2 problems with EA6300 both speed issue's

I got my EA6300 for a while now, overall for what it is used its doing ok.
Though recently i had to add a tv box to my network.
Connecting it to the router would not work, since it did not get a IP.
So i was forced to put a switch before the router.
So the network cable with the internet signal on it is first connected to the switch to which the tv box is also connected.
Then a cable supplying internet goes to the router, and another cable which is connected to my desktop pc.
Both router and switch are all gigabit ports, so that is one thing to rule out.
The PC is connected to the switch because if i connect it to the router then speed seems to be capped at 100mbit, while it should be capped at 1000mbit with the gigabit ports.
The PC network is gigabit also, and with a 100mbit cap i cap my internet also since it is faster then that.
So that is why i had to connect the PC to the switch.
Could adding a 4 port gigabit switch make the router cap the amount of speed it lets through?
Because this seems to have started when i added the switch, before that everything was fine.
Then problem 2.
To the router i got a external 2TB hard disk connected.
For whatever reason i cannot get any faster transfer rate then 2mb/s when moving files from desktop to the HD.
Most times it is just barely getting 1mb.
This is over the regular windows network, maybe that is the main issue?
Any help would be much appreciated.

Sevy wrote:
I managed to fix the speed issue from the router to the PC.
Though still unsure why wired the transfer rate is so slow.
From the drive to the desktop i get about 18mb/s which isn't to bad.
But from the PC to the drive its now getting just below 10mb/s.
Check if the slow wired transfer speed happens on all wired devices in the network. Upgrade the firmware of the router as well.

Similar Messages

Problem with the wireless speed on windows with bootcamp

I've got a problem with the following:
the wireless card of my mac pro is very slow when i run windows on my mac pro with bootcamp
When i just run OSX everything works fine, but in windows, when I connect to the wireless my wireless speed
drops to 11-18mbs.
First I thought that it was a drivers issue, but after the update of bootcamp drivers 1.4 the problem still exist.
First I had a Topcom wireless router now I've bought a Apple Airport Extreme, but the problem isn't solved yet...
The router isn't 2 meters away from my mac.
And the wireless speed is fine when i connect with my dads windows laptop...
Does anyone has a solution? using a cable isnt a solution for me because in September I will move with my mac pro one floor down.

You might want to ask this in the Boot Camp forums. As your wireless work fine under Mac OS X it sounds to be a software issue as opposed to a hardware one which means as Windows users they'll better be able to help.

Have have much problems with my both iphones 4gs and 3gs with coverage of the networks !!! Is there a solution for it

Hello Gentlemen ;
I have two iphones , one 4gs and one 3gs !
With both of the phone i have problems with the network coverage where other phones don't have problems !!!
Can i do something about this ?
Thx a lot

If you syncing both iPhones from same PC/Mac then first i will advice you to create a new User account(on your computer) then restore both devices and configure as new device( make sure you have a backup of both devices in the regular user account) this link may help you out http://support.apple.com/kb/HT4137, after doing so try using both devices with the data for say 24hours to see if you got same issue..if same issue the call apple phone support, or visit the closest apple store in your area..but if the issue is resolve after the restore and setting up as a new device then i will advice you to do a manual sync of all information(i.e don't restore from backup) hope this help's you

Problems with connection/download speeds

Since Friday evening we have been experiencing problems with our broadband connection. It's been disconnecting and when it is connected it is at a wide variety of speeds.
We found that we had noise on lifting the telephone receiver which was confirmed by doing the quiet line test. Tried connecting again by just using a filter into the test socket and directly into the hub but again we are finding the same issues with the broadband connection.
Thinking it might be a problem with our old hub we got the most recent model and have today tried connecting to broadband. As we were still getting the same problems (using our normal connection setup) we once again tried connecting straight into the test socket but still the problems remain.
I've included the ADSL stats below:
Connection Information
Line state:
Connected
Connection time:
0 days, 00:17:48
Downstream:
832 Kbps
Upstream:
352 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
16.5 dB / 6.0 dB
Line attenuation (Down/Up):
42.1 dB / 31.5 dB
Output power (Down/Up):
17.5 dBm / 11.9 dBm
FEC Events (Down/Up):
15 / 6
CRC Events (Down/Up):
8 / 5
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
6 / 0
Error Seconds (Local/Remote):
176 / 97
Speed test info is:
Download speedachieved during the test was - 135 Kbps
For your connection, the acceptable range of speeds is 50-250 Kbps.
Additional Information:
Your DSL Connection Rate :832 Kbps(DOWN-STREAM), 352 Kbps(UP-STREAM)
IP Profile for your line is - 135 Kbps
These results are from being connected to the NTE5 master socket (test socket) via cable.
Any help would be appreciated.
Thanks

Hi welcome to the forum
As you have noise on the phone line that needs to be resolved first you need to phone BT Faults on 151 and report a noisy line but do not mention broadband once the noise is fixed your broadband will improve
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Is anyone else having a problem with a "no service" issue on the iPhone 5?

There are times my phone will go to "No Service" when the signal is low. I just got the iPhone 5. I did not have this problem with my 4. It doesn't say "searching..." it just automatically says "No Service" for a few seconds and then back to having bars. It comes and goes. I had my phone replaced at the Genius Bar and still have this problem. Is anyone else also having this problem? I hope it's just a software issue they will solve with an iOS update.

I have this problem all the time. when i get back home from a overseas trip (about 3-4 times a month) I have to turn airplane mode of and on a few times to get rid of the "No Service" message.

MSI CD53, i5 750 - Problem with CPU Fan Speed

Hello
I have problem with this counfiguration: i5 750, MSI CD53 Motherboard.
I Have processor overheating poblem. I noticed that processor easly can go up to 90C.
I check phisycal installation, and all its ok.
After that i check RPM of CPU FAN and i noticed that it cant go over 1000 RPM, so propably this is problem.
In MSI Control Center maximum i can set 1000 RPM.
I read that CPU FAN can go up to 3000 RPM.
Maybe i have something wrong set up in bios? What can i do with this?

Quote
CD53
Which board exactly do you have?
What is your current BIOS Version?
What kind of CPU-Fan are you using (3-Pin or 4-pin PWM (four wires) and which connector is it attached to?
What are your current fan speed/control settings in BIOS Setup?
Quote
I check phisycal installation, and all its ok.
Physical installation is one thing, but what about thermal paste (have you used a PROPER amount (too much thermal paste has the opposite effect))?
What about your case ventilation?
Quote
I noticed that processor easly can go up to 90C.
Please check the CPU's core temperatures with CORE TEMP, REAL TEMP or HW-MONITOR!

Strange problem with broadband. Speed very low.

Hi all,
From last Friday I encountered really big problems with my broadband as the speed go dramatically down. I don't know what may be the reason, I'm using HomeHub and between it and computers in my household everything is fine. I haven't heard about any fixes round Aberdeen so have completely no clue what is going on.
Do you have any clue what can cause the problem, for more than 3 years everything was just great. Maybe my HomeHub is old and faulty, it is the 1st gen, white one.
I post speedtest results and ADSL info:
Download speedachieved during the test was - 134 Kbps
For your connection, the acceptable range of speedsis 4000-21000 Kbps.
Additional Information:
Your DSL Connection Rate :18761 Kbps(DOWN-STREAM), 888 Kbps(UP-STREAM)
IP Profile for your line is - 16000 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 0.0:75.22:25.5 (SBE:NBEBE)
These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
Upload speed achieved during the test was - 692 Kbps
Additional Information:
Upstream Rate IP profile on your line is - 888 Kbps
DSL Connection
Link Information
Uptime:
3 days, 22:26:20
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
888 / 18,762
Data Transferred (Sent/Received) [MB/GB]:
350.53 / 4.65
Output Power (Up/Down) [dBm]:
11.5 / 0.0
Line Attenuation (Up/Down) [dB]:
4.5 / 14.0
SN Margin (Up/Down) [dB]:
15.0 / 5.0
Vendor ID (Local/Remote):
TMMB / IFTN
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
0 / 0
FEC Errors (Up/Down):
0 / 246,017
CRC Errors (Up/Down):
0 / 46
HEC Errors (Up/Down):
0 / 39
Line Profile:
Fast
Solved!
Go to Solution.

Update.
First, do you always get reply from MODS? Today my connection dropped and after a while it was on again, I found my SN Margin reset to 6.5 and better bandwith 1205 / 19832 but the speed didn't improve at all. It is 24h since I've sent notice to MODS and I will wait another 24h before contacting them again. What really worries me is FEC Errors field in my ADSL Line details. Last time after 4 days it was 245'000, now after 6 hours I have more than 750'000. Is that normal after connection drop? I've checked speed using this speedcheck provided and my profile is still the same, 16000kbs
UPDATE:: 40 minutes past, 35 MB more dowloaded and 100'000 FEC Errors more :/
I paste details below:
DSL Connection
Link Information
Uptime:
0 days, 6:01:26
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
1,205 / 19,832
Data Transferred (Sent/Received) [MB/MB]:
38.53 / 275.66
Output Power (Up/Down) [dBm]:
12.0 / 0.0
Line Attenuation (Up/Down) [dB]:
4.5 / 14.0
SN Margin (Up/Down) [dB]:
6.5 / 4.0
Vendor ID (Local/Remote):
TMMB / IFTN
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
1 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
1 / 0
FEC Errors (Up/Down):
0 / 769,697
CRC Errors (Up/Down):
0 / 8
HEC Errors (Up/Down):
0 / 5
Line Profile:
Fast

Problem with adjusting both transparency and color of an object

I am writing a program where when an object is picked, both it's transparency and color will be altered (the object will become opaque, and its color will turn to a predefined "selected" color), while the previously selected object will return to its original transparency and color. I am able to get this to work, except that objects that were picked two or more picks ago will remain in the selected color, albeit in their original transparency. This problem only seems to occur when transparency is factored in. The picking/color & transparency altering code is as follows.
public class PickingListener extends MouseAdapter {
     private PickCanvas pickCanvas;
     private TextDisplay overlay;
     private Primitive p;
     private Primitive lastP;
     private ColoringAttributes origColor;
     private TransparencyAttributes origTransparency;
     public PickingListener(PickCanvas pickCanvasArg, TextDisplay overlayArg) {
          pickCanvas = pickCanvasArg;
          overlay = overlayArg;
     public void mouseClicked(MouseEvent e) {
          pickCanvas.setShapeLocation(e);
          PickResult result = pickCanvas.pickClosest();
          if (result == null) {
               System.out.println("Nothing picked");
          } else {
               p = (Primitive) result.getNode(PickResult.PRIMITIVE);
               if (p != null) {
                    setSelectedColor();
                    overlay.setPickedBarInfo((BarInformation) p.getUserData());
               else
                    System.out.println("null");
     private void setSelectedColor() {
          ColoringAttributes barCA = new ColoringAttributes();
          TransparencyAttributes barTransp = new TransparencyAttributes(TransparencyAttributes.NICEST, 0.0f);
          barCA.setColor(ColorConstants.SELECTED);
          if (lastP != null) {
               lastP.getAppearance().setColoringAttributes(origColor);
               lastP.getAppearance().setTransparencyAttributes(origTransparency);
          origColor = p.getAppearance().getColoringAttributes();
          origTransparency = p.getAppearance().getTransparencyAttributes();
          p.getAppearance().setColoringAttributes(barCA);
          p.getAppearance().setTransparencyAttributes(barTransp);
          lastP = p;
}Capabilities to alter the primitive's color and transparency are all set.
     barAppearance.setCapability(Appearance.ALLOW_COLORING_ATTRIBUTES_READ);
          barAppearance.setCapability(Appearance.ALLOW_COLORING_ATTRIBUTES_WRITE);
          barAppearance.setCapability(Appearance.ALLOW_TRANSPARENCY_ATTRIBUTES_WRITE);          barAppearance.setCapability(Appearance.ALLOW_TRANSPARENCY_ATTRIBUTES_READ);
ColoringAttributes barCA = new ColoringAttributes();
barCA.setCapability(ColoringAttributes.ALLOW_COLOR_WRITE);
barCA.setCapability(ColoringAttributes.ALLOW_COLOR_READ);)
Any insight as to why this would occur would be greatly appreciated.
-Adrian Benton

A Behavior is the preferred way to make changes in a scenegraph. Here is an example from a previous post that changes the appearance of a shape when it collides with another shape.
The javadoc for javax.media.j3d.Behavior appears to refer to the issue you have.
Transparencies are confusing, different display adapters deal with them differently. Suggest you search the forum at
http://forums.java.net/jive/forum.jspa?forumID=70
for more detailed information.
regards
class CollisionDetector extends Behavior {
private static final Color3f highlightColor = new Color3f(0.0f, 1.0f, 0.0f);
private static final ColoringAttributes highlight = new ColoringAttributes(
      highlightColor, ColoringAttributes.SHADE_GOURAUD);
private boolean inCollision = false;
private Shape3D shape;
private ColoringAttributes shapeColoring;
private Appearance shapeAppearance;
private WakeupOnCollisionEntry wEnter;
private WakeupOnCollisionExit wExit;
public CollisionDetector(Shape3D s) {
    shape = s;
    shapeAppearance = shape.getAppearance();
    shapeColoring = shapeAppearance.getColoringAttributes();
    inCollision = false;
public void initialize() {
    wEnter = new WakeupOnCollisionEntry(shape);
    wExit = new WakeupOnCollisionExit(shape);
    wakeupOn(wEnter);
public void processStimulus(Enumeration criteria) {
    inCollision = !inCollision;
    if (inCollision) {
      shapeAppearance.setColoringAttributes(highlight);
      wakeupOn(wExit);
    } else {
      shapeAppearance.setColoringAttributes(shapeColoring);
      wakeupOn(wEnter);
}

Problem with Web Gallery (firewall issue??)

I have the following problem:
When I upload a webgallery from my office, everything works fine.
When I try the same thing from home, it doesn't work. I get a can't connect to .mac error.
What I also found out:
Looking at my .mac preferences from the system preferences panel works at home and at the office.
Looking at the web gallery tab under preferences in iphoto works ONLY at the office. At home I get a time out eventually.
Anyone have an idea? I do have a rather transparent network on both places.
Thanks!
Martin

ma_nj:
Welcome to the Apple Discussions. Try deleting the iPhoto preference file, com.apple.iPhoto.plist, from your User/Library/Preferences folder on you home computer. Then try again.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 08 libraries. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Is my laptop the problem with slow usb3 speeds?

I'm sporting a dv6-7200ea system, as standard, and have bought a toshba stor.e Basics 2tb USB 3.0 portable hard drive.
Toshiba state that it is capable of 5gbit speeds whereas the maximum i can attain is 100mb (1gbit?).
I have asked toshiba directly and they say the problem lies within my laptop, not their hardware.
Is this true? If so, what causes it??

Unfortunately, Your notebook model does not have the extra space for a second SATA hard disk. I checked in the Maintenence & Service guide for your notebook series to see if if did. Models like the Envy17-3002ea, which I am currently using as a loaner, are optionally equiped with a pair or 750 GB hard disks.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Problem with WRT160NV2, both wired and wireless...

I bought a WRT160NV2 Refurbed from CompUSA about 2 weeks ago, and since then I've been having some problems.
It's not every site, but there are a few sites (three or four I've noticed) that load very, very, very slowly. It happens using wired or wireless (Main PC is wired). I've tried rebooting both the router and modem multiple times (10 or 20 times at least) and looked through the forums and noticed some people said try setting the MTU to 1300. I tried that and it didn't seem to do anything, so I tried 1350, 1400, 1450, 1490, and 1100, with no results with either. When I connect using just my modem everything works fine. I'm frustrated because I can't find a solution to this. Any help would be appreciated.
Firmware Version: v2.0.03 build 007 ;Jul 2, 2009
Message Edited by RagingShadow07 on 02-27-2010 01:48 PM

Since you have already changed the MTU size on your Router and still facing the same problem, then i think you need to Re-flash / Upgrade the firmware of your Router...
Download the firmware from the Linksys website and then upload the firmware on your Router... Once the firmware is upgraded on your Router, then you need to reset the router and re-configure all the settings on it again...

Sound Problems with Need for Speed Most Wan

Hello There:
I have a ZS 2 Creative sound card. Everything (windows media player, half life2 and etc.) was working fine. After installing the NFSP most wanted game the sound does not work any longer with any software or games !!! All softwares and games work but no sound !!!
Is there a compatibility issue with creative sound card and NFSP most wanted? I have updated my sound card driver from Creative web site alsready. After un-installing the game and doing a system restore teh sound is back now !!!
Your comments would be great.

hmm....sounds more like a directx problem.....is the game installing any directx stuff?

Line input problem with Logic X, No issues Logic Pro

I use the line input on my 2011 Imac to record audio from my piano keyboard. When using LOGIC X there is no sound coming through the speakers, but with Logic Pro 9 I have no issues. I tested with new projects, ect but was unable to get to work.
In both Logic Pro and Logic X I have made an audio track and made sure input monitoring is on. I made sure volume was sufficient. I have tried to fix this to no avail and was thinking about bringing to apple store, but this appreasrs to be some sort of logic x bug (or I am missing something). Any help is appreciated as this is very frustrating.
Brian

I think you're missing something.
http://help.apple.com/logicpro/mac/10/#lgcpbb81aca5
You have to configure each program top to bottom, go to the above link and make sure all your settings are correct. (the won't necessarily match the pic)
Look at your Logic 9 settings Preferences/Audio and then set up Logic X the same way.

Re: Strange problem with broadband. Speed very low...

What is going on with my BT Broadband speed...?
Download 0.25 Mbs and up load of 0.09 mbs..
This just can't be right...?
Frustrated subscriber.. Glenn :-(

I moved you post to start a new thread as previous one was marked as solved by originator
welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you post the adsl stats from your router may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or use a-z, if netgear enter 192.168.0.1) and run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results .
are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

MSI ti 4200 128 MB and Problems with "Need for Speed: HighStakes"

Does any one know of a fix for "Need for Speed: HighStakes" with the new 45.32 drivers. When trying to start this game it won't even load, the screen goes dark for a second and then falls back to the desktop. Did the same thing with 43.45, but if I install the drivers that came with the Video card ( I think they were 31.XX) then the game works fine. Haven't come across any other games that won't run except this one, some examples that work fine are UT 2003, C&C: Generals, Warcraft 3, Hot Pursuit 2.
System:
XP pro OS (sevice pack 1) DirectX 9
Athlon 1800
512 MB RAM
MSI nforce 2 Main board
MSI GeForce 4 4200 ti 128 MB 8X AGP
Thanks for any info.

well I "bugged" the game makers (EA) and the response is that the game doesn't suport Windows XP. Strange that the older nVidia 31.xx drivers work fine with the game. Also played it on my last machine which had XP and a ATI radeon video card. OH well who ever said Direct X was supposed to be backward compatible.
Too bad the older drivers don't work so well with the newer games.

2 problems with EA6300 both speed issue's

Similar Messages

Maybe you are looking for