2 x Airport Extreme's or 1 Extreme + Express? Config Help Please!

Hello,
I have just purchased the MacBookPro Retina and want to reevaluate my WiFi setup.
My current configuration:
*Baement* > Cable Modem --> Airport Extreme [5th Gen] ---- Cat 5e ---> Switch GB ---> Netgear G AP > *study*
There are a few other Wireless G rated AP's around the house.
Do you think I should get another Airport Extreme for the study? or should I go for the new Airport Express - The Extreme is 3 Stream, can use 5GHz
I have a 120/mbit Cable Connection, so the Express throughput may be limited?
Can I use a second Extreme just as an AP?
Thanks guys,

If you plan to connect a hard drive to the "new" AirPort that you will be adding, the AirPort Extreme will support a USB hard drive, the AirPort Express will not.
If you do have a 120 Mbps connection, then the AirPort Extreme would be the better choice as well since it has Gigabit Ethernet ports while the Express is limited to 100 Mbps.
While the Extreme does have 3 LAN ports and the Express 1, you could always add an Ethernet switch to either device if you need more connection points.
Finally, the AirPort Extreme has the better antenna package, so if your budget permits, another AirPort Extreme would be the logical choice for use as an access point.
Configure the Extreme to "create a wireless network" using the same wireless network name, same security settings and same password as the "main" AirPort Extreme and be sure to configure the "new" Extreme in Bridge Mode to work correctly on the network.

Similar Messages

  • Hard Drive makes Airport Extreme Restart. HELP PLEASE!

    It's been more than a month since I startes trying to tackle this problem, now I'm pulling my hair out. My small 60GB Lacie (non powered) works fine, mounts, etc. but my big WD 320BG Lightes Combo makes the Extreme's status light go solid amber when I turn it on.
    So, after reading a thread, I formatted the drive to Mac OS Extended. The drive then did nothing, and it appeared in the Airport utility. However, when trying to mount the disk, either with airport disk utilit or manually, back to the same ols story, the Base Station's light goes solid amber and I lose te network.
    So the problem isn't the file format. It has to be something to do with the disk. But I had it replaced by WD yesterday and I have a new one! No change.
    could anyone please suggest something? has anyone experienced the same problem?
    Thank-you

    A little update... spoke to Apple Care... they said that this happens and then are aware that this happens, but had no answers how to fix.
    Unfortunately not much help... anyone else have any information?
    Please help!

  • I am unable to see my Airport Extreme/Express on my MacBook via Airport Utility

    I have two issues:
    1. I am unable to see my Airport Extreme and my Airport Express via my MacBook Air's Airport Utility when I scan for Base Stations. However, the computer is happily connected to the wireless network of my Extreme (the Express is used to extend range)
    2. I am unable to see a HDD that is connected via USB cable to the Airport Extreme.
    Any suggestions welcome.
    Thanks

    Further info:
    Setup
    MacBook Air running OS X 10.5.8
    AirPort Extreme Base Station
    AirPort Express used to extend range
    AirPort Utility v5.5.3
    The MacBook Air is actually connected to the wireless network provided by the two AirPorts!
    Oddly, I see both AirPorts just fine when using my older PowerBook G4 with an older version of the AirPort Utility.
    In addition, I cannot see the external HDD connected to the AirPort Extreme Base Station, and my wireless printer (HP D410a) suddenly stopped working via the MacBook Air. However, it works just fine from my iPhone, which is connected to the same AirPort Extreme/Express wireless network.
    Recently, at the request of Sky Broadband, I switched to fixed IP addresses instead of DHCP, as I was having issues with the DHCP set-up.

  • Wireless constantly disconnects using Airport Extreme & Express

    I am so frustrated, my internet has always worked fine up till just a few days ago when it started acting strange now it just constantly cuts out. Im using an Airport Extreme (4th Generation) and an Airport Express (2nd Generation) the way I have it set up is all run through ethernet by Powerline Adapters. I have the Express extending the Airport Extreme. Any help would be greatly appreciated. Here is a screen shot below of my Wireless settings for both the Extreme and Express they are both the same exact settings

    Blazer12345, Welcome to the discussion area!
    I am coming to the conclusion that the Extreme is doing me no good being that my G4 won't or can't use any of the 802.11n advantages. Correct?
    It can't use 802.11n but it can use the USB printer and/or USB hard drive connected to the AirPort Extreme base station (AEBS).
    Would a low signal be the reason that is why it is being interrupted?
    Yes

  • Few questions about Airport Extreme/Express

    I have a few questions about Airport extreme/express:
    1 Can you access hard drive trough express?
    2 I have cable NOT wireless modem. What would be the best option (speed-wise) to connect to internet- connect modem to Extreme and access internet wirelessly from it? To connect modem to Extreme and imac?
    3 How fast is read/ write from hard drive connected to Extreme?
    4 How many hard drives can you connect to Extreme (or Express if that is possible)?
    5 Can you remotely sync Ipod nano/ shuffle using Extreme?
    I really hate wire clutter around my desk. What I intend to do is to connect hard drives and printer to Airport Extreme and access them remotely. That would leave empty desk:).
    Thanks

    1. You cannot connect a hard drive to the Airport Express USB port.
    2. The speed of wireless networking is faster than the speed of most cable internet services. Therefore, you won't notice any difference in your internet connection speed between (a) a cabled connection directly between Mac and modem or (b) a wireless connection between Mac and base station and modem.
    3. Apple has not published any specs on the speed of hard drive access for the Airport Extreme N Base Station. Several people have posted their own measurements (do a search in this discussion forum), and generally those results are not very good.
    4. Apple has not placed a limit on the number of drives you can attach to the Airport Extreme N Base Station (with use of a hub). How many do you want to connect?
    5. You cannot remotely sync an iPod using the Extreme Base Station.

  • My Macbook Air does not pick up wifi from Airport but iMac, iPad and iPhone do. Help please.

    My Macbook Air does not pick up wifi from Airport but iMac, iPad and iPhone do. Help please.

    Are you testing in the same room as the TC?
    Power cycle the TC.. does it show up now?
    Has it ever showed up .. ie is this a problem that just started from an existing setup, or has never worked?
    Is the TC new? If old how old?
    If you continue to have issues.. setup the TC from iMac and preferably using ethernet.
    Change the wireless names to SMB compatible ones, short no spaces, pure alphanumeric.
    Use WPA2 Personal security only.
    Then set the wireless channels manually.. try 11, 6, 1 for 2.4ghz and try 36 or 40 at 5ghz.
    Tell us how that goes.

  • AirPort Extreme Network Setup Help

    Currently I am using my AirPort Extreme to create a wireless network for two houses. The problem I have is the devices in the other house have problems with the base station being in 802.11N so I had to force it into 802.11G only. What I would love to do is setup a device at the other house that connects to my AirPort Extreme using the N standard and then connect all of those devices over there with ethernet cables so I can use N at my house. Are there any devices that I could do this with?

    I was kinda hoping there maybe another solution besides spending another $180+

  • Airport extreme & express - I am tearing out the little hair i have left !!

    Can anyone help with this problem before i am completly bald.
    I have just bought a new imac (with intel chip) and i am wanting to locate it downstairs but the room is in a wireless deadspot.
    I have a pc upstairs connected to a bb cable connection. I have now replaced my belkin wireless router with an airport extreme base station and an airport express to act as a booster for the imac downstairs.
    i have installed the extreme base station ok and it works for the pc which is hard wired to it and wirelessly for the imac when in range. I am having problems trying to set up the airport express as a relay station.
    Every time i configure the extreme to act as a wds and then add the airport express it cuts off the pc connection and the imac, I must not be doing the settings correctly in the airport admin - is it something to do with sharing ip addresses ??
    I have followed the instructions on this site but still having probs - can anyone offer help or guidence please
    Thanks
    imac intel 2ghz 250g   Mac OS X (10.4.4)   extreme base station airport express

    Thanks for your great advice and assistance. I have read the various articles that you linked and will try the new extended configuration using my old 4th gen as soon as my new 5th gen extreme arrives from Apple. I may also try using the express as well by going off in a somewhat different direction on the upstairs floor where the primary base unit is connected to the cable modem. My original reason for upgrading to the new 5th gen was not because the range and signal strength were inadequate, but rather to try and get some improvement in the wireless download speeds from the 4th gen extreme and the extended express. My Mac  using an Ethernet connection from the extreme was delivering download speeds of 49 to 50 Mbs all the time, while the wireless download speeds to my new iPad or my iPhone 5 were only about 15Mbs coming from the extreme and 7-8 Mbs if I was downloading through the express. I have been reading lots of comments on this subject for over a year now, with many others experiencing the same problem, but Apple never really acknowledging that there was even an issue. The only solution seemed to be that people who upgraded to the 5th gen. we're getting much better performance across all performance issues. Here's hoping for success in the next few days. Thanks again for your assistance.

  • On a network with multiple airports (extreme, express, + time capsule), do they all have to be "guest" capable devices in order to offer guest networking?

    Here's the situation: I have three older devices:
    a1254 Time Capsule
    a1134 airport extreme
    a1264 express
    none of these support guest networking, according to Apple. If I add a newer Extreme (3rd gen or higher) that support guest networks, will that be possible to offer to guests within range of the Extreme, -OR- do I have to upgrade my entire network of Apple wifi devices? Help appreciated, esp if you have such a setup. thanks!

    The problem here is guest network only works if the Apple Router is indeed the main router.. you cannot setup guest network on a bridged router. Although it appears you can, it doesn't actually work.
    You could modify the network setup..
    Use one device dedicated to a secondary guest network. This would actually work better than using guest but you should have some way to prevent access to computers from guest.. that may be easy or hard depending on the modem you are using.

  • Help in Planning Network: G5/iBook G4/Airport Extreme & Express?

    Hi  Folks,
    I could use some help setting up a WiFI network to accomplish three goals (see below).
    Hardware and Software:
    Computers
    -Dual Core 2.3 GHz PowerPC G5 Desktop Computer (note: NO internal airport WiFi card), OS 10.4.11
    -iBook G4 with internal Airport Card (currently with dead HD, awaiting a replacement HD any day). Can't remember is this has an early version of OS10.4 or 10.3.
    Airport
    -Airport Express 802.11n (MB321LL/A,  model #A1264)
    -Airport Extreme base station model #A1034 (older unit with 2003 date)
    -Airport Card internal card in the iBook G4
    Airport Software loaded on my G5:
    -Airport Admin Utility v5.4.2
    -Airport Disk Utility v1.5.3
    ** I do NOT have Airport Setup Assistant software on the G5, nor can I locate it on the OS install disks that came with the G5.
    Network Goals:
    Previously, I've setup a simple WiFi network in my apartment by using only the Airport Express: I connected the DSL modem to the Airport Express and transmitted the WiFI internet signal to the iBook. I haven't had that setup for quite some time; recently I was given the Airport Extreme and I'd like to finally get a network up and running.
    I have a roommate that wants internet access so I'd like to setup a WiFi network to accomplish as many of the following three goals as possible:
    1) Wifi internet capability.
    1a) G5 wired connection to DSL modem/Airport Express as my primary internet connection and for fastest speeds (again, no WiFI card in the G5).
    1b) Transmit WiFi internet signal so my roommate can share internet access, but for security purposes limit my roommate from accessing any data/files on my computer(s).
    1c) WiFi internet access for my own G4 iBook.
    2) WiFi file sharing network
    2a) Wireless network so that my G4 iBook can access data/files from my G5 (private network roommate excluded).
    3) Stream iTunes.
    I have my iTunes library on an external HD, currently connected to my G5. I'd like to broadcast iTunes music to another room. Can the Airport Extreme stream iTunes from my G5 (the latter with no internal Airport Card) to another room where the Airport Express is connected to another stereo receiver/speakers? If yes, can I use my G4 laptop as an iTunes remote control to make music selections?
    Question: Can all (or most?) of these goals be accomplished with the hardware/software on hand?
    .... so....
    Currently, I plugged in the Airport Extreme connected with an ethernet cable to the G5 (using the  connection with the  <- ->  symbol on the Airport Extreme). The G5 doesn't identify the  Airport Extreme, which makes me think I need the AIrport Setup Assistant Software?
    In any case, I'm lost as to how to configure this setup to accomplish my goals. I've owned Apple since 1994 but haven't delved far into setting up networks.
    Any guidance and help would be tremendously appreciated!
    Thanks a bunch,
    Lovegasoline

    Bump.
    Can anyone offer some basic guidance?
    Do I need Airport Setup Assistant software to configure this network?
    Thanks.

  • Airport extreme, express,and iTunes

    I have a 1.33ghz iBook, an airport extreme base station and an airport express that I have configured to use to play itunes through my stereo at home. when I jack my ibook directly into the stereo ituns works flawlessly, but when I play itunes wirelessly through the network the program keeps pausing for up to about 5 seconds. The program will then resume playing by itself picking up right where it left off, as far as I can tell. I also have a wintel xp machine at home that is connected directly into the airport extreme, and it does the same thing. Any ideas?

    Thanks, I found the topic at "audio drop while using airtunes". Now I only wish that after spending the money to buy the gear that apple adveritsed to have an airtunes network, that it actually worked without having to come up with some jury rigged set up. This kind of stuff is why I switched from wintel last year to apple

  • Windows 7 machine unable to connect to WDS (Airport extreme + express)

    Hi - I've just dusted down my old Airport Extreme (b/g) and Airport Express to extend the range of a Sagem Mini Livebox router (that we use because it gives internet telephone and tv feeds here in France).
    The AExt has an ethernet connection to the livebox and is set up as the main WDS machine; the AExp is connected wirelessly to the AExt as a WDS relay station. It all works fine - I've set the airport wifi network up with a different name to the main livebox wifi network, and can access it using my Mac machines all over the house. But my wife has a Windows 7 machine that she uses for work ... and it fails to see the airport network (but is able to connect to the livebox wifi without any problem).
    I don't know Windows 7 very well, and there seem to be very few options that you can configure. The wifi adaptor is a Dell 1390 (only b/g connections according to an online manual); but the old airport boxes only support b/g compatible connections, so that should work.
    I've set up a wireless network on the W7 machine that matches the airport profile: WPA personal security ... but my understanding is that this will not change whether the W7 machine can see the airport network (but only affect how or whether it connects).
    Not sure what else I can do? Any thoughts on how I can reconfigure my airport WDS network so that the W7 machine can see it (and connect to it)?
    Thanks - andy

    Are you trying to configure the Express to "join" the wireless network?
    If yes, the message you are receiving is likely an indication that you do not have the correct security settings selected for the Express. Unless the security settings between the wireless router and Express match up exactly, the Express will display the error that "an error occurred, etc".
    The easiest way to confirm if you have this problem is temporarily set the main wireless router to "no security" and try to connect the Express that way. If you can connect, then you know that it is a security issue.
    Please tell us the exact setting for security that the wireless router there is using and we'll try to give you some more ideas.
    The Express will connect. It's just a matter of finding the right settings.
    Message was edited by: Bob Timmons

  • Airport extreme, working config, visible from win7 NOT from winXP

    I've got a new extreme that I configured with windows 7 (bridging mode, hard drive, AirPort Utility 5.6.1) which is
    all fine but when it's invisible from Windows XP (SP3, APU 5.5.3).  The XP version of the APU software does
    not see the device at all nor the hard drive.  However, I can map to it from the command line with net use e: \\192.168.0.8\drive0
    where it asks me for a user name (!!!!) and a password.  I provide the disk password and my XP user name (cringe)
    and it's working fine.  I'm connected to it via wireless and I'm actually running a backup to it right now without
    trouble.
    What the heck is wrong?  I don't really want a stealth configuration for my XP machines.
    Thanks.

    Cool; I will try that. Thanks!
    I was told that the wifi card in the base goes bad after a bit; problem is: nobody sell it....and I can't really afford a 200 dollars airport extreme base nowadays
    Can't complain, after almost 6 years it is still alive after all. But I need WiFi at home; 90% of my devices are WiFi

  • Using Windows 7 Remote Desktop with Airport Extreme...help!

    I recently purchased an Airport Extreme to replace an old Linksys router I had. Its works great, but I'm having an issue when I send my brother a remote desktop assistance link in Windows 7. We are both running Windows 7 and never had this problem in the past, but now that I'm using an Airport Extreme it wont connect. Tech support could not provide the correct ports that needed to be opened. I'm thinking it has something to do with NAT PMP (Apple) and UPNP (Microsoft). We have opened ports 3389 and 491152 - 65535 but no luck.
    So my question...how can I enable the Airport Extreme to allow Windows 7 Remote Desktop Assistance?

    Sorry, that should be remote "assistance" not "desktop"

  • Web Sharing with Leopard 10.5.2 and Airport Extreme Base Station HELP!!!

    Ok...I want to set up web sharing on my computer but so far my attempts have failed.
    I have an intel iMac with Leopard 10.5.2 installed and I have the latest Airport extreme base station (With draft n).
    I turn on web sharing, and of course it works locally but not when trying to be accessed over the internet.
    Now I realize that by default my routers address wont let anyone connect to my computer over the internet.
    My router has an ip of 10.0.1.1, and I assigned my computer a static ip address of 10.0.1.200.
    Now in the network preferences pane and the airport category, i set my computers IP (the 10.0.1.200), I put the gateway as 255.255.255.0, the router as 10.0.1.1 and the DNS as 10.0.1.1
    Now going over to the airport utility I added a new entry in the port mapping section, with port 80 (both public and private) and the IP of my machine, 10.0.1.200.
    Now in theory this should work but NOOOOO.
    Does anyone have the same setup? a wireless network with the new airport extreme base station and has successfully configured Web Sharing?
    Thanks in advance.
    Felipe

    Well here is an update.
    I saw an entry in apple support that said I had to change some setting in the apache folder /etc/apache2 in order to avoid getting the 403 forbidden error. I tried this and it did not work, i checked my user configuration file as well and the path to my home site directory was correct
    Anyone here have a similar setup and has it working? It shouldnt be too hard to set up web sharing through a router. It has to be possible or else a lot of people would not buy a router because of this.
    thanks in advance to anyone kind enough to help
    Bye.

  • Problems transfering files from PC to Harddrive on Airport Extreme.. Help!

    I upgraded to an Airport Extreme to help speed up my wireless and access a LACIE 1tb harddrive between two computers - a Windows XP 64bit machine and a new macbook.
    Everything works great except I cannot copy large files from the PC to the harddrive even though I can stream movies off the harddrive to the same computer and transfer small files. When I try to copy a large file I get "The specified network name is no longer available" after about 30sec even though its actually connected (I can browse and watch a movie after I get the error). The large files do show up on the HDD after getting the error but they are not working files. So frustrating.
    I have read that it could be the 7.4.2 firmware but have tried going back to 7.4.1 with the same results. I have also tried backing up the Airport and restoring to default settings. Also tried installing the airport software on the PC with no luck. I am considering trying to format the drive from FAT32 to the default apple one but really don't want to do this.
    Anyone have any suggestions? This is got to be the most frustrating problem I have encountered since starting my mac transition...

    So I plugged in another 250gb hdd that I have lying around, formatted with my macbook and successfully backed up over 130gb worth of files via time machine. Also, tried transferring some "large files" to the same drive via the PC with blazing speed and everything works great.
    So it turns out that a harddrive with FAT32 doesnt work properly with a PC.
    I will be formatting my other 1tb drive now and I suspect will have similar results but this issue is odd and frustrating to say the least.

Maybe you are looking for