2.3 Dual with ADC connection

A friend of mine wants me to find a Dual 2.3 Powermac G5 with an ADC video connection on ebay. Does anybody know if they made these and when?

Does anybody know if they made these
They didn't.
(50634)

Similar Messages

How to connect 22" Apple Cinema Display with ADC to Mini DisplayPort?

What are my chances to connect a 22" Apple Cinema Display with ADC connection to my new MacBook Pro with its Mini DisplayPort? Is there a combo possible of some adapter with some cable for instance?

You need a Mini DisplayPort to DVI adapter
<http://store.apple.com/be-fr/product/MB570Z/A?fnode=MTY1NDA5OQ&mco=MTEwMjYzNzQ>
followed by a DVI to ADC adapter
<http://store.apple.com/be-fr/product/M8661Z/B?fnode=MTY1NDA5OQ&mco=MTE0ODUyODQ& s=topSellers>

Hello ~ I bought a G4 Hello ~ I bought a G4 Power Mac & had used it with a standard monitor. Somebody gave me a M8536 23" Cinema Display. I think they should be compatible. My G4 seems to be missing what I think is called an ADC connection.

Should I just buy a video card with an ADC connection?

Hi Mark,
I didn't check your link on your original post. Sorry.
There is one other model that is a 400 MHz model that will accept cards with an ADC connection port.
That's the Gigabit Ethernet model.
You do not have this model Mac.
The table in the link we both have show you what video connections the and locations for those on the back panel.
Clearly, your PowerMac doesn't have an ADC connector for the card that is already installed.
So, you can conclude that you have the AGP sawtooth model that only uses VGA or DVI connection.
You can give me your PowerMac's model number to be sure.
It's located on the back panel somewhere near all of the connections.
That'll clinch, for sure, which model you do have.
You will have to purchase an ADC to DVI adapter when you decide which card to update to per JapanMac's suggestion.
The adapter doesn't affect video performance.
Just allows for a connection change at the computer.
This is about as straightforward as this gets.
The absence of an ADC connection port means you have a Mac with a VGA and/or DVI connection instead.
An adapter will be needed to use the 23 inch monitor you have with the card you have installed now or any future video card upgrade.

ADC - DVI - ADC Connection possible?

Hi Everyone,
We put one of our editing machines around to the other room to get it out of the way. In order to make the cable long enough we had to buy an ADC-DVI converter. Run it to a 15' DVI cable, to the mac, then that DVI connection back to an ADC connection on the graphic card. The monitor won't turn on. Is there something plain wrong with connecting things this way around? Any help on the topic would be mucho appreciated since we tried to upgrade to a new card and still experiencing the same problem. Perhaps some kind of incompatibility issue with stepping back and forth between the connections?
The monitors are 1 23" Studio and one 17" Studio both LCDs. They are in proper working order, and if you connect direct into the ADC port without the adapter it works. Radeon X800 Mac edition card under the hood as well.
-Colin
Power Mac G5 Mac OS X (10.4.9)

Yes. as far as I can tell, the only time any problems come up is when the ADC-DVI adapter gets thrown into the equation (although, it does work when I want to send a signal to a regular DVI monitor) its left me completely clueless and apple tech couldn't figure out what was going on. You pretty much described our set up perfectly. Seems to be quite the troubleshoot here.
-Colin
ADC port on graphics card, to ADC to DVI adapter, to
15' DVI-D or DVI-I cable, to DVI to ADC adapter (the
one with the power supply), to ADC LCD display should
work.
Does the ADC monitor work with the DVI to ADC adapter
if you plug the adapter directly into the DVI port on
the graphics card?
Power Mac G5 Mac OS X (10.4.9)

Early (Jan.04) Cinema 20" display with ADC:

Need to replace video card in G5 (Jan 04). Need video card with ADC. Any suggestions as to where to purchase this. Tried DV Warehouse already. To expensive for refurbished card. Can I get around the ADC on new video card.

The Mac Pro features one DVI-I, to which you can attach your DVI-display-with-powerbrick-in-cable, and two Mini DisplayPort.
ATI has moved forward smartly into Mini DisplayPort, nearly shortchanging users of what they call "legacy" Interfaces such as DVI, HDMI, and VGA. In order to run Three legacy Interfaces, ACTIVE (read Powered) adapters are REQUIRED.
What appears to be happening is that "the simulation of DVI" provided is a little short on power. If you don't run the ACTIVE adapters that include an additional USB for still more power, you can't run three.
Some users have reported that passive adapters used for ANY DVI displays are having sporadic trouble. The low-cost ACTIVE Adapters contain signal Drivers that use an internal power lead. The pricey Dual-Link adapters need two sets of Driver circuits, and go to an external USB cord to pick up still more power to run them.
Executive summary: There may be sporadic problems with signal levels for certain displays. If an adapter is needed, an ACTIVE DVI adapter is recommended.
If running three DVI displays, ACTIVE Adapters that also include an extra USB cord are REQUIRED.

Two servers with redundant connections for Sun StorEdge 3320 SCSI arrays

Hello All,
I read in the "Sun StorEdge 3000 Family Installation, Operation and Service Manual" that it's possible to setup "two servers with redundant connections" but I never see a detailed schema to do this. I read also the "Best Pratices Guide" but this case is not mentioned. Is it really possible ?
My objective is to split a Sun StoreEdge 3320 SCSI array between two hosts with dual redundant scsi connection.
Thanks in advance for your answers.
Francois.

At first this sounded easy, but looking at the parts listing for the 3320 seems to indicate otherwise. They're listing different part numbers for the chassis and midplane...
371-0105 chassis & midplane for JBOD
371-0106 chassis & midplane for RAID array
There are also different part numbers for the I/O boards....
370-7655 RAID SCSI I/O module
370-7713 JBOD SCSI I/O module
I can see what the difference is between the I/O modules, but am unsure of what differences if any are in the chassis and midplane. Seems like there's more involved here than what it would be worth to try and make it work. Perhaps the cost of a second HBA would be the lesser of two evils..........

Help - Need OpenGL Video Card for G4 with ADC

OK, I've got a G4 with 1.8 GHz Dual Processors. I just upgraded from FCP 5.1 to FCP 6.0 and it tells me that FCP 6.0 doesn't like my video card because it "doesn't support OpenGL." So I need a new video card - problem is, my G4 Quicksilver utilizes an Apple Flat Screen with ADC connector. I really like the Studio Display and don't want to change it. Does anyone know of a video card with "OpenGL" (that will work with FCP 6.0) that also has a ADC connector????
Thanks, Gilbert

As far as I'm aware, the Radeon 9000 is ATI's most powerful card with an ADC connector and the GeForce4 Titanium is nVidia's, although I don't think either supports Tiger's Core Image etc.
The following utility can monitor VRAM usage, which may help decide whether the 128MB version of the 9000 would be noticeably better:
http://www.macupdate.com/info.php/id/15566

Problem with JCo Connection Pool

Hi,
I have a problem with using an RFC Model in my WebApplication. So sometimes the access to the function block works, and sometimes it doesn't work. Now I know, that there is a problem with the connection pool. Look at this message:
com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool WD_X24_MODELDATA_DEST_CPIC_REKTO_DE_useDefinedUser is exhausted. The current pool size limit (max connections) is 10 connections.
So it looks like a problem with closing the JCo Connections after using. Do know where the problem is? Because I'm using many other function blocks with no problems.

Hello,
You need to increase the pool size via Visual Administrator.
Server 0 -> Services -> JCO RFC Connections.
Change the pool size from there. I believe a restart is in order.
Regards,
Jan

Problems with ipod connection.

Problems with ipod connection.
I have problems to connect my ipod to computer windows 7.
When I connect I get the following error:
"We encountered an ipod, but could not be identified correctly. Disconnect and reconnect the ipod and try again."
And it recognizes the ipod when trying to go play music or videos make me the following error:
"Error while trying to copy on disk. The device is not connected."
I've uninstalled all apple applications and re-installing, as I formatted the ipod and continues to set the same error.
What else can I do?

Hello,
While your symptoms don't exactly match the descriotion, this article may be usefull in discovering if there is a setting on your computer that is causing this to happen.
iPod not recognized in 'My Computer' and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W.

Problems with SSH: Connection Refused

Greetings fellow Arch users,
I have hit a bit of a snag that I could really use some extra help getting around. I've tried everything I can think of (and everything that Google thought might work) and I have my back rather against a wall, so I thought I'd come here to see if anyone can offer some advice.
To make a long story short, I am a college student and am attempting to set up an ssh server on a desktop at my house so I can access it remotely from the college. I have the computer set up and the server running, however I am having difficulty making connections to it from my laptop. I know that the server is running, because I can log into it both from the server itself (sshing into local host) and from my laptop when I use the internal IP address.
The server is on a static IP address within the network(192.168.0.75), and my router is configured to forward TCP port 1500 to it (I'm using 1500 as the port for my ssh server). However, when I attempt to log into the ssh server using my network's external IP address, the connection is refused. I used nmap to scan my network and found that, even though the proper ports are forwarded to the proper place as far as my Router's configuration interface is concerned, port 1500 is not listed as one of the open TCP ports. I also, to test it, temporarily disabled the firewalls on both the server and the client. That didn't help. The command that I am running is:
ssh -p 1500 douglas@[external ip address
As I am really not sure what is causing this problem, I don't know what information to provide. So here is everything that my inexperienced mind sees as likely being important. If you need anything more, let me know and I will do my best to provide it.
Here is the sshd_config file from my server.
# This is the sshd server system-wide configuration file. See
# sshd_config(5) for more information.
# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin
# The strategy used for options in the default sshd_config shipped with
# OpenSSH is to specify options with their default value where
# possible, but leave them commented. Uncommented options override the
# default value.
Port 1500
#AddressFamily any
#ListenAddress 0.0.0.0
#ListenAddress ::
# The default requires explicit activation of protocol 1
#Protocol 2
# HostKey for protocol version 1
#HostKey /etc/ssh/ssh_host_key
# HostKeys for protocol version 2
#HostKey /etc/ssh/ssh_host_rsa_key
#HostKey /etc/ssh/ssh_host_dsa_key
#HostKey /etc/ssh/ssh_host_ecdsa_key
# Lifetime and size of ephemeral version 1 server key
#KeyRegenerationInterval 1h
#ServerKeyBits 1024
# Ciphers and keying
#RekeyLimit default none
# Logging
# obsoletes QuietMode and FascistLogging
#SyslogFacility AUTH
#LogLevel INFO
# Authentication:
#LoginGraceTime 2m
PermitRootLogin no
#StrictModes yes
#MaxAuthTries 6
#MaxSessions 10
#RSAAuthentication yes
#PubkeyAuthentication yes
# The default is to check both .ssh/authorized_keys and .ssh/authorized_keys2
# but this is overridden so installations will only check .ssh/authorized_keys
AuthorizedKeysFile .ssh/authorized_keys
#AuthorizedPrincipalsFile none
#AuthorizedKeysCommand none
#AuthorizedKeysCommandUser nobody
# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts
#RhostsRSAAuthentication no
# similar for protocol version 2
#HostbasedAuthentication no
# Change to yes if you don't trust ~/.ssh/known_hosts for
# RhostsRSAAuthentication and HostbasedAuthentication
#IgnoreUserKnownHosts no
# Don't read the user's ~/.rhosts and ~/.shosts files
#IgnoreRhosts yes
# To disable tunneled clear text passwords, change to no here!
#PasswordAuthentication yes
#PermitEmptyPasswords no
# Change to no to disable s/key passwords
ChallengeResponseAuthentication no
# Kerberos options
#KerberosAuthentication no
#KerberosOrLocalPasswd yes
#KerberosTicketCleanup yes
#KerberosGetAFSToken no
# GSSAPI options
#GSSAPIAuthentication no
#GSSAPICleanupCredentials yes
# Set this to 'yes' to enable PAM authentication, account processing,
# and session processing. If this is enabled, PAM authentication will
# be allowed through the ChallengeResponseAuthentication and
# PasswordAuthentication. Depending on your PAM configuration,
# PAM authentication via ChallengeResponseAuthentication may bypass
# the setting of "PermitRootLogin without-password".
# If you just want the PAM account and session checks to run without
# PAM authentication, then enable this but set PasswordAuthentication
# and ChallengeResponseAuthentication to 'no'.
UsePAM yes
#AllowAgentForwarding yes
#AllowTcpForwarding yes
#GatewayPorts no
#X11Forwarding no
#X11DisplayOffset 10
#X11UseLocalhost yes
PrintMotd no # pam does that
#PrintLastLog yes
#TCPKeepAlive yes
#UseLogin no
UsePrivilegeSeparation sandbox # Default for new installations.
#PermitUserEnvironment no
#Compression delayed
#ClientAliveInterval 0
#ClientAliveCountMax 3
#UseDNS yes
#PidFile /run/sshd.pid
#MaxStartups 10:30:100
#PermitTunnel no
#ChrootDirectory none
#VersionAddendum none
# no default banner path
#Banner none
# override default of no subsystems
Subsystem sftp /usr/lib/ssh/sftp-server
# Example of overriding settings on a per-user basis
#Match User anoncvs
# X11Forwarding no
# AllowTcpForwarding no
# ForceCommand cvs server
The ouptut of ip addr when run on the server:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp8s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:21:9b:3a:be:94 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.75/24 brd 192.168.255.0 scope global enp8s0
valid_lft forever preferred_lft forever
inet6 fe80::221:9bff:fe3a:be94/64 scope link
valid_lft forever preferred_lft forever
Here is the output from running nmap on the network:
Starting Nmap 6.40 ( http://nmap.org ) at 2013-09-28 21:05 EDT
Initiating Ping Scan at 21:05
Scanning address [2 ports]
Completed Ping Scan at 21:05, 0.01s elapsed (1 total hosts)
Initiating Parallel DNS resolution of 1 host. at 21:05
Completed Parallel DNS resolution of 1 host. at 21:05, 0.05s elapsed
Initiating Connect Scan at 21:05
Scanning pa-addresss.dhcp.embarqhsd.net (address) [1000 ports]
Discovered open port 80/tcp on address
Discovered open port 443/tcp on address
Discovered open port 23/tcp on address
Discovered open port 21/tcp on address
Completed Connect Scan at 21:05, 4.08s elapsed (1000 total ports)
Nmap scan report for pa-address.dhcp.embarqhsd.net (address)
Host is up (0.036s latency).
Not shown: 995 closed ports
PORT STATE SERVICE
21/tcp open ftp
23/tcp open telnet
80/tcp open http
443/tcp open https
8080/tcp filtered http-proxy
Read data files from: /usr/bin/../share/nmap
Nmap done: 1 IP address (1 host up) scanned in 4.19 seconds
Here is the ssh_config client-side:
# $OpenBSD: ssh_config,v 1.27 2013/05/16 02:00:34 dtucker Exp $
# This is the ssh client system-wide configuration file. See
# ssh_config(5) for more information. This file provides defaults for
# users, and the values can be changed in per-user configuration files
# or on the command line.
# Configuration data is parsed as follows:
# 1. command line options
# 2. user-specific file
# 3. system-wide file
# Any configuration value is only changed the first time it is set.
# Thus, host-specific definitions should be at the beginning of the
# configuration file, and defaults at the end.
# Site-wide defaults for some commonly used options. For a comprehensive
# list of available options, their meanings and defaults, please see the
# ssh_config(5) man page.
# Host *
# ForwardAgent no
# ForwardX11 no
# RhostsRSAAuthentication no
# RSAAuthentication yes
# PasswordAuthentication yes
# HostbasedAuthentication no
# GSSAPIAuthentication no
# GSSAPIDelegateCredentials no
# BatchMode no
# CheckHostIP yes
# AddressFamily any
# ConnectTimeout 0
# StrictHostKeyChecking ask
# IdentityFile ~/.ssh/identity
# IdentityFile ~/.ssh/id_rsa
# IdentityFile ~/.ssh/id_dsa
# Port 22
Protocol 2
# Cipher 3des
# Ciphers aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc
# MACs hmac-md5,hmac-sha1,[email protected],hmac-ripemd160
# EscapeChar ~
# Tunnel no
# TunnelDevice any:any
# PermitLocalCommand no
# VisualHostKey no
# ProxyCommand ssh -q -W %h:%p gateway.example.com
# RekeyLimit 1G 1h
Output of ssh -v during connection attempt:
OpenSSH_6.3, OpenSSL 1.0.1e 11 Feb 2013
debug1: Reading configuration data /home/douglas/.ssh/config
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: ssh_connect: needpriv 0
debug1: Connecting to address [address] port 1500.
debug1: connect to address address port 1500: Connection refused
ssh: connect to host address port 1500: Connection refused
Thank you guys ahead of time. Getting this server operational is hardly critical, it is just a side project of mine, but I would really like to see it working.
Douglas Bahr Rumbaugh
Last edited by douglasr (2013-09-29 02:58:56)

Okay, so I finally have the opportunity to try and log in from a remote network. And. . . it doesn't work. Which is just my luck because I now need to wait an entire week, at least, before I can touch the server again. Anyway, running ssh with the maximum verbosity I get this output:
douglas ~ $ ssh -vvv -p 2000 address
OpenSSH_6.3, OpenSSL 1.0.1e 11 Feb 2013
debug1: Reading configuration data /home/douglas/.ssh/config
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: ssh_connect: needpriv 0
debug1: Connecting to address [address] port 2000.
debug1: connect to address address port 2000: Connection timed out
ssh: connect to host address port 2000: Connection timed out
It takes a minute or two for the command to finish with the connection timeout, as one would expect. And yes, I am reasonably sure that the address that I am using is my home network's external IP. It is dynamic, but I checked it before I left which was just over an hour ago. I guess that it may have changed. I'll know that for sure in the morning, when my server sends me an automatic email with the network's current address. In the meantime I am operating under the assumption that the address I am using is correct. What else could be the problem?

Not the average problem with wireless connection. Please help me..

I've been having wireless connection problems ever since I upgraded to Verizon FiOS from Verizon Wireless. Before upgrading to Verizon FiOS in the fall of 2012, my brother's laptop connected just fine with the connection. After upgrading to Verizon FiOS, my brother's laptop could not connect to the internet. It showed the wireless connection signal as Excellent, but I could not access the internet. Either it would be extremely slow or there would be no connection at all. Also, the router would sometimes restart itself randomly, and it was extremely annoying for me since I am hardwired with my desktop.
This was weird because my iPod Touch connected perfectly fine to the wifi. So I thought it must be the laptop. But I brought the laptop over to my cousin's house, who also happens to have Verizon FiOS, and the laptop connected perfectly fine. I called Verizon and none of the technicians knew what the problem was. We tried disabling and enabling the router, changing the channels, and anything that was on the list. They couldn't help me and I was extremely disappointed because not only am I not accessing the internet with my brother's laptop, but I am also paying for the service too. The last technician I called in 2012 decided to send me a new router. I hoped this would work, but it did not. This router, too, would completely reset itself numerous times before settling down and letting me use the internet.
I gave up after that. But in the spring of 2013, I got really fed up with the service I was receiving and I decided to call Verizon again. Again, Verizon tried to help me fix the laptop with their tools and solution guides. But nothing good came out of it, so I decided to ask for a technician to come to my apartment to fix it. We scheduled a day and I was pretty excited since I was almost positive that the connection for the laptop would be fine by then.
I was wrong. The technician came and only stayed for about 20 minutes. He said it must be the laptop or it must be that the walls are too thick in my apartment. But that can't be it since, in my cousin's house, the router is on the second floor and my brother was using his laptop on the first floor. So it couldn't be the laptop nor the house. So we came to no conclusion. He just attached a mini router to the laptop and hardwired it. I wasn't so content but I was glad my brother could finally use the internet now.
About three months pass by and I decide to get myself a new laptop. I get it and I am hoping the wireless connection works. It did, so I was almost positive that it was my brother's laptop that was the problem, not the wireless signal. I go on vacation for a few days and I connect perfectly fine at my friend's house. When I return home and try to connect to my wireless connection, it didn't work!
At this point, I am extremely frustrated. I decided to call Verizon again to replace my router because it was being extremely annoying. It kept resetting itself and I was tired of it. I replaced the router, and this is the router I currently have, but I STILL have the same problem. It resets itself on its own time and I hate it because I'm always in the middle of something. Wow, just wow. There is nothing they could do to help me fix this. I call up a technician, for the millionth time, and he tells me he can't access my router. This occurred with the previous technician who sent me the new router. He tells me his tools are not working and tells me he'll call me back the next day.
It was the next day and I did not receive any phone call. I am extremely disappointed in Verizon FiOS' service and it's customer service. I leave it alone and I just hardwire my laptop to the router. Of course this works, but what's the point of having a laptop when I have to keep it hardwired on my desk? After a day or two, I decide to check if the wireless connection works, and it did. I was surprised. But every now and then, it would shift on and off. Most of the time, the wireless connection is either EXREMELY SLOW or I get none at all, nonetheless, it still says the connection is Excellent.
Please, if there is anyone who could help or try to help me, I would most appreciate it. If there is more information that you need, ask me and I will try my best to provide it to you.

Admittedly, that IS a strange case. Unfortunately, it sounds like all possible troubleshooting has been done by the tech support agents. you mentioned that you were dissatisfied with your other service, did it have a similar problem? theres a possibility of dirty fiber or a bad ONT port, but the random rebooting of the router would almost exclusively be a bad router. question: is the router in the same location as before?

Cannot access to any site with ssl connection and fail to open safari and keychain, unless restart computer and login in with Guest account.

when Update to 10.7.2 ,I cannot access to any site with ssl connection and fail to open safari and keychain, unless restart computer and login in with Guest account.
OS:10.7.2
Macbook Pro 2010-mid 13inch

I also have the same problem, however if I use Firefox or Opera sites with ssl connection work fine. Still, I can't use Google Chrome (ssl), Safari (ssl), the Mac app store (generally), or the iTunes store (generally). Both the iTunes store, Safari and the app store won't respond, and Chrome displays this error: (net::ERR_TIMED_OUT). The problem persists regardless of what network I'm using. Also, when trying to access the keychain or iCloud, the process will not start (will hang). I didn't have these problems at all before updating to 10.7.2.
Sometimes rebooting helps, and sometimes not. If the problem disappears by rebooting, then it only lasts a few minutes before it reappears. It is very frustrating, especially since there doesn't seem to be any obvious or consistent way of which to fix it.
I'm also using a Macbook Pro 13-inch mid 2010.

Issues with WiFi connection to Deskjet 3545

Hi,
I have number of issues with WiFi connection to my new Deskjet 3545 AIO:
1. Printer is not able to get IP address automatically from home WiFi router (all other devices get IP with no problem). Using WPS allow printer to register in network but after switching off, WPS setting is not stored, so I have to do it again. This I was able to solve with manual entering of IP address, netwrok mask, DNS and gateway address.
2. Official HP software installed from HP site was able to find printer for 3dattempt, and it started to work. But after a while, "HP utility" program loose connection to printer, so I can not see any parameters, and I get "can not find printerä message when start to to print. After a some time (minutes to hours), whithout any action from my side, connection to printer seems to be restored, so I can see printer parameters in "HP utility" and printing is started.
3. Official HP software installed from HP site on PC (Windows 7) is not able to find printer on WiFi at all, works only with USB.
All this is disaponinting and unexpected, as my office HP LaserJet Pro 400 Color works perfect.

Hi @DmiBro,
Welcome to the HP Forums!
I see that you are having some wireless issues with your HP Deskjet 3545 to your Mac OS X 10.10 and Windows 7 computers. I am sorry to hear this, but I am happy to help!
I would recommend the following guides:
HP Single-Function and Multifunction Printers - 'Printer is offline' Message Displays on the Compute.... (The solutions for OS X v10.8 Mountain Lion and OS X v10.9 Mavericks will work on Mac OS X 10.19 Yosemite.)
HP Single-Function and Multifunction Printers - 'Printer is offline' Message Displays on the Compute....
HP ENVY 4500 and HP Deskjet Ink Advantage 3540 e-All-in-One Printer Series - Printer Does Not Mainta....
Tips for troubleshooting wireless connection issues
The following tips can help you troubleshoot and avoid wireless connectivity issues. You can try these tips separately or in combination to get a successful wireless signal.
Move the printer and the computer closer to the router, but no closer than 6 ft (1.8 m). Wireless signals can be weaker at greater distances between the printer and the router.
If you are experiencing an intermittent wireless connection, try restarting your router. Consult your router manufacturer, Internet service provider, or network administrator for instructions on how to restart the router.
Remove any metal objects between the printer, the computer, and the router. Objects such as refrigerators, microwaves, or metal bookcases can interfere with wireless transmission.
Move any device that emits radio signals, such as microwaves and cordless telephones, farther away from the printer. Such devices can interfere with wireless signals.
I would also recommend this website, HP Wireless Printing Center - Troubleshooting Issues.
Hope this information is helpful, and have a nice day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Issues with my connection when gaming (Insurgency)

Hello,
I just bought the MSI GT72 2QE. I am very pleased with de specs like the Geforce GTX 980m and the i4710hq but there is an issue that is bothering me some days now. When i am playing my beloved game Insurgency, i get ping spikes all the time. So i followed up some instruction on uninstalling the Killer software suite and just installing the drivers when i encountered the next problem. My Killer Wireless-n/a/ac 1525 Wireless Network Adapter couldn't find the drivers in the 'drivers only' package. But i did my best to find other drivers and accomplished after 5 hours full of frustration. So that is done but still doesn't solve my problem.
I don't know what to do anymore and I'm starting to think that maybe my Killer Wireless-n/a/ac 1525 Wireless Network Adapter is the issue. Maybe this is a hardware issue. I contacted the store where i bought it and they will contact me in 48 hours with a possible solution but the guy said that after all my effort it seems like a hardware issue indeed. You guys are my last hope or my laptop will be gone for 3 weeks at the factory.
Video of ping:
nl.tinypic.com/r/ztisd1/8
I hope someone has the solution.
Excuse me for my incorrect English, it's not my native language.
Bye!

Thanks for your reply.
I'm glad (and I'm not glad for the others..) that I'm not the only one. But it's not because there are more devices connected to my router because I am the only one now and I'm still having this problem while my other laptop doesn't have any problems at all. I've tried everything so far now. Resetting my router, restarting my router, reinstalled windows, reinstalled drivers, got rid of the software suite, turned off firewalls, virusscanners etc. Everything.
I thought it was only with Insurgency but it's also bugging me with Battlefield 4.
So i have tried and done everything i could find on every forum on the internet. Still I don't get the download/upload/connection I am used to when using wireless. When i am in my room, which is 10m away from the wireless router, my download speed is max 1200 kb/s where I would easily get 2300 kb/s. Also when playing online games I am having big issues with my latency/ping. It goes from 60 to 200 to 400 and back every 15/20 seconds. I also own a Asus laptop and I don't have any issues at all with the wireless connection. When I am in my room there are no problems at all. I am starting to think that the Killer Wireless adapter is just a f*cked up thing. I bought a laptop (GT72 with 980m) for €2300 but I am having all these issues with the connection. It makes me really frustrated.
Longer vid of ingame netgraph:
nl.tinypic.com/r/97mjae/8
I am hoping that there is something that solves my issues. I'm starting to think that another wireless network adapter from another brand is the only option. Is there an option to change the wireless network adapter on my laptop because I will if I can. This piece of sh*t needs to be replaced.
Bye

Issues with changing connection at run-time

Post Author: dmazourick
CA Forum: Data Connectivity and SQL
Weu2019ve tried a lot of different ways to resolve this issue, but are getting every time the different result.
Probably someone deal with that issue before and know how to correctly resolve it.
Weu2019re using Crystal Reports Runtime Components X+ (X, XI, XI R2) u2013 all of them has this issue.
We need client application to connect to multiple data sources u2013 user chooses report, chooses data source and we show the report for specified data source.
The data sources are tables or stored procedures stored in different databases on different servers.
For sure, every data source for a single report has the same structure, but that doesnu2019t matter.
The issue is: when the name of the database on one server is the same as the name of database on second server, the connection caching occurs.
How we can check that:
1.       Weu2019re running report for Server1:<DBN> - report shows data from Server1.
2.       Weu2019re opening second report for Server2:<DBN> - report shows data from Server1.
3.       Weu2019re closing application and run 1-2 in opposite order, now both reports show data from Server2.
Weu2019ve tried different approaches u2013 below is a code sample that opens the report for specific connection.
Juts to be sure that no one will ask u2013 u201CAre you sure youu2019re passing the correct connection info etc.u201D. Yes! We are sure because weu2019re trying to fix this issue for a long time and tried a lot of different approaches and still cannot find the right solution.
The code looks like below. This is VB6 code, but also the same situation was tried on VC++ 6.0
Weu2019re not looking into CR.NET solution for now.
=================================================
Sub DisplayReport(Server as String, DB as String, UID as String, PWD as String, viewer as Object)
    Dim app As New CRAXDRT.Application
    Dim report As CRAXDRT.report
    Dim database As CRAXDRT.database
    Dim table As CRAXDRT.DatabaseTable
    Dim par As CRAXDRT.ParameterFieldDefinition
    Set report = app.OpenReport("D:\TestReport_X.rpt")
    report.database.LogOnServer "pdssql.dll", Server, DB, UID, PWD
    Set table = report.database.Tables(1)
    table.SetLogOnInfo Server, DB, UID, PWD
    table.Location = table.Name
    report.database.Verify
    viewer.ReportSource = report
    viewer.ViewReport
end sub
=================================================
The result of above code is the following:
1.       If we will pass the same viewer and will use different Server u2013 the report will be displayed correctly
2.       If we will pass different viewers and will use different Server u2013 the reports will contain same data
The result of above code also depends from the version of Crystal Reports the report was designed in:
1.       For Report designed in 8.5 u2013 passing of the same viewer with same connection info second time will refresh report
2.       For Report designed in X, XI, XI R2 u2013 no refresh
Also, a slight modification of the above code helps for reports designed in XI to work properly, but not for reports designed in X and 8.5:
1.       Before calling LogonServer, make the following: DB = DB & u201C;u201D & Int(rnd()*32767)
That makes report designed in XI to display properly in different viewers, but doesnu2019t have any impact to X and no any impact to 8.5
Weu2019re really looking for any help in this question

Post Author: fburch
CA Forum: Data Connectivity and SQL
I am having similar problems and some successes.
I have 70+ reports and now suddenly I want to point them at two different servers, but at databases with the same name like you talked about.
I first just tried the following:
#1. Load report:
Dim myReport As New ReportDocument
myReport.Load(filename)
#2. Pass in parameter values
''Get the collection of parameters from the report
Dim crParameterFieldDefinitions As ParameterFieldDefinitions = r.DataDefinition.ParameterFields
''Access the specified parameter from the collection
Dim crParameter1 As ParameterFieldDefinition = crParameterFieldDefinitions.Item(ParamName)
''Get the current values from the parameter field. At this point
''there are zero values set.
'crParameter1Values = crParameter1.CurrentValues
''Set the current values for the parameter field
Dim crDiscrete1Value As New ParameterDiscreteValue
If crParameter1.ValueType = FieldValueType.DateField Or crParameter1.ValueType = FieldValueType.DateTimeField Then
If ParamValue Is System.DBNull.Value Then
crDiscrete1Value.Value = CDate("1/1/1900")
ElseIf ParamValue Is Nothing Then
crDiscrete1Value.Value = CDate("1/1/1900")
Else
crDiscrete1Value.Value = ParamValue
End If
ElseIf crParameter1.ValueType = FieldValueType.StringField Then
If ParamValue Is Nothing Then
crDiscrete1Value.Value = ""
Else
crDiscrete1Value.Value = ParamValue
End If
ElseIf crParameter1.ValueType = FieldValueType.BooleanField Then
If ParamValue Is Nothing Then
crDiscrete1Value.Value = False
ElseIf ParamValue.ToString.ToUpper = "TRUE" Then
crDiscrete1Value.Value = True
Else
crDiscrete1Value.Value = False
End If
ElseIf crParameter1.ValueType = FieldValueType.NumberField Then
If ParamValue Is Nothing Then
crDiscrete1Value.Value = 0
Else
crDiscrete1Value.Value = ParamValue
End If
Else
If ParamValue Is System.DBNull.Value Then
crDiscrete1Value.Value = Nothing
ElseIf ParamValue Is Nothing Then
crDiscrete1Value.Value = Nothing
Else
crDiscrete1Value.Value = ParamValue
End If
End If
''Add the first current value for the parameter field
Dim crParameter1Values As New ParameterValues
crParameter1Values.Add(crDiscrete1Value)
''All current parameter values must be applied for the parameter field.
crParameter1.ApplyCurrentValues(crParameter1Values)
#3 Set "Table Log in info" (most of my reports using stored procedures, but I guess I still needed this step).
Dim CrTables As Tables = r.Database.Tables
Dim CrTable As Table
Dim crtableLogoninfos As New TableLogOnInfos()
Dim crtableLogoninfo As New TableLogOnInfo()
With crConnectionInfo
.ServerName = connectionParser.GetServerName(connectionString)
.DatabaseName = connectionParser.GetDatabaseName(connectionString)
If connectionParser.DoesUseIntegratedSecurity(connectionString) = True Then
.IntegratedSecurity = True
Else
.UserID = connectionParser.GetServerUserName(connectionString)
.Password = connectionParser.GetServerPassword(connectionString)
.IntegratedSecurity = False
End If
End With
For Each CrTable In CrTables
crtableLogoninfo = CrTable.LogOnInfo
crtableLogoninfo.ConnectionInfo = crConnectionInfo
CrTable.ApplyLogOnInfo(crtableLogoninfo)
If InStr(CrTable.Location, ".dbo.") = 0 Then
CrTable.Location = crConnectionInfo.DatabaseName + ".dbo." + CrTable.Location
End If
Next
If r.Subreports.Count > 0 Then
Dim crSections As Sections
Dim crSection As Section
Dim crReportObjects As ReportObjects
Dim crReportObject As ReportObject
Dim crSubreportObject As SubreportObject
Dim crDatabase As Database
Dim subRepDoc As New ReportDocument()
'SUBREPORTS
'Set the sections collection with report sections
crSections = r.ReportDefinition.Sections
'Loop through each section and find all the report objects
'Loop through all the report objects to find all subreport objects, then set the
'logoninfo to the subreport
For Each crSection In crSections
crReportObjects = crSection.ReportObjects
For Each crReportObject In crReportObjects
If crReportObject.Kind = ReportObjectKind.SubreportObject Then
'If you find a subreport, typecast the reportobject to a subreport object
crSubreportObject = CType(crReportObject, SubreportObject)
'Open the subreport
subRepDoc = crSubreportObject.OpenSubreport(crSubreportObject.SubreportName)
crDatabase = subRepDoc.Database
CrTables = crDatabase.Tables
'Loop through each table and set the connection info
'Pass the connection info to the logoninfo object then apply the
'logoninfo to the subreport
For Each CrTable In CrTables
crtableLogoninfo = CrTable.LogOnInfo
crtableLogoninfo.ConnectionInfo = crConnectionInfo
CrTable.ApplyLogOnInfo(crtableLogoninfo)
If InStr(CrTable.Location, ".dbo.") = 0 Then
CrTable.Location = crConnectionInfo.DatabaseName + ".dbo." + CrTable.Location
End If
Next
End If
Next
Next
#4 go get the data
crv.ReportSource = myReport
crv.Refresh()
#5 Call export to disk function.
This was not changing server - did not realize it was a caching problem as you suggested. That makes sense. So anyway, then of course I threw a verify database statement on there, before I get the data. Now looks like this:
#1 Load Report
#2. Pass in parameter values (dummy values that will generate schema of table without having to actually run long running procedures, i.e. select (cast 1 as int) as somefield1, cast(2.0 as numeric(10,0)) as somefield2
#3 Set "Table Log in info"
#3b Verify the database which seems to be a necessity:
myReport.VerifyDatabase()
#3c Re-populate the report with real parameter values, same as #2 but this time with the ones that will generate the real data
#4 go get the data
#5 Call export to disk function.
This does work, some of the time. When the datasource underlying report are tables, it works. I made a dummy crystal report with lots of different types of params (stored procedure underlying database) - this also worked!
Unfortunately, when I run this against the majority of my reports, I get this stupid "invalid mapping type value", for which I have not been able to resolve yet.
I also tried putting a myreport.SetDatabaseLogon("","") -- what would this do, clear it out? (saw this referenced somewhere).
Then I tried putting the real connection info in there as well ...
myReport.SetDatabaseLogon(uid, pwd, serverName, DBname)
I put this setdatabase thing before I called verifydatabase, which is where the process is bombing out and giving me invalid mapping type for the reports that do not run.
At this point I am still working on solution. I have tried creating dummy report that used same parameter types as a report that was failing and voila - the dummy report worked. Anyway, let me know if you get your problem fixed and I will do the same. Looks like you are using a different method that I didn't notice "LogOnServer"

2.3 Dual with ADC connection

Similar Messages

Maybe you are looking for