24p capture problem

I captured some footage from an XL 2 at 24p using the advanced pulldown. The audio slips out of sync over time when in FCP. It even goes out of sync during playback in the viewer window. However, the footage plays back properly when I open the original Quicktime file off of my Video HD. The problem started when I updated to FCP 5.1.3 but I updated to 5.1.4 and the problem persists.
Has anyone else run into this problem?

I didn't think the XL 2 could do advance pulldown? You may want to check that it is doing what you think it is.
Sounds like your sequence may be set at 29.97 while your clip is running at 23.97.
This article may help your understanding.
http://www.mandarinpictures.com/stephenzinn/

Similar Messages

GY HD11U 24p catpure problem still

Hi,
I read the thread about the capture problems with 25p and I posted my question there as well. When I try to capture my footage, I am getting streaming error messages blaming the tape, or chopped up clips with missing media.
Is the only answer to the problem to use the Apples Intermediate HDV Codec?
I am using final cut 5.1.2 trying to capture from the JVC deck footage in 24p that was shot on the GY-HD110U. I really need to edit what I shot, asap.
Any help? Suggestions?
Thank you all for your time and consideration.
Cheers,
Sharon

Almost forgot to mention... I was looking to gain real-time benefit. I can drop the m2v files on the timeline and RENDER them, but that defeats the purpose of working with the native m2v files...

MIGO-Capturing problem-Item is not available for Excise invoice,deselect th

Hi Gurus
while doing MIGO and part 1 posting am getting following error
MIGO-Capturing problem-Item is not available for Excise invoice,deselect the item
kindly help in this
Maruthi

hi
check all settings in J1ID
or
in po did u got ur all values correctly for excise cess and hcess
if yes then check ur vendor excise details in j1id
if above setting are done properly then check ur CIN setting in spro>log gen>tax on goods movement >india>account determination >specify excise acct as per transaction/specify G/L acct as per transaction
regards
kunal

Capturing Problem with Sony TRV330

Capturing problem with Sony digital8 trv330.
I recently purchased the above camcorder from eBay for capturing old 8mm/Hi8 tapes for editing purpose. The camcorder set to A/V -> DV OUT connected with Firewire to my Power G4 and the Easy Setup was DV-NTSC. The playback on the capture window looks OK except there were no timecode in the Timecode Duration Field and the Current Timecode Field (both shown 00:00:00:00) during playback but there was timedoce in the camcorder viewfinder. When I click the Capture Now button, the capturing window show up with message “waiting for timecode ….”. I have to click “esc” to stop the capturing operation. I trash the Preferences and Ran the Disk Utility without success. I also tried the Easy Setup with DV-NTSC DV Converter as well as DV-NTSC 32Khz, nothing work.
My set up is: Mac Power G4 version 10.5.5/ F.C.E. 4.0.1/ QT7.5.5/ Startup 160 GB-89 GB available/ Scratch 350GB-277GB available. Folks, I need help. Thanks everybody.

Hi, I have a similar problem. I am trying to digitize my 8mm tapes (via firewire) using final cut express (4.0.1). Using easy setup I use DV-NTSC DV Converter and do capture now. I transfer the entire tape but notice the audio is out of synch with the video. This problem gets worse throughout the transfer process. When I use the esc to complete the transfer I get the error " The audio sample rate of one or more of your captured media files does not match the sample rate on your source tape....." So after searching around it is recommended I change the audio sample rate to 32 kHz option. However, when I do this using easy setup and picking DV-NTSC 32kHz I cannot use capture now because I have no timecode and so the window comes up with the message "waiting for timecode". Since there is no timecode this option does not work. Any suggestions? Thanks, Dan

Audio Capture problem in Mac OS X 10.7.5 in Mac mini(in Silverlight)

I got a mac mini and upgrade Mac OS X 10.6.x --> 10.7.5.
However do not hearing the audio in Webpage using Silverlight.(10.6. version doing well)
So, I found the solve this problem, that is a audio capture problem.( My device does not supported Stereo audio data).
this is the source in audio capture using Silverlight code.
CaptureSource source = new CaptureSource()
                        AudioCaptureDevice = CaptureDeviceConfiguration.GetDefaultAudioCaptureDevice()
                    try
                        foreach (AudioFormat af in source.AudioCaptureDevice.SupportedFormats)
                            if (af.Channels == 1 && af.BitsPerSample == 16 && af.SamplesPerSecond == 8000)
                                source.AudioCaptureDevice.DesiredFormat = af;
                                break;
af.Channels is always af.Channel == 2(Stereo)
--- the question is
How can I caputure audio channel mono?
If couldn`t, how can I transfered audio capture data stereo to mono?
Please answer the question as soon as possible ^^

Mavericks is a 5.3 GB file, it takes awhile to download based on the speed of your internet account.

Capture Problems with Vista

While this problem is not specific to PE4, I am hoping someone will be able to help me.
I recently purchaed a Dell XPS desktop for video editing. I am unable to capture from my SONY HDRHC7 camcorder. The new computer runs on Vista Home Premium; my old computer (never had any capture problems before) runs on XP. According to Dell, Adobe, and SONY websites, there are no additional drivers that I need to capture video.
Has anyone had similar problems? And, if so do you have any advice? Thank you.

Hi Butch,
Here is your solution from the Read Me:
Windows Vista Compatibility
Windows Vista is a brand new operating system from Microsoft and has not been available in its final form long enough for Adobe to fully certify Lightroom for use on Vista. Adobe is working hard to finalize support or Vista as quickly as possible and will deliver appropriate software updates over the launch period. Lightroom 1.0 will install and run on Windows Vista but Adobe cannot guarantee the quality of the software experience until final testing is completed. Known issues for using Lightroom 1.0 on the Vista operating system are listed below:
Lightroom CD and DVD burning tools will not currently function
Importing files directly from a Camera or Card Reader may not function properly. Please
copy files to a local hard drive via the operating system before importing the files into
Lightroom
This may not be the answer you wanted but until the next release.........

Cannon GL2 - FCE 2 and iMovie Capture Problems

Hello Hello
I've read here that folks are having a tough time capturing with thier Cannon GL2. The device goes from NO problem to 'Can't intiate a capture because the device looses connectivity.
I tried to find a common denominator to this problem, and it seems this post regarding Quick Time Files can help? Yes?
Is this the main problem?
Anyway I'm also having connectivity issues with both iMovie 6 HD, and FCE 2
Just wondering if I should also follow the directions on this post and have my capture problems solved?
http://docs.info.apple.com/article.html?artnum=301852
BTW - I currently have Quicktime 7.0.4
Thanx

Hi Tom - Thanx for your reply!
Well, yes I have (as my profile indicates), a G5 1.8 Gig, currently with an external Lacie HD plugged in. I also have a Cannon GL2.
But before I go any further, and before I try those directions for cleansing certain Quick Time 7 Library Files, I think I figured out the dilemma.
This problem of GL2 recognition (from what I've read), is common for folks who have similar equipment, and a similar set-up as mine:
It seems (as I've also read here), that my G5 does NOT like 2 devices which require the same connection speed plugged into the 1394 Firewire Port at the same time - trying to share the same bus.
I confirmed this by disconnecting the Lacie FIRST - then booting back up - and WALLAH - the GL2 was certainly receoginzed both in iMovie 6 HD, and FCE 2!
I also further resolved the issue by buying a 'cheaper' Cannon Camcorder - the ZR500.
Now I can actually share the Lacie HD in the Fire Wire Port with this slower connection speed camcorder. And a further benefit is giving my GL2 a rest when it comes to 'capture only'
Does all this make sense?
If so, perhaps I've already discovered stuff that other folks already know ...
Thanx
Mike

Premiere Pro CS5.5 Batch Capture Problems

Hi,
I'm sorry for the repost, but the older questions I can find on this topic won't allow me to reply and they were never answered (last post several months ago).
I'm having the batch capture problem with Premiere Pro CS5.5. Capture with device control works great when single capturing. When I log clips and attempt to batch capture, though, I get the "capture failed: device not found" error in my capture log. I have checked through the FAQ and the complete premiere manual on batch capturing. I've set my device (still using a Canon XL1) and even checked the video size...it matches that of my project (someone on another forum mentioned that this could be an issue). I have had no luck.
Could anyone tell me if this issue has been resolved, or redirect me to a resolution?
Thanks in advance for any help!!
Steve

I have encountered this problem if the current tape position is beyond the last recorded point when you start the batch capture or if any "OUT" points are beyond the last recorded position or if the capture spans any unrecorded portions of the tape. I always thought it was my camera but maybe it is a PPro issue.

ZIU timecode/capture problems

This is issue we've been struggling with for a couple months now, originally thinking that it was an FCP version problem. Now we have been running FCP 5.1.2, Tiger, and QT all at their latest versions still no improvment.
The problem is we shoot a tape with our SONY HDV-Z1U and log the clips in FCP. When we go to batch capture many of about 25% of all these clips have capture problems. Final Cut detects timecode breaks and captures 2,3,4, sometimes 15 versions of these labeling them clip, clip-1, clip-2, etc....
You can actually see these wierd glitches and jumps on the camera LCD and on the FCP capture window. Sometimes the camera will rewind itself over and over trying to find the proper IN on the tape.
It seems like someone out there has had to run across this issue because this is such a common camera and such a common task. I'm almost worried that it's a camera problem and I don't even know where I would go to ask about something like that. I have not been albe to find any documentation that this model camera has TC problems.
Please, help or point me in the right direction it must just add a couple years to my life!!!
Thanks.

I have a ZU1 and I occasionally encounter this problem, but it's usually one clip out of say 25 or 30 on a given tape. I'm never sure what causes the problem and if I simply skip the problem clip I can sometimes go back and digitize just that one last clip.
I do know the ZU1 seems to need plenty of pre-roll in the front of the tape, but I'm assuming that's not the problem. You're using new, high quality tape, correct? Have you tried a simple head cleaning on the ZU1.

Is there going to be a Solution for the Capture Problem?

I've noticed that it is not only me but Final Cut Pro is not capturing video properly, it should not be so hard to capture from my camcorder(PV-DV51), when I hit log and capture the program just quits, after reinstalling, deleting preferences, the Firewire dock is able to see the camera, I can capture with IMovie for crying out loud! so the only question left, is do I have to upgrade Quicktime 7 player to the full version? because I did not find the upgrade in final cut studio package so do I have to purchase separately?
Thanks for the help

"The capture problem" is not, AFAIK, striking any number of folks. At least I've not heard of it. If you're running Final Cut Studio 5, there's not a separate serial - it's a gestalt thingie upon install.
FCP uses QuickTime to do its capturing (iMovie does not). You might try reinstalling QuickTime (don't skip any steps). Go to /Library/Receipts. Trash all QuickTime related .pkg files (Don't worry, you're only deleting receipts so that a full install will take place). Go to http://www.quicktime.com/ and download the latest installer and run it. Reboot.
post back,
Patrick

FX5900XT-VTD128 capture problem

Hi,
I read the many posts about capture problems but did not recognise my issues.
I just got FX5900XT-VTD128 and I am trying to get it to capture with WinDVD creator (bundled). WinDVD would start but then it would hang without listing any capture device.
I installed the latest WDM drivers from the nVidia site (2.20_wdm-vivo.exe)
Device manager list the following devices under sound, video and game controllers:
- nVidia WDM A/V Crossbar (12-2-2003)
- nVidia WDM Video Capture (universal) (12-2-2003)
The multimedia tab in control panel show the following under "devices"
under "Video Capture device" --> -Microsoft WDM Capture
After reading the posts, I suspected a WDM driver problem so I did the following:
1- removed both nVidia WDM devices from device manager
2- removed Microsoft WDM Capture from multimedia devices
3- removed nVidia WDM drivers with Driver Cleaner
I rebooted and confirmed that no nVidia WDM devices were present in Device manager and that no WDM capture device were present under multimedia capture devices.
I re-installed nVidia WDM driver 2.20 and rebooted. Windows plug and play recognised both nVidia WDM devices and installed drivers for it.
When I checked, both Device manager and Multimedia capture device were back as they were before the driver re-install yet WinDVD still hang when I click "capture" (Window is still alive, I can kill WinDVD manualy but I would then not be able to restart it without first rebooting).
I tried Flycap and VirtualVCR with no better result, they hang.
I am using Win98 SE on a Gygabyte GA-7N400-l motherboard with AMD Sempron 2400+ CPU and 512MB RAM. I have no other card in the PC.
I am using nVidia driver 66.94 from the file: "66.94_win9x_english.exe"
Any insight would be greatly appreciated.

also refer to this post....5900 Video Capture
its name is fx900xt capture and got 5 thumbs on the forum title for easy to find....

Newly encountered capture problem

I have a frustrating capture problem that just cropped up in a system that worked close to flawlessly in the past.
Aluminum G4 powerbook, 10.4.11, 1GB
FCE 2.0.3
External hard drive: Mercury Elite Pro FW800 on powerbook FW800 bus
Camera: Canon ZR45 attached via FW400 on a PCMCIA card FW bus
In the past (i.e. about a year ago) this system has worked almost flawlessly (i.e. 1 hour captures from tape, no problem)
In the past few days I have tried to use this system, and everything works fine for 5 minutes (i.e. the camera is recognized, I initiate capture now, it writes a file). Then at 5 minutes, the disk starts making a rhythmic click at about 1/sec and FCE freezes capture. (image frozen on screen). The tape keeps going. If I hit "esc", nothing happens. I get the whirling rainbow of doom, and nothing I can do will allow me to escape. The disk keeps ticking, FCE keeps ignoring the esc. If I attempt force quit and to unmount the disk, I have to keep doing it over and over. FCE even after force quit returns, as does the disk even though in theory, it has been trashed. After a few minutes of continually force quitting FCE and unmounting the disk, things settle down. But none of the captured material is usable ("is not a movie file") in general.
As I said, this is the same configuration of interfaces, disks, computer and camera that I have used without hitch in the past.
Oh, I also used the disk utility to check the disk and it says it doesn't need repair.
This is very frustrating, because it took me about a year of fiddling with different disks and interfaces before I got a system that could reliably capture onto my powerbook, and now it no longer seems to work.
Does anyone have any insights? Many thanks in advance.

Thank you for your response. I checked and it is Mac OS Extended. As far as the actual drive manufacturer, I can't figure this out from anything on the case or in the About this Mac info (posted below). It is about 2 years old, and has not been used that much. I guess it depends on what "that much" means. I transfered 18 hours of DV to it over a month period, and then wrote out 18 disks worth of qt files and dvd files to another drive. When I run "verify disk" it says "passed verification".
FireWire Bus:
Maximum Speed: Up to 800 Mb/sec
OWC Mercury Elite-AL 1:
Manufacturer: Other World Computing
Model: 0x0
GUID: 0x1D20200920366
Maximum Speed: Up to 800 Mb/sec
Connection Speed: Up to 800 Mb/sec
Sub-units:
OWC Mercury Elite-AL 1 Unit:
Unit Software Version: 0x10483
Unit Spec ID: 0x609E
Firmware Revision: 0x102
Product Revision Level: 3.AA
Sub-units:
OWC Mercury Elite-AL 1 SBP-LUN:
Capacity: 465.76 GB
Removable Media: Yes
BSD Name: disk2
OS9 Drivers: Yes
S.M.A.R.T. status: Not Supported
Volumes:
Capture Disk Mercury Elite:
Capacity: 465.64 GB
Available: 105.46 GB
Writable: Yes
File System: HFS+
BSD Name: disk2s10
Mount Point: /Volumes/Capture Disk Mercury Elite

Capture problems to 24p

Hi...
A friend of mine told me he got some problems with Final Cut Pro, trying to
capture in 24p from his JVC GYHD-100U camera to the software.
I would like to know whether a special codec is necessary, or that might be
done using CINEMA TOOL.

intente este Web site
http://www.lumierehd.com/

24F capture problem with CS5

I own a Canon HDV40 camera and I recorded video set at 24F. I chose the 1080/24p preset for my sequence. I now have several .mpeg clips. Each clip is a 60 minute tape.
When I try to move the clips to the timeline CS5 stops responding. Is there an issue with the 24F format and CS5? I do not see a preset specifically for 24F. I also do see any other discussions about 24F and CS5.
Please help I have 18 tapes shot in 24F and i am wondering if i screwed up choosing that format?
John

No, since this was a 3 camera shoot for starters I just captured 3-4 tapes to see how the workflow is going to work. I want to use the multicam feature to edit. I tried creating a new project and imorting the clips but CS5 "stops respoding". I import the, lets say clip1. Move it to the timeline, scrub up and down the timeline no apparent problem.
Then I import clip2, CS5 stops responding. I have used CS5 to capture and edit standard video with no problems. But this 24F footage is creating starnge anomalies. The computer was just built breand-new 4gb ram with a AMD phenom X2 processor TB's of storage.
I think it is related to the 24F format. I'm going to capture something in standard HDV to see what happens when I add it to the timeline.
Any sugesstions?

24p Advanced problems

Hi there. If anyone who can help me with this issue I would greatly appreciate it.
Ok so I am using a Panasonic DVX100a and shot a bunch of footage. I shot it in 24p advanced. I'm using Adobe Premiere CS4 and captured the footage via firewire into a DV 24p sequence. I'm able to edit it fine but am having sever problems with the picture quality. here's what's going on:
1. My first issue is that everywhere I've looked online, everyone says you need to interpret footage and remove 24p pulldown BEFORE you drag clips to the timeline, otherwise it's too late. BUT, I started editing my footage and only after a few hours found out I needed to interpret the footage and remove pulldown. So I did this to the captured footage, and it effected the clips in my timeline, contradictory to what everyone has said about how you must do it before putting clips onto the timeline. Not a big deal, but I'm just wondering why it did this (maybe I have an update other people don't have?)
2. I did a render test to see exactly what removing the 24p pulldown was doing and when I played the rendered clip back on Windows Media Player and VLC, with the 24p pulldown removed I have horrible interlacing, but with it NOT removed I have no interlacing but do have jittery footage. I understand that 24p will be jittery but this looks REALLY jittery. Again, this seems backwards to what I've read about how you need to remove pulldown in order to remove interlacing.
3. With 24p pulldown not removed, I render the file as an MPEG with everything turned up - bitrate and quality. I set the frame rate to 24. When I play it back on VLC it looks decent but not very good. I ultimately want to upload this footage to Youtube so I want it to look nice but I understand it might not look phenominal. Is there a recommended render setting I should use?
I maybe screwed myself by shooting in 24p advanced but instead of blowing it off and just shoting 30i next time I really want to learn the specifics of 24p advanced so I can use it properly in future projects. If anyone knows the answer to these problems, I would be grateful to hear them. Thanks.

I *kinda* solved my problem. Not really. I went through my footage, frame by frame, and when it's interlaced, only the 4th frame is interlaced. the other 3 frames are progressive frames. This is in 24pa. Anyways, when i captured my footage, I captured one long file. I then chopped the long file into small "scenes" to move around the timeline. What''s wierd is that if I interpret footage to my one long, captured file and remove 24p pulldown, ir removes the interlaced frames on some of my scenes and PUTS IN interlaced frames in other scenes. You would think since it's one long, captured file, that by interpretting the footage and removing the 24p pulldown it would effect the all clips evenly. But no, it doesn't. When I don't check the remove pulldown box, then the clips that didn't have interlaced frames now do, and the ones with interlaced frames don't have them anymore. It's wierd - it's like Premiere is automatically removing the pulldown on some parts of my captured video file but not others. Does this make sense? Has anyone else experienced this??

24p capture problem

Similar Messages

Maybe you are looking for