236,,No connection to gateway ???
Hello Experts,
We are getting following error in one of our production system very frequently in sysstem logsSM21
"Communication error, CPIC return code 020, SAP return code 236"
Error says "236,,No connection to gateway"
Could you please suggest what may be the reason for getting this error ?
What needs to be cheked from Basis side.
Thanks
Regards,
Amber S
Hi Amber,
Could you please suggest what may be the reason for getting this error ?
The errors you encounter indicate that the problem lies in the
underlying network layer. This error is network error or due to the load on the server refusing the connect from the server. Connection to gateway could not be established. Normally this is because a RFCs resource lack or connect
time-out.
What needs to be cheked from Basis side?
1.increase the parameter rdisp/max_gateways to 200.
2.Also check if your /etc/services files have the correct entries.
3. Set the below parameters if your release is below 700.
gw/cpic_timeout = 1800
gw/gw_disconnect = 0
4. And also check the notes..590929, 559119, 34116
Hope it resolves your issue.
Thanks
Kishore
Similar Messages
-
HT204388 can you connect a GATEWAY TOWER to a MAC 23in CINEMA MONITOR?
can you connect a GATEWAY TOWER to a MAC 23in CINEMA DISPLAY?
Hi, likely you can, but which 23" is it, one requires an expensive DVI-> ADC connector, not the cheaper ADC->DVI connector, the later one has DVI already.
Then it depends what output your Gateway has for Video.
ADC...
http://km.support.apple.com/library/APPLE/APPLECARE_ALLGEOS/TS2085/58846_1.gif
VGA & DVI...
http://cdn.overclock.net/2/21/215b66d1_all-DVI-types.jpeg
http://www.mytechsecrets.com/wp-content/uploads/2011/01/dual-monitor-video-card. jpg -
Social Cannot connect to gateway error
I know that alot of people are having this issue as well as I. but i just have a bit of info that might help sovle it.
I noticed that this error only started occuring with the new version of social (1.2) because i have 2 N8's and one of them has V1.1 and it works flawlessly but my other N8 has V1.2 and it always tells me that it cannot connect to gateway.
Hope this helps, and if anyone finds the answer plz let me know thanks!If you have done the following and still can't access Ovi Social, this might be the one for you:
1. Created an Ovi Account
2. Restore and Delete
3. Re-flash your unit with Nokia Center Support
ATTENTION: This issue is a Nokia problem.
"Nokia is putting their free services and paid services on one server."
Currently, https://sm.ovi.messaging.nokia.com/cds is being accessed by Ovi Social which is a free service. Now this URL is identified as 67.220.123.45 and is tagged as one of Nokia's paid services, Nokia Push Mail. One may experience this problem if a) the Telco offers Nokia Push Mail and b) if the subscriber is a prepaid account. In the Philippines, Nokia Push Mail is being offered by Smart and I have a prepaid account so i can't access Ovi Social. I tried using a postpaid SIM and it work perfectly fine. Now I tried it with Globe using a prepaid SIM and it works perfectly fine but i think they don't offer Nokia Push Mail (yet) so that figures. I don't know why Nokia is so quiet about this issue, they should address this problem. This is still a pending issue in Smart-side because Nokia is still not answering.
Solution: Try changing Telco -
Hi
While Configuring Siebel Server we are getting "Unable to Connect to Gateway server" error in siebel 8.2.2.14
Our OS is windows 2008 R2 64 bit,Orcale client is 11g 32 bit and Oracle DB is in 11g.We are also able to connect to DB using ODBCSQL.
Please help.
Regards
ShuvenduHello Shuvendu,
Thanks for using Oracle Communities.
About your error, there could be many reasons, To start with, please have following knowledge article to know possible reasons.
C028: "Unable to Connect to the Siebel Gateway Name Server" Logged By Configuration Wizard (Doc ID 1391312.1)
I hope it helps.
Best Regards,
Chetan
P.S. If any one of the provided responses has been correct or helpful it would be great if you could mark them as appropriate. -
Hi All , Getting connection to Gateway error when synchronizing in MI
Hi All , Getting connection to Gateway error when synchronizing in MI using MAU application .
Please provide the solution ASAP.
Also provide the notes which can be avilable in SERVICE.SAP
Thanks&Regards.
BharatHi,
well, the error - you should get this error as well if you sync with a new and empty client? It seems your Sync service is down. Check the sync service itself. Is the URL accessible from the device itself?
It is usually not related to the App (MAU in your case) it is related to the ladscape itself.
Can you add the correct error message and the part of the trace that shows the message? Including the lines before with the ping if the server is available?
Regards,
Oliver -
C7 Social: Unable to connect to Gateway!!!
Hello All,
When i'm trying to use Social client in C7 getting the message "Unable to connect to Gateway". It was working fine for some days. Any idea why this issue is occurring?? How to overcome from this??
Thanks,
Abhilash.Hi,
Please clarify me the following.
You specified the login name as 'SADMIN'. Is this the login id, that you used for your Operating System? "Entered name account authentication gateway server name" expects you to enter the NT login, not the DB login.
You may also expected to specify your network name, if your login id is specific to a network. e.g Oracle\Rajkumar assuming that Oracle is your network and Rajkumar is the user name.
You may not expected to have the DSN created, as Gateway may not be interested in knowing which DB you are connected to. And you neither enter the 'DB name' anywhere in the 'Gateway Server Configuration', if my understanding is right.
Please confirm.
Below pages are for reference (not directly relevant to your question):
http://docs.oracle.com/cd/B40099_02/books/SiebInstWIN/SiebInstCOM_Prep18.html
Bookshelf v8.0: Requirements for Siebel Gateway Name Server Installation and Configuration
Thanks.
Regards,
Rajkumar Raju -
Netlet fails: "Unable to connect to Gateway: default:443"
i have installed the portal 3.0 sp4, MAP and HP for sp4.
when using netlet, it tells me: "Unable to connect to Gateway: default:443"
the platform.conf file contains the right gateway name.
why does the netlet uses default:443 instead of the right gateway name and port?
thnx, thomasafter reinstalling the server and the gateway, i face the same problem again, but i found out, that the error only occurs when the anonymous desktop is enabled.
logging in using ldap authentication, everything works; but logging in, using the anonymous desktop, and then loging in at the login-chanel using ldap-authentication, the error occurs, when using Netlet.
looking at the install logs, i found out that the sp4 wasn't able to update the "iwtGateway-netletproxy-port" and the "iwtNaming-sessionURL" attributes;
could one of this be respobsible for the failure ?
has anyone an idea, how to solve the problem ?
thnx, thomas -
Netlet - unable to connect to gateway
Issue with Netlet.
Trying to define the following rule so non-browser application can do
http requests over secure tunnel:
WebTest|null|false|30011|<host>|80
(where <host> is the relevant webserver)
Getting the following error:
Unable to connect to Gateway: default:443
Any assistance greatly appreciated.It seems that this problem is stemming from the variable "WT.gateway"
(stored in the com.iplanet.portalserver.session.Session object) being set
to "default". This causes the applet parameters of the Netlet to be
incorrect. The "remoteHost_x" parameter is being taken literally and the
Netlet is trying to connect to default:443.
In my example, the applet tag looks as follows:
<html>
<head>
<HEAD><TITLE>Netlet</TITLE></HEAD>
<script language=javascript>
var needToSleep = true;
</script>
</head>
<BODY TEXT="#000000" BGCOLOR="#FFFFFF">
<p><applet
codebase="https://algol.solnet.com.au:443/http://algol.solnet.com.au:8080/netlet"
archive="ips_netlet.jar" code="SServer.class" width=1 height=1 MAYSCRIPT>
<param name="cabbase" value="ips_netlet.cab">
<param name="configURL"
value="https://algol.solnet.com.au:443/http://algol.solnet.com.au:8080/NetletConfig">
<param name="resourcesURL" value="/NetletConfig?func=loadResources">
<param name=listenPort_0 value=8000>
<param name=remoteHost_0 value=default>
<param name=remotePort_0 value=443>
<param name=serverPort_0 value=8080>
<param name=serverHost_0 value=algol.solnet.com.au>
<param name=listenPort_1 value=30011>
<param name=remoteHost_1 value=default>
<param name=remotePort_1 value=443>
<param name=serverPort_1 value=80>
<param name=serverHost_1 value=david.mel.solnet.com.au>
<param name=sessionID
value=43345sdafxcspdbliqvfxipuglbqoqr14sp5r6@[email protected]@8080@/UbyqraGrfg>
<param name=numParms value=2>
<param name=doPortWarning value=true>
<param name=netletKeepAliveInterval value=0>
</applet>
</body>
</html>
David Broeren wrote:
Issue with Netlet.
Trying to define the following rule so non-browser application can do
http requests over secure tunnel:
WebTest|null|false|30011|<host>|80
(where <host> is the relevant webserver)
Getting the following error:
Unable to connect to Gateway: default:443
Any assistance greatly appreciated. -
SharePoint 2013 and SAP connectivity / SAP Gateway for Microsoft and Duet Enterprise 2.0
Hello,
we are investigating the connection possibilities of SharePoint 2013 with SAP.
The basic scenario in our cases involves the transfer of documents and/or metadata from SharePoint to SAP possibly through a Workflow in SharePoint.
From my research the most promising official (no 3d-party) interfaces that can be used are the Duet Enterprise 2.0 and the SAP Gateway for Microsoft.
From my understanding both interfaces allow only the consumption of Data from SAP to SharePoint and not vice versa. Moreover the interoperability of documents seems not be supported. Are CRUD operations from a SharePoint native lists to SAP supported?
Can someone please clarify this topics?
I have found lots of documentation concerning the interfaces but not a clear answer to this questions.
Many thanks in advance!
IoannisHi Ioannis,
It seems that there is no built in method to get data from SharePoint list in SAP.
As a workaround, we can export SharePoint list to excel and then use that spread sheet as a source data in SAP.
http://scn.sap.com/thread/3467263
http://scn.sap.com/thread/3472110
As this issue is regarding to SAP, I recommend you to ask the question in the SAP:
http://scn.sap.com/welcome.
More experts will assist you, then you will get more information relation to SAP.
Thanks,
Victoria
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Victoria Xia
TechNet Community Support -
Trouble connecting older Gateway desktop to home network
Hi all-
I am trying to connect an older Gateway 5200s desktop (that we have used for internet previously) to my current home network, but I'm not getting any internet connectivity.
Home router is Actiontec M1424 wr rev E.
the old Gateway uses Windows XP Prof v 2002 SP3
The wireless network adapter is 1394 Net Adapter and also the Intel R pro/100 VE network connection
(the Intel adapter says a "network cable is unplugged" and I never knew what that meant- connections have worked in the past)
My current home system is a Dell desktop running Windows Vista home
The old Gateway is up and running, but I just cant seem to figure out what the internet connection problem is.
Any thoughts?
Thanks
Solved!
Go to Solution.FJT109 wrote:
Hi all-
I am trying to connect an older Gateway 5200s desktop (that we have used for internet previously) to my current home network, but I'm not getting any internet connectivity.
Home router is Actiontec M1424 wr rev E.
the old Gateway uses Windows XP Prof v 2002 SP3
The wireless network adapter is 1394 Net Adapter and also the Intel R pro/100 VE network connection
(the Intel adapter says a "network cable is unplugged" and I never knew what that meant- connections have worked in the past)
My current home system is a Dell desktop running Windows Vista home
The old Gateway is up and running, but I just cant seem to figure out what the internet connection problem is.
Any thoughts?
Thanks
Did you connect wirelessly before with this machine? Whose wireless adapter is the 1394 network adapter? - typically that means a firewire adapter that is not wireless. -
Can't get wireless connection to Gateway laptop
My wife has a school-district issued Gateway laptop- state of the art. We can't get connected to the internet at home using our new airport express. The imac gets on fine, and the gateway gets on if we simply plug the modem into the computer, but nothing wirelessly. It's works for her at her job, it works in coffee shops. Her tech person told her it's equiped to work at home with adding any software, but we get nothing. Something we're supposed to tweak?
My wife has a school-district issued Gateway laptop- state of the art. We can't get connected to the internet at home using our new airport express. The imac gets on fine, and the gateway gets on if we simply plug the modem into the computer, but nothing wirelessly. It's works for her at her job, it works in coffee shops. Her tech person told her it's equiped to work at home with adding any software, but we get nothing. Something we're supposed to tweak?
-
Dear Guru's
We have imported portal content in our PRD portal, however when we try to reach some ESS services the following error message appaers, help needed
Connect to SAP gateway failed Connect_PM TYPE=A ASHOST=nldbpd00 SYSNR=01 GWHOST=nldbpd00 GWSERV=sapgw01 PCS=1 LOCATION CPIC (TCP/IP) on local host with Unicode ERROR partner 'nldbpd00:sapgw01' not reached TIME Fri Jul 31 14:34:57 2009 RELEASE 700 COMPONENT NI (network interface) VERSION 38 RC -10 MODULE nixxi.cpp LINE 2823 DETAIL NiPConnect2 SYSTEM CALL connect ERRNO 10060 ERRNO TEXT WSAETIMEDOUT: Connection timed out COUNTER 2
I allready set the JCO Pool numbers to 100 etc.
Variable CPIC_MAX_CONV is set in Windows.
Has this something to do with RFC-connections? Or do we need to open a port?
Looking closer at the service it calls sapgateway sapgw01 wich is the gateway of our acceptance system, the service should call gateway sapgw00 wich is the gateway of our PRD system. How can we fix this ?
Edited by: Stephan Luijbregts on Jul 31, 2009 5:18 PM
Edited by: Stephan Luijbregts on Jul 31, 2009 5:20 PMHi,
There is some problem with the Jco connection. If you go to JcO maintenence and test the connectivity of each data/metadata (in webdynpro page of Content admin)you will know which connection has the problem. The causes might be
1. Service not included in services file of the server
2. Wrong parameter
3. Something wrong in SLD
Regards
Srini
Edited by: Sinivasan Rajamani on Aug 1, 2009 8:30 PM -
Unable to connect siebel gateway name server during configuration enterprise server
Hi,
when I try to configure Siebel enterpise after entering the port of the gateway server name I get the following error: "Unable to connect gateway server name".
I perform the following steps:
1) Configuration Gateway Server Name
Entered port TCP/IP = 2320
Enable automaticaly start server gateway name server
Show pop up "Configuration siebel succesful"
2) Configuration Enterprise Server
Entered name account authentication gateway server name = SADMIN
Entered passoword account authentication gateway server name = SADMIN
Entered name host gateway server name = VDIMTNSIEBEL01 (name my machine)
Entered port TCP/IP gateway server name = 2320
show pop up error : "Unable to connect gatawey server name"
I can not find the log file in order to understand the issue.
When I try to connect to the gateway from the browser with the url
vdimtnsiebel01:2320 I get this screen mode:
???@??????? ?????????? ????????QÈ ??? ??????????? ??? ??? ? ?h????
and writes this log in the file "C:\siebel\8.1.1.0.0\ses\gtwysrvr\log\NameSrvr.log
SisnapiLayerLog Error 1 0000001151c810a0:0 2013-06-25 10:11:27 4980: [SISNAPI]: Rx msg len=0 peer=VDIMTNSIEBEL01.ISCVDI.LOCAL avail=325 Hello expected session=13
474554202F66617669636F6E2E69636F
20485454502F312E310D0A486F73743A
207664696D746E73696562656C30313A
323332300D0A557365722D4167656E74
3A204D6F7A696C6C612F352E30202857
696E646F7773204E5420362E313B2057
4F5736343B2072763A32312E30292047
65636B6F2F3230313030313031204669Hi,
Please clarify me the following.
You specified the login name as 'SADMIN'. Is this the login id, that you used for your Operating System? "Entered name account authentication gateway server name" expects you to enter the NT login, not the DB login.
You may also expected to specify your network name, if your login id is specific to a network. e.g Oracle\Rajkumar assuming that Oracle is your network and Rajkumar is the user name.
You may not expected to have the DSN created, as Gateway may not be interested in knowing which DB you are connected to. And you neither enter the 'DB name' anywhere in the 'Gateway Server Configuration', if my understanding is right.
Please confirm.
Below pages are for reference (not directly relevant to your question):
http://docs.oracle.com/cd/B40099_02/books/SiebInstWIN/SiebInstCOM_Prep18.html
Bookshelf v8.0: Requirements for Siebel Gateway Name Server Installation and Configuration
Thanks.
Regards,
Rajkumar Raju -
Siebel 8.1.1 on linux - server fails to connect to gateway after stop/start
I have a very stubborn symptom in my environment, with Siebel SIA 8.1.1 [21111] on OEL 5 2.6.18.
Everything will be working fine after initial install, then I stop the Siebel Server and Gateway, start the services again and the Siebel Server fails to start. The NameServer.log complains that the server cannot connect to the gateway configuration store, and that the login password is incorrect. However it was just working minutes prior. Once it fails like that I can fiddle with it all day and still the Siebel Server will not start.
I have tried a number of suggestions found, verifying the odbcsql command works, verifying the memory files *.shm is not still in the admin directory, making sure all approp. processes are closed after stopping the siebel server, recreating the gateway and siebel server services, rebooting the vm.
The symptom and log messages never change. Once in a while for no apparent reason the siebel server will start again but sure enough if I stop it, it won't come back up.
I have a couple of environments that I have worked with and tried things but both experience the same symptom.Good one. For reference its detailed in
[Siebel CRM 8.1.1 DataDirect License file IVSE.LIC is missing from Gateway Name Server (Doc ID 751784.1)|https://metalink3.oracle.com/od/faces/secure/km/DocumentDisplay.jspx?id=751784.1&h=Y] -
Connect to Gateway Failed during database instance installation
Hi All,
I install Netweaver 2004 (6.4) ABAP stack.
I've finished the installation of oracle 10.2 and central instance. During the installation of database instance, an error happens when "starting RFC jobs".
In the logviewer:
ERROR 2007-07-02 18:37:14
FRF-00007 Unable to open RFC connection.
ERROR 2007-07-02 18:37:14
FRF-00063 RFC logon failed with message: Failed: SAP_CMINIT3 : rc=20 > Connect to SAP gateway failedConnect_PM GWHOST=MYHOSTNAME, GWSERV=sapgw00, SYSNR=00
In \program files\sapinst_instdir\<SID>\SYSTEM\ABAP\ORA\UC\DB\dev_rfc.trc:
ERROR file opened at 20070702 183713 China Standard, SAP-REL 700,0,102 RFC-VER 3 896205 MT-SL
T:744 Error in program 'sapinst': ======> SAP_CMINIT3 : rc=20 > Connect to SAP gateway failed
Connect_PM GWHOST=<b>MYHOSTNAME(>8 characters)</b>, GWSERV=sapgw00, SYSNR=00
LOCATION CPIC (TCP/IP) on local host
ERROR partner '10.10.10.10:3300' not reached
TIME Mon Jul 02 18:37:13 2007
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -10
MODULE nixxi.cpp
LINE 2770
DETAIL NiPConnect2
SYSTEM CALL connect
ERRNO 10061
ERRNO TEXT WSAECONNREFUSED: Connection refused
COUNTER 1
>TS> Mon Jul 02 18:37:14 2007
T:744 Error in program 'sapinst': ======> SAP_CMINIT3 : rc=20 > Connect to SAP gateway failed
Connect_PM GWHOST=MYHOSTNAME GWSERV=sapgw00, SYSNR=00
LOCATION CPIC (TCP/IP) on local host
ERROR partner '10.10.10.10:3300' not reached
TIME Mon Jul 02 18:37:14 2007
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -10
MODULE nixxi.cpp
LINE 2770
DETAIL NiPConnect2
SYSTEM CALL connect
ERRNO 10061
ERRNO TEXT WSAECONNREFUSED: Connection refused
COUNTER 2
In \usr\sap\<SID>\DVEBMGS00\work\dev_rfc.trc:
errors like this:
>TS> Mon Jul 02 18:38:05 2007
T:2284 Error in program 'igsmux': ======> Connect to SAP gateway failed
Connect_PM TPNAME=IGS.NW4, GWHOST=MYHOSTNAME, GWSERV=3300
ERROR partner '10.10.10.10:3300' not reached
TIME Mon Jul 02 18:38:05 2007
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -10
MODULE nixxi.cpp
LINE 2770
DETAIL NiPConnect2
SYSTEM CALL connect
ERRNO 10061
ERRNO TEXT WSAECONNREFUSED: Connection refused
COUNTER 52
About my installation environment:
Windows XP
I've enlarged the page file size before installation.
I've looked up the info from Internet, so I've checked the following:
Under \system32\driver\etc\hosts
10.10.10.10 <domainname> <hostname> is configued as a loopback address (I was prompted to use loopback adapter when installing Oracle, because my network adapter uses DHCP)
Under \system32\driver\etc\services
sapgw00 3300/tcp # SAP System Gateway Central Instance Port
sapgw00s 4800/tcp # SAP System Gateway Security Port
I can ping 10.10.10.10 (get response)
(Any possibility that the installation user can not access 10.10.10.10:3300 ??, I don't know.)
However, I can't logged on the system, because in the MMC, "disp+work.exe" turns yellow(Dialog Queue standstill) and then becomes gray.
Some experts in some forums have commented that a long hostname (>8 characters) might be the problem. Is it true?
(I've not installed the standalone gateway instance yet. ) When do I need to install the gateway instance? Now, I installed as follows: DB software->Central Instance->DB instance.
Thanks in advance.
DennisHi,
I had a similar error, when installing SAP BW 3.1. on windows 2000 advanced server, oracle 9.2.0.6.
FRF-00007 Unable to open RFC connection.
ERROR 2006-12-04 07:03:21
FRF-00063 RFC logon failed with message: Failed
However this holds good for NW 2004 also.
To resolve this error you will need to upgrade your SAP kernel level.
1) Download the kernel. i.e. sapdbexe.sar and sapexe.sar.
2) uncar the files sapdbexe.sar and sapexe.sar using the sapcar.exe
On dos prompt go to the particular directory where u have downloaded the above sar files using "cd" command.
3) To Uncar the files use this command on dos prompt
SAPCAR -xvf <your-SAR-file> to uncar the files.
4) shut down sap using the MMC.
then in windows services.msc stop saposcol ,stop oracle service sapserviceSID and and the sapSID_##
5) Now just copy the new kernel files you have uncared above into the /usr/sap/SID/exe/run/ directory of your system
6) Start the services you stopped and start SAP using the MMC.
Now you should be able to logon. Sometimes the MMC shows the yellow status due to missing workprocess status. However the system should work fine.
Manmath Manjunath
Maybe you are looking for
-
System Level Acknowledgement in File to IDOC Scenario
Hi All, I have the File-> IDOC Scenario. Once the IDOC is successfully sent to R/3, PI should send a acknowlement file back to the sender system. Could someone suggest how to design this scenario? Should I use IDOC Acknowledgement. As it is a existi
-
Is there a way to un-minimize multiple windows in an app simultaneously?
If I have multiple windows minimized in an application, it is tedious to have to click on each one to un-minimize them. Is there a short cut to un-minimize many files in one move? I'm in Snow Leopard. Thanks.
-
Netweaver 7.01 ABAP trial version is missing full BW7 functionality?
Hi, I have successfuly installed 7.01 ABAP on my Vista laptop. But I noticed it is missing the BW7 frontend functionality such as Bex Web Analyser, Report Designer, etc. These are all Java based. So i must be missing the java stack as well as the fro
-
Where do iMovies go when you sync to your phone??
Hello. I recently made my first video on my Mac using iMovie '09. I imported to iTunes and it shows under 'movies' in my iTunes. I then selected to sync all movies to my iPhone 4s. It seems to have worked according to iTunes. However, I cannot f
-
Should i get a 3rd gen i pod touch?
is there going to be a 4th gen ipod anytime soon or should i get a 32gb for $225?