2.2 update causes problems when fastforwarding through streamed videos

Has any else exprienced problems when trying to fast forward or skip to later sections of a large movie file (>1 gig) that is being streamed from a shared network folder? After the 2.2 update the file often not play after FFwarding but rather continuously tries to 'load' the file - the loading bar usually gets to about 99% but never to 100%. This problem was not existent for me with the 2.1 software.

After doing a factory re-install of ATV 2.1 software (from 2.2) the streaming worked just fine again with my mac mini and router. There are reasonable seek delays but not like in 2.2 where the delay is indefinite. My iTunes library is being streamed from a USB harddrive attached to my mac mini. My LAN setup is wired so the problems I am experiencing is not due to wifi lag.
All of my files that I am attempting to stream are large, single chapter videos. I doubt it is a chapter issue, however, as even fast forwarding hangs the video playback after a few seconds of seeking.

Similar Messages

  • WRT54G ver 6. Buffering problems when viewing live streaming Video!

    Whenever my computer is connected to the computer through linksys WRT54G router, Windows Media Player do a lot of buffering. (after every 10 seconds or so). But when I connect to the internet directly through the cable modem, I don't see any buffering and I can watch the video without any problem.
    Any advice!

    I've tried most suggestions with no luck.  I've got a WRT54G v6 router with the 1.01.1 updated firmware.  Videos from MSNBC, CNN, CBS, etc... just don't want to run smoothly- and this is on a wired connection to the router.  All 3 computers hooked to router have this problem.  Choppy video or the video stops and the audio continues- or than everything pauses.  I have decent connect speeds- avg test is:
     9.66Mbps or 1.20MBytes/sec... I switched back to my old Linksys wired router and the videos played fine-connections speeds were consistent as well.  I use the wireless access for a Wii. All computers are wired into the router.  I am figuring it MUST be the router since my old router makes the problem go away...but I need the wireless access on the WRT54G for my Wii.  I did not notice if this problem was there before I upgraded the firmware since I did the upgrade when I installed the new router.  Thanks for any advice.
    RandyB

  • Automatic page updates causing problems with your screen reader? this kind of message come when i access yahoo mail.yahoo mail page not come properly.

    Automatic page updates causing problems with your screen reader? this kind of message come when i access yahoo mail.yahoo mail page not come properly.i can't chat,compose mail nothing accessing.

    Try Refresh Blocker: https://addons.mozilla.org/firefox/addon/992

  • Having a problem when scrolling through one clip: a different clip scrolls through point and time simultaneously. Can you please assist us?

    Having a problem when scrolling through one clip: a different clip scrolls through point and time simultaneously. Can you please assist us?

    First question: this is a Captivate forum, are you sure that you have a Captivate problem (with cpvc or an imported video)?

  • Automatic page updates causing problems with your screen reader

    i want to know whats going on with this Automatic page updates causing problems with your screen reader and yahoo does not work and in order for me to even email you for this question i have to use internet exp I have found this complaint many times in the forum but with no real answer how to fix the dang thing will you please tell us what your doing about this problem and or do we have to go back to using internet exp there are more sights than yahoo that no longer work with mozilla please let us no what is bieng done about this problem if any thing
    == URL of affected sites ==
    http://
    == User Agent ==
    Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SearchToolbar 1.1; Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1) ; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 3.5.30729; .NET CLR 3.0.30729; eMusic DLM/4; OfficeLiveConnector.1.4; OfficeLivePatch.1.3; InfoPath.3; .NET4.0C; AskTB5.8)

    Try Refresh Blocker: https://addons.mozilla.org/firefox/addon/992

  • Safari keeps blocking when i watch streaming videos

    Safari keeps blocking when i watch streaming videos. After 30 min it blocks the video and then all Safari is blocked with the colourful wheel turning for 2-3 minutes. What can I do? I updated flash to the latest version. It drives me nuts. I tried several links, it's not the link that is not working. HELP pls.

    The next time you have the problem, note the exact time: hour, minute, second.
    If you have more than one user account, these instructions must be carried out as an administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Scroll back in the log to the time you noted above. Select any messages timestamped from then until the end of the episode. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
    When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

  • When trying to stream video I am getting this error message "Firefox doesn't know how to open this address, because the protocol (st) isn't associated with any program." How do I fix this?

    <blockquote>Locking duplicate thread.<br>
    Please continue here: [/questions/782039]</blockquote><br>
    When trying to stream video I am getting this error message "Firefox doesn't know how to open this address, because the protocol (st) isn't associated with any program." How do I fix this?

    Protocol error usually indicates that the very leftmost part of the URL is not recognized.
    So http://, ftp://, rtsp://, usually work.
    ableton:// would need to be added by some software somewhere...
    Can you get instructions from the vendor? Does these posts seem relevant:
    [http://forum.ableton.com/viewtopic.php?f=32&t=112368 Ableton Forum • View topic - [dds&#0093; Bug with Fireforx browser and downloading project?]
    [http://forum.ableton.com/viewtopic.php?f=32&t=109918 Ableton Forum • View topic - [gck&#0093; Problem downloading shared sets from Ableton server.].

  • My iPhone keeps freezing when I am streaming videos.  It never used to do that. How do I fix this.

    My iPhone keeps freezing when I am streaming videos. How do I fix this.

    Hello Jennings Castle,
    It seems your iPhone is slowing down and not responding frequently. To rectify this issue you may want to consider performing a restore on the device, and then restoring your data from a backup via iCloud or iTunes. 
    If the issue persists after restoring your backup, you would then want to consider restoring the device and setting it up as new. Below I have linked to article which offers guidance on both of these restore methods:
    How to erase your iOS device and then set it up as a new device or restore it from backups - Apple Support
    Thank you for contributing to Apple Support Communities.
    Best,
    BobbyD

  • When I'm streaming videos from my Macbook Air to my AppleTV, my Macbook Air gets rather hot and the fan works hard and is loud trying to keep the laptop cool.  Is this harmful to the laptop?  Is this normal?

    When I'm streaming videos from my Macbook Air to my AppleTV, my Macbook Air gets rather hot and the fan works hard and is loud trying to keep the laptop cool.  Is this harmful to the laptop?  Is this normal?

    My MBA fans start running when I play video too - the CPU's video processor is working pretty hard to decode the video. The fans job is to provide better airflow.  The time to worry is when you play video and the fans don't run.

  • I deleted the 4oD app from my iPad but it still appears in the list in Settings. How do I get rid of that? It is causing problems when they issue updates as it apparently thinks I still have it when I don't.

    Can any one help me get rid of a deleted app 4oD that still appears in the Settings list. I deleted it from the home screen and Spotlight search confirms it has gone. It is causing problems because I get notified of updates and I cannot get rid of them either. I have tried re-downloading via my MacBook because there isn't a download option from the iPad (App Store clearly think I still have it when I don't) then deleting again but the listing in Settings remains.
    It is really irritating me.
    Thanks.

    Have you tried deleting the App within the Settings menu (rather than from the Home Screen)?
    Settings>General>Usage>
    From the Apps list, find the App (press "Show all Apps" if the app is not in the immediately shown list), tap on the app you wish to delete, then tap "Delete App"

  • How to keep an earlier version of AW in case update causes problems?

    I have several ideas on how to make this update less of a problem just in case I can't access older docs. Is any of these solutions workable?
    Is it possible to burn a useable CD of my current AW 6 folder in case the update to 6.2.9 doesn't work - or doesn't open older documents that my current version does open?
    Could I then run AW directly from this CD to access the older docs if they can't be opened from the update? (even though a newer version -6.2.9 - of AW would be installed in X?)
    OR can I reinstall AW 6 (into my OS 9 startup disk) from my original AW install disk to access the older versions?
    OR yet another idea, could I duplicate my current AW 6 folder and leave one AW 6 folder in the Applications (Mac OS 9) folder and move another to Applications folder in X. Then, I could do the update app in the X folder and test if the old documents still open. Then I can just delete the duplicated folder which I left in OS 9. OR will having 2 AW 6 folders cause confusion when I do the update? I assume the single user legal issue is OK with 2 AW folders on my computer for a few hours.
    Thanks for your input,
    Mrs H
    Message was edited by: Mrs H - omitted closure

    SUCCESS! THANK YOU ALL SO MUCH! (please keep reading there is a question at the end)
    AW 6.2.9 is now on my G4.
    Because of the way the Apple consultant at the Apple store set up our HDs when he installed Tiger for us, we had 2 copies already of AW 6.1. (We work from 3 external LaCie HDs)
    I only updated the 6.1 that lives in Tiger. I left the other as is at 6.1 since I know it will open the older docs that I have and need there in OS 9. And it had a translator bundled in (by Dataviz if I recall) for other formats - I'm not sure if this nice feature still exists in the update.
    The installer said it would install 6.2.8 (??) in OS 9 and 6.2.9 in OS X. But because I chose the AW 6 folder that lives in the X HD for the install, it only could access that and left the other alone.
    MY NEW QUESTION:
    The font list is quite short. I really don't use a lot of fonts, but do favour Verdana which is not in the list. Any clues on this?
    Thank you all again so much for your help with this problem,
    Mrs H

  • IOS 8.0.2 update causing problems with wifi connectivity..please help

    latest update having problems ...please help..!!!!!!!!!!

    Just a quick snapshot of my chain of events.  I’m currently on my fourth iPhone 6 Plus 64GB here in London, UK. Every time I have spoken to AppleCare and told them that I have gone through all the Wi-Fi troubleshooting methods possible they have asked me to get a brand new retail replacement as I’m within my 14 day return period.  I’ve been experiencing the following issues:
    Wi-Fi disconnects and switches to 4G (Restart required for temp fix)
    Wi-Fi is still active but there is no traffic or activity– often when in sleep mode for long periods of time.  (Toggle Wi-Fi on/off for temp fix)
    Wi-Fi disconnects and cannot find any networks (restart required for temp fix)
    This has been occurring on both iOS 8 and 8.0.2
    The issues are the same on both my 2.4Ghz and 5Ghz networks
    This is affecting my ip6+ and 5s (5s used to work perfect on ios7 on same networks) – My MBP-R and all other devices run perfectly on my network.
    I spoke to AppleCare again yesterday and asked for their advice as its now my fourth iPhone in just under a month. This time they said that apple were fully aware of the Wi-Fi problem and that new repair tickets were not being raised for their engineers as they are already working hard to get this resolved. They also said they could see all the issues raised on the apple discussions boards which they usually don’t admit too! I asked what to do next and the advisor apologised and said this is clearly a software glitch and will be resolved in the next update. I asked for a timescale but unfortunately none was given.
    As stated above I have tried all the troubleshooting methods discussed on forums and on tech websites but the only thing that gives me a stable connection without any disconnects (especially on my 6 plus) is turning cellular/mobile data off when I know I’m going to be on Wi-Fi for a sustained period of time (e.g. at home or work). I appreciate this is annoying but it’s the best temp fix until an update comes out.
    Hope it helps everyone who is having issues with their devices that have cellular functionality.
    Any comments welcome

  • Satellite Pro A120 audio problem when played through amplifier

    I've been experiencing some problems when attempting to playback music through an amplifier, using a lead from the headphone socket on my laptop connected to the amp's auxillary input: when the laptop is connected, the amp produces static, and a high-pitched hum. Weirdly, this only happens when the laptop is connected to the mains. I don't think it's a fault with my amp, as the laptop, when connected to the mains, also causes interference with the LCD screen I use with it. Is there anyway to resolve this problem? Could it be a fault with the laptop itself, or the power cable?

    Hi there,
    The possible reasons for that issue can be:
    - your machine and the amp has differrent ground potentials and/or voltage is inductioned in a mass loop
    - over the screening of the audiocable is flowing a compensation voltage betwenn the amp and the notebook
    - a low DC-voltage were generated on the resistance of the screening which causes the buzzing
    The point is that you have to ground or separate the currents of the amp and the notebook.
    Its logical: your power outlet is causing a interference so if you connnect both to to it, you have the interference.
    Check if some machines are connected to your power outlet which are needing heavily current (e.g. fan heater or what i know what) and disconnect them to see if the interference is going away.
    If not, I suggest you to try that which was suggested in your last post.
    Greets

  • Pages update causes problems?

    Since April's update I have had problems with Pages. Templates keep opening with the 'cannot find font' message even though the font is activated. Since I use Font Explorer to manage fonts I tried moving the fonts into the system folder/font folder. Pages still could not find them. After deleting Pages and Keynote and reinstalling them from my CD all is happy again.
    My impression is that the update caused the problems. Anybody else experiencing this?
    Kurt

    Hullo Kurt:
    Glad you got it sorted. Didn't think it would help you much without further insight - but I had no trouble with the update either. One of those things you had to persevere with on the system you know to fix.
    I recall that when I first installed OsX, there was a font collection called "Classic." It was not of fonts the designers call "classic", so I assume it was carried over from Os9, even though I hadn't installed that.
    You can collate whatever collections you want from Pages, as you know: just so long as they go into the User or System Library fonts. I don't know how it is with Font Explorer, but with Font Book I find the safest way of resolving duplicates so they don't keep reappearing is to "resolve duplicates" first for any black-dotted fonts, then scan for the greyed out versions where they appear. These can be safely "removed" via Font Book.
    This way Pages can choose which copy of a font it doesn't need.
    BTW I've just updated to OsX 10.4.7. Can't put it on my profile yet. But it reproduces type throughout the system, and especially in Pages, even more snappily than before, and is said to improve Font Book's handling - as well as some PDF problems.
    Be interesting to see whether those are the ones that members have had trouble with. MacFixit suggests that this system update can cause problems with various duplicate files, but I started with a clean computer, left it alone for the update, and did a Safe Boot to see what that cleaned out before I bothered with all that, and then I found no need for it. Routine maintenance did turn up quite a few permissions to be repaired though.
    OTOH, if the system details on your profile are right, you might do better to look for a combo update on Mac Downloads to be sure you get it all stitched.
    Cheers.
    Mac OsX 10.4.7, never mind what it says under here.

  • 10.5.3 Update causes problems saving to networked servers

    From the first paragraphs of an article in ComputerWorld
    Users of Adobe Systems Inc.'s popular design software, including Photoshop and InDesign, have reported that after updating their Macs to the latest version of Leopard, files get corrupted when saved to network servers.
    Apple Inc. had no immediate explanation, but a spokesman pointed to a year-old Adobe warning of potential problems when saving files to network drives.
    On Wednesday, Apple released Mac OS X 10.5.3, an update that fixed more than 100 security vulnerabilities and other problems.
    By the next morning, users were complaining on both Adobe's and Apple's support forums that files created by its CS3 suite applications -- Photoshop is the best known in the bundle -- were being corrupted.
    "Essentially, Photoshop doesn't recognize the files after saving edits on an existing X server, thus ruining your file," said a user named Kevin Moran in a message posted to an Adobe support forum Thursday.
    The complete article is at:
    http://tinyurl.com/52hn8d

    MacWorld reports the same:
    http://www.macworld.com/article/133691/2008/05/adobe.html

Maybe you are looking for

  • How to access a JS changed attribute on the server side?

    hi all; if i change an attribute on a custom component via java script on the client side. how can i access the changed value on the server side? in what method will i have the access to this changed field? thanks in advance.

  • ITunes 64 bit will not install on Windows 7 (64-Bit)

    I downloaded the 64bit version if iTunes (itunes64setup.exe), and when I went to install it, it went through most of the installation procedure and it stated that I should "download the 64 bit version of the iTunes software" (which as I said before,

  • Image engineering of windows xp with WADK 8.1 and deployed with MDT

    Hello, We know that image engineering of Windows XP with WADK 8.1 is not compatible then even if there is any ways to achieve this anyway....(by refresh scenario or any enabling setting). Thanks Richa KM

  • Channel Order from FP Get Configuration Info.vi

    Why does the get server list function of this VI return the Channels in alphabetical order instead of physical channel order 0,1,2...? The channels are also sorted in FieldPoint Explorer in this way.

  • MacBook Pro Doesn't Even Notice USB Flash Drive

    I want to get this USB Flash Drive I have to work. It's a Memorex Mini TravelDrive 2GB. It works perfectly fine on a PC, but doesn't do anything on a Mac. I tried formatting it a couple different ways, nothing. It doesn't show up in the Disk Utility.