2 AEBSn WDS setup woes/errors

I have an AEBSn and a new gigabit AEBSn, and I cannot get an internet connection through the gigabit remotes LAN cables. I have tried for 6 hours to connect them using WDS just as the manuals say. All the passwords and SSIDs are the same across both units. I have entered the MAC addresses correctly. Originally the remote would not recognize the main AEBSn, but I was able to fix that somehow. No matter what other internet settings I change (everything from DCHP to bridge mode, the remote will absolutely not provide the computer attached via LAN cable an internet connection.
I've googled it, read Apple posts, all the apple support docs and nothing is working. I am obviously missing something. Can somebody tell me what I am doing wrong?
Much thanks!

Went through steps you have above. At update, the main router no longer showed up in the airport Utility, and of course, and no luck getting internet connection through the hard wire line on the remote.
So, I started from scratch.
I ensured Both units have firmware revision 7.2.1.
I swapped base stations so that the new gigabit AEBSn will eventually be th main base station.
I disconnected every cable and turned off every WiFi client.
I hard-reset both units, and confirmed they had returned to factory defaults.
I went through the steps again…
I select the Base station that will be the main base station from the Airport status menu. I open Airport Utility, and only one router shows up - it is the one I want to configure for the main base station. I select that base station and follow the exact configuration steps for the main base station again. Upon update, I get 4 errors, (password, WiFi security, SNMP over WAN, and confi over WAN) which all make sense, because I only did the steps to make the Base station work on WDS. I corrected the errors by entering a base station password, a WPA/WPA2 personal password, deselected allow SNMP over WAN, and deselected allow configuration over Ethernet WAN port. I clicked update. Now AEBS had two errors. Ethernet not connected and internet connection, which makes sense, because it was not hooked up yet. I hook up the internet cord and test the connection. Both WiFi and wired LAN machines work great.
I select the Base station that will be the remote base station from the Airport status menu. I open Airport Utility, and only one router shows up - it is the one I want to configure for the remote base station. I select that base station and follow the exact configuration steps for the remote base station again. Upon update, I get 2 errors, (password, WiFi security) which again make sense, because I only did the steps to make the Base station work on WDS. I corrected the errors by entering the same base station password as the main, and the same WPA/WPA2 personal password as the main. I clicked update and it returns with one error – internet connection, base station does not have a valid IP address.
Per the procedures, I should be up and running with WDS - but alas, I still cannot get the remote stations LAN ports working.
It is my understanding that you need to have the same SSID in order for WDS to work. So I change the remote SSID to match the Main, and ensure that the channel matches the main’s channel and click update.
Finally both base stations show up in the AirPort Utility together. The Main now has only double NAT error, and remote returns no errors.
+** All great except… **+
+** My original problem still exists… **+
+** Nothing attached to the LAN ports of the remote base station will work. **+
In the end, the the Main station has WDS enabled, uses 802.11b/g, selected as WDS main, MAC address of remote AEBS, Connect via Ethernet, share public IP address, channel 1 and SSID of “router”. The IP address is 192.168.x.x, and the DHCP is set to 10.0.x.x. The base station itself is assigned an IP address of 10.0.x.x, and the computer attached to it via a CAT5 cable shows an IP address in the range of 10.0.x.x.
The remote base station has WDS enabled, uses 802.11b/g, selected as WDS remote, MAC address of main AEBS, Connect via WDS, bridge mode, channel 1, and SSID of “router”. The base station itself is assigned an IP address of 10.0.x.x, +* BUT *+ the computer attached to the remote base station via a CAT5 cable shows an IP address in the range of 192.168.x.x.
Hopefully this helps us figure this out, and maybe others who are having this problem (though, with my luck, it is probably just me)
Thanks again.

Similar Messages

Time Capsule WDS trial and error--working now

*{ I }*
I consider myself an expert in using Mac computers and Mac wireless systems although I am no hacker and no programmer by any stretch of the imagination (although I did teach myself how to use HyperStacks way back in 1990!). Although Apple overall provides a relative ease of use for computer technology, setting up a WDS network under b or g mode is still not always perfect. In this post, I relay my experiences of using a new Time Capsule to join an existing WDS network in 802.11g mode. It took several trials and errors and there might still be some glitches but for now it seems to be working.
note: you might want to skip to the last section roman numeral five if you want to skip the "travels with Conal and his Time Capsule" and see what my most helpful hint is.
*{ II }*
WDS stands for Wireless Distribution System which is when you use wireless routers to extend the range of your networks using a wireless method rather than linking each router by long cables. In the ideal situation, you would link the routers by cables but in a home situation one may not be able to have unsightly cables hanging everywhere.
My previous WDS system looked something like this:
DSL Modem == Extreme ~~ Express1 ~~ Express2 ## laptop
Key
== represents wired connection between routers
~~ represents wireless connection between routers
## represents wireless connection to a wireless device that is not a router (eg., laptop)
Extreme = Airport Extreme, the previous generation that looked like a saucer (or humourously I have heard called a "boob-style" station.
Express1 and Express2 = Airport Express, the previous generation that only could broadcast in b or g
My laptop usually connects to the network from Express2 because that has the strongest signal in my room.
*{ III }*
When I received my Time Capsule, I wanted to replace the existing Express2 and make Express2 simply become a wifi client (not a router) so that I can still use it for AirTunes and not to have it broadcast router signals. The reason for this is because Express2 and Time Capsule reside in the same room and aside from the redundancy of network signals, I don't know if having two wireless routers in such close proximity to each other would cause havoc on my network performance. I wanted the network to look like this schematic:
Extreme ~~ Express1 ~~ Time Capsule
I unplugged Express 2 and took it to the same location as Express 1 and Extreme 1. Then I plugged in Time Capsule. The idea of putting them in close proximity for set up was so that they could properly configure each other.
I opened up Airport Utility and it saw all four of my routers. I went through the wizard for Time Capsule selecting the option for it to replace an existing router. When all configurations were automatically set Time Capsule rebooted and in about two minutes or less, Airport Utility tells me there was an error configuring the Time Capsule. I knew immediately then that I had a few long hours ahead of me.
After that first failure I tried these various ways:
1. retried the wizard automatic way (never worked for my setup which albeit is not the simplest of network setups is neither the most complicated)
2. performed a manual configuration whereby I added the Time Capsule Airport ID to Express1 making Time Capsule a remote router of Express1; then I manually added Express1 to TimeCapsule as a router that it should connect to (that didn't work for some reason)
3. finally I got out the ethernet cable, hard reset Time Capsule, plugged in ethernet cable from laptop to TimeCapsule, and the manually added the Airport ID to Express1 and vice versa.
Note that I went through trial #2 several times fiddling around with other various WDS configuration etc. Finally what really worked for me was #3. I find that despite that I should be able to configure a new router wirelessly, I was not able to do so with success. I had to do it in a wired ethernet fashion.
After that was done, all was set. Well, almost because I still had to reconfigure Express2 so that it no longer would work as a router but as a wifi client.
*{ IV }*
Now my whole network looks like this
DSL Modem == Extreme ~~ Express1 ~~ TimeCapsule ## Express2 ## laptop
Note that Express2 and my laptop are actually both connected wirelessly to TimeCapsule. I am unable to draw it in another way due to the limitations of using linear text to represent parallel items.
*{ V }*
So, my advice for those who are having trouble with configuring Time Capsule or other wireless router, sometimes you might want to try plugging in an ethernet cable so that not only is the connection more solid but that pretty much continual contact with the router is available.
I realise that WDS in 802.11n is configured slightly differently and so perhaps WDS setup has improved but as it stands in 802.11g and 802.11b in the way Apple has implemented it, I would not suggest someone below the level of expert doing it. It can be very baffling, confusing, and irritating. I would never ask my father to try to set up WDS on his own even though there is a wizard for it. I know some people (like Chris Prillo) has had no problems with the wizard, but I have always had problems with the wizard. Not only did I have problems with it when trying to get the Time Capsule to replace an existing router, but when I set up my original WDS network I also couldn't use the wizard to set it up. It kept giving me errors.
Message was edited by: Conal Ho
Message was edited by: Conal Ho

You are over complicating things. I have a Time Capsule (TC), AirPort Extreme (AE) Base Station and AirPort Express (AX) all working flawlessly with WDS.
Make sure to write down the MAC addresses of the TC, AE, and AX. You will need them to configure WDS.
Using the AirPort Admin util configure the TC. Turn on WDS and set the TC to be the main.
Using the AirPort Admin software configure the first AX. Turn on the WDS and set it as a remote client of the TC. You will need the MAC address of the TC.
Using the AirPort Admin software configure the second AX. Turn on the WDS and set it as a remote client of the TC. You will need the MAC address of the TC.
You may have to reboot each device after each config change.
See my blog post on this at http://islandinthenet.com/2008/07/01/airport-everywhere-with-wireless-distributi on-system-wds/
Message was edited by: Khurt Williams

WDS Join Domain Error

I have WDS setup and working fine as long as the person logging into the computer to be imaged is a "Domain Admin", but if not the automatic joining of the domain fails. The user can then join the computer manually, so they do have rights. There
is something that is forcing the user to be a full Domain Admin.
I have tried putting a different security group in the registry setting but it did not make a difference:
HKLM\System\CurrentControlSet\Services\WDSServer\Providers\WDSPXE\Providers\BINLSVC\AutoApprove\<arch>\User
The computer is pre-staged and works fine for a domain admin. It all seems fine for other users, but does not join the domain.
Does anybody know how to change this?
Ryan

Hi Mr Yuan Wang,
I am having the same issue auto join domain. I am using answer file which was created through using WSIM in Win 2008 r2.
Every thing went correct except up to the point joining the domain with domain user account(salim) i got the (The username or password is incorrect) error, here is the answer file:
<?xml version="1.0" encoding="UTF-8"?>
-<unattend xmlns="urn:schemas-microsoft-com:unattend">
-<settings pass="specialize">
-<component language="neutral" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" versionScope="nonSxS" publicKeyToken="31bf3856ad364e35" processorArchitecture="amd64" name="Microsoft-Windows-Shell-Setup">
<ComputerName>PC</ComputerName>
<ProductKey>2Y4WT-DHTBF-Q6MMK-KYK6X-VKM6G</ProductKey>
<TimeZone>arab standard time</TimeZone>
<RegisteredOwner>Salin</RegisteredOwner>
<RegisteredOrganization/>
</component>
-<component language="neutral" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" versionScope="nonSxS" publicKeyToken="31bf3856ad364e35" processorArchitecture="amd64" name="Microsoft-Windows-UnattendedJoin">
-<Identification>
-<Credentials>
<Domain>bintawfik,local</Domain>
<Password>P@ssw8rd</Password>
<Username>amjad</Username>
</Credentials>
<JoinDomain>bintawfik.local</JoinDomain>
</Identification>
</component>
</settings>
-<settings pass="oobeSystem">
-<component language="neutral" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" versionScope="nonSxS" publicKeyToken="31bf3856ad364e35" processorArchitecture="amd64" name="Microsoft-Windows-International-Core">
<InputLocale>en-us</InputLocale>
<SystemLocale>en-us</SystemLocale>
<UILanguage>en-us</UILanguage>
<UILanguageFallback>en-us</UILanguageFallback>
<UserLocale>en-us</UserLocale>
</component>
-<component language="neutral" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" versionScope="nonSxS" publicKeyToken="31bf3856ad364e35" processorArchitecture="amd64" name="Microsoft-Windows-Shell-Setup">
-<AutoLogon>
-<Password>
<Value>UABAAHMAcwB3ADgAcgBkAFAAYQBzAHMAdwBvAHIAZAA=</Value>
<PlainText>false</PlainText>
</Password>
<Domain>bintawfik.local</Domain>
<Enabled>true</Enabled>
<LogonCount>99</LogonCount>
<Username>Salim</Username>
</AutoLogon>
-<OOBE>
<HideEULAPage>true</HideEULAPage>
<NetworkLocation>Work</NetworkLocation>
<ProtectYourPC>1</ProtectYourPC>
<HideWirelessSetupInOOBE>true</HideWirelessSetupInOOBE>
</OOBE>
-<UserAccounts>
-<AdministratorPassword>
<Value>UABAAHMAcwB3ADgAcgBkAEEAZABtAGkAbgBpAHMAdAByAGEAdABvAHIAUABhAHMAcwB3AG8AcgBkAA==</Value>
<PlainText>false</PlainText>
</AdministratorPassword>
-<LocalAccounts>
-<LocalAccount wcm:action="add">
-<Password>
<Value>UABAAHMAcwB3ADgAcgBkAFAAYQBzAHMAdwBvAHIAZAA=</Value>
<PlainText>false</PlainText>
</Password>
<Description>Built-in Account</Description>
<DisplayName>Admin/Power User Account</DisplayName>
<Group>Administrators</Group>
<Name>Test</Name>
</LocalAccount>
</LocalAccounts>
-<DomainAccounts>
-<DomainAccountList wcm:action="add">
<Domain>bintawfik.local</Domain>
-<DomainAccount wcm:action="add">
<Group>Domain Users</Group>
<Name>Salim</Name>
</DomainAccount>
</DomainAccountList>
</DomainAccounts>
</UserAccounts>
<TimeZone>arab standard time</TimeZone>
<RegisteredOwner>Salim</RegisteredOwner>
</component>
</settings>
<cpi:offlineImage xmlns:cpi="urn:schemas-microsoft-com:cpi" cpi:source="wim://dc1/reminst/win7custom.wim#Win7_64_Ulti"/>
</unattend>

Error during Portal Setup: An error occurred while executing a custom action:_GrantLocalPermissionsToWCSAccount

Error:
Configure Portal Setup
An error occurred while executing a custom action:_GrantLocalPermissionsToWCSAccount.11EE91AB_EABF_48A6_9973_4DCD73190AC6
This upgrade attempt has failed before permanent modifications were made. Upgrade has successfully rolled back to the original state of the system. Once the correction are made, you can retry upgrade for this role.
Errors in the Log:
MSI (s) (38:14) [21:30:36:094]: NOTE: custom action _GrantLocalPermissionsToWCSAccount.11EE91AB_EABF_48A6_9973_4DCD73190AC6 unexpectedly closed the hInstall handle (type MSIHANDLE) provided to it. The custom action should be fixed to not close that handle.
CustomAction _GrantLocalPermissionsToWCSAccount.11EE91AB_EABF_48A6_9973_4DCD73190AC6 returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
MSI (s) (38:94) [21:30:36:115]: User policy value 'DisableRollback' is 0
MSI (s) (38:14) [21:30:36:094]: NOTE: custom action _GrantLocalPermissionsToWCSAccount.11EE91AB_EABF_48A6_9973_4DCD73190AC6 unexpectedly closed the hInstall handle (type MSIHANDLE) provided to it. The custom action should be fixed to not close that handle.
CustomAction _GrantLocalPermissionsToWCSAccount.11EE91AB_EABF_48A6_9973_4DCD73190AC6 returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
MSI (s) (38:94) [21:30:36:115]: User policy value 'DisableRollback' is 0
I cannot get past this error. I am running Sharepoint Foundation 2010 with Sp1. This is on a Windows Server 2008 R2 Server +Sp1.
Any ideas?
David Baur

I finally figured this out, The issue was that I had put in the Self Service Portal Computer Name and Service account into the Service Manager SQL as SysAdmin, once I removed it flew through just fine.
David Baur

Setup Initialization Error

Mar 14, 2010 Setup Initialization Error My computer recently crashed. I got it repaired but in the process, most of my programs were lost including Adobe PhotoShop 7.0. I tried re-installing from the CD but got an error message which read: Setup Initialization Error. Setup is unable to find a hard disk location to store temporary files. Make at least 3089KB free space available and then running setup again. Error 101. Then I received another message: "Could not complete your request because of missing or invalid personalization information." Can anyone help fix this situation? Thank you. Kind personal regards,

And? What operating system? What language? What computer? User account? Sorry, such vague statemts will never get you the help you may need. This is mostly a system problem...
Mylenium

How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?

Dear all
How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?
Thanks
Regards
karan

Hello
These are the following errors
1. Trace level="1" type="T">no interface action for sender or receiver found</Trace>
2. <Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!
3.
<Trace level="1" type="T">Application Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="T">System Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
<Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!</
Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>Trace level="3" type="T">Error of the prevous version:</TraceTrace level="3" type="T">Error ID APPLICATION_ERROR</Trace>
tThere are repeating errors also.
TThanks
Regards
kkaran

"Setup initialization error" cant extract jmf !!!

Hi !!!!!!
i am a newbie here, and after searching the internet and these forums for hours, i couldn't find a solution...So please HELP ME !!!!
i had successfully installed JMF 2.1.1e earlier and it was running fine, but when i uninstall it , and again tried to re-install it, it is not even extracting !!!
the error box is:-
Setup Initialization error
"Setup is unable to run a program needed to proceed with the installation. Restart your system and try again.
Error - 105. "
please advice me what to do, its an emergency !!!!

So nobody can help me...
If there's no solution for my problem, I want to try to install an old version of JMF. Where I can findit?

Microsoft Report Viewer Redistributable 2008 setup encountered Error on Server 2008 R2 Enterprise

Hi,
I need help Microsoft Report Viewer Redistributable 2008 setup encountered Error on Server 2008 R2 Enterprise. I tried to install many time failed every
time. Please advise how I fix this issue
After click OK
Here is the next error message

This one might sort it.
http://support.microsoft.com/kb/970652
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

Setup cartridge error

I bought a new officejet pro 8600 plus and it was damaged when i mopened the box and started setting it up.
I promptly took the printer back to place of purchase but forgot to give them the setup cartridges for theat printer so they removed the cartridges from the 2nd printer.
I came back home and started again the setup process and used the cartridges from the damaged printer and now the printer will not setup, it has the 'use original setup cartridges' error
The place of purchase is now closed and i need my printer onl;ine ASAP
How do i override this error
Thanks
This question was solved.
View Solution.

This is UNACCEPTABLE! I support a user base with over 100 HP Officejet 4620 printers. I sent one user a ink cartridge pack from a dmaged printer and the printer REFUSES to use the valid cartridges?!?! This is CRIMINAL. It's a simple tank of ink and locks to a SPECIFIC printer's hardware?!?!? This is going to the BBB tonight.
And this thread as absolutely NOT solved. The orignal question from the OP has not been addressed.

Digital Fax to Folder Setup gives error message unable to establish 2-way communication with device

Digital Fax to Folder Setup gives error message unable to establish 2-way communication with device. I can s end a Fax and I can print documents. I can also, now, scan to computer. I have changed the phone line twice, restarted the router, restarted the computer, and made sure the front panel was lit when setting up the Digital Fax folder. I am on a Homegroup network, with both wireles and ethernet computers. When I view the network, it sees both computers (wireless laptop and enthernet desktop), the printer, scanner, and router (VerizonDrive). I recently had to reinstall Windows 7, where Digital Fax to Folder Setup previously worked, and now it doesn't. The network shows up as Network 3. When I try to view the network map, I get the error message that Windows cannot create the network map. Responses from other devices on the network are delayed or there is an incompatible router on the network. What am I doing wrong?

Hello @JiffyFingers and Good Afternoon
From what you have described, and from the work you did on another thread, I believe you'd get better assistance talking to either Microsoft or your router manufacturer. With not being able to create the network map, that's something a bit more intricate than digital fax setup
You can have a look at this Windows cannot create the network map. Responses from other devices on the network are delayed or th... Microsoft thread as well, and you may be able to figure it out from there.
Hope that helps, have a great day!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

SQL Server Setup failure (Error code 0x858C001B)

Hola..
Vengo con un problema que me esta causando desesperacion, ya he buscado en los hilos y no puedo solucionar este problema.
Resulta que descargue la version de SQL Server Express 2012 64 bits y al quere instalarlo me muestra el error:
SQL Server Setup has encountered the following error:
The SQL Server license agreement cannot be located for the selected edition, EXPRESS. This could be a result of corrupted media or the edition being unsupported by the media.
Error code 0x858C001B
Ya he buscado y no encuentro respuesta.
SQL Server Setup failure (Error code 0x858C001B)

Hi,
Can u have look at this Discussion
Please mark this reply as the answer or vote as helpful, as appropriate, to make it useful for other readers

Office 365 Pro Plus - Setup Failed Error - Network Deployment Share Method

Hello,
We recently deployed Office 365 Pro Plus utilizing the network share method. The issue we are experiencing is occuring after uninstalling Office 365. When we try to reinstall 365 on the same PC, the setup states "Setup Failed - A newer version
of Setup is required to install this product"
Here is our currentl XML script:
<Configuration>
<Add SourcePath=\\WDS.contoso.com\O365Deployment OfficeClientEdition="32" >
    <Product ID="O365ProPlusRetail">
      <Language ID="en-us" />
    </Product>
   </Add>
<Updates Enabled="TRUE" UpdatePath=\\WDS.contoso.com\O365Deployment />
<Display Level="FULL" AcceptEULA="TRUE" />


</Configuration>
Any help would be greatly appreciated!

Hi,
Would you like to give me the whole error message? Please see the "Troubleshoot specific errors in Office 365 ProPlus",we can find the resolution of
Internet Connection Required.
Since you want to install or deploy the Office 365 pro plus, please read the following articles and check they are helpful.
http://technet.microsoft.com/en-us/library/gg715562(v=office.15).aspx
http://blogs.technet.com/b/office_resource_kit/archive/2013/08/08/how-to-deploy-office-365-proplus-from-an-on-premises-web-portal.aspx
http://www.microsoftvirtualacademy.com/training-courses/office-365-deployment-for-it-pros
http://community.office365.com/en-us/w/upgrade/installing-office-365-proplus-with-the-office-deployment-tool.aspx
Regards,
George Zhao
TechNet Community Support

WDS Client throwing error 0x80070570 every time it trying to deploy OS.

HI
I have WDS and DHCP on subnet A and Clients on Subnet B. DHCP has server options of 66 set to wds server IP Address and 67 set to \boot\x64\wdsnbp.com. I have not setup option 60.
When i try to boot a client from WDS it get ip address and starts to format but in midway when it says expanding windows files it throws up error 0x80070570 and installation fails. I have tried to re import the image and also deleted the image group and
recreated it. Still have this issue.
Any help would be appreciated.

Hi,
Actually, that would be a different question and really out of the forum. Just some explaination here:
DHCP protocol is used during the communications between client and WDS server. But as we know, we cannot receive a DHCP broadcast from another subnet or VLAN by default. So we need IP helper here to forward DHCP broadcast.
About the setting you can need refer to network device manufacture. Since you have two subnets, there must be a router or switch. Another workaround is just to put WDS and DHCP server into the same subnet with the clients.

[Error] Microsoft SQL Server 2008 Setup. Error reading from file msdbdata.mdf

Hi all
I'm trying to install SQL 2008 Express on my Computer: Hp compact DX7300 Slim tower.
and get this error:
TITLE: Microsoft SQL Server 2008 Setup
The following error has occurred:Error reading from file d:\8268cd7b247d294de359c9\x86\setup\sql_engine_core_inst_msi\PFiles\SqlServr\MSSQL.X\MSSQL\Binn\Template\msdbdata.mdf. Verify that the file exists and that you can access it.
Click 'Retry' to retry the failed action, or click 'Cancel' to cancel this action and continue setup.
For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.0.1823.0&EvtType=0xF45F6601%25401201%25401
Log file
Overall summary:
Final result: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup.
Exit code (Decimal): -2068643839
Exit facility code: 1203
Exit error code: 1
Exit message: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup.
Start time: 2014-12-09 23:22:03
End time: 2014-12-09 23:40:28
Requested action: Install
Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20141209_232121\sql_engine_core_inst_Cpu32_1.log
Exception help link: http://go.microsoft.com/fwlink?LinkId=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.0.1823.0
Machine Properties:
Machine name: VISTA-PC
Machine processor count: 2
OS version: Windows Vista
OS service pack: Service Pack 1
OS region: United States
OS language: English (United States)
OS architecture: x86
Process architecture: 32 Bit
OS clustered: No
Product features discovered:
Product Instance Instance ID Feature
Language Edition Version Clustered
Package properties:
Description: SQL Server Database Services 2008
SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9}
ProductName: SQL2008
Type: RTM
Version: 10
SPLevel: 0
Installation location: d:\8268cd7b247d294de359c9\x86\setup\
Installation edition: EXPRESS
User Input Settings:
ACTION: Install
ADDCURRENTUSERASSQLADMIN: False
AGTSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE
AGTSVCPASSWORD: *****
AGTSVCSTARTUPTYPE: Disabled
ASBACKUPDIR: Backup
ASCOLLATION: Latin1_General_CI_AS
ASCONFIGDIR: Config
ASDATADIR: Data
ASDOMAINGROUP: <empty>
ASLOGDIR: Log
ASPROVIDERMSOLAP: 1
ASSVCACCOUNT: <empty>
ASSVCPASSWORD: *****
ASSVCSTARTUPTYPE: Automatic
ASSYSADMINACCOUNTS: <empty>
ASTEMPDIR: Temp
BROWSERSVCSTARTUPTYPE: Disabled
CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20141209_232121\ConfigurationFile.ini
ENABLERANU: True
ERRORREPORTING: False
FEATURES: SQLENGINE,REPLICATION
FILESTREAMLEVEL: 0
FILESTREAMSHARENAME: <empty>
FTSVCACCOUNT: <empty>
FTSVCPASSWORD: *****
HELP: False
INDICATEPROGRESS: False
INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL Server\
INSTALLSHAREDWOWDIR: C:\Program Files\Microsoft SQL Server\
INSTALLSQLDATADIR: <empty>
INSTANCEDIR: C:\Program Files\Microsoft SQL Server\
INSTANCEID: SQLExpress
INSTANCENAME: SQLEXPRESS
ISSVCACCOUNT: NT AUTHORITY\NetworkService
ISSVCPASSWORD: *****
ISSVCSTARTUPTYPE: Automatic
MEDIASOURCE: d:\8268cd7b247d294de359c9\
NPENABLED: 0
PID: *****
QUIET: False
QUIETSIMPLE: False
RSINSTALLMODE: FilesOnlyMode
RSSVCACCOUNT: <empty>
RSSVCPASSWORD: *****
RSSVCSTARTUPTYPE: Automatic
SAPWD: *****
SECURITYMODE: <empty>
SQLBACKUPDIR: <empty>
SQLCOLLATION: SQL_Latin1_General_CP1_CI_AS
SQLSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE
SQLSVCPASSWORD: *****
SQLSVCSTARTUPTYPE: Automatic
SQLSYSADMINACCOUNTS: VISTA-PC\VISTA
SQLTEMPDBDIR: <empty>
SQLTEMPDBLOGDIR: <empty>
SQLUSERDBDIR: <empty>
SQLUSERDBLOGDIR: <empty>
SQMREPORTING: False
TCPENABLED: 0
X86: False
Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20141209_232121\ConfigurationFile.ini
Detailed results:
Feature: Database Engine Services
Status: Failed: see logs for details
MSI status: Passed
Configuration status: Passed
Feature: SQL Server Replication
Status: Failed: see logs for details
MSI status: Passed
Configuration status: Passed
Rules with failures:
Global rules:
Scenario specific rules:
Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20141209_232121\SystemConfigurationCheck_Report.htm
I will very appriciate if someone can help me solve it. I was trying to set Full control for my account in Properties/Security of root folder and try again but error is still.
Many thanks

Hi Foreverduy,
Before you run SQL Server 2008 express setup, make sure that you have installed Windows installer 4.5 and.NET Framework 3.5 SP1 manually. For more information about the process, please refer to the article:
http://msdn.microsoft.com/en-us/library/ms143506(v=sql.100).aspx. Moreover, please turn off all the third-party softwares which could prohibit the installation process.
According to your error message, the issue could be due to that your account has no rights to install SQL Server, or the corruption on the media.
Firstly, please ensure that your account has admin rights. Also make sure that you right-click the setup.exe and choose “Run as administrator” to complete the installation.
Secondly, please check if "msdbdata.mdf" file exists at d:\8268cd7b247d294de359c9\x86\setup\sql_engine_core_inst_msi\PFiles\SqlServr\MSSQL.X\MSSQL\Binn\Template. If it exists, please make sure that your account has read permission to the extracted
folder.
However, if the file doesn't exist in the extraction, the media could be corrupt. Please download the
media
again and check if the issue still occurs.
Regards,
Michelle Li

11gr2 installation setup shows error on a Virtual Machine !

Hi all,
I have a virtual machine which have Windows Server 2008 R2 Datacentre 64-bit.
When I install Oracle Database 11gR2 and click on "SETUP" file, a message box namely JAVA VIRTUAL MACHINE LAUNCHER and display below error;
_"Could not find the main class. Program will exit."_
Same setup runs successfully on my server with Windows Server 2008 Enterprise.
Is it 11gr2 supports a virtual machine which have Windows Server 2008 R2 Datacentre 64-bit ? or some other ?
Please guide me.
Thanks & Regards.
Dass,
Edited by: dassdhan on Jun 4, 2013 1:56 AM

dassdhan wrote:
Hi all,
I have a virtual machine which have Windows Server 2008 R2 Datacentre 64-bit.
When I install Oracle Database 11gR2 and click on "SETUP" file, a message box namely JAVA VIRTUAL MACHINE LAUNCHER and display below error;
_"Could not find the main class. Program will exit."_
Same setup runs successfully on my server with Windows Server 2008 Enterprise.
Is it 11gr2 supports a virtual machine which have Windows Server 2008 R2 Datacentre 64-bit ? or some other ?
Please guide me.
Thanks & Regards.
Dass,
Edited by: dassdhan on Jun 4, 2013 1:56 AMOracle doesn't know it's running on a virtual machine. That's the whole idea of virtualization.

2 AEBSn WDS setup woes/errors

Similar Messages

Maybe you are looking for