24" iMac and slightly shaking display

Hello all,
The display for my new 24 inch iMac (I've barely used it since purchase) seems to be slightly shaky from the neck. Let me elaborate:
While I was typing, I noticed, through a shaking reflection of a lamp from my iMac's glossy screen, that my display is a little wobbly. It's rather slight, but I can see a little vibration from the reflection. I can't notice any vibration on the actual display while typing, however.
Just to test how secure the screen is on the neck, I gently pushed the screen and noticed it wobble a little. When I lower the tilt of the monitor, it wobbles a little after the movement as well. The monitor actually seems rather secure on the neck -- no involuntary movement from a loose neck as far as I can tell.
Is this just the way the iMac is built, and am I just being overly fussy, or is something wrong? As mentioned, I've barely used the machine, so don't think the neck and monitor connection got loose. Also, the iMac is on a sturdy table, so the vibration isn't from that.
Any feedback would be appreciated.

Hi,
according to this http://developer.apple.com/documentation/Hardware/Conceptual/HWTechVideo/index.html#//appleref/doc/uid/TP40003504
you should have no problems (you must scroll a bit down the iMac 24" section)
Have Fun
Stefan

Similar Messages

3 Monitors with 1 iMac and 2 Cinema Displays conected to Windows Gaming PC Help!

Hi
I want to set up a 3 monitor gaming set up with 1 iMac in the middle and 2 cinema displays either side. This would be a tripple monitor set up.
I am looking to set up a new computer and i want to have 3 monitors. I also want to have an iMac so i want the iMac in the middle and two cinima displays next to each other. i Want to also conect these monitors with a Windows 7 gaming PC.
I want to hook up my very powerfull windows 7 gaming computer wich has 3 SLI GTX 560 EVGA cards. These cards have a display port output.
So i want to run 3 monitors from my gaming machine and i also want to have my iMac use the 3 monitors aswell. I also want to take advantage of the full, maximum resolution. I would get the thunderbolt cinema display monitors.
Gaming comupter has 3 display ports so i need to connect each graphics card to one of the monitors. I then need to conect the two cinema displays to the middle iMac.
I have not bought anything yet i just need to know if i can do this. Need to know stuff like what adapers to buy and what compatabilties.
I need to know if this is posible and how i would do it.
Thanks

Could i use some of these cables?
It says they are thunderbolt conpatable.
http://www.macfixit.com.au/shop/index.php?_a=viewCat&catId=229
http://www.macfixit.com.au/shop/index.php?_a=viewProd&productId=2444

27" iMac and two external displays -- using both TB ports best?

Greetings to all.
Currently I have a 2011 Mac Mini to which is connected a 30" Dell display via a Dual Link DVI adapter, and another Dell 21" display via HDMI. I'm planning on getting the 27" iMac and want to check the best way to connect these two displays. While the 30" will still use the Dual Link DVI adapter, should I connect the 21" display via the iMac's second TB port, or via HDMI?

Welcome to the Apple Support Communities
The iMac hasn't got a HDMI port, so you will have to connect your second monitor to your Thunderbolt port, using a Mini DisplayPort to HDMI adapter in order to be able to connect it to the computer

24" iMac and 20" Cinema display extended desktop mode ?

I got a 24" iMac and a 20" Cinema display. I wanted to know if they will work on extended desktop mode? I didnt try to hook it up yet as I am waiting for mini dvi to dvi adapter to come.
Thanks

Hi,
according to this http://developer.apple.com/documentation/Hardware/Conceptual/HWTechVideo/index.html#//appleref/doc/uid/TP40003504
you should have no problems (you must scroll a bit down the iMac 24" section)
Have Fun
Stefan

IMac and 24" Cinema Display Brightness Issue.

Hello all, I'm using a 27" iMac and a 24" cinema display for a second monitor. Every time I restart the computer, my secondary monitor goes to full brightness. Why wont this stick? Thanks!

Hi,
according to this http://developer.apple.com/documentation/Hardware/Conceptual/HWTechVideo/index.html#//appleref/doc/uid/TP40003504
you should have no problems (you must scroll a bit down the iMac 24" section)
Have Fun
Stefan

IMac and new Thunderbolt displays

Has anyone seen anything on the max number of monitors with the 2011 iMac and the new Thunderbolt displays? Theoretically you could hook up 4 external monitors using the new Thunderbolt monitor + the 27' iMac display for a total of 5, 27' monitors. The Thunderbolt monitor was just announced and hasn't been released yet so maybe an Apple insider can answer the question.

Yes. See question 14
<http://support.apple.com/kb/HT5219>

Can I hook up an early 2011 macbook pro to a new iMac AND another thunderbolt display?

I want to get a new iMac, and I have an early 2011 macbook pro. Can I use a two-way thunderbolt cable to hook these two up? If so, will I still be able to use full functionality on both as I move windows to and from one of them? (Like, I use my macbook track pad to move a safari window over to my iMac, and then I can either use my iMac mouse or my macbook's trackpad to do things with that safari window.
ALSO, is it possible to hook up an additional thunderbolt display to all of this? Basically my end-goal is to have a macbook pro hooked up to an iMac with an additional thunderbolt display, that's my "dream set-up" which will make a lot of stuff that I do a lot easeir and less crowded on one moniter.

no the thunderbold display thing would let you use the imac as a monitor for the macbook apart from acting the role of display the imac would be dorment so a very pricy monitor

IMac and 24' LEd Display

Hi,
I'm sure this is really obvious but I have ordered a new iMac + LED display; will I get the cables I need to connect or will that be an additional purchase? The only cables for the Mini DisplayPort seem to be adapters and I can't see the likely connectors mentioned 'in the box'.
thanks.

This is a really nice setup from what I can tell. I wouldn't know for sure because my wife hasn't left the computer since we installed ours. She has had "network" problems at work and came home to work from home.
We put the LED display on a VESA arm to rais it an allow it to be rotated to portrait as well. Nice setup if you do photography or video stuff.
Cheers.

The 27 inch iMac and the thunderbolt display how many hertz

i want to play 3d games so i ask this question.

Please navigate on this page to Support - Tech Specs - then find the model you're interested in. That is where you will find specifications for each model.
You also need to be more specific when asking a question, 27' iMacs come in a variety of configurations with different GPUs and CPUs, RAM etc so you need to specify which iMac, which GPU and which CPU you're most interested in. Also you need to state in which OS you plan to run the games OS X or MS Windows. If you plan to run Windows then you need to specifiy how you will be loading Windows Boot Camp or virtualization.
In other words there are many factors to take into account.
You can also look at the variety of benchmark sites that test that kind of thing. Use Google to find them.

I want to daisy chain my 15 inch mid 2012 non retina macbook pro to a 2012 27inch imac and then to a 27 inch thunderbolt display

I have a mid 2012 non retina 15inch macbook pro, and a 27inch 2012 imac, and a 27inch thunderbolt dsplay and I want to use the imac and the thunderbolt display as dual monitors for my macbook pro and daisy chain them together. I have an extra thunderbolt cable, How would I go about doing this, every time I try to connect it via Target Display mode it only shows up on the imac and the thunderbolt diplay shows the imac screen but I cannot access anything on it. I would love some help, I am probably just missing something simple.

Yes there is on Mac computers that do not come from the factory with "Built In", Note the Words Built In, DVD drive.
On all Mac computers that come with Built In DVD drive Apple has Restricted the installation of Windows from ONLY That Built In drive and Only when it is Physically installed inside the system.
Many people have tried what you want to do and to my knowledge None have been successful.
It is something that is Hard Wired, Written, into the Firmware of these Mac computers.
Some have tried installing Windows on the standard HDD and then moving that HDD to the optical bay or leaving it in the main bay and installing a SSD into either the main drive bay or optical bay and have been greeted with the system not booting to either OS or not booting to Windows.
Something about how boot camp sets up the drive and possibly makes changes to the Firmware or EFI partition on the drive that Windows is installed to or to both that restrict it. You can't even make another Mac OS X partition on that drive without screwing up the Windows install.
To your last post the Answer is NO as stated above.

IMac with 24" Cinema Display

Yesterday I went to the Apple Store and asked about buying a new 27" iMac and connecting it to my 24" Cinema Display. I was told that I could do that with an adapter and was sold a Mini DisplayPort to DVI Adapter.
When I got home I realized that wasn't the correct adapter. I called the store and was told that it wasn't possible to connect the iMac to that particular monitor. (As an aside, I was really ****** because that was the whole reason for making this purchase!)
Then I realized that the video plug fit in the iMac video port. I plugged it in and it seems to be working just fine. I just don't have the power and USB plugs from the monitor cable plugged in.
So, am I okay doing this? Am I hurting anything? Was the genius at the Apple store wrong when I was told I couldn't connect the iMac and the Cinema display? The reason for my concern, several years ago I plugged an external display into an older iMac and it caused video problems requiring the replacement of the monitor.
I can't seem to easily find anything in the forums, so any response/reassurance would be much appreciated!!

OK, you confused me talking about the m-DP to DVI adapter. The Apple Store should refund your money for that bad recommendation. I think whomever sold it to you made the same mistake that I did. They thought that you had the model Cinema Display prior to the one that your have.
So you have the 24" Cinema Display that was available from 2008 until just this past summer. It has one cable that ends in three connectors; mag-safe, USB and m-DP. Well the mag-safe connector was to power a MacBook so that one is fine not plugged in. The USB connector is for connecting the USB ports on the back of the display to your Mac, so there should be no issues plugging that in because it will give you an extra self-power hub if you need more USB ports at some point. And of course the m-DP is allowing the Mac to drive the display.
I think that you should still be OK. Your iMac has a better GPU than the minimum requirement for your display.

I have a Thunderbolt iMac 27" with a Thunderbolt Display attached. I would like to use the iMac and Thunderbolt display in Target Display Mode for my new Thunderbolt MacBook Pro. So far, it seems I can only use the iMac screen itself. How do I do this?

When I press the Command + F2, the iMac screen becomes a secondary for the MacBook Pro, and the Thunderbolt Display becomes the primary screen for the iMac. I was hoping that both screens would become secondaries for the MacBook Pro. Does anyone know how I should proceed? I have tried to connect the Thunderbolt display directly to the MacBook Pro, and the iMac to the Thunderbolt Display via the separate Thunderbolt cable, but there was no difference. And since the MacBook Pro only has the one Thunderbolt port, I'm not sure how to proceed.

Yes, eww, the language definitely states two thunderbolt displays, but I can understand the confusion and was siding with how they could make the mistake to think it would work like they want it to. My appologies for not being clear on that point, but I think you make it clear that the language in the ad says nothing about an imac.
Having said that all the language about TB would suggest that this would be possible. http://www.apple.com/thunderbolt/
High performance on display.
Thunderbolt I/O technology provides native support for the Apple Thunderbolt Display and Mini DisplayPort displays. It also supports DisplayPort, DVI, HDMI, and VGA displays through the use of existing adapters. So you can connect your Apple LED Cinema Display or other display, along with multiple high-speed devices, all from a single port.

Just purchased a new iMac and transferred all info from my old iMac. Now when using iPhoto slideshow is displays the pictures in reverse order.

Just purchased a new iMac and after transferring all info from my old iMac. Now when using iPhoto slideshow it displays the pictures in reverse order.

There's a bug in iPhoto 9.5.1 and Mavericks that affects slideshows played directly from an album. The slideshow will not play correctly if the photos have been sorted manually. Any other type of sort, date, rating, keyword or title, will play correctly.
If you need that manual sort of pictures for your slideshow create the slideshow in iPhoto's slideshow mode.
OT

Which imacs and apple displays connect to late 2008 aluminum macbook 13 inch for use as external display?

I have a late 2008 13 inch aluminum macbook and want to purchase an iMac computer or apple display to use as an external display for it while I'm at my desk.
I can afford up to $700 for sure, maybe up to $1000 and would like one that has built in camera and audio if possible.
I'd like to know what my options are as it seems not all are compatible.
I'll mostly be doing web browsing and photo editing in Aperture.
Also wondering if it's possible to sync 2 computers so that when you make changes on one it reflects the changes in the other. Like you can with certain apps like Evernote.
Thank you for your help!
Cybrena

Yes he is right, Snow Leopard is your first step. Once you have that you can upgrade directly to Mountain Lion if memory serves me correct. Some people were saying that Lion was a little sluggish with the aluminum MacBook but that Mountain Lion was great. Personally I had Lion on it also and didn't think it ran badly. 10.6 was still with Rosetta (the program that ran power pc apps) but this is dropped on 10.7 and up. Up until just the other day I still had the stock 2 gb of ram. The firmware update happens with Snow Leopard and up so it should come up as a software update. If not, it can be done manually as well. The ram I purchased was 60 bucks for the 8 gb. For Lion and Mountain Lion I have to agree with the above reply, that it would run alot better with at least 4 gb. If you run that many apps at once then you are going to want as much ram as you can get. If you add a solid state drive you will be amazed at the difference it will make too.

Have CS 5 Installed on my iMac and works ok. But installed on my new MacBook Pro it won't open NEF files from my Nikon D810. Displays NEF icons, but when I try and open them the response is: Make sure latest RAW updates are installed. If problem persists

Have CS 5 Installed on my iMac and works ok. But installed on my new MacBook Pro it won't open NEF files from my Nikon D810. Displays NEF icons, but when I try and open them the response is: Make sure latest RAW updates are installed. If problem persists follow link: http://www.adobe.com/go/kb407111. Have installed Bridge 5.0.2.4; Raw Ref Version 7.0.0.308; DNG converter_8_7_1.dmg; Bridge 5.0.2 Update 2. Also same problem with Lightroom which I don't normally use. Lightroom_3_LS11_mac_3_6.dmg installed.

In the link you posted it states that the Nikon 810 requires ACR 8.6 or newer.
Version of ACR are specific to versions of Photoshop. You cannot use 8.6 nor even 7.0.in CS5.
I believe that ACR 6.7 is the latest that will work with CS5, so make sure you have this installed and get rid of ACR 7.
Having 2 versions of ACR will cause problems.
You have already downloaded DNG Converter 8.7.1.
Have you double clicked the DMG file to allow you to install DNG Converter on your computer?
Be aware that DNG converter is a stand-along application and not a plug-in.
You need to open DNG converter at select the FOLDER that contain your .NEF files.
Don't open the folder and try to select individual files, it doesn't work that way.
After converting your D810 files to DNGs you can then open the DNGs in CS5
The problem is your camera didn't exist when CS5 & its version of ACR was developed.
i don't use Lightroom, but the list mentions Lightroom 5.6 as needed to open D819 so your 3.6 version of LR won't cut it.

24" iMac and slightly shaking display

Similar Messages

Maybe you are looking for