2008 mbp boots up with weird pattern on the screen
2008 mbp boots up with weird pattern on screen then says needs to restart but won't restart. Saw something about nvidia graphic card went bad and apple was replacing for free. Is that something apple is still doing and does that sound like my issue?
I know this is an old post, but people reading it may be interested by these two links:
http://totalpoop.com/apples-2008-macbook-pro-nvidia-graphics-card-recall.htm
http://support.apple.com/kb/TS2377
I got this problem with my previous 2008 Macbook Pro, and it appeared just after the recall ended! Here in Canada, Apple is charging close to $500 to replace the motherboard (and the graphics card). Recently, I discovered a computer chop in Montréal where they told me they can replace the GPU for $200. I left them my computer and will get it back in a week or so. I hope it will fix the problem.
Similar Messages
-
I have just purchased an iphone today and it is coming up with a picture on the screen of the usb connector and itunes symbol. It also says that I now have no service and can only make emergency calls
Just a thought, but maybe consider returning the device. Seems it might be a bit too complicated for you.
-
Intel iMac; upgraded adobe flash; bluetooth keyboard no longer pairs but magic mouse still OK. With Bluetooth switched on the screen splits into 4 areas and open windows seperate and shrink. Switch off Bluetooth and problem disappears and iMac works OK with plug-in keyboard and mouse
Hi, Derek -
...the screen splits into 4 areas and open windows seperate and shrink.
Sounds like Spaces is being activated somehow. With the wired keyboard and mouse in use, select the Exposé & Spaces control pane in System Preferences, click the choice in that pane for Spaces. See what the settings are. There are some activation settings in that pane - by default, F8 activates it.
It could be that the bluetooth keyboard has some stuck keys and is activating Spaces; or that the activation command has somehow been reset to something that the bluetooth mouse, or bluetooth itself, is triggering. -
While browsing the internet with my iPhone 4S the screen goes black and it looks like it's turning off, but it pops up to the unlock keypad screen. It has plenty battery and I was wondering if it is an issue of using too much of the iPhones RAM or not. I have no other apps open besides Messages. I am getting kind of worried as it started around two weeks ago and it has gotten increasingly frequent.
Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these steps in order until the issue is resolved.
-
I have updated my Iphone5 with new IOS6 - now the screen/display does not react to my taps on screen as in i cant tap in my pin to startup???
I have updated my Iphone5 with new IOS6 - now the screen/display does not react to my taps on screen as in i cant tap in my pin to startup???
-
Problem with InDesign CC redrawing the screen too slow while using Zoom tool
Hello. I got a problem with InDesign CC redrawing the screen too slow while using Zoom tool. Sometimes it takes more than a secong to zoom in or out. However InDesign CS6, Photoshop CC, Illustrator CC works just fine. What could be the problem, videocard or something else? Below is my PC configuration: OS Windows 8 Pro (x64); processor Intel Core i7 2600k CPU 3,40GHz; video adapter NVIDIA GeForse GTS 450; monitor NEC PA271W (2560x1440).
Yes it’s a bug. The trick is to select the tool and then left click the photo information strip and hold for a few seconds until you see the windows bar at the top of the screen (not responding)
The lasso tool should then work normally. -
Hi friends, I'm having troubles with my Ipad 2. I was working with it and suddenly the screen distorted. Now it is not possible to get it back to work properly. In fact, the screen is now black and nothing I have done makes the Ipad works again. Please Help. Thanks in advance.
I think you should make an Genius Appointment.
Genius Appointment
http://www.apple.com/retail/geniusbar/ -
My macbook pro keeps freezing with vertical lines on the screen
I have a 2010 macbook pro that has worked wonderfully until now. As of late it keeps freezing with vertical lines across the screen. To me this indicates a hardware problem, but I ran a diagnostic (restarted while holding D) and it didn't find any errors. It seems that it happens when I move or bump my macbook, leading me to think it may possibly be a disk problem, but I'm not sure how to check this. Anybody else ever have this problem or could suggest a fix for it?
You can try a pram reset, which might help with the display, but the bumoing thing is what concerns me.
PRAM reset:
Power down, power back up and hold the following keys before the start up chime.
option, command, P, R,(no commas) continue to hold these keys till you hear the start up chime 2 times then release.
Reboot see if this helps, the bumping part scares me.
Hope this helps -
My iPad is frozen with a message on the screen that says "iCloud backup is full" and it gives me the option of cancel or settings but will not go to either one or allow me to exit the message. How can I restart? It will not let me turn off or doesn't help to plug into computer
Try a reset:
Hold the Sleep and Home button down until you see the Apple logo.
Data will not be affected. -
I plugged my Ipad3 in order to update the software to version 6.1 but I got an error message and my Ipad is locked now, it's showing the Itunes logo with USB cable on the screen. What should I do now?
You will probably need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Or you can follow these Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
With remote management enabled the screen saver never kicks in, the monitor never sleeps
The title says it all. With remote management enabled the screen saver never kicks in, the monitor never sleeps. This is with an iMac. So I have to leave remote management off, which means instead of using remote desktop I have to manage the machine with TeamViewer. Life is still good, but this seems like a bug, and there's a few things remote desktop does that TeamViewer can't.
You should use a specialized tool such as TextWrangler, the Property List Editor, or the defaults command in the Terminal to view and change plist files; those created with recent software are encoded so that a regular text editor will not properly parse them.
(33430) -
Hi yesturday,i was tranfering my photos of my phone to my computor,and the phone has froze on me,i cannot switch the phone on or of,what i can see on the screen,is the itunes logo with a cable on the screen,its looks the one you put the cable into one of the ports,there is no way possible to switch of or on please help,im stressed out lol,thankyou francis01224
Aug 15, 2012 8:28 AM (in response to EricaP1234)
Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
Hi my Ipad shows that ITunes icon along with connection wire on the screen...I cannot access anything else, what should I do?
About recovery mode : http://support.apple.com/kb/HT1808
Have you made any backups of your data via iCloud btw? If not, you will loose your data :/ -
I have the iPad with retina display and the screen is cracked, however it is not yet a year old, how much does it cost to replace it?
I don't know what country that you are in, but in the US the price for repair (i.e. replacement) is (from here) $299 for the iPad 3, and here in the UK (from here) £256.44
-
My iMac starts up with vertical stripes on the screen
My iMac starts up with vertical stripes on the screen, does anyone know what it could be?
My issue is Blue Strips on start up and its frozen at Grey screen forever > I only successfully log-in on SafeBoot mode only actually while I'm typing this
been looking for solutions until came through your posted , ITS HELP! :-) Thanks to you!
so turn out mine was the LCD or Cable like you said,
What should i do from now ? already been tried many solutions :
Clean installed , PRAM , AHT ,
iMac (27-inch, Late 2009)
OS X Yosemite (10.10.2)
Please, Any suggestion ?
Maybe you are looking for
-
I had my iTunes account synced with an old e-mail account. I no longer remeber my password for this account and no longer have access to this e-mail account. I was able to change my information to a new e-mail in iTunes and iCloud with no trouble but
-
How to show Months of a Year as Parameter in Reports
Hello, Please tell me the method that "How can i use Months of a Year as Parameters in a Reports" Thank you in advance
-
Streaming from a Guest Account
Hello, I am wanting to have a friend watch a live stream from my mac connected with HDMI cable to my TV. I can get to safari, get to the web page, in this case ESPN2. However, live stream only gets as far as "loading." I never get it loaded. So, I at
-
Adding indexes to a table is slowing down query performance.
I am running a query against a table which contains approx. 4 million records in it. So I created 4 indexes on the table and noticed that the performance on my query drastically decreased. I went back and began remove and creating the indexes in diff
-
Excluding Datamember from Update in Parent-Child hierarchy
Hello, I have a Parent-Child hierarchy and writeback enabled measures. If I make an equal allocation update on a parent element, its datamember gets the same amount as the leaf elements. How can I override this feature (scope and cell calulation for