2 iPads, but can only connect one iPad at a time to my home network.  Is this a known issue with Mac/iPads in general?

At home I have a HP PC, netbook and Sony laptop with no connection issues.  Last year I bought an iPad 1 for my wife.  This year I bought an iPad 2 for myself.  However, only one iPad can connect to the wifi home network at a time. If I am using the iPad2 then the iPad1 fails to connect to the internet.  if the iPad1 is being used then the iPad2 cannot connect.   I tried resetting iPad network settings for both, reset router, and updated both iPads to latest software/firmware yesterday.  Right now the only iPad that shows any connection is the iPad1.  The iPad2 does not see the home network or any other outside network.  Any suggestions or ideas on how to resolve this?  It is odd the network issues only affect the iPad's.

@dananova,
It sounds like you need to either increase the number of dynamic IP addresses your router will hand out or change some of your devices to static IP addresses. 
Check the router manual on how to change the dynamic IP range of your router.  If you don't have a manual, you can go to Belkin's website and download it.
To change the IP address of your iPads to static addresses, go to Settings > Wi-Fi and tap the ">" next to the name of your wireless network.  DHCP should be highlighted.  Write down the all the settings on the screen. Next tap the Static button.  Enter the exact same information that you copied from the DHCP screen with the exception of the last 3 digits of the IP address.  Enter a new 3 digit number in this spot.  Generally the original IP address will end with a low number such as 009, so pick a number that is not that low but less than 255.  I would suggest a range of 240 to 250, unless the original IP range falls near this range.  Also make sure you use a different 3 digits for each device you set to use a static IP address.

Similar Messages

  • I am trying to print all the PDF pages in a range of 5 pages but can only print one page at a time . . . It will print the current page, but not all or pages 1-5.  Can this be overcome?

    I am trying to print all the PDF pages in a range of 5 pages but can only print one page at a time . . . It will print the current page only, but not all or pages 1-5.  I need to go to the next subsequent page and command to print current page; continuing with this procedure until all pages are printed one at a time. Can this be overcome?

    You can use printPages(1, 5), however I need to know how you print current page.

  • ITunes tells me "Could not be used because the original file could not be found. Would you like to locate it?"  I can locate it and all my other music, but can only open one song at a time.  How do I set it to open all my music whenever I want it?

    iTunes tells me my song selection: "Could not be used because the original file could not be found. Would you like to locate it?"  I can locate it and all my other music, but can only open one song at a time.  How do I set it to open all my music whenever I want?
    Message was edited by: Woildbill

    I just spent several hours dealing with this when switching to a new PC. It was extremely frustrating as I knew my files were on my external HD but no matter how many times I copied my old iTunes folder over the files were still missing...because dummy me had forgotten to "unhide folders" on my new PC and my old files were actually stored in a hidden folder created long long ago.
    This is how I did it on Windows 7 with iTunes 10
    1. Look in iTunes Advanced Preferences to see where iTunes is saving files. (Edit, Preferences, Advanced)
         Example: C:/Users/Woildbill/My Music/iTunes/Music
    2. Ensure you are able to see hidden files - Control Panel, Folder Option, View, Show Hidden Files
    3. Use Your Computer's Search Function to Locate the Missing File (Start, Search, type name of song - I started my search in "My Music" folder but be sure to expand to entire Computer if not found right away)
    4. In Search Results, right-click found folder and select properties. This will tell you where the file is actually stored.
    5. Use Windows Explorer (right-click start) to navigate to the location of the file. It is likley your other missing files are in the same location.
    6. In Windows Explorer, copy the newly located files to the iTumes location from Step 1 and everything should work again.
    Hope this helps!

  • WRT45G: can only connect one pc at the time to internet, cannot login to router setup

    Hello,
    I don't get this. The complete network worked fine for ... years? After a call with the ISP about a general/different issue, we can now only connect one pc at the time to internet. (We were asked to take out cables and we've put them back).
    I've been trying and searching for an answer for hours.
    problem:
    We can only connect through the router to internet with only one pc at the time (the first pc we connect after starting up the router).
    Also we cannot get into the setup menu of the router at 192.168.1.1
    We've been trying to reset the modem for 10, 30 seconds.
    Auto resolve IP/DNS. DHCP is enabled.
    I also remembered that I pushed the SES button, it turned from orange to flashing bluish. I never knew aboutthis function, nor it is mentioned in the manual I downloaded. Now this SES indicator is off.
    Also WLAN and DMZ led are off.
    I downloaded EasyLink_Connect.exe, went through the setup. It recognises there's internet connection, but stops and says: cisco does not support this modem.
    Temp. replacing this WRT45G modem with another one did not resolve the issue.
    I have no clue what went wrong, what we did wrong, and how we can resolve this issue? Please help! Thanks
    Message Edited by Brammm on 11-27-2008 03:13 PM

    Okay! 
    1.  (results when having assigned a static IP) :
     Windows IP-configuratie
             Primair DNS-achtervoegsel. . . . .:
            Knooppunttype: . . . . . . . . . .: onbekend     (unknown)
            IP-routering ingeschakeld. . . . .: nee      (no)
            WINS-proxy ingeschakeld . . . . . : nee    (no)
     Ethernet-adapter LAN-verbinding:
             Verbindingsspec. DNS-achtervoegsel:
            Beschrijving . . . . . . . . . . .:
              VIA Compatable Fast Ethernet Adapter
            Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
            DHCP ingeschakeld:. . . . . . . . : nee    (no)
            IP-adres. . . . . . . . . . . . . : 192.168.1.20
            Subnetmasker. . . . . . . . . . . : 255.255.255.0
            Standaardgateway. . . . . . . . . : 192.168.1.1
            DNS-servers . . . . . . . . . . . : 192.168.1.1
     (results without having assigned a static IP: automatic config.) :  
     Ethernet-adapter LAN-verbinding: 
            Verbindingsspec. DNS-achtervoegsel:
            Beschrijving . . . . . . . . . . .:
              VIA Compatable Fast Ethernet Adapter
            Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
            DHCP ingeshakeld. . . . . . . . . : ja     (yes)
            Autom. configuratie ingeschakeld. : ja       (yes)
            IP-adres. . . . . . . . . . . . . : 84.30.99.32       
    Subnetmasker. . . . . . . . . . . : 255.255.254.0       
    Standaardgateway. . . . . . . . . : 84.30.98.1       
    DHCP-server . . . . . . . . . . . : 213.51.144.90
            DNS-servers . . . . . . . . . . . : 212.54.40.25
                                                212.54.35.25
    2.  I do have another router, when I try that one, the problem we have remains. So that's a bit strange to me. That one is supposed to be working.
    Does this SES function configure anything other than the modem? So, does it alter PC configurations? I have no clue.   We even start to wonder whether the ISP is able to set up their internet in a way that unables us to make use of a router? That would be ridiculous
    Message Edited by Brammm on 11-30-2008 04:03 AM

  • Can only connect one user at a time via VPN?

    Hi, long-term Mac user but new to OS X Server. Dug thru the forums quite a bit but couldn't find an answer to this one - hopefully I wasn't searching with the wrong keywords.
    Installed OS X Server 10.6 on a MacBook (white, 1 generation back) at the office. Sits behind an Airport Extreme, which is connected to Comcast. Other machines at the office are NOT routed through the Server, but rather connect directly to the Airport Extreme for internet access. I've set up server.mydomainname.com to point to our Comcast address, and I am able to connect via VPN to the server without any problems, and access the server using the server.mydomainname.com address which I pointed to my Comcast IP address, as long as I check "Send all traffic over VPN connection" on my client.
    However, when I'm logged in via VPN on one computer, and then log in via VPN on another computer (with the same UID or a different one), the first one loses all connectivity through the VPN - it's as if it had been logged off.
    In Server Admin, under the Settings|Network tabs, I have Computer Name set up as "theserver", and Local Hostname as "theserver" (so I can access via theserver.private). VPN is set up to enable L2TP over IPsec, sharing ranges 10.0.1.200 thru 10.0.1.220; no load balancing, no PPTP. Client DNS servers is set to 10.0.1.29.
    Any ideas as to why I can only connect with one client at a time?

    Thanks. I didn't see anything interesting, but then again I'm not up on VPN details. Here's the scenario:
    First, I logged in as "user1", and I can use the VPN.
    Then, I logged in as "user2", and I can use the VPN with user2, but user1 is no longer able to do anything over the VPN.
    Then I hung up with user2, but user1 still can't see anything over the VPN.
    Then I hung up and reconnected with user1, and user1 can use the VPN again.
    Here's part of the log for this activity. I've replaced potentially identifying info with "XYZ" for safety. Appreciate any thoughts on this!
    Tue Oct 19 07:33:08 2010 : L2TP received ICCN
    Tue Oct 19 07:33:08 2010 : L2TP connection established.
    Tue Oct 19 07:33:08 2010 : using link 1
    Tue Oct 19 07:33:08 2010 : Using interface ppp1
    Tue Oct 19 07:33:08 2010 : Connect: ppp1 <--> socket[34:18]
    Tue Oct 19 07:33:08 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : lcp_reqci: returning CONFACK.
    Tue Oct 19 07:33:08 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : sent [CHAP Challenge id=0x18 <XYZ>, name = "myserver.private"]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : rcvd [CHAP Response id=0x18 <XYZ>, name = "user2"]
    Tue Oct 19 07:33:08 2010 : sent [CHAP Success id=0x18 "S=XYZ M=Access granted"]
    Tue Oct 19 07:33:08 2010 : CHAP peer authentication succeeded for user2
    Tue Oct 19 07:33:08 2010 : DSAccessControl plugin: User 'user2' authorized for access
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfReq id=0x1]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
    Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-NAK
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
    Tue Oct 19 07:33:08 2010 : Unsupported protocol 0x8057 received
    Tue Oct 19 07:33:08 2010 : sent [LCP ProtRej id=0x2 80 47 01 01 00 0f 01 0a 02 1b 63 ff fe a0 dd da]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x1 <ms-dns1 0.0.0.1> <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfRej id=0x1 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfAck id=0x1]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-ACK
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : ipcp: up
    Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:08 2010 : found interface en0 for proxy arp
    Tue Oct 19 07:33:08 2010 : local IP address 10.0.1.29
    Tue Oct 19 07:33:08 2010 : remote IP address 10.0.1.213
    Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x2 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfAck id=0x2 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSP data <payload len 26, packet seq 0, CI_DOMAINS, flags: START END REQUIRE-ACK>
    <domain: name XYZ>]
    Tue Oct 19 07:33:08 2010 : rcvd [IP data <src addr 10.0.1.213> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
    Tue Oct 19 07:33:08 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.213> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSP data <payload len 0, packet seq 0, CI_DOMAINS, flags: ACK>]
    Tue Oct 19 07:33:34 2010 : rcvd [LCP TermReq id=0x2 "User request"]
    Tue Oct 19 07:33:34 2010 : LCP terminated by peer (User request)
    Tue Oct 19 07:33:34 2010 : ipcp: down
    Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:34 2010 : sent [LCP TermAck id=0x2]
    Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:34 2010 : L2TP received CDN
    Tue Oct 19 07:33:34 2010 : Connection terminated.
    Tue Oct 19 07:33:34 2010 : Connect time 0.5 minutes.
    Tue Oct 19 07:33:34 2010 : Sent 777000 bytes, received 105388 bytes.
    Tue Oct 19 07:33:34 2010 : L2TP disconnecting...
    Tue Oct 19 07:33:34 2010 : L2TP disconnected
    2010-10-19 07:33:34 PDT --> Client with address = 10.0.1.213 has hungup
    Tue Oct 19 07:33:50 2010 : rcvd [LCP TermReq id=0x3 "User request"]
    Tue Oct 19 07:33:50 2010 : LCP terminated by peer (User request)
    Tue Oct 19 07:33:50 2010 : ipcp: down
    Tue Oct 19 07:33:50 2010 : sent [LCP TermAck id=0x3]
    Tue Oct 19 07:33:50 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.214).
    Tue Oct 19 07:33:50 2010 : L2TP received CDN
    Tue Oct 19 07:33:50 2010 : Connection terminated.
    Tue Oct 19 07:33:50 2010 : Connect time 3.5 minutes.
    Tue Oct 19 07:33:50 2010 : Sent 625383 bytes, received 225586 bytes.
    Tue Oct 19 07:33:50 2010 : L2TP disconnecting...
    Tue Oct 19 07:33:50 2010 : L2TP disconnected
    2010-10-19 07:33:50 PDT --> Client with address = 10.0.1.214 has hungup
    2010-10-19 07:33:59 PDT Incoming call... Address given to client = 10.0.1.216
    Tue Oct 19 07:33:59 2010 : Directory Services Authentication plugin initialized
    Tue Oct 19 07:33:59 2010 : Directory Services Authorization plugin initialized
    Tue Oct 19 07:33:59 2010 : L2TP incoming call in progress from 'XYZ'...
    Tue Oct 19 07:33:59 2010 : L2TP received SCCRQ
    Tue Oct 19 07:33:59 2010 : L2TP sent SCCRP
    Tue Oct 19 07:33:59 2010 : L2TP received SCCCN
    Tue Oct 19 07:33:59 2010 : L2TP received ICRQ
    Tue Oct 19 07:33:59 2010 : L2TP sent ICRP
    Tue Oct 19 07:33:59 2010 : L2TP received ICCN
    Tue Oct 19 07:33:59 2010 : L2TP connection established.
    Tue Oct 19 07:33:59 2010 : using link 0
    Tue Oct 19 07:33:59 2010 : Using interface ppp0
    Tue Oct 19 07:33:59 2010 : Connect: ppp0 <--> socket[34:18]
    Tue Oct 19 07:33:59 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : lcp_reqci: returning CONFACK.
    Tue Oct 19 07:33:59 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : sent [CHAP Challenge id=0xf1 <XYZ>, name = "myserver.private"]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : rcvd [CHAP Response id=0xf1 <XYZ>, name = "user1"]
    Tue Oct 19 07:34:00 2010 : sent [CHAP Success id=0xf1 "S=XYZ M=Access granted"]
    Tue Oct 19 07:34:00 2010 : CHAP peer authentication succeeded for user1
    Tue Oct 19 07:34:00 2010 : DSAccessControl plugin: User 'user1' authorized for access
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : sent [ACSCP ConfReq id=0x1]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
    Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-NAK
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
    Tue Oct 19 07:34:00 2010 : Unsupported protocol 0x8057 received
    Tue Oct 19 07:34:00 2010 : sent [LCP ProtRej id=0x2 80 57 01 01 00 0e 01 0a 02 1b 63 ff fe 99 35 cb]
    Tue Oct 19 07:34:00 2010 : rcvd [LCP ProtRej id=0x2 82 35 01 01 00 04]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-ACK
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : ipcp: up
    Tue Oct 19 07:34:00 2010 : found interface en0 for proxy arp
    Tue Oct 19 07:34:00 2010 : local IP address 10.0.1.29
    Tue Oct 19 07:34:00 2010 : remote IP address 10.0.1.216
    Tue Oct 19 07:34:00 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.216).
    Tue Oct 19 07:34:00 2010 : rcvd [IP data <src addr 10.0.1.216> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
    Tue Oct 19 07:34:00 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.216> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">]

  • I just installed CS4 and can only open one document at a time. Has anyone else had this problem?

    $

    Are you sure? Do you see different document names at the top of the window, like tabs in a browser?
    PS: ALWAYS tell us the version number (you did, good) and OS (you didn't, bad).

  • In photoshop elements 12 i try to select multiple people to view in organize but can only select one

    in photoshop elements 12 i try to select multiple people to view in organize but can only select one person at a time.  if I try to select two or more people to see their pictures, I get nothing.  I try to use CTL-click, but that does not work

    Hi,
    Try switching to Media view and then go to Find -> By Details.
    Set the field to People and select the persons name.
    You add further people by clicking on the + sign
    The two options above the search criteria allow you to select all photos containing at least one or only ones with all of your selections.
    The search can be saved in case you want to repeat it a later time.
    Hope that helps
    Brian

  • I have two apple accounts, but can only access one. I did all the steps to recover the older account's password but nothing worked. I need to access the older account to update apps. Also would there be a way to just combine both accounts?

    I have two apple accounts, but can only access one. I did all the steps to recover the older account's password but nothing worked. I need to access the older account to update apps. Also would there be a way to just combine both accounts?

    Were you able to reset the account's password ? If not then how did you try to get it reset e.g. http://iforgot.apple.com (which would have sent it to the rescue email address if you have one on that account) ? You can also try contacting iTunes Support in your country to get it reset : http://support.apple.com/kb/HT5699
    And no, accounts can't be merged nor content transferred between accounts.

  • Can only print one item at a time

    Hey everyone,
    Bit of a Photoshop novice here, use it for DVD covers and labels. I have been using CS3 previously but upgraded to CS5.5 last year. The thing is on CS5.5 I can only print one page at a time even when I input say 20 copies to be printed, only one will print. That goes for the regular printer for printing covers and the disc printer.
    I can open CS3 up and right away it will print however many I ask it to.
    Is there something I am missing? Something so painfully obvious that it is staring me in the face but I am just not seeing it?
    Thanks in advance!

    It isn't a printer setting. I have 3 different printers connected to my system and all of them worked with CS3 fine. And when I delete the preferences folder for CS5.1 it works as it should but only once, then afterwards it only prints one copy, no matter how many I ask it to print!
    So if it works when the preferences have been removed, then fails to work afterwards, how can that be a printer setting?
    I have read elsewhere that others have had similar issues with CS5 and Windows 7.

  • Database 'TEST' is already open and can only have one user at a time.

    Hi all,
    Could some help on this issue as per urgency!
    Database 'TEST' is already open and can only have one user at a time.
    I also tried this command but having the same error, please let me know how to troubleshoot this issue
    Use Master
    GO
    Select * from master.sys.sysprocesses
    Where spid > 50
                And dbid=DB_ID (‘StuckDB’))  -- replace with your database name
    Thanks

    Hi Tony,
    sorry got the same error again, it can't allow me sp_who2 as well
    I tried above command got the following error
    Changes
    to the state or options of database ‘TEST’ cannot be made at this time. The database is in single-user mode, and a user is currently connected to it.Msg 5069, Level 16, State 1, 

  • When downloading i can only download one link at a time per window. i used to be able to download six links at a time per page. how do i go back to this?

    got a new laptop. unsure of firefox verson on old as the computer quit taking a charge.
    but essentially on my old laptop if a window had six downloadable links i would be able to download all six at once. now i can only download one link at a time. this is very annoying. i do not believe it is an issue with the new laptop itself as it is a highend toshiba.

    Hello cherokeeguy, go to [http://kb.mozillazine.org/About:config about:config] find [http://kb.mozillazine.org/Network.http.max-persistent-connections-per-server network.http.max-persistent-connections-per-server] right-click on it, select modify and put a greater value, try 10 or 16, click ok to save it, exit firefox and restart it.
    BUT this normally should not happen !
    check it also in [https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Safe Mode], select '''''"Start in Safe Mode" '''''and see if this happen again, if not see: [https://support.mozilla.org/en-US/kb/troubleshoot-extensions-themes-to-fix-problems Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]
    also try to update to the latest firefox 16.0.1
    thank you
    Please mark "Solved" the answer that really solve the problem, to help others with a similar problem.

  • I lost my only navigation tool bar, so I can only open one window at a time, and can't use google. Help.

    I'm not sure what I did, but I right clicked on my google tool bar (which I use since I can't find the Firefox navigation toolbar) and I somehow disabled it. Now I can only use one window at a time, and if I go to a website, I can't go to another without closing my current one so I can go to my homepage, which is google.

    If the Menu Bar is hidden then press F10 or press and hold the Alt key down to bring up the "Menu Bar" temporarily.
    Go to "View > Toolbars" or right-click the "Menu Bar" or press Alt+V T to select which toolbars to show or hide (click on an entry to toggle the state).
    See also [[Menu bar is missing]] and http://kb.mozillazine.org/Toolbar_customization

  • Since installing an icon-editing add-on, I can't open tabs any more / I can only use one tab at a time.

    Ever since I installed the add-on Favicon Picker 2 that lets you change the bookmark icons, I can't open tabs any more. The second tab will open, but if you try to go to a site, the FIRST tab redirects to that site. Basically, I can only use one tab at a time. Is there any way I can keep this add-on and use tabs?

    Oh, wow - look at that, you're right :) I didn't want to uninstall the add-on as I like the feature, but simply by disabling it you can keep the new icons AND use tabs. Thanks dude!
    (The add-on is Favicon Picker 2 0.6.2.15 by the way - some of the user reviews report the same problem.)

  • I can only view one email at a time

    I can only view one email at a time when i open my email app

    Reopened this question in another forum, since I am not talking about an iPhone but a MacBook Pro:
    Using Mail, I have a very strange phanomenon: I can only open one email at a time. E.g. when writing a new email, I cannot open another email for reference. I need to close and save the new email as a draft before being able to open another one. Obviously, I am not reading two emails at a time, but I might be writing one and needing infos/text from another. It sounds stupid, but that's the way it is. :-/

  • Power View can only print one sheet at a time with Power BI Mobile Apps

    I have PowerView for Excel 2013 on Power BI Preview. I have 2 reports sheet and 2 hidden data sheets on Excel.
    I'm getting error on Mobile Application in Windows 8 RT tablet.
    I should see 4 reports in preview page, but I see 2 correct reports and 2 errors.
    Power View can only print one sheet at a time. Please switch to the desired sheet and try again.
    Why this occurs? What should done in Excel?
    Kenny_I

    Thank you for reporting this issue. This is a known issue that we had fixed last week. In a few days, the updated version of the app will be available in the Windows store. At that time, your app should automatically get updated to the newest version, if
    you have not changed your default settings.
    If you still experience issues next week this time, please post back and perhaps share your workbook, so we can do a thorough investigation.
    Thank you.

Maybe you are looking for

  • Select by focus not showing up in menu

    This is weird. I am running Photoshop CC 2014 and my image is an rgb 8 bit jpg and for the life of me I can't figure out why under the selection menu, the new focus area menu is absent. Supposed to be right under color range and it's just not there,

  • Animated symbol as a preloader ?

    I need some urgent help... there is any simple way to use an animated symbol as a preloader ? Thanks in advance

  • I want to do RS232(115200 braud rate) and 5 channel(100H

    z each) read simultaneously, what you think would be the best way. I have done some trials with the usual VIs you can find in demos however there is a delay which makes my RS232 data corrupted or my analog input read too slow to acquire the signal co

  • Documentation on execCommand and postMessage

    Hi, Where can I find documentation on execCommand and postMessage of the AcroPDF control (used from c#,WPF)? I am looking for a command which does search in the acro control and I am not successful at all.

  • Was anyone successful in creating a subscriber with test drive IAS 6 sp3 /IMQ2?

    I have been trying to create a subscriber to a topic in test drive IAS 6 sp3 /IMQ2. But have not been able to do so. I have created queue's and publishers though..I get an EXCEPTION_ACCESS_VIOLATION