2" Vertical Black Border on my desk-top

What have I done for this 2" black border on the left side and right side of my desk-top to show up? Why did it happen and What can I do to un-do it?

Also, are you using a desktop image which is not in the right ratio for your display?
If that's not the case try resetting your pram/nvram.
-mj

Similar Messages

Black screen on apple desk top will not power on. I can here some sound when I try to turn on. Help?

How do I fix black screen home pc will not power on?

If you hear the start up sound try a PRAM reset and a static discharge.
First unplug your Mac from power.
Press and hold the power button for 30 seconds.
Release.
Press the power button 5 times.
Plug back in to power.
Turn it on, and hold CMD OPT P R on your keyboard until you hear the Start Up Chime a second time.
Michael

Black border blocking top of screen

Since the iOS 7.1.1 update a black border with the time/battery/sim blocks the top of my games. Does anyone know how to get rid of the border?

How did you import your clips? From analog tapes?
I quote F Shippey:
"You are probably see a line or two of sync pulses from the ANALOG video. They are normally masked off-screen by the overscan others have talked about. (In fact that's one reason for the overscan - to hide these pulses.)
In the "old days" - when TV sets had vertical and horizontal hold controls - you could adjust the vertical hold to make the picture roll and see several lines of such "junk".
You won't see them when the video is viewed on a TV from a DVD or DV tape. You will see them on your computer."

Have a problem with my MacBook Pro.5,3 and monitor. Intermittently, the desk top screen becomes broken up into vertical sections, which appear in the wrong order, creating a haphazard picture. The Apple icon, usually at top left corner, appears in to

have a problem with my MacBook Pro.5,3 and monitor. Intermittently, the desk top screen becomes broken up into vertical sections, which appear in the wrong order, creating a haphazard picture.
The Apple icon, usually at top left corner, appears in top right corner in a strip including all that left hand. When the computer is restarted, the screen goes back to normal. But I have to move the mouse to the far left of the screen and then up until it reappears on the far right hand side of the screen so that I can hit shut down button.
It seems to happen randomly though always on desk top and sometimes when I move mouse and computer switches on from rest mode. My large flat screen is relatively new.
The video card on this computer, which is approximately two years old, is Nvidia FeForce 9400M.
Any help would be welcome as my usual source of assistance is not available and I am not well versed in workings of the Mac although I have used one for many years.

That sounds like a Hardware problem.
You may be able to confirm that with Apple Hardware Test, or make an appointmenst for a free Genius Bar evaluation.

How to remove a black border box that continously tabs to each field automatically till end of web page; restarts to top of page, cannot stop this box. Scroll bar cannot controlled with mouse, returns auto to top of scroll slide, never remaining at bottom

how to remove a black border box that continously tabs to each field automatically till end of web page; restarts to top of page, cannot stop this box. Scroll bar cannot be controlled with mouse, scroll bar returns automatically to the top of scroll slide every time I move the bar to the bottom of the scale. Also, there's a rectangular text box (with black background and white text) that is always on the desktop that emulates a typed text, HTML, or cmd function.

cjuan1morb4ulv wrote:
how to remove a black border box that continously tabs to each field automatically till end of web page; restarts to top of page, cannot stop this box. Scroll bar cannot be controlled with mouse, scroll bar returns automatically to the top of scroll slide every time I move the bar to the bottom of the scale. Also, there's a rectangular text box (with black background and white text) that is always on the desktop that emulates a typed text, HTML, or cmd function.
The first two problems (box cycling from element to element on page, scroll bar returning to top) can be caused by a stuck (or defective) Tab key on the keyboard. Such damage can be caused by a liquid spill; just one tiny droplet is enough to short a wafer switch under one key.
The last issue (black box, white text - sounds sorta like a debugger window) I haven't seen, but could be caused by something similar.
To check for that, try using a different keyboard. If you're using a wireless keyboard, turn it off and see if the oddities stop.

My Black Berry Desk Top Manager doesn't work on my computer help!

On March 6 I took my BlackBerry® Style™ 9670 smartphone in for software issues after tech support did a hard reset on the device. I went home to back up my information and was unsuccessful. The connection failed this is the first time that the desk top software had problems. I un-installed The Desktop software and reinstalled and the disk that came with the phone open almost "1 Million" windows therefore opening some type of virus on my computer. I tried to install from the Black Berry site and it did the same thing. I had to get my computer serviced, I tried installing from the site yet again and now it still isn't working when installed... Help!!

Hi luciana247,
Welcome to BlackBerry Support Community Forums.
Can you provide more detail on what happens with the Desktop Software after the last reinstall? What error messages are being received? Are you able to open it? At what point does it stop working?
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

I have a black box always open on my desk top , telling me what commands i am doing . it started when i pushed all the keys on my keypad !

i have a black box always coming on my desk top , telling me every command that i am doing , it happened when i pressed all the keys on my keyboard.

Hi Josh,
Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
Thanks.
Mike Towns

LG Flatron L245WP-BN monitor is cut off at top and has a black border at the bottom of the screen

LG Flatron L245WP-BN monitor is cut off at top and has a black border at the bottom of the screen. Connected to HP Pavillion laptop via an HDMI cable. Is there any way to align the monitor so the full screen is showing?
Please help!!
Thanks
This question was solved.
View Solution.

navers wrote:
Sorry! It is an HP Pavilion 15 Notebook PC. I can give you the product number if you want? Running on Windows 8.1 64-bit
Thank you for the additional information.
Yes, the product number would be helpful. Please don't provide the Serial #, however.
I believe your problem may be that the monitor is not compatible with Win 8.1. The only updates that are available are for Win XP and Vista. You can find this information in the link that I provided under the section titled "Software Update".
I suggest contacting LG Customer Service to see if they can help you.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Black border around an inset clip?

I've done a movie with a little inset clip on the bottom left (comes in after about 5s).
https://www.youtube.com/watch?v=gB7oiBo1v0M
I want to put a black border around the inset clip - as can be seen I've done this (I know I need to remove the drop shadow).
But the vertical border on the left is narrower in width than the horizontal border across the top.
I've seen another movie by someone else where all the borders are the same width.
Just wondering how to do this as I couldn't see relevant controls in the generator's inspector..
I used the Shapes generator, btw. Set to rectangle, no fill, black border.
It's a bit of a fiddly process getting it to fit - is there a better way?

Ah, that's just what I was looking for - thank you!

Black border after rendering

My video is perfect while I'm working on it but every time I hit Enter to render it does render, but also all of the video clips jump a little, creating this black border around them all on the top and sides. I can fix it by adjusting the anchor point or position one notch, but I have to do that for every clip and then of course the "rendered" line turns red again. This seems like a bug. Here's a screenshot showing this border:

OK, I'm not quite sure what you are doing, when you are adjusting:
when I make that fix, suppose the number is at 243 (as it was in the test I just did) and to fix it I raise the number to 244. Now I hit Enter to render. The black border appears, but the number is still at 244.
Your Project/Sequence is 720 x 486, which appears to be the largest Frame Size of any of your Assets. Are the Sequences in the Project each set to the Frame Size of the contained Assets, or are you using Motion>Scale to fit them into the 720 x 486 Sequences?
Where are you using the 243 and 244? Is this in the Effects Control Panel>Effect>Motion>Scale, vertical dimension setting, or elsewhere.
It's probably that I am just not following something in the workflow, and not something that you're doing, but I'm not clear on a few aspects.
Thanks,
Hunt
[Edit] I think I just got it. You are inputting the 243 into Motion>Position for the center of your Asset. Sorry, it took a moment to sink in.

How do I remove a black border from my 4:3 ratio movie, which only uses 4:3 ratio images?

Hello,
I'm using Adobe Premiere Elements 9. I have an audio file from a teleconference call and I am using images exported from a 4:3 PowerPoint presentation to create a video of the presentation. The image files are .tiff files, 960x720. This is the only type of file I am using to create this video.
I really need to get rid of the large black border which appears on ALL sides (left, right, as well as top and bottom) whenever I export. Exporting as flv, mpg or avi has no change. I also tried .png images, no change. Any ideas??
Thanks!

My guess is that the 1280 x 720 was the last Project Preset used, and was still there, when you chose New Project.
As for your output, will you be outputting an SD (Standard Def), or HD (High-Def) file for uploading?
Do you ONLY have the TIFF Still Images, or are you mixing in any Video?
The Frame Size difference, between the 960 x 720, and the 1280 x 720 will cause black borders. The two choices are to use the 1280 x 720 Project, and then use Motion>Scale to increase the Scale of your TIFF's. Note that the Aspect Ratio of those TIFF's does not match the 1280 x 720, so to get rid of ALL black borders, you will Scale up the TIFF, and effectively crop your TIFF's. If there is no margin on your TIFF's, that can be a problem.
As PrE only supports standard Video Frame Sizes, there will not be one that matches the 960 x 720.
Good luck,
Hunt

HP Desk top Model # 500314 Sleep Mode/Moniter will not wake up

HP Desk Top Model 500314- Windows 8.1 OS.
PC will go into sleep mode but after approx 15/20 minutes when I want to wake it up the PC wakes up but the moniter will not wake up(just a black screen).
I have reset the power settings numerious times with all variations! same results. It is strange that the sleep mode works fine for the first 15 to 20 minutes and then the problem appears?
All other aspects of the PC seem to be working alright. This is a new PC about 2 months old and the problem appeared from the first time it was turned on. All the latest Drivers and Windows updates are installed. HELP!

Hello @larhoop,
I understand that you are having issues with your HP Pavilion 500-314 Desktop PC running Windows 8.1 not waking up properly after being asleep for 15-20 minutes. I am providing you with an HP Support document: Troubleshooting sleep and hibernate issues in Windows 8, which has been designed to address issues such as the one you are facing. The steps for Windows 8 and 8.1 are the same so review the document and apply the steps set out within.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Step by step text box appeared on desk top

I have this box that appeared on my desktop - it is a rectangular shape but with rounded corners. It is a black screen with with text and a white frame. It types out exactly what I am doing on my computer - for example just them it typed out "computer" after having finished typing out the word. If I click on a desk top folder it reads "Finder Desktop and gives the name of the folder" - it's really annoying and I cannot figure out how to get rid of it. Please help! Thank you!

Turn off VoiceOver in the Universal Access or Accessibility pane of System Preferences.
(83681)

How can I automatically crop a photo based on its content (a black border)?

I scanned hundred of negatives.
The scanner produced .jpg files. Most of the scanned images show the negatives holder to one side as a black border. The black border is thicker or thinner depending on the photo.
Please see pictures attached.
Is there a way to automate the detection of such a border and remove it by cropping the photo? Ideally I would like the processing to only remove the thickness that is required to keep the photo unaltered as much as possible.
I have Photoshop 12 and I know about Actions. I just don't know how to tell the engine to only crop if it is required, and by how much.
This could save me days of manual work. Thankyou.
Environment Information:
· I am running Photoshop 12.1 *64 bit
· Windows 7 Professional 64 bit
· Amount of installed RAM: 6GB
·       Scanner: Canon CanoScan 8800F
· Amount of free disk space:
            C:\ - OS and Software disk - Total size:139GB showing 20GB free
            G:\ - Data disk - Total size:1.81 TB showing 437GB free
· Make/Model of Video Card: NVIDIA GeForce 9600 GT

Thank you miss marple for your Image>Canvas Size... suggestion. I used it to implement a semi automated process.
I programmed a couple of actions:
- one to trim all sides by 7 pixels
- one to trim the top side by 7 pixles
Then I assigned a shortcut key to each action.
Since I have to open each photo individually anyway to remove larger scratches (see my other post), it is easy to hit a couple of keyboard keys to trigger the relevant 'border removal' action.
The main thing is that in 95% of cases I don't have to use the mouse to fix the borders, but I use keyboard keys only. It is a real time saver.

How to achieve black border around a logo

Hello,
I am trying to do a parody of a Top Gun logo and have it done except for the border around the image. I know this is probably very simple and I've googled it but can't figured it out.
Here is an example:
http://www.redbubble.com/people/tgigreeny/works/7360099-top-gun-sundown-with-tomcat
I want to create that black border/background colour and can't figure it out.
Thanks for any help you can offer.
Mary

Well actually it is a bit more complex than I wrote
1 You have to outline the text and
2. united it with the art (color bars that hbe the same color)
3. you have to give the object a stroke and drag it below the fill in the appearance panel
4 the jet plane needs a fill of white
5. the star needs a stroke with the stroke being draged below the fill in the appearaqnce panel
6. then you group everything and give the group a sufficent weight stroke cover all the gaps
7 and finally you drag the stroke you gave the group below the contents in the appearance panel (that means it is behind the groups contents the logo art.
Like such ( You have to think this one out.)

2" Vertical Black Border on my desk-top

Similar Messages

Maybe you are looking for