2 e4200s on the same network?

I used to have this exact setup with 2 wrt610ns i believe was the model number, i have one at my house, connected to my dsl, and then another in my "man cave" connected by a approximately 250 foot buried outdoor cat6 cable, inside of conduit of course. Last week both routers along with my modem were fried during a storm, so now i rebuilt the network with 2 e4200s, i hooked everything up and b4 i even had a chance to set my network up like i had to do b4 (a 192.168.10.1 subnet in the mancave) everything was already getting internet, however i cannot access the web based setup for the 2nd router (mancave) the dhcp client table shows it with an address of 192.168.1.139. even if i disconnect, reset the 2nd router and set it up on a 192.168.10.1 address as soon as i connect it to the main router, it goes right back to the .1.139 ip address. the only problem i have with this is that i would like to have the freedom to change my wifi passwords or edit other settings on my network without having to disconnect from the main router everytime, assuming that will work and i wont have to do a hard reset in order to get the router back to a default ip. the cable connecting the 2 routers goes from a lan port on the 1st router to the internet port on the 2nd. any suggestions or information is appreciated

i suggest that you setup your two routers with 192.168.10.1 and 192.168.10.2 respectively. with 10.1 being your main router (connected to the modem), you may just run a wire from a regular port on the main router to another regular port on the 2nd router, then disable DHCP on the 2nd router. this way youd be able to access any of these two routers conveniently.

Similar Messages

Have Cisco E4200 and E2000 - want them both working on the same network...

I have a cable modem. My Cisco E4200 is connected to the cable modem and is my DHCP server for the house. But, the E4200 wireless does not reach to another part of my house. So, I bought an E2000 to connect on the network. The E4200 and E2000 are both routers and have the same default 192.168.1.1 address. I've tried to turn off DHCP server on the E2000 but I then I can't connect to it.
What are the steps to set up the E2000 so that is does not conflict with the E4200, is not a DHCP server, and will work with the E4200 on the same network. I've tried the Setup, Connect and also advanced settings via a browser - but I must be missing a step somewhere.
Is there a document that shows how to set these two up so that one is a DHCP server and the other is an "access point"?

follow the instructions in this link.
they must be wired to each other though. they cannot connect to each other via a wireless connection.

Multiple Users Mounting the Same Network Share?

Hello, first time posting...
I'll cut right to my main question: Is it possible, on OS X v10.3.9, for multiple users to simultaneously connect to the same network share?
Here in my office, we have a single Mac that is used by multiple people throughout the day. It has two accounts on it, 'Communications' and 'Studio'. 'Communications' is an Admin account that is used by a co-worker who spends the most time on the Mac. He created the no-limitation 'Studio' account for the rest of us to use.
There is a certain Windows network share that we both frequently use. We've found that if one user connects to the share first, the other user will not have access to it; using 'Go -> Connect to Server' will result in the share being greyed out in the list, and the share will not show up in the Finder.
However, there is one way around it. If Studio connects to the share first and then Communications (the admin account) attempts to make a connection of it's own *through a shortcut on the dock*, then a 'clone' of the share will be created on Comm's desktop, with a "-1" after the name (though it might be some other number).
This may sound like I've answered my own question, but what I'm looking for is a way for the non-Admin account to access the share after the Admin account already has (so that we don't have to log-in and disconnect Communications everytime Studio needs to manage files on the share).
We have Thursby Software's DAVE installed on the Mac, but I'm not sure how it fits into all this.
Any thoughts, suggestions or advice?
Thanks.

Bizarre. It turned out I could merge them, but only in to the mapped drive - L: - and only by explicitly clicking on the drive icon - if I typed L:\series in to dialog box it converted it back to \\nas\share\series... Not helpful.

HT4796 Migration assistant is telling me that it has lost connection with my Mac and to ensure they are on the same network. They are, and an ethernet cable is plugged into them. What do i do?

Migration Assistant has been running since yesterday evening. My Dell is now telling me that its trying to reconnect to my Mac and to ensure they are both using the same network. I have an Ethernet cable plugged in them and they are both on the same WiFi. What can I do?

Hello Wyodor,
thanks for your reply on my question.
You are wright the index file is 308 KB.
And offcourse that I delete my files and documents is not an Iweb problem, but because my English is not that good, that I thougt I try to tell the whole story, and hope people can read trough the lines.
Why I didn't use Iweb to upload to the server is because the server company recommanded to use file zilla. And I am a nobody with this kind of things, so I did exactly what they tell me to do.
No, i did not make a backup of Iweb and the domain file, but reading other messages on this forum showed me that I can maybe try to make empty the cashfile (?)
and otherwise I have bad luck and have to make my website again. Offcourse I have a lot of examples from all the pages (copied from the local map to my USB stick) and my website is aprox. 15 Mb, (not so big) so it will cost me a few nigths.
But I'm still hoping on a miracle :-)
greetings Lasource

HP Envy 5530 - computer won't recognize that the printer is on the same network

Product Name: HP ENVY 5530
OS: Windows 8.1
No changes made to system before issue occured
I bought this wireless printer last week (5-13-14). I have a working printer that was connected to my husband's work laptop via USB cable, but needed one to connect to our family computer, which is in a different room with the modem/router. My husband travels for work, so I want to be able to print without disturbing him and while he is away on business. I turned the printer on and connected it to my network with the password and printed out the network settings and the wireless report. There are about 8 other wireless networks in range of my printer (we're in a residential neighborhood), but we aren't having a problem with it connecting to someone elses stuff. I went online to download the driver software and it downloaded fine. I clicked on the desktop icon to launch the control panel for the printer and it opened up for me to install the printer. I went through every step and it won't recognize the IP address or the name of the printer, and therefore won't open up for me to do any scanning. Both the printer and PC are connected to the same network, but they won't recognize each other when it comes to going through the HP software to scan or print. I can go into word or something to print and it will let me print wirelessly, but it won't do anything from the control panel of the print software because it thinks the printer hasn't been installed. I've had Windows 8 on this computer since I bought it in 2012, but I have the computer defaulted to go to my desktop instead of the start screen, so I don't know if that makes a difference. I am going to go ahead and remove the device and uninstall everything so I can try again later. If I had known this was going to be a problem, I would have not bought the printer and just kept on doing what we'd been doing.

Hello SarahD_07,
Welcome to the HP Support Forums!
I understand you are having some troubles getting the Envy 5530 printing wireless on Windows 8.1. Are you able to take the I.P address of the 5530, type it into the address bar of your web browser and hit enter. Does it load a page about the printer?
Run the Print and Scan Dr to see if it can clear up the scanning issues if you can view that above page.
I will look out for your reply,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

My ipad with retina display can't find my epson artisan 730 wireless printer. They are on the same network and printer's wireless connection is excellent. What are the steps to fix this?

My imac won't pick up the printer either. Even after I updated it's software. My ipad is new. Any help would be appreciated. Thanks!

No change. The printer still doesn't show up on my devices even though they are all on the same network. On the printer's connection print out the connection reads Pass and that the network is working correctly. However, then it states "*A router/access point channel conflict has been detected. If you have problems printing or scanning, Improve your wireless network environment." "*If the problems persist, see your documentation for help and networking tips."
I've gone through all the documentation and still can't figure out what the problem is. I've had the router checked out by my building and they claim everything is in order. I have a excellent signal.

Issue to send email (using sp_send_dbmail) with an attachement located in other server within the same network

I have two servers. One is for databases (DB) with the mail server configured and the other is for SSIS without mail server. Both servers are in the same network. On the SSIS server the SSIS package exports data from the DB server table
to xls file. The file is saved in SSIS server. When I created a task to send the email (using sp_send_dbmail) to attach that file, I got the error message:
Error: Executing the query "EXECUTE [msdb].[dbo].[sp_send_dbmail]
@profile_na..." failed with the following error: "Attachment file H:\test.xls is invalid.".
Any help will be appreciated. Thanks.
A Fan of SSIS, SSRS and SSAS

Where are you running this?
If its in the other server (DB) you need to use UNC path to the SSIS server folder where file resides
Also the executing account should have access to the folder as well as the file. So If you're running this from a job make sure you either provider folder and file access to sql agent job service account or create a separate proxy account with the required
permissions and configure the job to use the account
see
http://www.databasejournal.com/features/mssql/article.php/3789881/Proxy-Accounts-in-SQL-Server.htm
http://www.codeproject.com/Articles/28918/SQL-Server-Agent-Proxy
Please Mark This As Answer if it solved your issue
Please Vote This As Helpful if it helps to solve your issue
Visakh
My Wiki User Page
My MSDN Page
My Personal Blog
My Facebook Page

I loaded in Lion - but my time capsule will not back up. I get an message: couldn't complete backup due to a network prolem. Also it says "make sure your computer and back up disk are on the same network, and that the backup disk is turned on.

I installed Lion on my Mac Pro laptop. Regarding Time Capsul - I get a messaage as follows: couldn't complete backup due to a network problem. Make sure your computer and back up disk are on the same network and that the backup disk is turned on. Then try again to back up. I have time capsul turned on. bill

I have exactly same problem with my MBP and MBA, after upgrading to Lion. I've tried to fix this issue while cheking key chain issues and network setup, even formating hdd and time capsule firmware upgrade (ver. 7.6.1.). Nothing can help. It is very annoying.

Homeshare worked on my PC until recent iTunes update. Cannot get homeshare to work on PC as previous. When I use my MacBook Pro on the same network, iTunes/AppleTV works just fine, so it has to be iTunes?

An interesting observation...when I have a MacBook Pro connected and select Computers on my AppleTV2, the name of the MacBook computer comes up on the screen and allows me to select it and view photos from my iTunes library. Orks perfectly. When my Windows 8 PC is connected, and I select Computers on my AppleTV, the name of the PC does NOT come up on the computer list, but instead the AppleTV immediately tries to download pictures from the PC itunes library. It runs for ~2 minutes then generates an error message saying it could not connect to the iTunes library and to make sure it is tunrned on, connect to the same network, and use the same blah, blah, blah. I know all the settigns on the network are correct because my MacBook works perfecty. So frustrating that my PC worked previously before the recent iTunes software update. What to do to fix it?

Hi Rickgal,
Thanks for visiting Apple Support Communities.
Based on the information, it does sound like this behavior is isolated to your PC. I recommend trying the troubleshooting steps in this article on your PC:
Troubleshooting Home Sharing
http://support.apple.com/kb/TS2972
Start with turning Home Sharing off and on again, as explained in step 3:
Go to File > Home Sharing and choose Turn Off Home Sharing.
Choose File > Home Sharing > Turn On Home Sharing.
When prompted, enter the Apple ID you'd like to use.
Click Turn On Home Sharing, then Done.
Best Regards,
Jeremy

How can I share itunes content between 2 macs (both mine) in 2 different locations? Same Apple ID, same account, not the same network.

I haev a main mac at my main home which syncs itunes to my ipad and iphone with no problem. I want to access the same itunes content at my mac in my second home which is obviously on a different network. I have my ipad and iphone with me so they can be on the same network as the second mac. I can share the purchased itunes content but not the uploaded content. Any ideas?

Ok well that is not uploaded content. Maybe ripped content is a better term.
You can transfer purchased content from your iOS devices into the new Mac if you want.
iTunes Store: Transferring purchases from your iOS device or iPod to a computer
http://support.apple.com/kb/HT1848

I rented a movie from iTunes on my apple tv, can I watch this rental on another apple tv that's on the same network and under the same account?

I would like to rent a movie from iTunes on one of my apple tv's and would like to know if I can watch that movie rental on another apple tv on the same network. I used to rent movies on my Mac and was able to watch on different apple tv through home-sharing.

Hey hskcheng,
Movies rented on an Apple TV can not be transferred to a different device. See this article for reference -
iTunes 12 for Mac: Rent movies from the iTunes Store
Thanks for using Apple Support Communities.
Happy computing,
Brett L

How can I connect my mobile device on the same network with my printer

I have pictures on my mobile device but I am unable to print them on my HP Photosmart plus printer. I was wondering how am I able to make sure that my printer and my mobile device is on the same network so I can print my pictures or either be able to save them to my memory card?

Hi,
Are you talking about iPad, iPhone ?? If YES then please check your printer on this list,(updated on 15Dec2011) it must be an AirPrint enabled printer to be able to print from iPad, iPhone. If YES (again), you can use AirPrint on your iPad to print.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

HT4356 I have an air-print enabled printer: HP Premium e-all-in-one C310. Can't print from iPad iOS6. They're on the same network, but have different IP addresses. On the iPad it's 192.16.1.126 and on my printer it's 192.168.1.133. Can I match them? H

I can't print from my iPad2 to my air-print enabled printer (HP Premium e-all-in-one C310). They're on the same network, but have differed IP addresses! The iPad IP is 192-168-1.126 and the printer is 192-168.1.133. That's the only difference I can see. Is there a way to fix this?

fyi:
you put periods between the numbers.
Each device needs a unique number.
for the 192.168.1 the right must number should vary. 192.168.1.x
the numbers you have look ok.
Power off all devices: wifi router, printer, ipad.. wait 10 minutes. poweron router ... wait power on printer wait then power on ipad.
cross fingers.
Robert

How do I set access to the same network share on a Windows server for multiple users on an iMac (school set-up) in Lion 10.7.3?

We've got them authenticating/binding with AD (after hours of troubleshooting to get working), and their Home drive on the Windows 2003 server loads in the dock, but they also want to be able to load the same network shares on the server e.g. "Students$" for every student that logs onto the iMac. I realise without Lion server we can't control it by group, but if we could at least set it up consistently for the students that would be a great start.
Thanks.

When you install you get the opportunity to install it for "All Users".
It sounds like you have a demo version on your Mac however, you need to delete it:
http://www.freeforum101.com/iworktipsntrick/viewtopic.php?t=105&mforum=iworktips ntrick
Peter

Multiple printers on the same network problem

I have 2 HP OJ Pro 8600 printers and one HP OJ Pro 8500 Plus printer on the same network. My question is whether it is possible to change the network name of these printers so that it is easier to identify them.
The printers are in three different buildings so there is little stress to run around to find out where the print comes.

Hi JObbern
If all the printers are on the same network you won't be able to change the network name on the printer.
You can change the name of the printer though on each computer. Depending on the operating system you are using, go to the printers window, right click and rename. Example Office1, Office 2.
If the option isn't available you can go to the printer window and add a printer and change the printer name through the wizard.
Hope that helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

2 e4200s on the same network?

Similar Messages

Maybe you are looking for