2010 error on T43 with new HD

This is a continuation of an earlier post about my T43 being slow after standby - the HD was dying so I went ahead and installed a WD Scorpio Blue EIDE 160GB 5400RPM hard drive. It works fine as far as I can tell except for encountering the 2010 error message on start up.
As I found out reading previous posts on the 2010 issue, this has to do with the fact that I didn't buy a drive from Lenovo,i.e. "one especially designed for Thinkpad" (which, in my mind, sounds like a lot of bs to be frank).
I'd like to know if there is a consensus on whether the 2010 error can lead to loss of data and/or corruption of the drive OR if it is ok to keep bypassing the error?
Any thoughts?

FWIW, I've got a Seagate drive that I've been moving around for about 18 months now through several T43/p units, error is there, but there has been no data loss/corruption or any other side effects.
Hope this helps.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

Error running reports with new OMS

Hello All,
We had a bunch of reports scheduled in Grid Control. After migrating to a new OMS on a new server, reports are not being sent anymore.
I've done some tests and the error I see is this:
This is a scheduled report. The most recently generated report completed with the following error. Error: Unexpected occurred while e-mailing report: - null
The report is a simple one showing waits in terms of I/O, instance activity etc..
If anyone has ideas, let me know.
Cheers.
P.S. Preferred credentials are set and work fine. This is OMS 10.2.0.5 on Solaris 10. The target instance is a 9i instance.

I checked with both Mozilla and IE. Issue is not related to browser.
The problem seems to be information isn't available on host - If i go to the host- CPU/Memory/IO utilization show - No data is currently not available. I'm not sure if this is because of the 10.2.0.5 release but suspect that's the case since the data was available on 10.2.0.3 GC.
If anyone has seen issues where host metrics aren't showing in GC 10.2.0.5, let me know. The host is running solaris 9. GC is on solaris 10/Repository is at 11.1.0.7.
Thanks

Error Message working with new Nano and iTunes

Posts: 15
From: Petaluma Ca
Registered: Aug 29, 2004
Unlock iTunes / get write permission
Posted: Dec 26, 2006 6:02 PM
Reply Email
Wanted to upload some songs from my iTunes Library to new Nano.
Hooked it up, went through the promps, choose two playlists to load, and before we could say oops, we saw that it was infact loading the entire library. We had no way of stopping the process so we unplugged it.
Now when I try to open iTunes it I get an error message :"The iTunes Library file is locked, on a locked disk, or you do not have write permission for this file."
I verified permissions and repaired them. No luck.
Help! Please!

i'm assuming the Error code HRESULT: 0x800763b3 means something and is the solution but where can i find the answer or am i going about this all wrong?
Yeah, this 0x800763b3 is a slightly unusual one. Normally with these, the iTunes install error code matches the error codes that people get on their Windows Update failures. But for the last two 0x800763b3s I've been involved in on an iTunes install (Liv and someone else), the 0x800763b3 on the iTunes install has been associated with an 0x8007000b on the Windows Update failures. (Liv's 643s were pretty much "generic" error message codes for Windows Update failures, which could mean anything. So that's why I/we went after the 0x8007000b, which has some Microsoft documentation on fixes.)
Doublechecking on other symptoms of your situation ... is your Windows Update not opening at all when you try to launch it?
If so, when you click "Turn Windows features on or off" in the "Programs and Features Control Panel" item, is the Windows Features dialog box empty? (No features are shown?)
(If we can't get the codes from the windows update failures, we might be able to make some progress if we can identify other symptoms that you're getting. I know some documentation for some of these codes that mentions the Windows Features thing as a possible additional symptom.)

Error Message 2001 with new ITunes 8 (for Mac) & IPhone 2.1

Same general subject as many of tonight's posts. I updated to ITunes 8 & IPhone 2.1. There was some sort of problem during the latter update and my phone now has the "Cord &ITunes logo" with no emergency switch. When I connect the phone to the Mac through a USB, ITunes says that a recovery was stopped and that I must recover. So I hit recover but before the recover finishes it replies with Error message 2001 that it couldn't complete.
This occurred on a relatively recent Mac. My only goal is to get the phone working - I'll restore my settings and sync the music later.
Thank you
Tom

I don't have that same problem, I was able to download the new Ipod Touch software, but now that I have iTunes 8 and the new Ipod Touch software, it won't let me sync my Ipod. Any info would be great. When I try I get this message:
The Ipod "Matt's Itouch" cannot be synced. An unknown error occured (13213).
This just started happening this afternoon (I downloaded everything this morning.

SP 2010 - Error when creating a new Search Service Instance

Hi experts,
I'm getting the below error logged in my SharePoint 2010 SP2 Server. Any ideas to resolve it please? Thanks in advance.
Application Server Administration job failed for service instance Microsoft.Office.Server.Search.Administration.SearchServiceInstance (9b011033-0dc6-4d77-8f22-c16aa010532f). Reason: Exception from HRESULT: 0x80040D23
Technical Support Details: System.Runtime.InteropServices.COMException (0x80040D23): Exception from HRESULT: 0x80040D23
at Microsoft.Office.Server.Search.Administration.MSSITLB.IGatherManagerAdmin3.get_ConfigurationVersion()
at Microsoft.Office.Server.Search.Administration.Gatherer.ProvisionGlobalProperties()
at Microsoft.Office.Server.Search.Administration.SearchServiceInstance.Synchronize()
at Microsoft.Office.Server.Administration.ApplicationServerJob.ProvisionLocalSharedServiceInstances(Boolean isAdministrationServiceJob)
Hamza Grandi

did you see any error in Event/application logs? could you please tell us at what point you getting the error?
mostly this is happen when An index corrupted, may need to rebuild / reset the index.
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

Error Opening iTunes with new install

I just reinstalled iTunes onto my father's Dell laptop running Windows XP SP2. I recieve the following error message when trying to run iTunes for the first time: "The folder 'iTunes' cannot be found or created, and is required. The default location for this folder is inside the 'My Music' folder."
Any help would be greatly appreciated as i cannot run iTunes on this PC.

Try holding down the shift key as you start itunes, and create a new library when given the chance.

Exchange 2010 SP3 RU6 - Problems with New-MailboxExportRequest

New-MailboxExportRequest seems to ignore -ExcludeFolders and -IncludeFolders and export the entire mailbox. For example:
New-MailboxExportRequest -IncludeFolder TestExport -Mailbox TestUser -FilePath \\SomeUNCPath\test.pst
will exportsthe entire contents of the mailbox. I believe this used to work before, but it is possible I have lost my mind.
The folder TestExport is on the root, as in, if you were to run Get-MailboxFolderStatistics, the FolderPath is /TestExport. I've also tried using -ExcludeFolders to exclude every other folder with no luck.
Any confirmation of an issue or help is appreciated.

Hi,
From your description, I recommend you use the following cmdlet to check the result.
New-MailboxExportRequest -IncludeFolders "#Inbox#" -Mailbox TestUser -FilePath
\\SomeUNCPath\test.pst
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Java error when connecting with new sql developer 3.1

3.0 worked fine. I over-wrote the old version. so i need to see if i can find it to download.
do i need to download a new version of java? I did the full download which included java. the install nstuctiions(on the download page just say to unzip the file.
java.lang.NoSuchMethodError: oracle.dbtools.parser.LexerToken.parse(Ljava/lang/String;)Ljava/util/LinkedList;
     at oracle.dbtools.raptor.query.QueryUtils.matchesAnyPrefix(QueryUtils.java:349)
     at oracle.dbtools.raptor.query.QueryUtils.prependDbaVersion(QueryUtils.java:336)
     at oracle.dbtools.raptor.query.QueryUtils.getQuery(QueryUtils.java:298)
     at oracle.dbtools.raptor.query.QueryUtils.getQuery(QueryUtils.java:226)
     at oracle.dbtools.raptor.query.ObjectQueries.getQuery(ObjectQueries.java:42)
     at oracle.dbtools.raptor.navigator.xml.XmlObjectFactory.createFolderInstance(XmlObjectFactory.java:47)
     at oracle.dbtools.raptor.navigator.xml.XmlTypeOwnerInstance.listTypeFolders(XmlTypeOwnerInstance.java:74)
     at oracle.dbtools.raptor.navigator.TypeContainerFilter.loadTypeFolders(TypeContainerFilter.java:110)
     at oracle.dbtools.raptor.navigator.ConnectionFilter$1.doWork(ConnectionFilter.java:160)
     at oracle.dbtools.raptor.navigator.ConnectionFilter$1.doWork(ConnectionFilter.java:104)
     at oracle.dbtools.raptor.backgroundTask.RaptorTask.call(RaptorTask.java:193)
     at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:303)
     at java.util.concurrent.FutureTask.run(FutureTask.java:138)
     at oracle.dbtools.raptor.backgroundTask.RaptorTaskManager$RaptorFutureTask.run(RaptorTaskManager.java:515)
     at java.util.concurrent.Executors$RunnableAdapter.call(Executors.java:441)
     at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:303)
     at java.util.concurrent.FutureTask.run(FutureTask.java:138)
     at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886)
     at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908)
     at java.lang.Thread.run(Thread.java:619)

Hi,
For products whose install only involves an unzip, never over-write a previously installed version. From the 3.1 download page:
To install Oracle SQL Developer 3.1 download the file, there is no in-place upgrade available, you must unzip the file into an empty folder.
Regards,
Gary
SQL Developer Team

User profile sync Sharepoint 2010 photos thumbnail with AD and Lync 2010 - error on Full Synchronization- get events 8311, 6110, 6803 FIMSynchronization Service

User profile sync Sharepoint 2010 photos thumbnail with AD and Lync 2010 - error on Full Synchronization- get events 8311, 6110, 6803 FIMSynchronization Service
We're trying to set up sync between Sharepoint and AD so photos are displayed in Lync.
The certificate referenced in 8311 is not the sharepoint root cert, its the UCC cert with our FQDN of the site. sharepoint.domain.com
Is this causing the problem with the sync and holding up the photos?
I have tried several proposed fixes, it hasn't helped.
tried this as well:
http://blogs.technet.com/b/praveenh/archive/2011/05/11/event-id-8311-certificate-validation-errors-in-mss-2010.aspx
Josh

Try this fix and see if its sync the photos:
http://blogs.technet.com/b/steve_chen/archive/2010/09/20/user-profile-sync-sharepoint-2010.aspx#Profile Picture Property
http://blogs.technet.com/b/steve_chen/archive/2010/09/20/user-profile-sync-sharepoint-2010.aspx#SyncPicAD2SPS
Update-SPProfilePhotoStore -CreateThumbnailsForImportedPhotos 1 -MySiteHostLocation <mySiteHostURL>
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

When opening my Outlook 2010 with new added e-mail account with Exchange Server, I have to click manually on my standard e-mail account for checking mail

When opening my Outlook 2010 with new added e-mail account with Exchange Server supplied by my employer, I have to click manually on my standard e-mail account for checking mail. Do I have to upgrade my Microsoft Office 2010 or how can I make my Outlook
2010 check all my four e-mail accounts without manually click on my accounts?
Sincerely
Ketil Hothorp

Hello Ketil,
Good Day...
Seems to be the Issue is Syncing emails, now I would recommend you to Remove and Add the Account and try and check if the emails are getting synced automatically.
Hope this is with Single User. If it is with Multiple Users then we need to check the permissions assigned.
Regards,
Praveen

B2 Error with new MSI GTX 970 :(

Hi there team!
Just registered to try and get help. I spent around 6 hours researching + trying all the suggestions throughout many different forums, but the B2 error still persists. I am currently running the following spec:
Mobo - MSI Z68A-G43 (G3), with version 4.30 ( I flashed bios last night and still no help)
CPU - Intel® Core™ i5-2500K Processor, 3.5GHz etc.etc.
RAM - Corsair Vengeance 2x4gb at 1333MHz
GPU - MSI GTX 970 GAMING Twin Frozr V 4GB GDDR5
PSU - Cooler Master Silent Pro 700W
I have tried:
-Taking out the card and using the on-board graphics to flash the bios to later version, No help. (during this process, the B2 error does NOT show up)
-Upgraded the card to latest nVidia drivers, even uninstalled and re-installed them. No help.
-Upgraded all the drivers from MSI, i.e. chipset etc. through Live Update 6. No help.
When the card is in, I cannot even access bios, it just gets stuck at B2 screen for like a minute, and then carries on with the boot process. I am able to play games etc. after the booting, but this error for sure should not be there when the PC boots up. I didn't have any issues with my old GTX 560 TI. I've read different forums saying that it might have something to do with the mobo thinking that something has to be connected to the on-board graphics; or that flashing BIOS helped a lot of users, but not me :(.
I don't have a second PC to test the card on.
Literally, I would try anything, please someone just help :(( This card is a beast and I wanna be able to properly use it and not having to worry about this error.
Thank you very much guys, hope someone can help!

Quote from: gabe_dimitrov on 08-February-15, 20:40:51
Man thank you so much! It is finally working!!! Thank you!!!! ))) It is showing correct version in BIOS, does not show B2 error whatsoever, all done! )
Thanks for your time! You can close thread, but it's very useful for anyone that has this issue!
Wich version of BIOS do you have installed? Can you OC your processor with new BIOS?

HT1553 I did the back up as instructed... Installed a larger hard drive and followed the restore instructions... Now I get a white screen with a folder icon and blinking question mark. When trying to set startup with new drive I get a bless tool error...

I did the back up as instructed... Installed a larger hard drive and followed the restore instructions... Now I get a white screen with a folder icon and blinking question mark. When trying to set startup with new drive I get a bless tool error... Help!!

If you have installed a new hard drive , you will need to have formatted it in Disk Utility correctly. This may explain your problem.
Boot into your 10.6 Install disk again at the top menubar > Utilities > select Disk utility and in there select your new hard drive, and select the tab Erase and choose to make the format as Mac OS Extended Journaled. When that is finished look in the main window to make sure that the partition map scheme says GUID Partition Table.
Now go to the Restore tab and reinstall from your backup.

Can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

Yes. Any standalone display which can be connected to a Mini DisplayPort, with or without an adapter, can be plugged into a Thunderbolt port without any additional adapters.
(65766)

" 3 items could not be synced. See iTunes for more information" I have searched and I have tried the solutions on the forum. My iPhone has been successfully synced without error and I am trying to sync with new laptop.

" 3 items could not be synced. See iTunes for more information" I have searched and I have tried the solutions on the forum. My iPhone has been successfully synced previously on my mac mini without error. I am trying to sync my iPhone with new MacBook Pro.

Modular77: With respect the dialog on the iPhone 'XX items could not be synced. See iTunes for more information.' , would you happen to know where to look in iTunes? I looked in all the places that seemed logical to me.
I am, however, asking only for future reverence, as the initial sync which generated the error dialog was done via USB, and almost immediately after the USB sync, I ran a WiFi Sync—two in a row in fact—both initiated from the iPhone. Both WiFi syncs completed successfully with no error dialog.
I then ran another USB sync initiated from iTunes on the Macintosh, as was the first sync which gave the error. This second USB sync also completed successfully with no errors.
I think someone in this thread mentioned non-AppleStore products or DMR issues which I think could not have been an issue in my case, as I was running the sync to install updated Apps from the AppStore, and additionally had deleted some music and movie items to make sure there was room for the App updates. Nothing was added other than the recently downloaded App updates from the AppStore.
iPhone3GS iOS 5.1.1 build 9B206.
          Developer Profile enabled. iCloud enabled.
          32 GB “disk.” About 1.5 GB free after sync.
          iPhone NOT jailbroken
MacBook 13-inch Aluminum, Late 2008 (NOT Macbook Pro)
     Lion 10.4.7 build 11E53. 2 GB RAM.
Thanks for any info or advice. Problem IS now solved, but it absorbed a lot of time to reach that point.

How to export "Managed by" field of Distribution and Security groups and import with new values? (Exchange 2010, AD 2003)

My Active Directory environment is 2003 functional level and we have Exchange 2010.
I am trying to find out the best way to do a mass edit for the "Managed by" values of our security and distribution groups.
I know we can export the "managed by" field by csvde but I am not sure this is the correct way to do it. Also in the case that there are multiple users assigned to be managing a distribution group it only shows one value. Also powershell from Exchange
2010 can be used with "get-distribution" but as our AD environment is 2003 is this correct also?
Finally once the data is exported to csv can it be edited to then reimport and udpate the existing group managed by fields with new values?
Not really sure that the best way to go about this is.
Summary - We have 2003 AD with Exchange 2010 and I am trying to export a list of all our Distribution/Security groups showing the group name and managedby values so we can edit and update the
existing managedby values with new ones. In some cases we have multiple users as the owners.
Appreciate any advice on how this can be best achieved. Thank you.

Hi,
We can use the following command in Exchange 2010 to export "Managed by" field of Distribution and Security groups:
Get-DistributionGroup | Select-object Name,@{label="ManagedBy";expression={[string]::join(“;”,$_.managedby)}},Primarysmtpaddress | Export-Csv
C:\export.csv
After you changed the Managed by field in export.csv and saved it as a new file named import.csv, we can run the following command to set with new value:
Import-Csv C:\import.csv | Foreach-Object{ Set-DistributionGroup –Identity $_.Name –ManagedBy $_.ManagedBy}
Hope it works.
Thanks,
Winnie Liang
TechNet Community Support

2010 error on T43 with new HD

Similar Messages

Maybe you are looking for