2 different lease time on same scope

Hi, is it possible to add 2 different lease time on same scope.
I have server and workstation on the same scope and I want to give the servers longer lease time, than the workstation.

Hi
It is possible to achieve this in the Windows 2012 and higher versions of DHCP Servers using the feature of DHCP policies. You can create a policy within a scope. In that policy you can specify the type of clients you want this policy enabled for. The type
of clients can be differentiated based on
MAC Address
Vendor Class
User Class
Client Identifier
Relay Agent Information (and its sub options – remote id, circuit id and subscriber id)
in DHCP Server 2012
and based on FQDN along with above in DHCP Server 2012 R2.
Once the policy has been created you can set the lease time for the policy as per your needs. For more details you can look at the blog post entry below.
http://blogs.technet.com/b/teamdhcp/archive/2012/08/22/granular-dhcp-server-administration-using-dhcp-policies-in-windows-server-2012.aspx
Thanks

Similar Messages

In iTunes: why different run times for same track?

I have occasional repeats of the same given track stored in iTunes. Sometimes, the 2 identical tracks show different running times. This happens when one track came from the Net (downloaded before I started using iTunes, then imported into iTunes) and the other comes from a commercial CD. Do you know why the differing times? FYI: In each case, I have checked the endings of both tracks; they are identical, so the music is the same even though one track is rated to run [much] longer than the other. Also, in "Get Info" there's a way to change the running time of a track, but this is no solution: if I enter a shorter run time, the track will truncate itself, and finish playing before the proper end of the song -- if I enter a longer time, I get dead air after the end of the recording. Any ideas?
Windows XP
Windows XP Pro
Windows XP Pro

"will iphone users in Singapore have access to application from other countries? "
No. You can buy from the itunes store in the country in which you reside.
Each country has the same rules:
"SINGAPORE ONLY. The Service is available to you only in Singapore and is not available in any other location. You agree not to use or attempt to use the Service from outside of the available territory. iTunes may use technologies to verify such compliance."
http://www.apple.com/legal/itunes/appstore/sg/terms.html#APPS

Execution of TestStand-Sequence in LabVIEW via TS-API: Different Execution times for same sequence

Hello Forum-Members,
I have a problem concerning the execution of an TestStand-Sequence in LabVIEW. I have created a VI that offers the ability to choose a TestStand-Sequence-File and then executes the sequence using the TestStand-API. The implementation is based on an example in C++-Application found following this link:
http://forums.ni.com/t5/NI-TestStand/Unreleased-references-using-engine-API-in-C/m-p/2927314#M46034
The implementation works quite solid in case the VI is executed the first time. The VI processes the chosen sequence in a acceptable duration.
But in case the execution is started a second time, the execution of the sequence takes ca. 30sec more than in the first case.
Until now I have not found a solution and hope someones got a hint concerning this problem...
I am using LabVIEW 2013 and TestStand 2013.
I have attached my own VI, a sample sequence with a small sample VI, so you can reproduce the problem.
Kind regards,
TobiKi
Solved!
Go to Solution.
Attachments:
Exe-TestStand-Sequence.vi ‏25 KB
Sequenz.vi ‏8 KB
Test-Sequenz.seq ‏5 KB

Hi Norbert,
first thanks for your answer.
What would be a reasonable way to replace the "Execution.WaitForEndEx"? My first idea is to get the respective thread of the execution and use the "Thread.WaitForEnd".
To clarify my problem:
The execution of the sequence itself takes longer time and so the execution of the calling VI. I have attached pictures of the log file of the first and second execution.
Further I don't get any dialog popups during the shutdown of TestStand. (I have activated the "ReportObjectLeaks" using the "DebugOptions") While developing the attached VI I've gotten several popups. But these popups disappeared after closing all references.
Maybe you have another hint how to locate the problem.
TobiKi
Attachments:
FirstExecution_20-08-2014.png ‏16 KB
SecondExecution_20-08-2014.png ‏16 KB

Two different Resultsets for the same query (running at the same time)

I am using the Thin Driver for Oracle 8.1.6. I am invoking queries in multithreading mode (each thread has his own connection to the oracle DB). If i am invoking the same SQL-Statement in two different threads nearly at the same time, only the ResultSet of the first query is complete. The ResultSet of the second query is not complete (the number of tuples differs each time I run the program). Principally the two ResultSets should be the same (no changes are done at the same time in the DB), but they are not.
Anybody knows this problem and knows how to solve it? Principally read accesses on DBs should not make such trouble ...
I hope anybody can help me.

Pranav,
As this BADI is having option checked 'Multiple use'. You can implement multiple implementations.
You need not to deactivate the existing implementation.
Reddy

Controller different Input in the same time in a real Scenario...(SIMULATION IN 2 TANKS CONTROLLER BY PCB BOARD)

Hi! I really need help....
I´m doing a simulation where I can controller the input and output with one external PCB, all is working properly (the communication) but my problem is, I can´t open where ever I want the different valves...I mean, I must wait until the process is finish...
The program is working with diferents process like this:
§Process 0:
Programinitialization. Tanks and pipes in zero state. Control for this state with “pump on” button.
§Process 1:
§State:
“ Pump on ” button istrue: Pump 1 isrunning, andTank 1 starts to be filled with water.
“ Pump on ” button is false: nothing happen, go to the next process
§Process 2:
This process is controlled from the “Control 1”button with is who control “Valve 1” for the discharge of water from tank 1 to tank 2.
§Process 3:
This processiscontrolledfromthe “Control 2 ”button with is who control “Valve 2” for the discharge of water from tank 1 to tank 2 if “Control 3 ” button is close or if “Control 3 ”button is open the water go out from the loop.
§Process 4:
This processgiveyoutheoptiontocome back totheprocess 1 ortotheprocess 2 dependingofthestate in process 3.
So my problem is I want run different processes in the same time, without having to wait out the current process is running....
this look like this:
and with the differents states...so I was trying to use a Statechart for try to improve the simulation....
like this:
But when I was tried to implement in labview with the statechart module i can't find the way to interconexión with this new module...
Because i need two differents regions...but i can't use the connexion between them....
Some new idea, help....all is welcome!!!
Thanks in advance.
Elena

Buenos días Alvaro,
Si, mejor en español
Si, me has entendido bien, exactamente es lo que me gustaria.
Empece por mi cuenta con labview y hay muchas cosas que se me escapan... Voy a implementar la máquina de estados a ver si asi soluciono el problema.
Muchas gracias!
Un saludo!

How Can I generate 2 different WaveForm in the same time

Hello,
I use a NI 6733 card and measurement studio 8 with MFC class.
I would like to generate 2 different waveform in the same time on 2 diffrent analog output channel.
I would like to know how can i do that bescause I succeed to generate one wafeform on one channel but not the second.
I would like to create 2 task one per analog output channel and waveform and launch the task in the same time.
I use the buffer FIFO and I think I have a probleme to share the buffer between the to different channel.
thank you for your attention.

Hello,
This corresponds of the third case detailed in this KnowledgeBase. You have to use one task with two channel, and feed it with your two independant waveforms (at the same sampling rate).
Cordially,
.mrLeft{float:left} .mrInfo{border-left:solid 1px #989898;font-size:x-small;color:#989898}
Mathieu R.
  CTD - Certified TestStand Developer / Développeur TestStand Certifié
  CLAD - Certified LabVIEW Associate Developer

Is it possible to realize two different processes in the same time with TDMS?

Hello all,
we have one TDMS but a lot of workstreams. Is it possible that 2 different workstreams in the same time realize anonymization in TDMS?
Thanks in advance!!!
Ilkin Mammadov

Hello Anita,
I am sorry.I mean we have a lot of projects (for example Procurement, Finance, Logistics, etc) and each of them wants to anonymize. But it is existing just one TDMS. Can these projects start with anonymization in the same time or they have to wait till one of projects finished anonymization?
Thanks in advance!
Best regards,
Ilkin

I would like to import two different cf cards from two different cameras into the same project/folder and have them be in order of the times they were taken, is there a trick?

I would like to import two different cf cards from two different cameras into the same project/folder and have them be in the order of the times they were taken, any ideas on how to do this?

Just import them normally and sort the project by date. They will fall into place. If you tried this and it isn;t happening then make sure the data and times on the two cameras are identical and make sure you are sorting by date and time and nothing else.

Time Division Multiplexing and Processing Different Loops at the same time

Hi, I am new in Labview so you may find my questions too silly, sorry about that
I want to design an interface to control the test&measurement devices remotely. I have two desks and there are several devices on these desks. The real problem is to use two different devices at the same time. To do this I heard that I can use time division multiplexing. But I couldn't find enough information about it in Labview. Another advice I heard was to use a matrice and hold the on/off state of the devices in this matrice.
Where should I start the design to create such a system? Do you have any advices? Thank you in advance.
My basic GUI is attached.
Attachments:
InterfaceAli.zip ‏42 KB

As Mike pointed out you cannot communicate in parallel on the GPIB bus - unless you have separate buses for each instrument - and that defeats the purpose of a bus. I am not sure about LXI.
With regard to your VI:
1. Do not use global variables to pass your data around.
2. You should use the Array data type, not the Matrix data type. The Matrix data type in LabVIEW should only be used for matrix mathematical operations (linear algebra) which cannot be easily performed on the array data type. You have many more tools in LV to work with arrays.
3. The Event structure needs to be in a parallel loop. This is basic data flow. If you do not understand this concept, get some training, either though the online tutorials or through a class.
4. Use Value Changed events and place the button terminals inside the event case for that control.
5. The parallel loops need to have a Wait or some other function which causes a delay. Otherwise, the first one to start executing could consume all available processor resources. These are called "greedy loops."
6. Use integer data types for case structure selector inputs. Floating point values are coerced to integers at the inputs. If the values resulted from calculations, unexpected rounding effects may occur, resulting in the wrong case being selected. In some cases using type defed enums may be even better. The underlying data is integer and the enum item names show up in the case selector labels, helping to document what the case does or why it was selected.
7. Remove the timeout case from the event structure since it never executes. Also avoid Use Default if Unwired on the terminal with your matrix (array) data. You never have a situation where an empty array is appropriate.
Before going any further with the program questions, you need to carefully define your requirements. How many instruments will you have? How many can be active at one time? What kinds of communication between the program and the instruments is required? This includes commands to the instrument, data returned from the instrument, error handling, and timing requirements. What will be done with the data? Display, save to file, use to automatically control another device? What safety requirements or constraints need to be met? Once you have a good requirements document, then you can begin to determine what kind of program architecture is best suited to meet the needs.
I suspect that you may be making some things much more complicated than they need to be while ignoring other important issues.
Lynn

Nas on airport extreme not recognized by time machine. same nas was previously used as time machine backup on different airport extreme. are there any configuration files that i can delete to fix this problem ?

nas on airport extreme not recognized by time machine. same nas was previously used as time machine backup on different airport extreme. are there any configuration files that i can delete to fix this problem ?

Time Machine has been working just fine, but in the last week or two it has given up the ghost. I reset the connections to the drive, and it will basically save a few bytes of data and then hang.
Although Apple originally announced, prior to the release of the first 802.11n AirPort Extreme Base Stations (AEBSn), that it would support Time Machine backups to AirPort Disks, they removed that option before they did finally release the base station for sale.
Since then, Apple has posted (as you have noted) that they DO NOT support Time Machine backups to AirPort Disks. As far as I know, they have not changed from that position and those who do these backups find that they become corrupted over time. Sorry, but it sounds like you just confirmed that for yourself.
1) Has one of the recent updates either on the AE (firmware) or OSX disabled this function?
No. Again, this feature has never been supported by Apple for every generation of AEBSn released.
2) Are there any changes I can make to get this working again?
If your data backups are critical to you, then you will want to use a different solution for your Time Machine backup destination drive strategy. I would suggest that you connect your WD My Book directly to your Mac in the mean time.
Your other options would be to either use a Time Capsule (which interestingly does support TM backups to AirPort Disks) or a non-Apple solution like the Drobo FS or HP MediaSmart server.

Can i open 2 windows under 2 different profiles at the same time?

Both me and my sister use facebook at the same time but we keep having to log out, i was wondering if i could open 2 windows (i have 2 profiles) under different profiles at the same time?

1) Check the firmware on router under status tab.....
2) Uncheck "Block WAN request" under security tab .... click save settings
3) If required forward ports under "Applications & gaming" tab .....
See if above settings work ....

Control two different parameters at the same time

Two motors were connected each other rigidly. One motor controlled torque and the other motor controlled speed. I generated some torque and speed data which represented one cycle of motion from a motor simulation. I like to send these two different data sets (torque and speed) to two different motors at the same time. Torque data sends to one motor and speed data sends to the other motor to see the response of the load profile. In order to do this, I thought about using multithread, but I am not sure it will work for this application. Usually multithreading delay the CPU time so the overall control process might be delayed, right? If you have better idea, please let me know.

If you are using one motion controller to control both motors, you will probably run into problems if you try to use multithreading on the PC. However, you can execute up to 10 programs (threads) at a time, in addition to host communication, using on-board programming. For more information on on-board programming please refer to the following tutorial: Developer Zone Tutorial: On-board Programming in FlexMotion
Best wishes!
Dawna P.
Applications Engineer
National Instruments

Why does the same clip play differently each time I play it?

Playing a flash animation clip in Adobe Media Player plays differently each time I play it. I'm looking at animation we made that has a left to right move. Sometimes it plays smoothly, other times it stutters, but the stutters happen at different points each time I play it, and the amount of stuttering changes each time I play it. I'm trying to decide if the file is acceptable to post on the web, so I'm playing the same 34 second file from my hard drive, each time in succession, yet each play is different. Boy, if you can help me with this I would sure appreciate it, as it is driving me crazy. (The same thing happens on other flash players). And no, the file isn't haunted...

Hello and thank you for trying to help me out. When I click on the itunes icon on my desktop, it does the preparing to install.... on my laptop, when I click on the icon, itunes opens automatically. I really can't figure out why one does this and the other does not.
Apparently, I was not having trouble connecting to the itunes store like I thought. Many other people complain of the same problem I had---the connecting to the itunes store progress bar goes halfway, stops, and then all I see is a blank white page that says itunes store. Well, after playing around, and clicking on VIEW and SHOW sidebar browser, I was able to see the itunes store! Yay!! It was so simple, it was unreal that so many people are having the same problem I thought I was having, connecting, when all that was was a VIEW issue.
As far as my desktop doing the preparing to install, I don't get it. I have uninstalled itunes9 and redownloaded it, reinstalled it. Same problem. Preparing to install. No matter what itunes icon I click on, or even if I click ont he application itself from it's folder. Any ideas?
So just forget about my connection problem---it was not a problem after all. Yet one pc does preparing to install when the itunes icon is clicked on, and the other pc does not. Both are running windows vista home premium. One is a desktop, one a laptop. I can't figure it out.

Can anybody explain how to print multiple copies of different documents at the same time as at the moment I have to open each individually and press print

Can anybody explain how to print multiple copies of different documents at the same time as at the moment I have to open each individually and press print

is this a windows in bootcamp question ?

Same query different timings , different sessions at the same time

I am running exactly the same query from 2 different sessions almost simultaneously and in one session it is taking 2 seconds and in the other it is taking 20 seconds. The explain plans in both the sessions (by set autotrace on) are exactly the same. The timing is almost same for succesive runs of the query in the same sessions. That is when I run the query again in the "slow session" it is always around 20 seconds and when I run the query again in the "fast session" it is always fast. The queries are being run within a few seconds of each other so the load on the database is almost same.
My hunch is that it is a database parameter that needs to be changed to solve this problem, can someone guide me with this ....which parameters I should ask our DBAs to adjust ? Our database is Oracle 10G.
Regards
Amitabha

Duplicate thread
Same query different timings , different sessions at the same time
Gints Plivna
http://www.gplivna.eu

2 different lease time on same scope

Similar Messages

Maybe you are looking for