1st generation time capsule 'ambers out' with increasing frequency...

Basically the title, but it seems that after several hours, my Time Capsule (1st gen) will just amber out. I can still do things locally and I'll get a 'double NAT' warning. That's all fixed once I unplug and replug in the TC, for a while that is.Then eventually, it'll 'get tired' and just amber out with the same warning. Basically, it's fast becoming very difficult to keep a working rythym since it's constantly going down (when green, throughput is great - 5MB in from the WAN and full(ish) gigabit ethernet locally). It's on a plant ledge with plenty of air flow and it doesn't ever seem TOO hot (just warm) so I doubt it's an overheating issue, but who knows.
Anyway, who knows?
Thanks!

The Time Capsule is telling you that you do not have it configured correctly to work most effectively on your network.
Double NAT is usually an indication that you another router "upstream" from the Time Capsule....(you might call this device your "modem", but it is likely a router). This can cause network slow downs and IP address conflicts.
Both your "modem" and the Time Capsule are trying to perform routing duties. You only want one device on a network to handle the routing chores.
If you want to pursue this further, what is the make and model number of your "modem"?

Similar Messages

I want to replace my 1st generation time capsule with the new ac time capsule. What might I use the old 1st generation time capsule for

What use would there be for the 1st generation time capsule if I bought a new ac time capsule?

I just bought hte new ac time capsule (TC), and was using the 1st generation one at home.
=> I use now the old TC as an wifi extender and as a shared hard disk for family
=> the new TC is used with Time Machine for encrypted backup and first high speed network

I have a 1st generation Time Capsule with current firmware. Can I define the time periods when my children's devices have access to the wi-fi network?

I have a 1st generation Time Capsule with current firmware. Can I define the time periods when my children's devices have access to the wi-fi network?

Can I define the time periods when my children's devices have access to the wi-fi network?
Yes, using the Timed Access feature in AirPort Utility, you can setup specific rules for each wireless device which define the exact timeframe each day that the device will be allowed to connect to the wireless network.
Example....junior's iPhone can connect.....
Everyday......Between.....9 AM and 10:00 PM
or
Weekdays.......Between......4 PM and 9 PM
and Weekends.....Between......9 AM and 11 PM
At the same time, your own personal devices will have Unlimited Access at all times.

How do I get a 1st generation time capsule to join a wifi network?

OK, I've searched the groups but no luck. Here's my situation;
I'd like to configure a 1st generation time capsule to join a wifi network ideally with a printer attached to the USB. My set up is an iMac running 10.9.3, Airport Utility 6.3.2 and a 1st Generation TC with the latest firmware (7.6.4). I'm trying to connect it to an ADSL Wifi Modem/Router. I know a cabled connection would give better performance but want a wifi only connection as the printer is in a different room.
I've disabled the network functions (bridge mode) but I can only see wireless options to Create a Wireless Network, Extend a Wireless Network or Off, not to Join. If I try to extend I get the option to add an SSID, security & passwords but it doesn't seem like parameters to join -the drop-down doesn't list available networks to join & manually entering the main wifi network and password doesn't work.
Is my desired config even possible?
Dave

Something.....a Mac or PC will need to have a 5.x version of AirPort Utility installed on the computer.
Perform a factory default reset on the Time Capsule by powering it off for a few minutes. Then, hold in the reset button first and keep holding for an additional 10-12 seconds while you simultaneously plug the power back into the Time Capsule. Release the reset button after the hold period and allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
Open up AirPort Utility on the computer, select the Time Capsule and click Manual Setup
Click the Base Station tab below the row of icons to type in a device name and password that you want to use for the Time Capsule, set Time Zone, etc.
Click the Wireless tab next to the Base Station tab
Hold down the option or Alt key while you click on the Wireless Mode setting box
Select the Join a wireless network setting
Select the name of the wireless network
Enter the password for the wireless network
Verify the password
Click Update to save the settings
Note....everything here assumes that the router that provides the wireless network is using WPA2 Personal security, which is the default setting for the Time Capsule.

My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

Thanks for your response
Let me give the history - I started with an Apple Express being fed thru a D-Link EBTR 2310 cable Router from an RCA DCM315 Modem (Pure). Comcast service all the way.
Got the 1st generation TC in 2008 and merely replaced the Airport Express with the TC. Worked ok
A year or two ago I did try removing the modem and feeding the TC directly from the modem. Resulted in the same condition I have now - Continuous flashing amber on the TC. So I put the router back in the chain.
Some time later, at the recommendation of a Comcast rep, I replaced the router with (a Belkin F5D 5231) to see if speed and dropout problems would be improved. I thought it helped some at the time but now I am not so sure.
Last week I decided to see if a new modem would help with download speeds. So I got another pure cable modem (Motorola SB 6121- high on the Comcast recommended list).
Got up and running easily with Comcast help and with the modem connected directly to a computer.
Next I put the TC in the link and again could not get past the TC continuing to flash amber. Although I did get connected to the internet with this configuration I lost connection two both of my printers - one connected by USB and the other wirelessly to the TC. Again everything works fine when I put the Belkin router back in the system.
However with the router in there, the modem shows the downstream connection to be 10/100 ethernet speed. (Modem light changes color for indicating speeds.}
I have gone thru all of the combinations of powering down/ up, but all stays the same.
I can live with what I have but something still doesn’t seem right.
Thanks again

I recently upgraded my OS to Lion 10.7.4. I also just upgraded from a 1st Generation Time Capsule to a 4th Generation Time Capsule. I have an Airport Express (Version A1264) that I formerly used to extend my wireless network. AE no longer works.

I recently upgraded my OS to Lion 10.7.4. I also just upgraded from a 1st Generation Time Capsule to a 4th Generation Time Capsule. I have an Airport Express (Version A1264) that I formerly used to extend my wireless network. Airport Express no longer connects to my network. I have downloaded Airport Utility 5.6 to try and configure, but with no luck.

TC first gen was not simultaneous dual band. So.. it's probably best to factory reset your extreme and then tell it to extend again.

What type of wireless router is the 1st generation time capsule? Is it B, G or N. I'm trying to understand why our wifi signal is a bit erratic. Paul

what type of wireless router is the 1st generation time capsule? Is it B, G or N? I'm trying to establish whether its causing signal degradation as a result of conflicts with my BT Home Hub router.

The 1st generation Time Capsule is an 802.11"n" wireless router, but in default settings it produces a signal that is also compatible with "g" and "b" wireless devices.
If your HomeHub is in close proximity to the Time Capsule and it is also producing a wireless network, either the wireless on the HomeHub or the TIme Capsule should be be disabled to minimize the chances of wireless interference.
Interference may also be coming from any cordless phones you may have, or another nearby wireless network as well.

I have a 1st generation time capsule and an extreme b/g. Is the extreme slowing the network down

I have a 1st generation time capsule and an appe extreme b/g. Is the extreme slowing the network down? Should I dump it an get the new n version?

yes it is likely to be slowing down the network because you are using 802.11b/g
from what i recall with b/g a slow client can slow down the entire network to that clients speed.
this was the major improvement with 802.11n and Mimo. each client can be connected to the access point without affecting your speed to the rest of the network
its reccomended to get all new "N" equipment if you have the budget for it. some of those old airports and time capsules can still be worth something on amazon marketplace so you might be able to sell them
if you want to create / join / extend a netwowrk your going to probably need all "n" based equipment.
buy the new 4th generation time capsule or the new 5th generation airport they have better stronger radios
in the mean time configure your base station router to a high multicast rate, so it will prevent devices connecting to it at 1-2 mbps speeds and slowing down your network
if you have an apple care covered mac remember the airport / time capsule rule. all airports and time capsules purchased 2 years before you bought your mac to the 3 years of apple care covers them. if you do not have apple care then the standard warranty applies

My 1st generation Time Capsule/2007 keeps shutting off and disconnecting from internet? What could be the problem? How long do the Time Capsules usually last?

My 1st generation Time Capsule/2007 keeps shutting off and disconnecting from internet? What could be the problem? How long do the Time Capsules usually last?

That it is still working is miraclous.. most have died.. lots started flaking out at 18months to 2years..
See deadtimecapsule.org
The few that remained now seem to have reached EOL.. you can repair if you have some skills.. fairly cheaply.
But it is well and truly time to replace.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair

1st generation time capsule won't act as base station.

Yesterday I bought a used 1st generation Time Capsule (TC). I expected that it would operate as a "base station" and replace my Airport Extreme Base Station (AEBS) (in addition to it's primary function of acting as a repository for Time Machine back-ups).
But, try as I might, if I remove the AEBS from the chain the TC doesn't act as a Wi-Fi base station.
It all works just fine with both hooked together like this---FIOS/Motorola modem into the WAN port of the AEBS and an ethernet cable from AEBS (LAN) to TC (LAN).
For simplicity sake I'd like to get rid of the AEBS but once I remove it from the chain my Wi-Fi goes away (and yes I change the modem link to the WAN of the TC).
Finally, if I have to use both can I stack them or is there too much heat build up?
Thanks in advance,
JimH

The Gen1 TC is not simultaneous dual band.. Your AEBS if later model might be.
Did you power cycle the modem as well?
Did you factory reset the TC?
Plug an ethernet cable to the TC from a computer and do the setup in complete isolation to the network.. then power on the modem and see if the tc can pick up the public IP.. if it does then it should be possible to get wireless working.
But I would note.. Gen1 TC is working on borrowed time unless the power supply has been fixed or replaced.
Do not stack ever.. the TC is already over hot.. they can sit pretty close.. or you can stack in a set of wire intrays for instance.. but leave a few cm between them for air circulation... or even wall mount.

1st Generation Time Capsule reset button broke

Hello everyone I have a 1st Generation Time Capsule 500gb that I purchased used and do not have the password for AND
the reset button is BROKEN!!!
Is there anyway to reset it without the rest button working??
I bought it to upgrade it to a 2TB drive that i already own .
Thank you guys !!!!!!!

When you open the TC to replace the hard disk you will be able to press the reset. You might also be able to fix the reset lever arm.. I have found them simply forced so far back it was bent.. and no longer able to go back.. once inside the box, I can bend it back to the correct position.. but it is a plastic hinge.. and no plastic hinge likes being bent at any time.. If it has snapped right off, or snaps off attempting repair don't worry about it.. once reset, just keep it at default or write the password on a sticker and place it on the bottom.
http://www.ifixit.com/Device/Apple_Time_Capsule
Please pay attention though to Bob's comments.. fixing the power supply is going to be necessary in the near future. Especially if you put in a large drive with high start current for the hard disk. There are lots of people who find the upgrade of the hard disk is closely followed by power supply failure or it won't even start the new hard disk.. depending on type and current demand. It is much much more for some disks even if the drive has lower consumption.
If you are a DIYer it is not expensive to fix power supply or better replace it.
Although I have suggested several repair methods this is probably the cheapest.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair/cisco-adp-30rb-4pin-molex

1st generation Time capsule??

Hi,
I have searched every where but i cant find any answers and I hope you can help me:).
Does 1st generation Time Capsule have wireless connection?
Can you stream Music, Movies ect to your Ipad 3?And does it work to connect Ipad 3 to Time capsule?
Can you have any apps in Time Capsule?
Thanks and very grateful for answers!:D
Reagards//Ipad3freak

1. First generation TC has wireless.. yes. but not dual band simultaneous.. you pick either 2.4 or 5ghz.
2. A TC can store files.. it is too dumb to stream them.. if your device can pick up the file and play it, fine.. but the TC has no media server.
3. TC can store files.. no apps. It has no low level access to the firmware.
You misunderstand if you think TC is anything other than a target for time machine. It offers AFP and SMB.. and nought else.

Poor network speed with 1st generation time capsule and multiple airport express 5Ghz. My network speed slows to a crawl when not close to the time capsule. I get the range that I need, but the speed is painfully slow.

Hello,
I have a first generation time capsule running 802.11n (b/g compatable) and the airport expresse's are the newer 5ghz models. I have 3 airport express's and I have the range that I need. I can run the time capsule using 802.11n 5ghz, but I loose the range and can't connect to all of the airport express's. My computers and mobile devices run 802.11n. Does anyone have any suggestions on how to increase the network speed. Would the new airport extreme fix the problem?
Thank you

Unfortunately, you are experiencing one of the downsides to 5 GHz. That's because the higher frequency 5 GHz signals are much weaker than 2.4 GHz signals.
After all, you always have to give up something to gain something else. In the case of 5 GHz, you gain potential speed but in return, you must give up penetration power and distance capability.
In order to work well, 5 GHz signals need to almost have a line-of-sight relationship between devices. Unless you can achieve this, you will do much better to leave the Time Capsule running at the 802.11n (b/g compatible) 2.4 GHz Radio Mode and allow the Express devices to "extend" that network.
As for the location of the AirPort Express devices in an exended network, that is critical for best performance. That's because the Express can only "extend" the quality and bandwidth of the signal that it receives. Post back if you need a few more tips on how to find the best location for the AirPort Express devices.
Would the new airport extreme fix the problem?
Unfortunately, no.

IPad (4th generation) no longer connects to 1st generation time capsule

Hi all.
I am stumped. I have a 1st generation 500 MB Time Capsule to which I can successfully attach wirelessly an iPhone 4, iPhone 5, 2 MacBook Pros, a 2nd generation iPad and until recently a 4th generation iPad. I note recently because all of a sudden, for no apparent reason, I can no longer connect the iPad 4th gen. Literally one day I was connected and the next no longer. My network is hidden, WPA2 protected and MAC address controlled. When I try to connect, I get "unable to join network".
The iPad 4th gen has no problem connecting to any other WiFi network, including a current generation Time Capsule.
TC firmware is up to date. iPad iOS up to date.
What I have done so far:
Unplugged Time Capsule and after a few minutes plugged it in again. I reset the WiFi connections on the iPad via general settings. I also changed the network from hidden to not hiden and removed the password protection. When that didn't work, I reset the password and hid the network.
Any ideas??
Thanks!!!

Change both the name of the wireless network and the password
Make sure that the name of the network adheres to the following guidelines
No more than 20 characters in the name....shorter is better
Use only letters and numbers in the name....no special characters like an apostrophe, dollar sign, etc
No blank spaces in the name
Same rules for the password
Avoid the hidden network setting if possible, as it will not keep anyone that really wants to see your network from doing so, and it does make it more difficult for some devices to connect
If the iPad still will not connect, you have an iPad problem. You may need to completely restore the operating system on the iPad, or better yet, get a new iPad if it can be exchanged.
The experts over at the Ipad Support Community might have a few more tips for you. We are not iOS experts here.
Using iPad

1st generation Time Capsule - unstable internet connection

Hello,
I just bought new mac (iMac 27') and Time Capsule (1st generation firmware 7.6.3) When i connected Time Capsule instead my old router, internet connection is very tricky. When my iMac is connected by Lan cable and Wifi on mac is off , everything is fine. But when any device (iPhone, iPad) connect on wifi, internet connection becomes very unstable (including iMac on lan cable!!!). But wifi connection inside my network seems ok (i can use time capsule with no problem).
In the AirPort utility is the "pilot lamp" near the Time Capsule still green. But between Time Capsule and internet change green and amber color every 30 sec (estimate).
I tried both (2.4 and 5 GHz) WiFi but with no solution. When i use my old router, everythink is ok. Or when I unplug all WiFi devices (WiFi router on time capsule can still runs) and my iMac is connected by cable, everything is ok too.
I don't know if is it known problem, but i guess it can be hardware trouble.
Thank you for any answer
Jan

Ok, that is Gen4.
And the fault is unusual.
I recommend a full factory reset.
But downgrade the firmware first. 7.6.3 is known to be problematic. Simply hold down the option key whilst you select version in the airport utility.You can only go back to 7.6.1 though.
The quick method of factory reset.
Power down the TC.
Hold in reset. and keep holding it in. Gently it is a tiny surface mount switch with a plastic lever.. Attempting to push it out the other side of the TC will not make the switch turn on.
(I fix TC and have several reset levers bent over and jammed).
Power on the TC.. this needs three arms.. a friend or power switch you can get to with your feet..
Keep holding in reset for about 10sec until the front LED flashes rapidly.
Release reset and wait .. the boot will be slow as it deletes previous setting.. only from router side and pulls out the factory defaults.
Setup wireless and TC with short names .. no spaces and pure alphanumeric. Use different name for 5ghz.
I also recommend you install the old utility so you can access the TC log.. the new v6 utility has no log access.. so you are completely without clues as to what is happening. Not that the log is exactly helpful but it is worth a look.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0

1st generation time capsule 'ambers out' with increasing frequency...

Similar Messages

Maybe you are looking for