2504 WLC future LAG support?
We just bought a 2504 WLC with 15 AP licenses for our new eight 1141N AP installation. Some confusion about LAG support for these now confirmed by TAC that LAG NOT supported for the time being. Has anyone heard about whether this feature will be added to the 2504 in the future? Seems a waste of those four ports toherwise. Just wondering....
You can still utilize multiple links on the 2500 platform. If you create multiple interfaces with AP management enabled, you can load balance APs across the port(s).
Likewise, you can put your various wireless client vlans on different physical ports to avoid having ALL traffic on a specific port.
http://www.cisco.com/en/US/products/ps11630/products_tech_note09186a0080b8450c.shtml#scenarios
-Pat
Similar Messages
-
Does a 2504 WLC support mobility group with WiSM1 on 6500 Series
if a 2504 WLC support mobility group with WiSM1 on 6500 Series.
Model: WLC 2504
Software version: 7.3.101.0
Model: WiSM1
Software verion: 7.x.x.xYes and no.
Yes, mobility is supported.
No because I personally won't recommend inter-controller roaming. This is more true when you're dealing with 4400/WiSM-1. This is even more true when you've got WLC running two (or more) different codes. -
Port Configuration on new 2504 WLC
I've read some conflicting things on the new 2504 WLC's. Some things indicate all 4 ports are fully useable, while
others indicate perhaps only 1 or 2. I think I've read in product documentation that it support a max of two ap-manager interfaces. Does anyone know for sure if all 4 ports are useable? I'm thinking of the following configuration:
Port 1: management interface and first ap-manager interface
Port 2: second ap-manager interface
Port 3: first dynamic/client interface
Port 4: second dynamic/client interface
I'm planning on deploying my ap's in h-reap mode with a max of 25 ap's per 2504. Since I'm using h-reap, bandwidth shouldn't be much of an issue so I'm also considering trimming it down to using just two physical ports as follows so I can take up fewer gig switchports which are scarce at many of my locations:
Port 1: management interface and first ap-manager interface
Port 2: first and second dynamic/client interface
Opinions? I've always deployed 4400's and 5508's with LAG so I haven't had to think about this much until now.Hi Evan,
For sure! There is a really good example on the configuration guide, and assciated caveats.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0100011.html
Benefits for using LAG is increased bandwidth, and redundancy - especially if you have the two (or more in the case of a 5508 WLC) ports connected to different physical switches, eg a 3750 stack.
Best,
Evan -
How-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device
Dear All
I have a 2504 Wireless Controller with multiple radios attached. I currently have a "private" WLAN configured (taking ip from windows server based DHCP of Range 192.1681.0/24 ) and working, but I need to add a Guest/Public WLAN which should take the IP from Other DHCP Configured on Fortigate UTM of range 172.16.0.0/24.
We have one SG300 switch in the office and the rest are basic switches.
Our firewall/router is a Fortigate UTM 240D
Find the attached network diagram for the issue.
Is there a SIMPLE way to enabling guest access that doesn't require VLANS (or are VLANS easier than I'm making them)?
Thanks.
- See more at: https://supportforums.cisco.com/discussion/12473186/how-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device#sthash.aj1XcWI0.dpufComplete these steps in order to configure the devices for this network setup:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html
Configure Dynamic Interfaces on the WLC for the Guest and Internal Users
Create WLANs for the Guest and Internal Users
Configure the Layer 2 Switch Port that Connects to the WLC as Trunk Port -
Configuring 2504 WLC for LanSchool/AppleTV
Good Day to All,
Recently my small elementary schools have upgraded to Cisco Air-Cap2600 series AP's and a 2504 WLC. Very much a sweet step up from 10 year old Apple Airport Extremes.
My question is what would be the best pratice to enable Multicast via the GUI for the needs of those platforms and any other future P2P services?
Thanks in advance from a newbie,
GEPWhat is the WLC software version running on your 2504 ?
If it is 7.4.x follow the below reference guide
http://www.cisco.com/en/US/docs/wireless/technology/bonjour/Bonjour_Deployment.html
If it is 7.5.x following config guide should help
http://www.cisco.com/en/US/docs/wireless/controller/7.5/config_guide/b_cg75_chapter_01011.html
HTH
Rasika -
WLC with LAG mode enable connected to a switch HP in LACP mode
I am trying to connect a WLC 4402 5.0.148.0 mode with an HP 2800 switch. The switch is configured thunk mode with LACP protocol.
The WLC in LAG mode uses the protocol LACP? How can configure them switch HP?
Thanks.
Mirko Severi.not supported, Mirko. Refer to this for further detail:
http://www.cisco.com/en/US/docs/wireless/controller/4.0/configuration/guide/c40mint.html#wp1186245 -
Local printers not working with 2504 WLC
I have a 2504 WLC with 3 1262 WAPs in lightweight mode.
Clients connect using WPA2 PSK AES with no problem. Clients are Windows XP Home SP3. Test pages end up in print queue and eventually get a error printing status. Clients are not part of a domain and in a standalone workgroup - techstream.
Printer can be pinged from wireless client.
Another 1262N WAP in standalone mode connected to same lan from windows 7 sp1 clients have no problem printing to a local printer.
What does work on the Windows XP Home client is connecting to a network shared printer authenticating with domain admin id and password and it works. Reboot and the network shared printer can not connect multiple reasons are "access is denied" and message box says "only security tab will be displayed....." Another Windows XP Home SP3 client on reboot can't open the network shared printer with message "Can't find printer"
The local printers do work on these pc's with an old colubris router that has an outside interface on our lan and internal network with clients getting dhcp address from colubris router of 192.168.3.XXX .
What is wrong with the wireless 2504 WLC?
Thanks
Broadcast forwarding was enabled.Although a cisco tech support was helpful in making sure multicasting was enabled and a multicast server defined, the problem was at the CP2025DN printer. It had old network ip mask and gateway configured on the printer.
The new devices were part of the new network configuration (Mask and gateway had changed). I didn’t change that printer when I changed all the other printers at the facility because it was still active thru the old wireless network. I forgot to change the printer ip config when I brought the new wap on the new wireless network with the wlc 2504.
End result was the clients were part of a different subnet and gateway configuration then the printer and this disrupted the communication between clients and the printer. Once I corrected the mask and gateway on the printer to be the same as the dhcp scope of the wireless network, communication and printing worked.
Problem solved. User error -
Please help me to configure 2504 WLC as secondary in N+1 HA mode. My primary WLC is 5508 and both have 50 AP license. I want to deploy the AP in the same location.
Go HERE: https://supportforums.cisco.com/discussion/12219106/high-availibility-2500
-
2504 WLC on edge network for guest wifi
I have a 2504 WLC with a 1042 AP and I have it placed on my edge Cisco 3750 switch.
I have the management interface of the WLC set on my WAN IP 71.x.x.x subnet range, and I have the WLC doing DHCP duties with a DHCP scope of 192.168.X.0. I have my DNS servers set on external DNS servers out on the Internet.
I have two Cisco 3845 Routers on my edge network - one for each ISP with BGP protocol.
Since my native VLAN is 71.x.x.x, I added a sub interface on my main core router and gave it a 192.168.x.1 255.255.255.0 address for the gateway. Also, I added ip prefix-list iBGP seq 10 permit 192.168.x.0/24 le 32 to my main core router. On my secondary ISP router I added
ip prefix-list iBGP seq 10 permit 192.168.X.0/24 le 32, and ip prefix-list OUT seq 10 permit 192.168.x.0/24 statements.
I added VLAN 10 to my edge switch and gave it IP 192.168.x.2 255.255.255.0, and the switchports that my core router and my WLC are connected to the edge switch, are in trunk mode with encapsulation dot1q 10. The switchport on my edge switch that the AP is connected to is in switchport access mode.
I can connect to the wifi with a 192.168.x.x IP address on my laptop, but I cannot get any Internet access.
Is it possible to have the DHCP scope be in a different subnet than my WAN IP subnet, and allow guests to get to the external Internet only? Do I need to put the WLC somewhere internal on my network i.e. the DMZ and then tunnel the traffic out to the Internet with no Internal network access?
Thanks for any help you can provide.right, and how does a 'normal/current' user access the internet? Somwhere going to your ISP there should be some sort of NAT statement when you send interwebs traffic.
if your ISP is taking care of all of that for you, you probably need to let them know you added the subnet so they can do the NAT.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Will the 2504 WLC internal DHCP give IP addresses to clients?
Is there a way to configure the 2504 WLC so that its internal DHCP only services the LAPs?
I don't want the controller to give out IP addressed to wireless clients.
ThanksNo.
DHCP on the WLC is never intended to offer DHCP services to any "wired" side devices, which includes your APs. These DHCP pools are specifically to hand addresses out to wireless clients attached to WLANs of the specific WLC it is configured on. Even then, unless you absolutely cannot offer DHCP somewhere else, DHCP on the WLC is not a suggested practice.
DHCP Pool Configuration and Restrictions.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-6/configuration-guide/b_cg76/b_cg76_chapter_01000110.html -
Configuring Guest Access using 2 LWAPs and 2504 WLC
Please advise,
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.
Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?Yes you can. You can have up to 16 SSIDs per AP, but not suggested to have all 16. You can either use one port on the 2504 for both SSID/vlan or specify which port is for corporate and which one is for guest.
Thanks,
Scott Fella
Sent from my iPhone -
Nokia N81 8gb camera :future not supported
i have mobile nokia N81 8GB . When i turn on camera then coming " camera future not supported". I re sttart also replace battary.. After same thing.
How can solve this .. Pls. Any one help me....?HI I HAD THE SAME PROBLEM TWO YEARS AGO WHEN I BOUGHT IT. THE ONLY SOLUTION IS TO SEND IT TO A NOKIA SERVICE CENTER TO REPLACE ONE OF THE PIECES WHERE THE CAMERA IS .THEY CHANGED AND EVERYTHING OK IT TAKE A LONG TIME TO REPAIR ABOUT 2 MOUNTHS BUT EVERYTHING OK .N81 IS A GOOD PHONE I STILL USE IT AND IS GOING WELL
-
Power adapter for cisco 2504 WLC
Hi all ,
Is there any other part numbers for cisco 2504 WLC power adpater other than
PWR-2504-AC= ?
Thanks,
Regards,
Vijay.No "PWR-2504-AC=" is the only power adapter option for 2504.
Please check the datasheet:-
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html -
Apple Devices on 2504 WLC with 5 APs
Hi All,
I have just setup 5 APs (1042) with a 2504 WLC, I have connected these devices in my home lab and will be deploying this later in a live environment. The WLC/APs will reside on the 192.168.210.x/24 subnet with the controller being on x.x.210.5 and the gateway (including the DHCP Server) being on x.x.210.1/24.
Here is my issue, I have configured my WLAN to use WPA+WPA2 with AES & TKIP using a Preshared Key but I am finding associating to the wireless network very slow on my Windows PC and, even worse, now connection from my iPad (I should mention the Windows PC is stable once connected).
I can see both devices seen by the APs when I look at the client list:
MAC Address AP Name Status WLAN/RLAN Auth Protocol Port Wired PMIPV6 Role
08:ed:b9:48:19:cd SD-2f.55 Associated 1 Yes 802.11n(5 GHz) 1 N/A No Local
98:fe:94:7f:7c:1a GSD-39:49 Associated 1 Yes 802.11n(5 GHz) 1 N/A No Local
The iPad (98:fe...) doesn't get an IP address
(Cisco Controller) >*DHCP Socket Task: Jul 14 17:35:20.006: 98:fe:94:7f:7c:1a DHCP Forwarding DHCP packet (332 octets) -- packet received on direct-co
ect port requires forwarding to external DHCP server. Next-hop is 192.168.210.1
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP received op BOOTREQUEST (1) (len 308,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 1 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 1 - 192.168.210.1 (local address 192.168.210.5, gateway 192.168.210.1, VLAN 0, port 1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 2 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 2 - NONE
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 1 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 1 - 192.168.210.1 (local address 192.168.210.5, gateway 192.168.210.1, VLAN 0, port 1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP xid: 0x359ad7fb (899340283), secs: 25, flags: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP chaddr: 98:fe:94:7f:7c:1a
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP siaddr: 0.0.0.0, giaddr: 192.168.210.5
*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP sending REQUEST to 192.168.210.1 (len 346, port 1, vlan 0)
*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP selecting relay 2 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
(Cisco Controller) >*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP selected relay 2 - NONE
*DHCP Socket Task: Jul 14 17:36:28.457: 08:ed:b9:48:19:cd DHCP received op BOOTREQUEST (1) (len 308,vlan 0, port 1, encap 0xec03)
I hope someone can guide me in the right direction as I wonder if my configuration is incorrect. Thanks in advance.
Additional Info:
---------------Show Interface ---------------
Interface Configuration
Interface Name................................... management
MAC Address...................................... f0:29:29:89:1d:80
IP Address....................................... 192.168.210.5
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.210.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.210.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Interface Name................................... virtual
MAC Address...................................... f0:29:29:89:1d:80
IP Address....................................... 1.1.1.1
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
---------------Show port summary---------------
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 100 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable DisableThanks,
I am making sure that I do that , but still to no avail. I am going to mess about with the 'Global', 'Enabled', 'Disabled' parameters (in the Controller - Interface -DHCP Information section) to see if that makes any difference. -
Help required to implement Cisco 2504 WLC and 1042 Access Points
Hi,
My name is Vidya Sagar. I am new to Wireless technology. We are planning to implement Wireless in our office. I have given the requirements below. Kindly go through the details and let me know how to start.
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.
I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
Please give me a implementation plan to do this. I would like to use LDAP or ACS for authentication purpose.
Regards,
Vidya SagarLets just do this simple first before you start using ACS as that will require a certificate installed on the ACS for using PEAP.
So first off, the WLC we will say is in vlan 10. When you are going through the startup wizard, make sure you define the vlan tag to 10 on the management interface. Make sure your virtual interface is an IP address that is not routed in your network, like an out of band IP.
Make sure the WLC time is correct or use NTP!!!!
Now you should be able to http or https to the WLC. I would upgrade the code to v7.4 and install the FUS image. Please reference this link for the upgrade procedure. You don't have to upgrade now... I would wait till you get everything working first.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
Now I would connect the APs on the same vlan as the WLC for now. Make sure there is dhcp on that subnet. Once the APs have joined, then you can move them to any subnet you want. Since you don't have many APs it would be okay to leave them in the same vlan as the WLC management or out them on any other vlan you choose. The APs will be connected to an access port NOT a trunk port!!!!
The WLC will need to be connected on a dot1q trunk port only allowing vlans 10,100,116,121. The 2504 running v7.4 will support LAG (etherchannel). Any ways, your switch port should look like this for example only
Interface gigabit1/0/1
description WLC2504
switch port trunk encapsulation dot1q
switchoort mode trunk
switch trunk allowed vlans 10,100,116,121
spanning-tree portfast trunk
channel-mode group 10 mode on << only for v7.4 if you use lag
Don't connect all four ports right now, just port one!!!!
Your Guest vlan, you will need to create an ACL to block traffic from accessing the internal network. You might want to allow dhcp and DNS bit I would leave it open first until you can verify everything is working.
Now on the WLC you need to create a dynamic interface for vlan 100, 116, and 121. If you click on the Controller tab in the GUI and click on interfaces on the left hand side, that will take you to where you can add/delete/modify your interfaces. When creating these interfaces, make sure you add the dhcp server IP address for the primary and or backup.
Now that you have your dynamic interfaces created, its time I create your SSID. Now click on the WLAN tab on the GUI and click on WLAN and then on the too right select Create New and then click go. Select WLAN on the drop down menu and then for the profile name I would use the SSID name also for simplicity.lean e the WLAN id to 1 for this and 2 for the next and so on. After defining these and clicking Apply you can now define your SSID. On the General tab, enable the status and leave the radio policy to all for now, you can decide later what you want to use. Choose your interface you wan to place this SSID on and enable Broadcast SSID for now and leave everything else alone. Now click on the Security tab and on the layer 2 Security, leave it at WPA + WPA2, only check WPA2 Policy and for WPA2 encryption choose AES only. Now go to the bottom of that screen and choose PSk. We will do pre shared key for now so you get to understand the setup and make sure everything is working first. Now on the PSK format, choose ASCII and put your pre shared key in the input box. Make this simple to for testing. You don't want to put in symbols or anything like that. When you are don with that, check apply on the top right and test.
Now you can repeat this with your other SSIDs just to test. Your guest network you can leave open for now to test open authentication.
Here are some links for the WebAuth feature:
https://supportforums.cisco.com/docs/DOC-13954
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080b1a506.shtml
Now if you want to use ACS with PEAP, here is some links for that:
https://supportforums.cisco.com/videos/2499
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bd1100.shtml
https://www.google.com/url?sa=t&source=web&cd=8&ved=0CFQQtwIwBw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DWk_bRdmsQlA&ei=_BEyUeCYM8TdqAHHsICAAw&usg=AFQjCNF8PiVBQK1Kipb4j8AzD153bKtmgA&sig2=smHhNVmCr2of2NzbnDhGmw
Well that is it, hopefully you can get the wireless up for testing and verifying everything works!
Sent from Cisco Technical Support iPhone App
Maybe you are looking for
-
Where is the info window on itunes 11.1.3
Hello, I am looking for the info windows on Itunes. I dowloaded the new maverick and it disappeared. Someone could help me as I do not succeed in synchronizing my contacts with my iphone 4S iOS7 Many thanks in advance
-
Camera frozen after using FaceTime
Camera frozen after using FaceTime, have heard this is a common prob and need iPad replaced?!! Any quick fix?
-
On my Mac book pro, a grey progress bar will appear for a Little bit and the computer will shut down. What do I do?
-
Whole number rounding off in bom
is it possible not to round off whole numbers in the bom component quantity? for example, when i input the number 8.000, the system rounds it off to just 8.
-
Material Ledger for two materials
Hi, I need to run the Material Ledger for two specific materials. In CKMLCP not have the field to select the materials. In this case what should I do? hugs, Cristiane.