn
authentication certificate
username-prefill
ca trustpoint root-ca
user-profile location flash0:/userprof
inservice
crypto pki trustpoint root-ca
enrollment terminal
revocation-check none
rsakeypair root-ca
I imported certificate from pkcs12 with CA certificate.
From my debug (this is happend then i try to access to my webvpn portal and I choose my certificate from MS CS for access)
Jun 5 11:22:39: WV: validated_tp : cert_username : matched_ctx :
Jun 5 11:22:39: WV: failed to get sslvpn appinfo from opssl
Jun 5 11:22:39: WV: failed to get sslvpn appinfo from opssl
Jun 5 11:22:39: WV: Error: No certificate validated for the client
Can anybody explain me why it doesn't work?

Hi,
did you find any solution for this? As I am in it seems the same situation now.
I am testing it with Cisco 2911 - IOS version 151-3.T4 and last anyconnect client for Android (Samsung Galaxy S III mobile)
Thanx for any advice/help
Pavel

Router WRV54G Quick vpn client 1.10 ruuing on XP (remotel...

router WRV54G
Quick vpn client 1.10 ruuing on XP (remotely)
well, the client can connect to VPN router and i can verify the status online on tab vpn BUT
after 2-3 min. client receive the error message
"the gateway not responding"
AND
if client tries to ping from command prompt to the local ip addresses he find "negociating IP security"
status of router is :
- all security including firewall is disabled
- i have public IP address on Router having 255.255.255.0 subnet
- my local subnet is 10.10.1.x
please tell me what should be done
Thanks
Message Edited by SHAQ on 12-18-2007 09:26 AM

try upgrading / reflashing the firmware of the wrv54g to the latest available from www.linksys.com/download
try changing the MTU size on the client router to 1452
check whether it makes any difference

Server 2003 routing and remote access not passing VPN traffic

I've inherited a network that has two IP scopes that are routed through a Windows 2003 server with Routing and Remote Access. I can ping both sides (we'll call them HQ and Plant) internally. My firewall has an IP from the HQ IP scope and when
I connect via VPN, I can see all the devices on the HQ network including the network card that is in the routing server for that "side". However, if I'm connected via VPN, I cannot get to any of the IPs on the Plant side, not even the card
in the routing server. The buck stops on the server.
I should mention, that the firewall assigns IP addresses that are on the HQ scope, so all VPN connections will have an address from that side.
I'm lost on how to get this set up so my VPN traffic coming in from the HQ side can be routed to the Plant devices.

Hi,
To be honest, your statement confused me a bit.
VPN is used for external client get access to internal resource. When we setup VPN server, we usually have two NICs. We need choose a NIC that will be used when client initiate
a connection request. I prefer to call it external NIC card. The internal one will work as DHCP relay agent. So this is a single way connection. You cannot dial from internal to external.
If I misunderstood you, please elaborate what you are trying to do.
Hope this helps.

Routing and Remote Access VPN DHCP error

I have a strange problem.
I have a client that is using Server 2012 Standard.
On this server they have Routing and Remote Access configured for VPN client access. Their users that are working outside the office connect to the VPN to access the internal network.
The VPN works fine for the most part. Recently however, it has started having issues.
Periodically (about once every 8 days) I will hear from them that they cannot connect and that they get error 720. I will check the server and the server will have the following errors in the event log:
Warning: No IP address is available to hand out to the dial-in client.
If you check DHCP the server is running fine and will hand out local addresses but it will not hand out addresses to VPN clients. Also the addresses that it HAS previously handed out to VPN clients will not show in the address leases.
The solution strangly enough is to disconnect and reconnect a the VPN client connection that the server has connecting it to a offsite server that it does a SQL sync with.
Any ideas as to what might be causing this? If need be I can post more detailed logs but I am not sure what logs even to post or what data to collect.
Any help is greatly appreciated.

I am experiencing the same issue on a Windows 2008R2 SP1 RAS server. The above statement About increasing the lease time on DHCP does not resolve the problem.
I am also Searching for a Solutions to this issue.
Up to now I have done the Following :
1. Increased the scope/ cleared IP's in DHCP.
2. Ensure that the DHCP server is accessable.
3. Created a Manual Scope on RRAS configurations settings (then clients can connect but cannot access resources on the network). Changing Back to DHCP, you recieve the same 720 Error.
4. Stop and started the DHCP services on the DHCP Server.
5. Stop and Started RRAS Services on RRAS server.
The Only Indication is, that DHCP for some reason does not lease out Addresses to the RRAS server..

ASA 5505 as a SSL VPN Server and Easy VPN Client at the same time?

Is it possible to configure and operate the ASA 5505 as a SSL VPN server and Easy VPN Client at the same time? We would like to configure a few of these without having to purchase additional ASA 5505 and use a 2 device method (1 SSL VPN Server and 1 Easy VPN Client). Thanks in advance.

I don't think it is possible. Following links may help you
http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a008068dabe.html
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008071c428.shtml

2851 router vpn to 851 router lan clients cannot ping

Greets - I'm expanding my lab experience by adding a 2851 router to my mix of 18xx and 851/871 units. Some of this infrastructure is in production, some just lab work. I have established good connectivity between 18xx's and 851/871's with IPSEC VPNs (site-to-site static and dynamic), but my problem is with adding in a 2851.
Setup: 2851 with 12.4 ADVENTK9, WAN on GE0/0 as 216.189.223.bbb/26, LAN on GE0/1 as 172.20.0.1/20 (VPN module, but no additional HWIC modules)
851 with 12.4 ADVENTK9, WAN on FE4 as 216.53.254.aaa/24, LAN on FE0..3 via BVI1 as 172.21.1.1/24
The two router WAN ports are bridged via a 3rd router (a Zywall with 216.0.0.0/8 route, with the router at 216.1.1.1) affectionately called the "InterNOT", which provides a surrogate to the great web, minus actual other hosts and dns, but it doesn't matter. As both my WAN addresses are within 216.x.x.x, this works quite well. This surrogate has tested fine and is known to not be part of a problem.
The 851 has been tested against another 851 with complementary setup and a successful VPN can run between the two.
I have good LAN-WAN connections on each router. I do have a "Good" VPN connection between the two routers.
The problem: I cannot ping from a LAN host on 172.20.x.x on the 2851 to any 172.21.1.x (eg 172.21.1.1) host on the 851, and vice versa.
From a LAN host, I can ping to my InterNOT - for example a dhcp host 172.20.6.2 on the 2851 LAN can ping 216.1.1.1 fine. I can also ping the 851's WAN address at 216.53.254.aaa.
To complicate matters, if I connect to the routers via console, I CAN ping across the vpn to the destination LAN hosts, in both directions.
This seems to indicate that there is a bridging problem between the LAN interfaces to the VPN interfaces. I suspect this is a config problem on the 2851, as I have had a similar config working on my 851 to 851 site-to-site setups. I also suspect it is in the 2851's config as I'm still just starting out with this particular router.
So some stripped-down configs:
For the 2851:
no service config
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router2851
boot-start-marker
boot-end-marker
no logging buffered
no logging console
enable password mypassword2
no aaa new-model
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 172.20.0.1 172.20.6.1
ip dhcp excluded-address 172.20.6.254 172.20.15.254
ip dhcp pool Internal_2000
   import all
   network 172.20.0.0 255.255.240.0
   domain-name myseconddomain.int
   default-router 172.20.0.1
   lease 7
no ip domain lookup
multilink bundle-name authenticated
voice-card 0
no dspfarm
crypto pki <<truncated>>
crypto pki certificate chain TP-self-signed-2995823027
<<truncated>>
   quit
username myusername privilege 15 password 0 mypassword2
archive
log config
hidekeys
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key mysharedkey address 216.53.254.aaa
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to216.53.254.aaa
set peer 216.53.254.aaa
set transform-set ESP-3DES-SHA
match address 100
interface GigabitEthernet0/0
description $ETH-WAN$
ip address 216.189.223.bbb 255.255.255.192
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map SDM_CMAP_1
no shut
interface GigabitEthernet0/1
description $FW_INSIDE$$ETH-LAN$
ip address 172.20.0.1 255.255.240.0
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no mop enabled
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
ip http server
ip http authentication local
ip http secure-server
ip dns server
ip nat inside source route-map SDM_RMAP_1 interface GigabitEthernet0/0 overload
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 172.20.0.0 0.0.15.255
access-list 100 remark CCP_ACL Category=4
access-list 100 remark IPSec Rule
access-list 100 permit ip 172.20.0.0 0.0.15.255 172.21.1.0 0.0.0.255
access-list 101 remark CCP_ACL Category=2
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.20.0.0 0.0.15.255 172.21.1.0 0.0.0.255
access-list 101 permit ip 172.20.0.0 0.0.15.255 any
route-map SDM_RMAP_1 permit 1
match ip address 101
control-plane
banner motd ~This is a private computer system for authorized use only. And Stuff~
line con 0
line aux 0
line vty 0 4
privilege level 15
password mypassword
login local
transport input telnet ssh
scheduler allocate 20000 1000
end
And for the 851:
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router851
boot-start-marker
boot-end-marker
logging buffered 52000 debugging
no logging console
enable password mypassword
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
resource policy
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
no ip dhcp use vrf connected
ip dhcp excluded-address 172.21.1.1 172.21.1.100
ip dhcp pool Internal_2101
   import all
   network 172.21.1.0 255.255.255.0
   default-router 172.21.1.1
   domain-name mydomain.int
   dns-server 172.21.1.10
   lease 4
ip cef
ip domain name mydomain.int
ip name-server 172.21.1.10
crypto pki <<truncated>>
crypto pki certificate chain TP-self-signed-3077836316
<<truncated>>
quit
username myusername privilege 15 password 0 mypassword2
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key mysharedkey address 216.189.223.aaa
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA2 esp-3des esp-sha-hmac
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to216.189.223.bbb
set peer 216.189.223.bbb
set transform-set ESP-3DES-SHA2
match address 100
bridge irb
interface FastEthernet0
spanning-tree portfast
interface FastEthernet1
spanning-tree portfast
interface FastEthernet2
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description $ETH-WAN$
ip address 216.53.254.aaa 255.255.254.0
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
duplex auto
speed auto
no cdp enable
crypto map SDM_CMAP_1
no shut
interface Vlan1
description Internal Network
no ip address
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
description Bridge to Internal Network
ip address 172.21.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 FastEthernet4
ip route 172.21.1.0 255.255.255.0 BVI1
ip http server
ip http secure-server
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet4 overload
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 172.21.1.0 0.0.0.255
access-list 100 remark CCP_ACL Category=4
access-list 100 remark IPSec Rule
access-list 100 permit ip 172.21.1.0 0.0.0.255 172.20.0.0 0.0.15.255
access-list 101 remark CCP_ACL Category=2
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.21.1.0 0.0.0.255 172.20.0.0 0.0.15.255
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.21.1.0 0.0.0.255 172.21.101.0 0.0.0.31
access-list 101 permit ip 172.21.1.0 0.0.0.255 any
route-map SDM_RMAP_1 permit 1
match ip address 101
control-plane
bridge 1 route ip
banner motd ~This is a private computer system for authorized use only. And Stuff.~
line con 0
password mypassword
no modem enable
line aux 0
line vty 0 4
password mypassword
scheduler max-task-time 5000
end
Note that the above are somewhat stripped-down configs, without firewall or WAN ACL's - interestingly my default WAN-Inbound ACLs seem to break connectivity when included, so I realize I have some more cleanup to do there, but the 2851 LAN bridging seems to be what I should concentrate on first.
I'm still googling some of the particulars with the 2851, but any assistance is appreciated.
Regards,
Ted.

Hi,
First,please delete NAT.If we configured the NAT in the RRAS,the source IP address in all packets sent to 192.168.1.0/24 would be translated to 192.168.1.224.
Second,please enable the LAN routing in RRAS server.To enable LAN routing,please follow the steps below,
1.In the RRAS server,Open Routing and Remote Access.
2.Right-click the server name,then click
properties.
3.On the General tab,select
IPv4 Router check box,and then click Local area network(LAN) routing only.
Then,announce the 172.16.0.0 network to the router.
To learn more details about enabling LAN routing, please refer to the link below,
http://technet.microsoft.com/en-us/library/dd458974.aspx
Best Regards,
Tina

1841 ISR Router and Client VPN

Similar Messages

Maybe you are looking for