24" iMac from 2008 display went grey

A couple days ago I noticed white single pixel height horizontal lines flickering all over my display.  I restarted the computer and it stopped but started again the next day.  Seemingly random flickering continued until suddenly the entire display went grey-ish.  Restarting does not help.  Thanks for any help! 

Sounds exactly like what happened to my 24". The grapphics card is going bad. Most likely it will need to be replaced which can by done DIY for $250-$350. When mine first went bad I was able to use SMC Fan Control to increase the speed of the CPU fan, which would stop the freezing. Over time I needed to gradually increase the speed of the fan to keep using it. It lasted another 3 months or so before the card totally failed.
All 24" iMacs had removable GPUs, so repair is possible without replacing the entire Logic Board. There probably won't be very many choices as to what card you can use. Sometimes the cards pop up on eBay, sometimes they are cheaper elsewhere. Although it uses an industry standard graphics slot, it simply won't work with a graphics card that's not specifically made for your model. When the NVIDIA chip went bad in my 2008 24" I chose to replace it with a cheaper and technically inferior ATI chip, because the same thing could have happened again, and graphics performance is not a big concern of mine. I got it from cwioutlet.com.

Similar Messages

  • Need help speeding up my old iMac from 2008 - defragment?

    I have an old 20 inch iMac from 2008. It is a 2.66 GHz Intel Core 2 Duo with 4 GB of Ram. Its still running Leopard 10.5.8, which is te last version of Leopard (I believe).
    I have several questions, but I will start with the biggest one.
    How can I speed it up? It runs very sluggishly and I've tried just about everything to try to get it to speed up. I've done all the recommended things, such as removing unnecessary startup programs, repairing disk permissions, freeing up hard drive space, monitoring the task manager for processes that take up a lot of CPU power and I've added more ram. The CPU can be at 90% idle and it will still act slow.
    I know its not the software because its as old as the OS, so the system should be able to handle it, for example, I am running Adobe CS3. A friend told me that maybe I need to defragment. I read that after a certain OSX version the system does not need to defrag because the OS prevents the hard drive from fragmenting in the first place. Plus, there is no utility to defrag in the OS. I also read somewhere that if you do happen to fill up your hard drive to the very brim the data will fragment regardless. I did fill the hard drive to the brim -- to about 500 MB of free space. Since then I have freed up about 100 GB, but its slow.
    Should I find a way to defragment? If so, is there any 3rd party software that is recomended for an old system like this?
    I have tons more questions, such as:
    - How to upgrade the OS to Snow Leopard, Lion or Mountain Lion.
    - Should I backup the system via Time Machine before upgrading the OS to Snow Leopard, Lion or Mountain Lion?
    - If I do upgrade my OS will my software be incompatible and do I need the original software discs to reinstall them?
    - Why does my Time Machine take so long to backup?
    I'd like to start with an answer about defragmenting.

    Things You Can Do To Resolve Slow Downs
    If your computer seems to be running slower here are some things you can do:
    Start with a visit to: OS X Maintenance - MacAttorney.
    Boot into Safe Mode then repair your hard drive and permissions:
    Repair the Hard Drive and Permissions Pre-Lion/Mountain Lion
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    Repair the Hard Drive - Lion/Mountain Lion
    Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Restart your computer normally and see if this has helped any. Next do some maintenance:
    Suggestions for OS X Maintenance
    For situations Disk Utility cannot handle the best third-party utility is Disk Warrior;  DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
    OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep.  Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger.  These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
    OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
    I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
    For emergency repairs install the freeware utility Applejack.  If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line.  Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
    When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
    Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
      1. Carbon Copy Cloner
      2. Data Backup
      3. Deja Vu
      4. SuperDuper!
      5. SyncTwoFolders
      6. Synk Pro
      7. Synk Standard
      8. Tri-Backup
    Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
    Additional suggestions will be found in Mac maintenance Quick Assist.
    Referenced software can be found at CNet Downloads or MacUpdate.
    Additional Hints
    Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
    Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
    Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
    Check for applications that may be hogging the CPU:
    Open Activity Monitor in the Utilities folder.  Select All Processes from the Processes dropdown menu.  Click twice on the CPU% column header to display in descending order.  If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar.  Click on the Force Quit button to kill the process.  See if that helps.  Be sure to note the name of the runaway process so you can track down the cause of the problem.
    Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file.

  • I have an iMac from 2008.  When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen.  Now just back and forth blue to light blur

    I have an iMac from 2008.  When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen.  Now just back and forth blue to light blur

    Reinstall OS X:
    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
    Reinstalling Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion: Select Reinstall Lion and click on the Continue button.
    Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

  • Can i use a iMac from 2008 with broken graphic card as extra monitor

    Can i use My Old iMac as a extra monitor.  My Old iMac from early 2008 has a broken graphic card nvidia 8800 gs. When I start it up I hear the bong and see the symbol spinning then the screen goes black from right to left the computer is running but I can't use it. I assume it's the graphic card. Can I use this iMac as an extra monitor to my other iMac.?

    No sorry.

  • Display went grey?

    Hello- I have a early 2008 Mac Pro and just recently the screen started freezing up after restarting the computer twice the screen now goes grey with blue lines running down it. My question is "do in need a new video card? Upon start up I do see the grey apple and it loading but after that nothing but grey screen.
    If someone could assist me with what wrong that would be great!

    The plot thickens. I reverted back to the bios that came with the motherboard, no difference. On a cold start-up the bios does not recognize the presence of the All-in-Wonder pci-e.  I tried another power supply, no difference. Then I stumbled across something really strange. I needed some files that where trapped on the videoless pc. So, I let it boot and used remote desktop to get at the files I needed. Then just for laughs I used shutdown -r from a command prompt to restart the sick pc. The video started right up when it rebooted. After restart the pc ran all day without any video issues. It has been four days now and this behavior is repeatable. I boot the sick pc, the video card is not detected, I remote desktop in, make it do a restart and I have video.  For the life of me I can't imagine what the difference would be between a cold start and a restart. Anybody have any ideas ??

  • IMac (Early 2008 Model) Screen Greys Out And Then Must Reboot

    The iMac that we bought back in the summer of 2008 has been having issues over the past couple days. I was using Safari yesterday and then a grey "box" filled the screen and then told me to shut down the computer (by holding down the power button) and then restart it. I did that and I was back on my way. Then a few other people used the iMac (on their own accounts using Safari and iMovie) and had no problems. Just an hour ago I was exporting a video in iMovie and was using Safari at the same tiime and the screen greyed out again. I restarted it and this time I got 3 beeps with a 5 second pause in between over and over again while the screen was black. I held down the power button and it turned off; I waited a few minutes and turned it back on and now its working again. Any idea what's going on? I upgraded the RAM and upgraded to Lion last month. I have not reset the PRAM yet, I would like to know what the problem is and why this keeps randomly happening to what seems to only be my user account.

    I've looked at that, I did try to link the discussion to the article but it failed too   Thank you though.
    I just created an Ubuntu DVD to run - the graphics are distorted on that too so I'm guessing it's a fault with the graphics card.  I don't have the knowledge to confirm/deny it so a trip to an Apple Store is probably in order?

  • My 24" iMac (2007/2008) display is "going yellow"...what needs replacing?

    Everything else is working fine. There appears to be "wave of yellow" in the display and limited brightness...
    I do a lot of graphics work, and this is distracting...
    How do I get it back to  a nice, clean crisp white display? What needs replacing? Video card?
    Thanks for any help/direction,
    Sunny

    Yes, I tried doing all those normal things.
    If someone was not used to this computer they might not have noticed although it certainly does not "pop"
    I noticed it being dingy as soon as I turned it on and I also have another 24" next to it. There is a big difference.
    I suspect the seller was getting rid of a leon.

  • HT201343 what should I do if I have an Imac from 2008 to use my screenplay in my tv?

    i just bought an apple tv 3 and i would like to use airplay. I saw thats only possible for newest imacs. There is another way to use my imac on my tv and apple tv? thanks

    Try airparrot, an app that does this, I think your İOS is up to date enough.  Check out airparrot.com to see.
    Jules

  • Imac 20 2008 doesn't sleep

    I have a 20 inch iMac from 2008, I upgraded to lion a few months ago, and everything was running fine, but since the software update to 10.7.2 it doesn't go to sleep.
    What should I do?

    Hi...
    Maybe some hints here:
    http://support.apple.com/kb/HT1776
    Generaly, you'l need to be systematic and rule out the varions possible causes, and there are a lot...
    /Dennis

  • My mac book pro 17 inch , 2008 year , display went dark, and the steps in "everthing Mac" book did not work, any ideas?

    my mac book pro 17 inch , 2008 year , display went dark after rebooting from origianl disc, and the steps in "everthing Mac" book did not work, any ideas?

    The router might be bad or incompatible, but let's be optimistic.
    On System Preferences, go to Network/Advanced/PPP. Only two items should be checked: Connect Automatically When Needed and Disconnect when switching user accounts. Uncheck everything else. Now, click Okay on the end of the page. The next time you're online, you shouldn't be disconnected.
    If you still get disconnected like before, we might be dealing with a router issue - which can get rather complicated.

  • Display freezes using Safari 5.1 after Mac OS 10.74 install - iMac (early 2008)

    After installing Mac OS X 10.7.4 on a 24-inch iMac (Early 2008), experiencing display anomalies and freezes, while using Safari and web-based e-mail. 
    Screen will go all white, system will lock up, requiring power-off restart. Latest incident  while using Safari -- display went green with vertical blue stripes, system hang, requiring power-off restart.
    System details:  Intel iMac, 24" (Early 2008), 2.8 GHz Intel Core 2 Duo CPU, 2 GB RAM, Mac OS X 10.7.4.
    Any suggestions on how to resolve these video distortion / system hang problems would be greatly appreciated.

    As old as your iMac is, have you cleaned out the dust? Dust buildup can lead to over heating issues. Remove any and all things plugged into it including the power cord, Remove the RAM access grille. Vacuum all openings starting with the RAM access area (air intake). Vacuum all ports and plugs, DVD slot and the opening across the top of the rear of the body. Blow compressed air through all your openings and vacuum again to remove any dust you loosend. Reinstall the RAM grille. Plug in the keyboard and mouse if not blue tooth. Insert power cord...
    You are now in a perfect position to do a
    SMC RESET
    http://support.apple.com/kb/HT3964
    Shut down the computer.
    Unplug the computer's power cord and ALL peripherals.
    Wait 15 seconds.
    Attach the computers power cable.
    Wait another 5 seconds and press the power button to turn on the computer.
    It is the 5 second timing that initiates the reset.
    Here is a link to a Widget to monitor your temps and other operations:
    http://islayer.com/apps/istatpro/

  • My 2009 iMac gets stuck on the grey Apple logo when booting up.  It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple log

    My late 2009 27" iMac gets stuck on the grey Apple logo when booting up.  It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple logo again.  This could possibly be an HD failure, but then why does Safe Mode still work and the USB install not work?  Any ideas?

    1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
    Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
    2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
    There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
    3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
    Here's a summary of what you need to do, if you choose to proceed:
    ☞ Copy a line of text in this window to the Clipboard.
    ☞ Paste into the window of another application.
    ☞ Wait for the test to run. It usually takes a few minutes.
    ☞ Paste the results, which will have been copied automatically, back into a reply on this page.
    The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
    4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
    5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
    6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
    Triple-click anywhere in the line of text below on this page to select it:
    PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */   /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n   ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' 's/0/Off/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1|head -1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D12 26 48 59 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-  
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    7. Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
    8. If you see an error message in the Terminal window such as "syntax error," enter
    exec bash
    and press return. Then paste the script again.
    9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
    If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
    10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
    [Process completed]
    to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
    11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
    At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
    If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
    12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
    Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
    Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

  • Will my MacBook Pro from 2008 work with the Thunderbolt Display? Or will I need an adapter?

    Will my MacBook Pro from 2008 work with the Thunderbolt Display? Or will I need an adapter? I like to have two monitors and currently using an Cinema Display from 2005. Thanks

    If your computer does not have Thunderbolt you cannot use a Thunderbolt display.  There are no adapters that will help.

  • Have an iMac Early 2008 + Windows 7 and no sound from speaker out? SOLVED!!

    Hello everyone,
    So I'm pleased to say after over a month of trying to solve this annoying problem, it's been solved! Basically, if you have an iMac, Early 2008 edition (8,1) and Windows 7 and notice that the default microsoft driver gives very low sound and the new realtek drivers only give sound through the internal speakers... then this solution is for you!
    What you'll need:
    7-zip (www.7-zip.com)
    Mac OS X 10.5 Leopard Disc 1 (NOT Snow Leopard!)
    Here's what you'll need to do, step by step:
    1) Uninstall the Realtek Driver (latest version currently 2.37) by going to Control Panel / Programs / Uninstall Programs.
    2) Reboot. Upon reboot, the system will automatically reinstall the default Microsoft drivers. You can check this in Device Manager (control panel / system / device manager).
    3) Insert the original Leopard Disc 1 that came with your iMac (very important, as this is the only driver I know for sure will work). Point windows explorer to the folder: D:\Boot Camp\Drivers (assuming d: is your cd-rom drive).
    4) Copy the "RealTekSetup.exe" file somewhere on your desktop. Do NOT install it!
    5) Decompress "RealTekSetup.exe" by right clicking the file and choosing "7-zip decompress". Again, you'll need to make sure you installed 7-zip from 7zip.com prior to doing this.
    6) Go to your Device Manager again, right click the sound device (which should be something like High Definition Audio) and choose "Update Device Software".
    7) Select "Browse my computer for driver software" and direct it to the folder that you extracted the drivers to.
    8) You now have sound through your EXTERNAL SPEAKERS!
    This works because there is a bug that RealTek/Apple does not seem to want to fix where the newer version of the RealTek control panel detects the speaker out as line in and the line in as nothing! This forces drivers normally made for Vista or Vista64 to install on Windows 7, which work 100% great.
    I promise you, if you have an Early 2008 iMac, this WILL fix your problem if you follow each step! Let me know if you have any questions!
    Brad Levicoff

    If you don't have any Leopard disk then just google for "Vista_R199.exe".
    This driver works nice on Early 2008 IMAC. I also tried an earlier version, Vista_R182.exe but there sometimes was a horrible background noise which made listening to music impossible.
    Just download and follow the instructions above in the first post.
    Have fun.
    Uska
    Message was edited by: Uska

  • 2008 Imac us to display recent Macbook Pro?

    I have recent model Macbook Pro and a 2008 iMac Model iMac8,1. It's a 21" model and I know that the 27" inch model can be utilized as an external display for the Macbook. Is there any connectivity available to use my Imac as a display for the Macbook?

    Use a product such as ScreenRecycler over a network.
    (111616)

Maybe you are looking for