2.45 gb usable out of 4 gb (after migrating from 32 bit windows 7 to 64 bit windows 7)
i am using windows 7 64 bit. it shows 2.45gb usable out of 4 gb . it was working fine untill i installed 32 bit windows 7 from then onwards it has started to show 2.45 gb usable out of 4gb. i formatted the disk and migrated to 64 bit but the problem
has not solved it again shows 2.45gb usable out of 4 gb.please help
HI
Ensure that your Graphic Card is not sharing the memory with RAM, It could be one reason so get it checked and if yes, the reduce the memory on BIOS for Graphic Card
Similar Messages
-
I previously downloaded the AI 30 day trial but was able to use it before the trial ran out I've since deleted it from my laptop (Windows 7 64 bit OS) How do I get it back? Trying to download AI again and getting error code 3 some thing to do with administration permissions?
If your intention is to use the trial again it will not reset if you reinstall. It will remain in its ran out state.
-
Time-out problems with RV320 (after upgrade from RV042)
config:
dual wan
WAN1: 4G router (DHCP) - approx 25Mbit/ 8Mbit
WAN2: PPOE (DSL) - 1 Mbit/ 0.2 Mbit
worked with a RV042 before and upgraded to a RV320 now.
all other things are unchanged.
3 problems - 2 solved/ not critical - one still open:
a) not critical: DHCP Status does not include all devices (changing view - but all-time problem)
I would suspect a software bug.... DHCP itself works perfectly/ IPs are assigned (just not shown in status)
b) solved (at least for now): internet connection featured time-outs; after many tries, disabling the SPI in the firewall helped
btw: this only happend for the WAN1 - WAN2 worked (or is that slow that the additonal wait time did not matter ;-)
c) very annoying: exchange connection (from Outlook client to external exchange) still has time-outs (mostly the whole mail client hangs/ ends to be restarted).
As soon as I disable WAN1, it works! But it´s not the LTE WAN itself - switching back to the RV042 does not show the same symptom.
I tried: include IP into local DNS (in general I work with google DNS servers - but changing that does not help either), opening all traffic for teh realevant IPs and disabling the firewall completely. no positive results....
thanks for any hints....I agree with you on a, probably a bug of some sort.
b is an issue I've seen before, and even on similar bandwidth (25/5) on my rv016. What was able to figure out is that the carrier (ISP) is sending about 4k/sec of ICMP packets to the router, which in turn makes the router think it's under attack so it drops the connection. As you can tell, disabling the SPI helps. For me, putting another router in front of my rv016 (on 2 of 3 wans) was my only 'permanent' solution.
c sounds like there's a protocol binding/static route in the rv042 that you need to add to the rv320. I'd check that first.
Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com -
Here is what happens: I get an add from Big Fish Games for a game that is from the Itunes store. It has a link and I click it. The link takes me directly to Itunes for about 2 seconds and then blanks out giving me:
Firefox can't find the file at itms://itunes.apple.com/us/app/haunted-manor-lord-of-mirrors/id414574468?mt=8&affC=QQABAAAAHgAJ4Q8iaTJoenF2SmlmX00tTGpZSXZoRHVRWjduUzlqUHBxUVdsUQ==.
What's up with this? This does not happen in the Chrome browser. The link works perfectly.Unfortunately I tried that and it didn't work. Thanks for the help though. I tried to uninstall and it said I couldn't because the file is corrupt or something, but I think I finally got it uninstalled and/or deleted or whatever, but now I try to reinstall/download it again from the beginning and I can't. No matter what I do I can not get Firefox working again. No matter how many times I try to redownload it. Any other suggestions?
-
Out of memory error in migrating from mysql to oracle
Hi,
I'm trying migrate from mysql to oracle9i. The hardware and software requirements are matching or even much higher than mentioned in the documentation. I have installed OMWB is properly(hope so). When I try to migrate the desired database from mysql to oracle, the repository, the Oracle model are created successfully. But while migrating data, say for around 35000 rows insertion everything works pretty fine. But after sometime, the migration stops and no error or anything appears in the screen.And in the Errorlog I get "OutOfMemoryError".
I tried to migrate single table also. But I still get this problem after sometime. The tables may contain from 10 - 130000 rows...
I even tried to change the %JRE..% memory value to 64M or 128M in the omwb.bat file and the O/s is Microsoft Windows XP, RAM 256MB.
Any help is much appreciated.
Thanks in advance.Hi Viji,
did the message in the error.log provide any extra information? For example, was the OutOfMemory error prefixed with a string
like "cannot create new native thread" ? My suggestion to workaround the problem would have been to increase the JVM heap size to 128
but this appears to have been unsuccessful for you. Can you send a mail to the Migration Workbench support services
([email protected]) explaining the problem, and attach the full error.log file please ? (please also copy me on the mail).
In the meantime, you can workaround this by migrating the schema only (there is a switch on step 3 of the migration wizard asking:
"Do you want to migrate the table data to Oracle?" - just select the "No" option). When the schema has migrated, you can then use the
offline data loading facility to migrate the data. This uses data extraction scripts and SDQL*Loader to migrate the data to the target
Oracle database.You can learn more about the offline data loading facility from the plugins referenceguide (from the Help menu in
the Migration Workbench).
I hope this helps,
Tom. -
Acrobat XI Pro "Out of Memory" error after Office 2010 install
Good Afternoon,
We recently pushed Office 2010 to our users and are now getting reports of previous installs of Adobe Acrobat XI Pro no longer working but throwing "Out of Memory" errors.
We are in a Windows XP environment. All machines are HP 8440p/6930p/6910 with the same Service pack level (3) and all up to date on security patches.
All machines are running Office 2010 SP1.
All machines have 2GB or 4GB of RAM (Only 3.25GB recognized as we are a 32bit OS environment).
All machines have adequate free space (ranging from 50gb to 200gb of free space).
All machines are set to 4096mb initial page file size with 8192mb maximum page file size.
All machines with Acrobat XI Pro *DO NOT* have Reader XI installed alongside. If Reader is installed, it is Reader 10.1 or higher.
The following troubleshooting steps have been taken:
Verify page file size (4096mb - 8192mb).
Deleted local user and Windows temp files (%temp% and c:\WINDOWS\Temp both emptied).
Repair on Adobe Acrobat XI Pro install. No change.
Uninstall Acrobat Pro XI, reboot, re-install. No change.
Uninstall Acrobat Pro XI Pro along with *ALL* other Adobe applications presently installed (Flash Player, Air), delete all Adobe folders and files found in a full search of the C drive, delete all orphaned Registry entries for all Adobe products, re-empty all temp folders, reboot.
Re-install Adobe Acrobat XI Pro. No change.
Disable enhanced security in Acrobat XI Pro. No change.
Renamed Acrobat XI's plug_ins folder to plug_ins.old.
You *can* get Acrobat to open once this is done but when you attempt to edit a file or enter data into a form, you get the message, "The "Updater" plug-in has been removed. Please re-install Acrobat to continue viewing the current file."
A repair on the Office 2010 install and re-installing Office 2010 also had no effect.
At this point, short of re-imaging the machines (which is *not* an option), we are stumped.
We have not yet tried rolling back a user to Office 2007 as the upgrade initiative is enterprise-wide and rolling back would not be considered a solution.
Anyone have any ideas beyond what has been tried so far?As mentioned, the TEMP folder is typically the problem. MS limits the size of this folder and you have 2 choices: 1. empty it or 2. increase the size limit. I am not positive this is the issue, but it does crop up at times. It does not matter how big your harddrive is, it is a matter of the amount of space that MS has allocated for virtual memory. I am surprised that there is an issue with 64GB of RAM, but MS is real good at letting you know you can't have it all for use because you might want to open up something else. That is why a lot of big packages turn off some of the limits of Windows or use Linux.
-
I have a verizon IPhone and i can't figure out how to get my ringtones from the app to iTunes, my account doesn't have a ringtone section in the liRingtone Folder?brary, how do you enable the ringtone folder?
Edit > Preferences. Select the check box for Ringtones, this will add them to the listing in iTunes.
Not sure that really answers your question though. -
Dear Apple Support Community.
As mentioned by a number of users reporting the same problem, my 2009 iMac CPU3.06 GHz Intel Core 2 Duo, 8GB RAM, has become extremely slow and repeatedly "out of Memory" since it was migrated from Mountain Lion to Mavericks (OS 10.9 then OS 10.9.1).
I have already run CleanMyMac, deleted 5GB of useless stuffs, which did not translate into any improvement. Following the advices collected in other Apple Support Community threads, I have applied EtreCheck the outcome of which is provided below.
For information, I have also upgraded my 2011 MacBook CPU2.3 GHz Core i7, 8GB which became only a bit slower than before, sometimes freezing which it almost never did before. However, I am used to the fact that Mac get usually slower and more prompt fo freeze after upgrading to a more recent OS.
Both my 2009 iMac and my 2011 MacBook have F-Secure installed. So the problem with the 2009 IMac is unlikly to be due to the presence of F-Secure. Interestingly, the few abnormalities found by Etrecheck were exacly identical before I ran CleanMyMac. There are two more findings (mentioned below) since I ran CleanMyMac on the 2009 iMac, which again didn't improve the problem.
So please find below the details of the EtreCheck experience and some additional measurements made with iStat while running EtreCheck:
Hardware Information:
iMac (24-inch, Early 2009)
iMac - model: iMac9,1
1 3.06 GHz Intel Core 2 Duo CPU: 2 cores
8 GB RAM
Video Information:
ATI Radeon HD 4850 - VRAM: 512 MB
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 1.9 - SDK 10.9
AppleAVBAudio: Version: 2.0.0 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
System Software:
OS X 10.9.1 (13B42) - Uptime: 0 days 2:40:57
Disk Information:
WDC WD1001FALS-40K1B0 disk0 : (1 TB)
EFI (disk0s1) <not mounted>: 209.7 MB
XooS5 HD (disk0s2) /: 999.35 GB (189.85 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
OPTIARC DVD RW AD-5670S
USB Information:
Apple Inc. Built-in iSight
Canon CanoScan
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
WD My Passport 071D 800mbit - 800mbit max
EFI (disk1s1) <not mounted>: 209.7 MB
disk1s2 (disk1s2) <not mounted>: 2 TB
Boot OS X (disk1s3) <not mounted>: 134.2 MB
Thunderbolt Information:
Kernel Extensions:
com.f-secure.kext.fsauth (1.0.0d1)
Problem System Launch Daemons:
[failed] com.apple.wdhelper.plist [REMARK: this abnormality appeared only after running CleanMyMac. It does not appear on my 2011 MacBook]
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[invalid] com.bjango.istatlocaldaemon.plist [REMARK: this abnormality pre-existed to running CleanMyMac. It appears also on my 2011 MacBook]
[loaded] com.f-secure.fsavd.dbhelper.plist
[loaded] com.f-secure.fsavd.plist
[loaded] com.f-secure.fsmac.firewall.plist
[loaded] com.f-secure.fsmac.fsupdated_guts2.plist
[loaded] com.f-secure.fsmac.licensetool.plist
[loaded] com.macpaw.CleanMyMac2.Agent.plist
Launch Agents:
[loaded] com.babylon.activation.plist
[loaded] com.bjango.istatlocal.plist
[loaded] com.f-secure.relauncher.plist
[loaded] com.f-secure.trasher.plist
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist
[loaded] com.google.keystone.agent.plist
[loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist
User Login Items:
iTunesHelper
Dropbox
F-Secure Anti-Virus for MAC
3rd Party Preference Panes:
Flash Player
Internet Plug-ins::
FlashPlayer-10.6: Version: 11.9.900.170 - SDK 10.6
Default Browser: Version: 537 - SDK 10.9
AdobePDFViewerNPAPI: Version: 11.0.04 - SDK 10.6
AdobePDFViewer: Version: 11.0.04 - SDK 10.6
DivXBrowserPlugin: Version: 2.1
Flash Player: Version: 11.9.900.170 - SDK 10.6
OfficeLiveBrowserPlugin: Version: 12.2.8
Google Earth Web Plug-in: Version: 6.1
QuickTime Plugin: Version: 7.7.3
iPhotoPhotocast: Version: 7.0
User Internet Plug-ins::
Picasa: Version: 1.0
Bad Fonts:
None
Old applications:
None
Time Machine:
Skip System Files: NO
Mobile backups: OFF
Auto backup: YES
Volumes being backed up:
XooS5 HD: Disk size: 930.71 GB Disk used: 753.90 GB
Destinations:
XooS5 TM [Local] (Last used)
Total size: 2
Total number of backups: 32
Oldest backup: 2013-09-15 01:11:39 +0000
Last backup: 2013-12-07 12:48:45 +0000
Size of backup disk: Too small. Backup size 2 < (Disk used 753.90 GB X 3)
Time Machine details may not be accurate. All volumes being backed up may not be listed.
REMARK: The above finding is unlikely to be accurate. In fact, my Time Machine is supported by a 2TB WD My Passport Studio external HD connected with a Firewire 800. As mentionned, only 754GB of the 2000GB are used.
Top Processes by CPU:
5% backupd
5% Mail
5% WindowServer
3% Finder
3% Dropbox
Top Processes by Memory:
1.60 GB mds_stores REMARK: this item was marked in red in the outcome of EtreCheck, so I assume there is something wrong there
82 MB Finder
74 MB Mail
49 MB softwareupdated
49 MB Dropbox
Virtual Memory Statistics:
97 MB Free RAM
1.21 GB Active RAM
1.19 GB Inactive RAM
1.21 GB Wired RAM
1.83 GB Page-ins
36 MB Page-outs
Please find now some additional measurements collected with iStat while running EtreCheck:
Practically:
The iMac can work slowly with only one software e.g. either Mail or Safari or Firefox, but still the below "out of Memory" message occurs about every 3 minutes.
Aperture has becomre to slow to be useable
If trying to write a mail (with Mail) while Safari or Firefox is open, then the "out of Memory" message occurs about every 20 seconds so I need to check on "Resume" several times per minute.
Conclusions
From the above, unless anyone in the Apple Support Community proves to be able to identify a specific problem leading to a way to find a cure, I tend to conclude that Mavericks is not suitable for computers operating with a Core 2 Duo CPU even with a 8GB of RAM.
Unless I missed something, I did not see any warning from Apple Computer Inc. informing their customers they should refrain from upgrading Core 2 Duo Computers.
The only solution I see so far is to downgrade from Mavericks to Mountain Lion. And the Apple Support Community would confirm that it is the only solution, I would appreciate to get your guidance on how to proceed.
Intended action plan
Migrate the above 2009 iMac to a 2014 Mac Mini Server operating on Mavericks to ensure that no data may be lost while downgrading to Montain Lion.
Provided the above downgrading operation is successful, assign this 2009 iMac to partial retirement e.g. Mail, Skype, iTunes and DVD player.
In advance, I would like to thank the Apple Community for helping me either i) finding a cure to the problem, ii) or confirming that Mavericks cannot operate properly on Core 2 Duo computers, iii) and in such a case, guiding me on how to downgrade to Mountain Lion.
Yours sincerely
Core... what anti-virus would you recommend using?
Use what is already included with OS X. It already includes everything it needs to protect itself from viruses and malware. Keep it that way with software updates from Apple.
A much better question is "how should I protect my Mac":
Never install any product that claims to "speed up", "clean up", "optimize", or "accelerate" your Mac. Without exception, they will do the opposite.
Never install pirated or "cracked" software, software obtained from dubious websites, or other questionable sources. Illegally obtained software is almost certain to contain malware.
Don’t supply your password in response to a popup window requesting it, unless you know what it is and the reason your credentials are required.
Don’t open email attachments from email addresses that you do not recognize, or click links contained in an email:
Most of these are scams that direct you to fraudulent sites that attempt to convince you to disclose personal information.
Such "phishing" attempts are the 21st century equivalent of a social exploit that has existed since the dawn of civilization. Don’t fall for it.
Apple will never ask you to reveal personal information in an email. If you receive an unexpected email from Apple saying your account will be closed unless you take immediate action, just ignore it. If your iTunes or App Store account becomes disabled for valid reasons, you will know when you try to buy something or log in to this support site, and are unable to.
Don’t install browser extensions unless you understand their purpose. Go to the Safari menu > Preferences > Extensions. If you see any extensions that you do not recognize or understand, simply click the Uninstall button and they will be gone.
Don’t install Java unless you are certain that you need it:
Java, a non-Apple product, is a potential vector for malware. If you are required to use Java, be mindful of that possibility.
Disable Java in Safari > Preferences > Security.
Despite its name JavaScript is unrelated to Java. No malware can infect your Mac through JavaScript. It’s OK to leave it enabled.
Block browser popups: Safari menu > Preferences > Security > and check "Block popup windows":
Popup windows are useful and required for some websites, but popups have devolved to become a common means to deliver targeted advertising that you probably do not want.
Popups themselves cannot infect your Mac, but many contain resource-hungry code that will slow down Internet browsing.
If you ever see a popup indicating it detected registry errors, that your Mac is infected with some ick, or that you won some prize, it is 100% fraudulent. Ignore it.
Ignore hyperventilating popular media outlets that thrive by promoting fear and discord with entertainment products arrogantly presented as "news". Learn what real threats actually exist and how to arm yourself against them:
The most serious threat to your data security is phishing. To date, most of these attempts have been pathetic and are easily recognized, but that is likely to change in the future as criminals become more clever.
OS X viruses do not exist, but intentionally malicious or poorly written code, created by either nefarious or inept individuals, is nothing new.
Never install something without first knowing what it is, what it does, how it works, and how to get rid of it when you don’t want it any more.
If you elect to use "anti-virus" software, familiarize yourself with its limitations and potential to cause adverse effects, and apply the principle immediately preceding this one.
Most such utilities will only slow down and destabilize your Mac while they look for viruses that do not exist, conveying no benefit whatsoever - other than to make you "feel good" about security, when you should actually be exercising sound judgment, derived from accurate knowledge, based on verifiable facts.
Do install updates from Apple as they become available. No one knows more about Macs and how to protect them than the company that builds them.
Summary: Use common sense and caution when you use your Mac, just like you would in any social context. There is no product, utility, or magic talisman that can protect you from all the evils of mankind. -
i am using numbers in the new iWork. Just bought it 10 days back. I am not able to figure out how to add serial umbers from 1 to 100( for example) also i need to freeze the top header like in windows so that we can browse down without the heading going off. Can some one help?
Hi Jay,
Be aware that "Freeze Header Rows" and "Freeze Header Columns" apply only to rows and columns that are Header rows or Header columns. You can have up to five Header rows, Five Header Columns (and five Footer rows) on a Numbers Table.
"Header rows" is a special designation. Besides being able to be frozen, Header and Footer rows are not included in formulas referencing whole columns, making it possible to place formulas such as =SUM(B) at the top (or bottom) of column B without causing a self-reference error, These designated rows are also not included in sorts of the rows in a table.
Regards,
Barry -
i have an ipod touch and i put cds on itunes onmy computer , but i cant figure out how to put the music from the cds on my ipod touch can anyone help me?
ok i select th e music from my music libary and go to file and click sync to my ipod and when it gets to step 3.. it says waiting for changes to be made.. yes the songs play on the itunes .. and no it wasnt the same computer i used last time
-
My photos are out of chronological order after the os 5 upgrade. How can I get them back in order?
My photos are out of chronological order after the os 5 upgrade. How can I get them back in order?
If its not possible, how do I go back to the old os?I had tried that several times with no luck. Late last night I was finally able to get through to the Verizon technical support who then called in Apple technical support. It took 1 1/2 hours for them to figure it out and guide me through a fix. So here's the deal .......... I use Yahoo mail and had left the "contacts" button in the on position. Apparently Yahoo likes to go into your contacts and gather information and can leave it in shambles. My advice is, go to settings, then mail, contacts, calendars. Select any and all of your email accounts and go in and turn off their access to your information. Leave it on for Icloud but none of the others.
-
System log - how to find out who has deleted the req from cube.
^hello friends
how can i find out who has deleted the request from cube ?
i wanted to check the system log , that who has deleted the request from cube .
could you please let me know how to check the same ?
regards
manojHi,
Did you try the method I had suggested. It will work.
Also its better to try the path I had suggested as it will display the logs for that particular Cube only.
But if go through SM37 > B_DEL* it will display all the logs for all the deletion jobs not just this cube and it will be difficult to find out.
Try that and you should get the log.
Thanks,
JituK -
How to fetch %ROWTYPE OUT param of a stored procedure from Java program?
I have a stored procedure that has IN / OUT parameter as table_name%ROWTYPE.
From a java program how can I access this ROWTYPE variable?
I tried all possible documentation and none of the explains whether or not this is supported.
My use case expect exactly 1 record from the procedure and we would prefer not to use REF CURSOR.
Is there a way to achieve this? If so, can someone help me with it by posting the sample code to achieve this?
I tried all the possible OracleTypes to register the OutParameter and they all fail.
Looks like there isn't any equivalent of %ROWTYPE in OracleTypes either.
If you need, I can post my sample procedure that uses %ROWTYPE as OUT parameter.
I really appreciate your help in this regard.
- KarthikHi,
If "returning only 1 record" the showstopper for not using Ref Cursor, you might want to reconsider because as you probably know, the ref cursor is only a pointer and requires additional step to retrieve the data.
Kuassi -
How do you edit out the date and time stamp from a photo
How do you edit out the date and time stamp from a photo
You can blur it out with retouch
The built-in "Retouch" brush in "Edit" mode should suffice, if the background is mostly uniform, and if you set the size of the brush to slightly wider than the bar width of the letters. For example, in this picture I removed the year from the date (in the lower right corner) by using the "retouch" brush and following the contours of the letters. (the screen shot is from iPhoto '11, but iPhoto 9 should give similar results).
Regards
Léonie -
I opened a file on my desktop that I don't remember putting there. We use many photos and I thought it was a photo file I was looking for. It turned out to be a keychain certificate from a client of ours. Does this mean that they were spying on me? What is the deal with that? Any ideas?
Interesting tid bit. I created an AAC of the original file, deleted the original MP3 from my library and also deleted the Clean matched track from the icloud.
Result is that it matched with the explicit version of Mrs. Officer this time.
What I am curious about is which songs this is happening for. I've went thru a few batched of about 500 songs at a time and redownloaded in 256k for many tracks. Sadly we don't have people to bring this to our attention and I have so much music that it's impossible to go thru every song to make sure I am getting the right version.
Maybe you are looking for
-
Cannot modify Data Connection in Infopath form as the original webservice server no longer exists
Hi, I am going to modify one of the data connections in my infopath form, but it throws me an error. The original server no longer exists. I know that I can change the manifest.xsf and replace the old server with the new server name. And when I pulle
-
Needs to be resolved ipod 5 issue
I am posting this from my computer bcuz my iPod touch 5g just wont turn on or charge. If i press the home button, th siri noise will work but the display is black, i ant put it into dfu mode, sync it with itunes, charge it with my ihome or adapter/ch
-
Issue with geeksquad repair(s)
I purchased a MacBook Air almost two years ago. Since then, it has been out for repair for 56 days (and counting). First, the hard drive crashed in 10/2013 (took one week to repair). Then, it was intermittantly overheating (03/2014), which GeekSquad
-
I need to configure an alert that will fire when a metric stops reporting. So, the metric is not at a zero value... it sometimes stops. I can'f figure out how to configure that. Thanks!
-
How do I keep older emails from being in the cloud, taking up my space?
How do I keep older e-mails out of the cloud, taking up my space?