1841 SEC K9 with HWIC-2FE
Hi!
Is it possible to use the HWIC-2FE module into the 1841 SEC/K9 bundle? Using the online Cisco Dynamic config tool, HWIC-2FE is not listed as an option when you select the 1841. Does it mean that this configuration won't work? Thanks very much for your help!
Unfortunately the 1841 does not support the HWIC-2FE module. It only supports the HWIC-1FE module. See attached link for more details -
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/fe_hwic.html#wp1049748
Jon
Similar Messages
-
How many vlan can be created on single port of HWIC-2FE
Hi Guys,
I have a router 1921 with a HWIC-2FE.
How many VLAN can I create in each port of HWIC-2FE.
Thank you
SalvoI'm not sure what you are referring to. How many VLANs can be untagged while the port is in access? Or how many VLANs can you pass on a trunk?
-
HWIC-2FE fails to pass ping packets greater than 449 in slots 0,1 on 3845
When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes. It works fine up until that limit is reached, but then fails completely on a larger size packet. If we move to slot 3 or slot 4 on the 3845, the card works just fine! I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed. We're running advanced ip services 12.4(24)T7 code on the routers. We're wondering if anyone else has encountered similar problems and may know if there's a software fix or if this is a platform problem with the 3800 series. Thank you for your time.
I'd be tempted to accept your response, but it doesn't explain why the card works when moved to another slot, without making any other changes. My impression is there's some kind of hardware/asic problem with those slots in the 3845.
-
I've just rented Monsters vs Aliens on my Apple TV 3 and once we switched to default language - Russian we have experienced major lag in sound, apx. 1 sec delay with the picture. English soundtrack works fine, once we put Russian back - the delay is back. How can this be fixed? Please advise. Thank you in advance.
PS. Just bought the Monster's Inc. and Russian soundtrack works fine.Agreed! This bug with the ringtone delay (№4.1) is really annoying
-
Firefox 31, Windows 8.1, AVG, Spybot, dusabked addins ni change, used several suggestions on internet, nothing works. changed proxy settings to manual 127.0.0.1 and port as suggested - no change, could I have an NSA reroute of firefox?
Before doing anything I started Tor Browser Bundle, then exited. Started up Firefox – no 4 secs delay, very minor delay but no white page at all it seemed. Then clicked on the Open New Tab (x) and saw a white flash then the new tab – again a .5 sec delay or less before the new tab appeared.
Shutdown computer. Restarted and clicked on Fireforx shortcut. No blank white page anymore and no delay except for a very minor one.
But still had the white page flash when loading a new tab from the small x on the current page tab. Saw a white flash, then the new tab loaded. Shut down computer, restarted same problem with the new tab click on the small x - .5 sec or less white flash then tab loads.
Went into Firefox Add-Ons and disabled a number of items. Surprise no white flash on loading new tab. Decided to enable AVG PrivacyFix 5.0.11 – miracle, no white flash at all on clicking the small x on the current tab. loaded veryfast no delay there.
Will alert AVG of this issue. But still very surprised that the original main issue of having a 4 secs delay with a completly whtie screen with nothing on it except white disappeared after launching Tor Web Browser throws me for a loop.
Have not tried BlueHell yet and wonder why I should now in addition to the fact that AVG is certainly far superior to it. But if Bluehell does a better job than AdBlocker, willing to try it.
Problem appears solved – Why did Tor fix main issue? -
1841 with HWIC-AP multiple SSIDs to different subnets
Hi experts,
Please point me toward the right direction, how do I do this setup? Please give me some example? Is this different L3 BVIs along with sub interfaces on dot11radio interface assigned to different bridge-groups?
Thanks a lot.
Regards,
GPHi again,
I have managed to make it work. Just in case someone needs the same configuration within a singe Cisco1841 router.
Thanks.
dot11 ssid cisco
vlan 10
authentication open
authentication key-management wpa
wpa-psk ascii 7 05080F1C22434D000A0618
dot11 ssid cisco-guest
vlan 100
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 1511021F0725282D3B303A
bridge irb
interface Dot11Radio0/0/0
no ip address
encryption mode ciphers aes-ccm
encryption vlan 10 mode ciphers aes-ccm
encryption vlan 100 mode ciphers aes-ccm
ssid cisco
ssid cisco-guest
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root access-point
interface Dot11Radio0/0/0.10
encapsulation dot1Q 10
no cdp enable
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
interface Dot11Radio0/0/0.100
encapsulation dot1Q 100
no cdp enable
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface BVI10
ip address 10.0.0.1 255.255.255.0
interface BVI100
ip address 10.1.1.1 255.255.255.0
bridge 10 route ip
bridge 100 route ip -
Too low(400Kbyte/sec) speed with USB MSI-6545 (and printer HP-1200, sc
Hello!
I Use motherboard MSI-6545(i850, with 3 USB 1.1 ports), printer HP Laserjet-1200 and scanner HP scanjet-5400. OS Windows Xp pro SP1.
2 cables USB are length 3m.
I have found that speed of downloading from scanner to PC and from PC to printer is about 400Kbytes/sec instead of 1500Kbytes/sec. Very very slow. Why?
The support of HP X( have forwarded me to you…
Can you help me?
Andrei Shakunov, President of BusinessLawyer inc., Russia1) 3 USB 1.1
2)No
3) Sorry? no
Understanding why in Windows XP peripheral devices work in some times more slowly, than it is necessary, has encountered the strongest restriction of a bandwidth. That is USB allowed a maximum 400Кбайт/sec instead of 1.5Мбайт/sec. Especially it affects at scanning and a printing of the big graphic files.
Bought expensive firm cabels (according to a kind support HP.ru), has spent a heap of time …
At last, according to the friend has climbed in device manager in properties USB controllers (on mine i850 their two 2 sockets each). Also has been shocked by a phrase:
“ The table below shoes you how much bandwidth each USB controller is using. Each USB controller has a fixed amount of bandwidth, which all attached drivers must show ”. On the first controller – 12 %, on the second-20 %. Also it is not known how to increase them.
Who knows, how these values increase even up to 90 %? -
PVDM2-12DM compatibility with HWIC-1CE1T1-PRI
Hi there,
I'm hoping someone can assist. The setup i am trying to get working is the following
User dials in over POTS to an ISDN30 Line. The ISDN30 line (3rd Party Supplier) is connected to our 2911 via a HWIC-1CE1T1-PRI module. We have inserted a PVDM2-12DM into the router to handle the POTS call.
Problem we have is that we cannot seem to get a modem tone when the user dials in. The ISDN line connects and the debug modem command shows the modem SETUP & INIT phase - see below
Aug 13 12:58:52.341: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x1, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.341: CSM: called_number 'number removed' modem_pool 2AA6CE14 deny_call FALSE
Aug 13 12:58:52.341: CSM: Next free modem = 0/202; statbits = 10020
Aug 13 12:58:52.341: Modem 0/202 CSM: modem is allocated, modems free=-1
Aug 13 12:58:52.341: Modem 0/202 CSM: Incoming call from Unknown to 'number removed', id 0x61
Aug 13 12:58:52.341: Modem 0/202 CSM: (CSM_PROC_IDLE)<--ISDN_CALL
Aug 13 12:58:52.453: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x4, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.453: Modem 0/202 CSM: MODEM_REPORT rcvd DEV_CONNECTED for call_id 0x61
Aug 13 12:58:52.453: Modem 0/202 CSM: (CSM_PROC_MODEM_RESERVED)<--ISDN_CONNECTED
Aug 13 12:58:52.453: Modem 0/202 CSMV12: SETUP(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: Modem 0/202 CSMV12: configured for Answer(A-law) mode, with Null signaling, 0x0 tone detection
Aug 13 12:58:52.453: Modem 0/202 CSMV12: INIT(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to N/A N/A
Aug 13 12:58:52.485: CSM: csm_modem_event called
Aug 13 12:58:52.485: Modem 0/202 CSM: (CSM_PROC_WAIT_FOR_CARRIER)<--CSM_EVENT_MODEM_SETUP Aug 13 12:58:52.341: CSM:
but there is no modem tone or any more output from the debug commands.
The ISDN line is working fine as a normal ISDN dial in is successful.
Has any one tried this before or is there a known issue with this solution?Updated the IOS but made no difference. Turns out i was missing the line 'network-clock-participate wic 0' Added this to the config and managed to get incoming POTS calls. Only problem now is that the PITS call won't stay up for more than 5 seconds. Looking at the Modem AT registry settings.
-
[Cisco 1841] Being desperate with wireless config
hi guys,
I'm desperate in need of some help configuring my 1841 as a basic
access point.
First let me explain what I need it for. I need to connect my laptop,
using a wireless connection, to a device connected to one of the FE
ports.
I see the SSID in my Windows connection manager, but I can't connect
to the router. Als I think I need to set-up a route from the WIC to
one of the F! ports.
Is someone capable in sending me a basic, working config file?
Below My config file
Current configuration : 3889 bytes
! Last configuration change at 13:32:05 UTC Tue Mar 25 2008 by hwsound
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname yourname
boot-start-marker
boot-end-marker
logging buffered 52000 debugging
no aaa new-model
resource policy
ip cef
ip domain name yourdomain.com
crypto pki trustpoint TP-self-signed-2334219808
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2334219808
revocation-check none
rsakeypair TP-self-signed-2334219808
crypto pki certificate chain TP-self-signed-2334219808
certificate self-signed 01
// cut to make the message shorter //
quit
username xxx privilege 15 secret xxx
bridge irb
interface FastEthernet0/0
description $ETH-SW-LAUNCH$$INTF-INFO-FE 0$$ETH-LAN$
ip address 192.168.1.120 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
bridge-group 1
interface Dot11Radio0/0/0
no ip address
ssid HerrieWeb
vlan 1
authentication open
guest-mode
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0
36.0 48.0 54.0
station-role root
interface BVI1
ip address 192.168.10.1 255.255.255.0
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
control-plane
bridge 1 protocol ieee
bridge 1 route ip
banner login ^CCCCCCC
Cisco Router and Security Device Manager (SDM) is installed on this
device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a
privilege level of 15.
Please change these publicly known initial credentials using SDM or
the IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you
want to use.
For more information about SDM please follow the instructions in the
QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
^C
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
scheduler allocate 20000 1000
endAs Andrew said,
Add the bridge-group command to your Fast Ethernet interface. This should delete your IP address on the FE. Now your FE will be bridged to your wireless network. All IP addresses then, will be on the same subnet as your BVI interface. You will either need to assign IP addresses on the 192.168.10.0/24 statically for your hosts or you need a dhcp server on the 192.168.10.0/24 for your hosts. -
NO IPv6 on ISR with HWIC-AP???
Hi,
i just tried to enable IPv6 on of our ISRs with a wireless HWIC and found out it is NOT SUPPORTED if you use VLANS because the irb feature does not support IPv6 at all :O
anyone got an idea when CSCej50923 will be fixed?Hi,
i just tried to enable IPv6 on of our ISRs with a wireless HWIC and found out it is NOT SUPPORTED if you use VLANS because the irb feature does not support IPv6 at all :O
anyone got an idea when CSCej50923 will be fixed? -
Is 1841 router compatible with wic module U WIC -2MFT –G703 ( 2 E1 ports) ?
Hi frainds
I have cisco 1841 router
1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(3g)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
with
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
will this router supoort Uwic 2 mft-g703 card ( with 2 E1ports) ,These are the following modules supported on the 1841.
http://www.cisco.com/en/US/prod/collateral/routers/ps5853/product_data_sheet0900aecd8016a59b.html
The one you listed only works with the 1700 series which is end of life.
"If this post answers your question, please click the "Correct Answer" button" -
I am trying to get NAT working on a Cisco 2801 with HWIC-4ESW.
I have a 2801 that had a failed Fe0/1 port. The Fe0/1 port was used to give sub-interface Fe0/0.200 access to internet. We installed a HWIC-4ESW into the 2801. I have successfully moved the sub-interfaces ( 0/0.1 , 0/0.100 , and 0/0.200 ) from the Fe0/0 to the HWIC-4ESW. I have reconfigured the Fe0/0 to connect to my ISP. However, I cannot get traffic from vlan200 to pass to the internet over Fe0/0. I have a guest wireless network set for vlan 200. Clients get an IP address in the appropriate range (192.168.200.0), but they cannot get to the internet. Below I have included the results of "sh ip int brief" and some of the "sh run". I think that it is something simple, but I canot get it working.
Help would be appreciated.
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 ***.**.244.194 YES manual up up
FastEthernet0/0.200 unassigned YES unset deleted down
Service-Engine0/0 192.168.100.254 YES TFTP up up
FastEthernet0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 unassigned YES unset up up
FastEthernet0/1/1 unassigned YES unset up up
FastEthernet0/1/2 unassigned YES unset administratively down down
FastEthernet0/1/3 unassigned YES unset administratively down down
Serial0/3/0:0 unassigned YES unset down down
Serial0/3/0:1 unassigned YES unset down down
Serial0/3/0:2 unassigned YES unset down down
Serial0/3/0:3 unassigned YES unset down down
Serial0/3/0:4 unassigned YES unset down down
Serial0/3/0:5 unassigned YES unset down down
Serial0/3/0:6 unassigned YES unset down down
Serial0/3/0:7 unassigned YES unset down down
Serial0/3/0:8 unassigned YES unset down down
Serial0/3/0:9 unassigned YES unset down down
Serial0/3/0:10 unassigned YES unset down down
Serial0/3/0:11 unassigned YES unset down down
Serial0/3/0:12 unassigned YES unset down down
Serial0/3/0:13 unassigned YES unset down down
Serial0/3/0:14 unassigned YES unset down down
Serial0/3/0:15 unassigned YES unset down down
Serial0/3/0:23 unassigned YES NVRAM up up
Vlan1 192.168.1.254 YES NVRAM up up
Vlan100 192.168.100.254 YES NVRAM up up
Vlan200 192.168.200.254 YES NVRAM up up
NVI0 ***.12.244.194 YES unset administratively down down
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1 192.168.100.99
ip dhcp excluded-address 192.168.100.200 192.168.100.254
ip dhcp excluded-address 192.168.200.1 192.168.200.99
ip dhcp excluded-address 192.168.200.200 192.168.200.254
ip dhcp pool Phones
network 192.168.100.0 255.255.255.0
option 150 ip 192.168.100.254
default-router 192.168.100.254
dns-server 192.168.1.8
ip dhcp pool guestwireless
network 192.168.200.0 255.255.255.0
default-router 192.168.200.254
dns-server 8.8.8.8 8.8.4.4
ip cef
no ip domain lookup
ip domain name pwa.com
ip name-server 8.8.8.8
ip name-server 8.8.4.4
controller T1 0/3/0
pri-group timeslots 1-16,24
controller T1 0/3/1
shutdown
gw-accounting aaa
gw-accounting syslog
interface FastEthernet0/0
description Guestwireless route to internet
ip address ***.**.244.194 255.255.255.240
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface Service-Engine0/0
ip unnumbered Vlan100
service-module ip address 192.168.100.200 255.255.255.0
service-module ip default-gateway 192.168.100.254
no cdp enable
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1/0
description trunk to switch
switchport mode trunk
duplex full
speed 100
interface FastEthernet0/1/1
description voice
switchport access vlan 100
interface FastEthernet0/1/2
shutdown
interface FastEthernet0/1/3
shutdown
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn supp-service name calling
no cdp enable
interface Vlan1
description Data
ip address 192.168.1.254 255.255.255.0
interface Vlan100
description voice vlan
ip address 192.168.100.254 255.255.255.0
h323-gateway voip bind srcaddr 192.168.100.254
interface Vlan200
description Guestwireless Data
ip address 192.168.200.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:
ip nat inside source list 10 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip route 192.168.100.200 255.255.255.255 Service-Engine0/0
ip route 192.168.200.0 255.255.255.0 FastEthernet0/0
ip radius source-interface Vlan100
access-list 10 permit 192.168.200.0 0.0.0.255So, I just built this in the lab, and it seemed to work ok. I attached a sparse config, but it does let my host on the GuestWireless get the internet via NAT.
R2#sh ip nat translations vrf GuestWireless
Pro Inside global Inside local Outside local Outside global
icmp 17.12.244.194:5 192.168.200.1:5 1.1.1.1:5 1.1.1.1:5
R2#sh ip route vrf GuestWireless
Routing Table: GuestWireless
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 17.12.244.195 to network 0.0.0.0
17.0.0.0/28 is subnetted, 1 subnets
C 17.12.244.192 is directly connected, FastEthernet0/0
C 192.168.200.0/24 is directly connected, Vlan200
S* 0.0.0.0/0 [1/0] via 17.12.244.195 -
Query run in Browser 3 sec but with webpage is 60 sec
Hi,
When I run a query in the browser from the query screen, it takes 3 seconds to run. I created a webpage with only that query and blocks for conditions, exceptions. We access the webpage through the portal and it takes anywhere from 30-90 seconds to get the result.
We are on 3.5 using an ITS. Where should I start looking for the problem?
Thanks
SuzanneHi
I would start with the portal. Check the log of your request in the Portal to check how long it takes to get authentified in your BI system from the portal, and how it takes to get the data transferred from BW to the portail iview....
The issue might come from the workload on the portal
PY -
Using Cisco 1841 router with HWIC 3G Module, Now I can ping any public IP address from the router, but cant browse the internet from PC.. through Ethernet or Dor11-WiFi.
How can I get DNS address automatically, or how can can I check if its already assigned to the router!! It looks like I have only IP address in the router.... Please look at attached configuration file and update if you have any idea.Are you using your ISP DNS server or just any public DNS server? If you didn't use your ISP DNS server, try to use them. Using your own ISP DNS server should provide you with faster DNS response rather than just any public DNS server.
To find out your ISP DNS server (and other stuff), you can issue the following command on your router
show dhcp server
Make sure you are using the correct version of Cisco IOS® Software. The 3G WWAN HWIC is supported on Cisco IOS Software Release 12.4(15)T and later.
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/prod_qas0900aecd806e0563.pdf -
AP-G-A HWIC not recognized in my 1841
I am having problems with my 1841 router recognizing my HWIC-AP-G-A wireles card. I am running the following IOS: c1841-advsecurityk9-mz.124-3g.bin. I have tried placing it in slot0 and slot1. Any ideas?
Thanks!Hi Shawn,
Here is a clip from Ben's (from Cisco) excellent post (he knows ALOT more about this than I ever will :)
The HWIC-AP is supported with the 1841, but you must be running a 12.4T IOS image (in addition to the correct feature set). I'd suggest 12.4(11)T with Adv. Security or Adv. IP Services Feature Set. Make sure you meet the minimum memory requirements as well.
Your next best option would be 12.4(9)T2 with either Adv. Security or Adv. IP Services Feature Set."
Hope this helps! This should definitely work.
Rob
Maybe you are looking for
-
How can I see app updates in iOS 6
Ever since a few months ago, I have been having issues with my iOS 6 iPhone. Updating it is not an option, as it is a company device. The numeral badge appears on the App Store icon from the home screen, and from any screen inside the App Store but
-
XLR sample - sales report by item by sales rep
Hi all, I am using the above report at client site and its working great. The cust now has a requirement to modify this and include a column that looks at same period -12mths. I can easily do that by - - duplicating the existing columns - applying p
-
hi , Heads up : oracle 10g I have insert SQL script for insertion into table , It takes long time to insert into table. I have tried loading by disable indexes , but some how want to discard that process and want to narrow down on how a batch of 100
-
An error occurred while initializing Workspace. (ALC-WKS-007-049)
What is this error? It just happens randomly - on the login screen - when I try to login or when I logout. This is a big preproduction error, please elaborate on this. Thanks
-
Hello All- I would like to reference image variants within an HTML text object in my MDM repository. Something along the lines of img src="imagename.variant" Is this possible or do I need to combine the information in a custom jsp? thanks Tim