2 hard drives, 2 OS (Tiger/Leopard) same Mac...any suggestions?
2 hard drives, 2 OS (Tiger/Leopard) same Mac...any suggestions?
I'm thinking of adding a 200gb hd to a g4 mac that has a 80gb hd installed. Would like to run 10.5 Leopard on the 200 and 10.4 Tiger on the 80 to accomodate software that won't run on 10.5. Will that work? That is the question. Any suggestions?
Similar Messages
-
I have followed th steps to back up my itunes library to an external hard drive but when I try to drag the itunes folder to the hard drive it does not let me. Any suggestions?
Go through the below forum with similar issue and follow the process mentioned by "Macjack" in the beginning.
https://discussions.apple.com/thread/4499820 -
Using snow leopard on external hard drive w/Mountain Lion OS Mac
I need to use Snow Leopard in order to use some expensive software that will not work in Lion or Mountain Lion. All of our computers have been upgraded to Mountain Lion, whcih doesn't support Rosetta. I was able to install Snow Leopard on an external hard drive and it boots up fine from another computer (that is not mine) that has Snow Leopard as its OS.
But when I boot up from my MacBook Pro (running Mountain Lion) and from my Macbook Air (also running Mountain Lion), I can't seem to do it. I hold the "option" key when starting and I get the option to start from the computer's HD or from the external firewire Snow Leopard drive. When I choose the Snow Leopard drive, it crashes and gives me that black screen with the kernel (?) message in several languages that I need to hold down the Power key to turn off the computer and reboot.
How can I get my MacBook Pro or my MacBook Air to boot up from the Snow Leopard external hard drive? (Once again, it DOES work with a Mac that has Snow Leopard as its OS).Richard Signes2 wrote:
The question is: How do I start up my MacBook Air (or MacBook Pro) from an external FireWire Bootable hard drive with Snow Leopard on it? When I start up either one with the "option" key pressed, I get the option to start up with the external Snow Leopard hard drive, but when I select it, it crashes, as described above.
You can't if the Mac is a Late 2011 and later, perhaps if it's a Early 2011 (as some came with 10.6 and some with 10.7) and it should be possible for all Intel Mac's earlier than Early 2011.
Also, like what has occurred in the past, Apple does eventually issues a firmware update in later OS X versions so that earlier OS X versions, despite the Mac previously being able to boot from them, won't any longer. However far as I know Apple hasn't done this quite yet, but will one day.
Baring those issues, if you installed 10.6 on a external drive using a machine specific black/gray disk from another Mac, it has hardware drivers for that model/year of Mac only.
If you used the 10.6 white retail disks from Apple, it only has hardware drivers for all previous Intel Mac's that came originally with 10.6.2 or earlier from the factory. Mac's with 10.6.3 or later on the drive from the factory have different hardware drivers, thus not on the 10.6.3 white retail disk.
To find out what OS X version came on your machines, use the free MacTracker and use your model indentifier in the Apple menu More > Info (aka System Profiler)
So for those Mac's that originally came with 10.6.3 or later, machine specific disks must be gotten from Apple, or if your really talented, it's possible to create a univeral 10.6-10.6.8 install disk by combing the 10.6.3 image with the 10.6.8 combo update which will boot on any Intel Mac if the firmware permits and the hardware drivers are compable.
There is a method to bypass the firmware and install on Mac's that are Early 2011/Late 2011 via Target Disk Mode, or via taking the drive out of the machine as some Late 2011's use the same hardware drivers as the Early 2011 machines (only a processor bump basically)
How to revert your Mac to Snow Leopard
For the MacAir, you can install 10.6 via a USB thumb drive, of course provided it has the hardware drivers.
http://www.maciverse.com/install-os-x-snow-leopard-from-usb-flash-drive.html
So in your case you likely should be rather looking at running Snow Leopard in a virtual machine program in Mountain Lion, which MichealLax over at MacRumors has perfected a technique.
Windows in BootCamp or Virtual Machine?
http://forums.macrumors.com/showthread.php?t=1365439 -
Any EASY, simple to use external hard drives that are PC and Mac interchangeable?
I have a new Mac Book Pro, running Mountain Lion. I am new to Mac; my old laptop is a Dell running Windows 7.
I would like to move over ALL my pictures and files from the Dell to an external hard drive (EHD) that is also Mac-compatible. I want all the pictures and documents SAVED and easily retrievable on the EHD, but probably don't really need *ALL* of them on the Mac.
Does anyone know of an EHD that will do this? One that is really super easy to use and won't need "reformatted". (I don't want to have to try to deal with that!)
I just want to put ALL my stuff from my Dell on an EHD, then move over SPECIFIC items from that EHD to my Mac.
Any advice? Recommendations? THANK YOU!Bob,
I'm sorry, my message was unclear! No, I'm not looking to hook up two computers at one time to one EHD.
I'm just looking to be able to use one EHD, and go back and forth between it and the Mac or Dell, getting stuff off one, and putting stuff onto the other.
I have all my old Dell files and photos already on the EHD. I was afraid that once I formatted the EHD that those files from my Dell that were already there would somehow no longer be accessible to transfer to the Mac? But it sounds like this isn't so?
So, to clarify: I would like to continue to have access to the files on the EHD (from the Dell). Once I format the EHD, will those files still be accessible to me, to either leave "as is", or transfer to the Mac, now or later?
THANK YOU! -
Have a MacBook Pro running Lion (10.7.9) and an IMac running Snow Leopard (10.6.8). Want to Back up both images and restore on opposite machines. Essentially swapping images between hard drives. Is this possible and any "gotcha's" to look for? Thanks
If the MBP came with Lion, it most likely won't boot with SL. Easiest thing to do is create a bootable backup/clone of each to an ext HD, partitioned to hold each on a separate volume, ensure that the original machines can boot with their respective clones, and finally, try booting the other machine with the other clone. Images are useless since you can't boot with them to test them out.
-
How do I properly zero out or erase the hard drives in my early 2009 Mac Pro 4,1 tower?
How do I properly zero out or erase the hard drives in my early 2009 Mac Pro 4,1 tower?
I assume there are already instructions on Apple.com someplace but haven't seen them yet… I have to one terabyte drives one the operating system the other is blank I want to start fresh I want to zero out both drives but I didn't want to make any mistakes
I know I can use disk utility to 0 Out Dr., #2 that means I will have to take out the operating system hard drive out of my 2008 Mac Pro and put it into my 2009 Mac Pro to use the disk utility to zero out drive one the OS drive in my 2009 Mac Pro am my correct
I just need a little bit a help I want to go slow so I don't make any mistakes with the sleds or with the erasing process which journaled to choose encrypted or not etc. etc.
Furthermore is there instructions on the site on how to change the hard drive into a different sled because the sleds and my 2009 are different than my 2008 any advice
Thank youI'm doing this because my friend told me that zeroing out the drive can nap bad sectors and also later for some kind of diagnostics usage of the drive or something like that he wasn't really clear
My friend was really specific he said choose the option that writes zero's once over the drive that is plenty good enough I was inclined to use the maximum seven write ...I just want to make sure the drive has no bad sectors and that's it's it's zeroed out for possible future diagnostics usage or something that he said was usable later
he also advised me to run a test on it but I don't have the software you mentioned or the software that he has… So I may have to take the drives over to his house unless you have some kind of free software that's easy to use that you could suggest that will not only zero out the drive but test the drive completely
I am completely new to Mac I'm no dummy but at the same time I'm not super technically capable I mean I can surprise myself I'm pretty good but I need a good teacher… How expensive is this lifeguard software?
Thank you -
Will Logic Pro 9 run on a 2007 4GB ram, 320GB hard drive, Intel 2 duo 2ghz mac mini?
"Will Logic Pro 9 run on a 2007 4GB ram, 320GB hard drive, Intel 2 duo 2ghz mac mini?"
I am looking for the cheapest way possible to run Logic Pro 9 and will purchase a second hand mac mini if it will run the software.
Thank you!Yes it will.. I would recommend you use the combination of Snow Leopard 10.6.8 and LPv9.1.5 (or 9.1.8 if you have to..) with that particular hardware to get the best performance out of it... I would not recommend running any OS X version higher than 10.6.8 as each new version of OS X from then onwards.. placed a bigger performance hit on the hardware... and frankly, less stability with LP9.
As to how well it will run on that hardware.. will more depend on the sort of loads you place on it.. depending on the type and content of the music you wish to compose... It will run and you should be able to create reasonable sized projects.. but again, it all depends on the plugins used.. the number of them... the number of tracks and so on... so to give a more precise answer is difficult. -
No Hard Drive after installing Leopard
Hi, i just installed leopard on my macbook and everything went very well until i turn it off and then turn it on again. It just popped a kernel panic screen, just after de main grey screen with the apple logo on it. So I try to reset the PRAM and doesn´t work, and I am stuck like in the middle of nowhere because apparently I have no hard drive to install leopard.
I try to verify the disk with disk utility but nothing happens, so I try to reinstall leopard and guess what, I have no hard drive to chose for installation.
What can I do? Thanks in advancehey, my hard drive died recently and i don't think it had anything to do with leopard either. you might want to check what kind of hard drive you have because a certain type of seagate hard drives that are installed in mac computers are defective and can crash at any time. i would check out this website and see if this might be your problem...
http://www.appleinsider.com/articles/07/11/27/appleaware_some_macbooks_contain_flawed_seagatedrives.html -
Need advice on hard drive set up for a Mac Pro
Just changed over to a Mac and would like some advice on hard drive setup. Have a Mac Pro 2.8 with the 320 gig hard drive.
I plan to run Windows with MS Flight Simulator and Office 2007 through VMware Fusion/Boot Camp.
Will be transferring camcorder video to edit and make DVDs. Lots of music, podcasts, photos, and short videos will be stored.
I'm planning to buy additional hard drives.
Any suggestions on how many/what size hard drives to get.
What should the stock 320 hard drive be used for?
Where would I put the Windows stuff? What format/partion size?
Where should the backup go?
I've seen many positive comments on Western Digital Caviar Black drives, would that be a good choice?Welcome to Discussions!
Here's my (current) setup.
4 x WD640AAKS. As Hatter says, brilliant drives. Whisper quiet and very fast. Plus extremesly good-priced.
Drives 1 and 2:
Raid0 boot volume. Also set as Photoshop scratch. I ran lots of tests on different setups and this is faster than having a separate scratch drive, almost the same as having a separate internal raid0 for scratch. But I felt I couldn't motivate that use of harddrive bays for the little extra it offered in speed.
Drive 3: User account on first partition and a second, 23GB partition for Windows XP.
Drive 4: Time Machine, which only backs up the User account partition.
I clone the startup drive to an external regularly. In fact I have three bootable clones, one OS X with latest updates, one with OS X with latest updates and my applications, and one of the boot volume before any major updates - overkill perhaps... I use the 320GB OEM drive in an FW800 enclosure for this.
/p -
New hard drive installed on my 2009 mac book. Can I reinstall pages, numbers, etc... from the App Store? I was running Lion.
HI Corey ...
Yes. Make sure you use the same Apple ID.
How to re download apps from the Mac App Store:
Open the App Store. From the menu bar click Store > Sign In
Click Purchases from the top of the App Store window.
Select which apps you want to re download. Then right or control click where you see Installed then click Install.
Make sure and use the same Apple ID used for the original purchase.
If you can't re dowload the apps, launch iTunes. From the iTunes menu bar top of your screen click Store > Authorize This Computer. Sign out of the iTunes store and try re downloading your apps from the App Store again. -
Hi guys
It's starting to irritate me that I still can't copy folders of more than 4GB to my external hard drives. I've checked some websites that told me that the external hard drive should be setup as "Mac OS Journaled", but when I check this via Disk Utility, I find out that they are. What is another solution for this problem, cause it takes a lot of time to select folders within folders within folders to copy to the external hard drive, instead of just copy and paste the main folder...
Thanks in advance!
BobOkay so today I've erased one of my external hard drives, and reformatted it as "Mac OS Journaled". If I copy a huge folder on it from my MacBook to the external HD, there's nothing wrong and it goes fine.
But then when I try to replace the folder with a more up-to-date version on my MacBook, the Error Code 0 shows up again.
So: reformatting didn't work out. Putting huge folders on it goes fine, but replace them with a newer version of the huge folder, doesn't work.
Any solutions? Please?
Thanks guys! -
How can i erase a hard drive on a water damaged mac?
Hey guys sorry if this is a simple question im not real computer savvy when it comes to hardware and that but anyways. MY macbook pro got water damaged recently and i got a new one and was wanting to sell my damaged one as any funds that can help to recover the cost of the purchase would be great.
So my question, is there a way it is possible to have the hard drive erased before i sell it as it has work documents, photos etc on it. It was only the logic board that was damaged with the water so it wont turn on and what not but the hard drive itself is intact...Any help would be great thanks!Often when a MBP has been baptized the HDD is still intact. If the damaged MBP can be turned on you might try target disk mode:
https://support.apple.com/kb/ht1661
If that will not work, then take out the HDD and place it in an enclosure. Connect it to your new Mac and then use Disk Utility>Erase.
Ciao. -
How can i format my external hard drive to write files from Mac without loosing the files that i alredy have on my external hard when i used it with windows?
I have been using Windows to write files to my 1TB WD external hard drive and I do not want to format to loose the files capacity of around 500GB
Someone, Please helpHi Allen,
Is there any way to store the back up to Mac and restore after formating? -
I have Lion as my current and main OS. Is it possible to partition part of my hard drive for Snow Leopard? I'm good on partitioning but when I insert the Snow Leopard install disk a message tells me I can't run the install program because I currently have Lion installed... obviously. Have I gone about this the wrong way? Do I need to boot the computer using the Snow Leopard install disk instead of my main HD?
Apple will never update that as for the most part it is true, and the fact that they really don't want you to run older OS X versions (for whatever reason).
Now this probably won't work with the next line of MBPs and MBAs that come out. But it is for the current builds.
But as I stated you need one of the lastest builds of SL for it to even boot the system.
It won't work with the retail 10.6.3 DVD disc. That version does not have the correct drivers for the newest Mac's. -
i formatted my ext hard drive and changed it to mac os x extended(journaled). then i put in all my data back. after a while, i insert the hard drive but my macbook cannot read it. plz help
SanandaDutta
tried on a different mac. The same problem exists.
If that is the case, its extremely unlikely you have a bad USB cable on the seagate, rather as I mentioned earlier a bad SATA bridge card.
If the Seagate 1TB USB external wont open on either Mac and youve verified same (try a diff. USB cable if you have one however this is nearly never the case),....then to get the data off that HD (unless it is dead which is also extremely unlikely),......then you would need to extract the HD from its case and insert same into either a HD dock or USB HD enclosure.
8 out of 10 seemingly dead inopperable 1-3+ year old external HD are perfectly fine, rather the cheap 50 cent SATA bridge card fries and dies (alas)
reply back if you need help in extracting same.
Maybe you are looking for
-
My computer keeps showing a blue screen everytime i get online and says memory dumping error
what should i do when my cpu keeps turning off everytime i turn it on and go online. plus their will be a bunch of pop ups that just open up without my permision
-
How to connect a second computer to an airport extreme network
how do I connect my macbook pro to an existing airport extreme network. The AE basestation is showing up on the macbook but when I click on it it tells me its not connected ??
-
Function Module to Simulate Goods Receipt With Landedcost.
Hai, I Used the Function Module "MB_SIMULATE_GOODS_MOVEMENT" From this i can get Landedcost for the material . But It is Requiring atleast One open quantity, Can I have anyother alternative FM for this Reply as early as possible
-
9i and 10g on same host + listeners
Dear All, I have 2 simple questions: 1- Is it possible to have 2 database servers on one machine given that one is 10g (10.1.0.3) and the other is 9i (9.2.0.x) ? 2- Second, which of course is valied if answer to question 1 is YES, What about lsnrclt
-
Problem syncing iPhoto albums through iTunes
While using iTunes 11.0.5 to sync iPhoto 11 albums to my iPad, iTunes seems not be awaree of any update in the contents of the albums. iTunes also recognizes new albums if I create them in iPhoto, but indicates they contain 0 photos. This way I am no