2504 WLC with 1552E AP's not able to wireless mesh

Good day all,
I'm seeking some assistance/help for a problem I'm havine with a WLC and 9 APs. I have a basic configuration on the WLC and I have configured one of the APs as the RAP. Now I try and add a second AP into a wireless mesh but it cannot see the RAP. They are sitting 5 feet apart but I don't see anything on the controller for the second AP. If I attach it to the wired network it can see the AP. RF-2 is solid green, RF-1 is dark, Uplink is dark, Status is orange. I understand that this means it's seeking for the RAP/MESH.
I've tried some debug commands but to tell you the truth I am by no means a wireless expert.
When the second AP boots this is what I see through the console
*Mar 1 00:00:52.515: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:52.775: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:52.803: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:52.827: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:52.827: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:52.843: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:52.843: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:53.071: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:01:46.827: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:01:53.491: %CDP_PD-2-POWER_LOW: All radios disabled - NON_CISCO-NO_CDP_RECEIVED (0000.0000.0000)
Any assistance would be great.

You still have two radios on the RAP just like the MAP. As long as you are powering up the RAP/MAP with the correct power source, the radios should come up. This means that you should have client access enabled by default on the 2.4ghz and 5ghz client access is optional. Juat make sure that the AP/RAP/MAP is in the correct AP Group and that the WLAN is present in the AP Groups. This will allow that WLAN to be broadcasted to the AP's in that AP Group. If your using the default group, then by default, all WLAN's 1-16 will be broadcasted, WLAN 16 and higher will not be unless you define the WLAN in the AP Group.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

HT1695 My new iPad with Retina Display is not able to connect to the Wi-Fi of my new Time Capsule. It used to connect, but now it just spins and spins and never connects. I've tried rebooting everything many times.

My new iPad with Retina Display is not able to connect to the Wi-Fi of my new Time Capsule. It use to connect, but now it just spins and spins and never connects. I've tried rebooting everything many times.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I am having issue with iphone 5 bluetooth , not able to connect honda CRV

I am having issue with iphone 5 bluetooth , not able to connect to my honda CRV

Don't know if you could consider this an Apple issue. I know you are probably frustrated, and I am not defending Apple here, just saying that the iPhone does not update to support individual automobiles, the automobile manufactures update to support the Bluetooth profiles.The iPhone has the latest Bluetooth stack and supports a number of things. Problems generally revolve around the manufacturer not supporting the lastest Bluetooth version and have to update their systems. Check with Honda, they are probably aware of this, and if you search the forum, you will find a number of posts regarding the CR-V.

Using the earbuds with clicker I'm not able to advance my music

using the earbuds with clicker I'm not able to advance my music

The Compatibility section here shows it's only compatible with the 6th generation iPod classic (2009): http://store.apple.com/us/product/MD827LL/A/apple-earpods-with-remote-and-mic

I have a Nikon Coolpix P510 and with Picasa I am not able to view videos or continous photos. Before I purchase Adobe Lightroom I want to know if I am able to view those features?

I have a Nikon Coolpix P510 and with Picasa I am not able to view videos or continous photos. Before I purchase Adobe Lightroom I want to know if I am able to view those features?

The best thing to do is download the trial of Lightroom and see if it works for you. The trial is the complete program. The only thing different about the trial is that it expires after thirty days. Your images stay in the folders you already have so there's little risk. Good luck!

Yesterday I have purchased Ipad2 with 3G but did not able see in built aceTime on my scree do we need to Install? please Help, yesterday I have purchased Ipad2 with 3G but did not able see in built FaceTime on my scree do we need to Install? please Help

yesterday I have purchased Ipad2 with 3G but did not able see in built aceTime on my scree do we need to Install? please Help, yesterday I have purchased Ipad2 with 3G but did not able see in built FaceTime on my scree do we need to Install? please Help.

See this support doc on how to use FT... http://support.apple.com/kb/HT4319

HT6147 With the latest iOS 7 update (Feb 2014) is anyone else experiencing trouble with the App Store not able even to load updates for existing apps, and unable to download new apps?

With the latest iOS 7 update (Feb 2014) is anyone else experiencing trouble with the App Store not able even to load updates for existing apps, and unable to download new apps?

With the latest iOS 7 update (Feb 2014) is anyone else experiencing trouble with the App Store not able even to load updates for existing apps, and unable to download new apps?

What's going on with the App Store not able to update 2015

What's going on with the App Store not able to update any apps 2015?

Apple is having server problems affecting App Store, iTunes, iCloud, etc…
Check the Apple Service Status(***) page… http://www.apple.com/support/systemstatus/ Wait for all systems to show green.
Here is what Apple's message says…
Multiple Store Services - All users are affected
     Customers may be unable to make purchases from the App Store, iTunes Store,
     iBooks Store, or Mac App Store.
iCloud Mail - All users were affected
     Users may have been unable to access iCloud mail.
iCloud Account & Sign In - All users were affected
     Users may have been unable to sign in.
This means no downloads, updates, iCloud and other issues. You may get pop-up windows asking you for password for iCloud, etc…
Try again after it's all green on status page.

LR 4 RC2 ...vexing problem, 3 sessions with support and still not able to find? With all settings re

LR 4 RC2 ...vexing problem, 3 sessions with support and still not able to find? With all settings reset and running a test catalog a raw image when opened in develop will when imediately going back to library view show a significant color shift in red, orange and purple but only in images with significant content in those colors. at first the culprit appeared to be camera calibration default but not reproducable. The problem exists even when opening older images from months ago? Also if second screen running in loupe mode the image is not shifted.
Any ideas please
Dave

Jim01403, Geoff and others...I'm new here so I'll need a little time The thread is very interesting, populated by serious mature people, how refreshing! It clearly is part of what i'm experiencing and is answered answered here...thank you. My main problem is still the significant color shift between develope and library modules. I'll attach one from each so you and others can see. Unfortunately the library version is the bad one so printing is now very problematic...Note, this occurs in either single or with second monitor on the library version is displayed. I have reset virtually everything and wonder if a cache is not updating or color space is not matching? A symptom/detail worth noting, when switching to library mode, the correct image is displayed for about a second then it jumps to what you see in the examples. As if the library module starts to rendering from develope settings then jumps tback to the original inedited preview??
Maybe just go back to 3.6 and tread water till 4.1 is fixed?
Dave

Problem with wlan sticks module, not able to write to disk any more

Hello everybody,
when I booted my PC today, a strange and some sort of severe problem occurred concerning my wlan stick(s) that I think, I'm not able to solve without your help. I searched for a solution but it didn't seem that somebody else has had a similar problem before.
Here is the description:
I have two wlan sticks (but I do not use both of them nor are they both plugged in at the same time), and both happen to malfunction since today. My "main" stick (used most of the time) is a BigTec Wireless 11N Adapter with a Realtek chipset. My second one (only used to solve problems with the other stick) is a Fritz! WLAN USB Stick (to be used with ndiswrapper).
After bootup, which makes no problems at all, my "main" wlan stick is not able to connect to the network. When I run wicd-curses (I use wicd as network manager), the virtual terminal freezes (when I use urxvt under openbox to run wicd-curses, only the window freezes). After one minute, a message appears that says something about a dbus problem but I am not able to read it because of the screen clears. Then I'm able to use the terminal again, but (and this is the very, very strange about this) when I run any program that tries to write on my disk it stucks, so I can't cancel it with ctrl-c nor can I kill the process. Wicd-curses, ifconfig or iwconfig also crash after entering the command and show the same behavior. At this point, my wlan stick does not show any sign of being plugged in (normally it blinks...).
My second stick makes the computer crash: After a few moments a stacktrace is shown (like when a kernel panic occurs), saying something about "stack being overrun". But I can't find the message in the log files so it is difficult to post it.
When I tried to figure out a solution, I saw in pacman.log, that yesterday udev and hwdetect were updated... But also downgrading all the packages that were updated yesterday did not solve the problem!
I'll post now the last lines of a few logs here (but nothing concerning the ndiswrapper stick, else it would be too disturbing), I hope they help you at helping me!
everything.log
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost kernel: [ 21.415035] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
Jan 23 15:25:27 localhost kernel: [ 22.063785] r8712u: 1 RCR=0x153f00e
Jan 23 15:25:27 localhost kernel: [ 22.064534] r8712u: 2 RCR=0x553f00e
Jan 23 15:25:27 localhost kernel: [ 22.170765] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost kernel: [ 22.410354] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
Jan 23 15:25:28 localhost kernel: [ 22.463386] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
Jan 23 15:25:28 localhost kernel: [ 22.463902] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:25:28 localhost kernel: [ 22.735037] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
Jan 23 15:25:29 localhost kernel: [ 23.383789] r8712u: 1 RCR=0x153f00e
Jan 23 15:25:29 localhost kernel: [ 23.384535] r8712u: 2 RCR=0x553f00e
Jan 23 15:25:29 localhost kernel: [ 23.490763] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running
Jan 23 15:26:12 localhost kernel: [ 66.495307] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin" # then I hard reset because of the freeze
errors.log
Jan 23 15:00:01 localhost /USR/SBIN/CROND[5597]: (CRON) EXEC FAILED (/usr/sbin/sendmail): No such file or directory
Jan 23 15:20:01 localhost /USR/SBIN/CROND[6215]: (CRON) EXEC FAILED (/usr/sbin/sendmail): No such file or directory
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running # then I hard reset because of the freeze
daemon.log
Jan 23 15:25:15 localhost [ 0.864888] udevd[48]: starting version 175
Jan 23 15:25:15 localhost [ 4.116488] udevd[235]: starting version 178
Jan 23 15:25:26 localhost dhcpcd[835]: dhcpcd not running
Jan 23 15:25:27 localhost dhcpcd[847]: dhcpcd not running
Jan 23 15:25:28 localhost dhcpcd[854]: dhcpcd not running
Jan 23 15:26:11 localhost dhcpcd[1382]: dhcpcd not running # then I hard reset because of the freeze
I hope you can help me and thank you for trying
hoeffl
P.S.: Excuse all the mistakes I made because of being new here, please!

This seems to be a problem with r8712u on all 3.2.x and 3.3-rc kernels on all distros. I've had it for weeks on Gentoo, Arch, and several other distros.
If you are running a 3.2.x kernel, this is almost definitely the problem. All 3.1 kernels don't do this.
I posted a temporary work-around on the Arch bugzilla, and Larry Finger (kernel dev with wireless) is currently working on it (a patch).
In the meantime, If you compile your own kernels, you can get 3.2.x's to work normally- see my comment here for more details. https://bugs.archlinux.org/task/27996
Top of page doesn't say r8712u, but it's the same problem, and after the first 2-3 comments it deals with r8712u specifically.
There is also info on the Gentoo forum 3.2 kernel quirks thread, towards the bottom of Page 1: http://forums.gentoo.org/viewtopic-t-901702.html
Last edited by wrc1944 (2012-02-03 07:45:32)

With iOS 8.02 , not able to connect Bluetooth devices

Not able to connect with my car audio and headphone after I updated 8.02

Hello sturmgraz,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: How to troubleshoot Bluetooth connections
http://support.apple.com/kb/TS4562
iOS: Troubleshooting car stereo connections
http://support.apple.com/kb/TS3581
iOS: Third-party Bluetooth accessories
http://support.apple.com/kb/ht1664
Best of luck,
Mario

Informatica 9.1 with oracle 12c. Not able to connect to the PDB while instalation

Dear Peers,
I installed oracle 12c on my laptop. And by default PDB created, TNS entries added for the same and successfully connected to PDB. In my PDB i created two users and I am able to connect with them also.
While installing the informatica server with 64 bit, in the part of domain configuration repository I am not able to connect to my users those I created. I am not able to connect to either CDB or PDB also. I am not able to get the what is the error is. But in oracle I am able to connect to my PDB with those users.
Any one overcome on this issues, Please help me.
Thanks
Raghavendra
<mod. action: phone number removed>
Message was edited by: Nicolas.Gasparotto

If you can connect using sql*plus from the same machine you are using informatica to connect from then you have an informatica issue and should try posting in an informatica forum.

Struck with Homeland security virus - not able to recover via safe mode nor by command prompt

my laptop hp 64bit windows 7home prem
the homeland security virus has blocked my laptop
m not able to anything....
for all safe mode, safe mode with networking and command prompt .. d laptop restarts and gets locked in normal mode
plz advice

Try a Kapersksy CD to boot the laptop:
http://malwaretips.com/blogs/homeland-security-virus/#kaspersky
Or, HitmanPro usb flash to boot from:
http://www.bleepingcomputer.com/virus-removal/remove-homeland-security-ransomware
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Licensing problem with UCCX 7, agent not able to login at all

Hi there,
We have UCCX 7 server and CUCM 7.
Problem is that we the agents are not able to login and they are getting maximum license error although not all licenses are used.
We get the following errors when trying to login:
1. "Maximum number of licenses reached. Please notify your System Administrator".
2. When we click "Ok" for the error above, we get the following "A licensing error has occured. Please try again in five minutes. If the problem persists, please see your log file or System Administrator for details.".
I checked the licensing service and it is working fine.
The log for the licensing service is not indicating anything, it shows only the last time there was a failure in this service (this was 6 months ago after a restart). It was working fine until yesterday.
I tried to disable the "IPCC Extension" under the User Configuration in the CUCM and enable it again, but did not solve the problem and got the same error.
It is worth to mention that when I disabled the "IPCC Extension", before I enabled it again, I tried to login using CAD but I got the same exact error.
Any help will be really appreciate, thanks a lot.

Hi
Open a command prompt on your UCCX server (not client) and go to this directory:
C:\Program Files\Cisco\Desktop\bin
Then run:
showlicenseusage.exe
THis will show you the IP addresses that are currently consuming licenses. You can check these PCs to see if they are still logged in - if they are, that's your problem. If they aren't, then you may have a problem with the LRM service or something.
If it has logins listed that aren't really logged in, you might be able to restart the License and Resource Manager service from Control Center to resolve it temporarily.
Aaron
Please rate helpful posts..

Apple Devices on 2504 WLC with 5 APs

Hi All,
I have just setup 5 APs (1042) with a 2504 WLC, I have connected these devices in my home lab and will be deploying this later in a live environment. The WLC/APs will reside on the 192.168.210.x/24 subnet with the controller being on x.x.210.5 and the gateway (including the DHCP Server) being on x.x.210.1/24.
Here is my issue, I have configured my WLAN to use WPA+WPA2 with AES & TKIP using a Preshared Key but I am finding associating to the wireless network very slow on my Windows PC and, even worse, now connection from my iPad (I should mention the Windows PC is stable once connected).
I can see both devices seen by the APs when I look at the client list:
MAC Address       AP Name           Status        WLAN/RLAN      Auth Protocol         Port Wired PMIPV6 Role
08:ed:b9:48:19:cd SD-2f.55          Associated    1              Yes 802.11n(5 GHz)   1    N/A   No     Local
98:fe:94:7f:7c:1a GSD-39:49         Associated    1              Yes 802.11n(5 GHz)   1    N/A   No     Local
The iPad (98:fe...) doesn't get an IP address
(Cisco Controller) >*DHCP Socket Task: Jul 14 17:35:20.006: 98:fe:94:7f:7c:1a DHCP Forwarding DHCP packet (332 octets)                  -- packet received on direct-co
ect port requires forwarding to external DHCP server. Next-hop is 192.168.210.1
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP received op BOOTREQUEST (1) (len 308,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 1 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 1 - 192.168.210.1 (local address 192.168.210.5, gateway 192.168.210.1, VLAN 0, port 1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 2 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 2 - NONE
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selecting relay 1 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP selected relay 1 - 192.168.210.1 (local address 192.168.210.5, gateway 192.168.210.1, VLAN 0, port 1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP   xid: 0x359ad7fb (899340283), secs: 25, flags: 0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP   chaddr: 98:fe:94:7f:7c:1a
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jul 14 17:36:04.184: 98:fe:94:7f:7c:1a DHCP   siaddr: 0.0.0.0, giaddr: 192.168.210.5
*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP sending REQUEST to 192.168.210.1 (len 346, port 1, vlan 0)
*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP selecting relay 2 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 192.168.210.5 VLAN: 0
(Cisco Controller) >*DHCP Socket Task: Jul 14 17:36:04.185: 98:fe:94:7f:7c:1a DHCP selected relay 2 - NONE
*DHCP Socket Task: Jul 14 17:36:28.457: 08:ed:b9:48:19:cd DHCP received op BOOTREQUEST (1) (len 308,vlan 0, port 1, encap 0xec03)
I hope someone can guide me in the right direction as I wonder if my configuration is incorrect. Thanks in advance.
Additional Info:
---------------Show Interface ---------------
Interface Configuration
Interface Name................................... management
MAC Address...................................... f0:29:29:89:1d:80
IP Address....................................... 192.168.210.5
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.210.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.210.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Interface Name................................... virtual
MAC Address...................................... f0:29:29:89:1d:80
IP Address....................................... 1.1.1.1
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
---------------Show port summary---------------
Port Summary
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE
1 Normal Forw Enable Auto       100 Full   Up     Enable N/A
2 Normal Disa Enable Auto       Auto       Down   Enable N/A
3 Normal Disa Enable Auto       Auto       Down   Enable Enable (Power Off)
4 Normal Disa Enable Auto       Auto       Down   Enable Disable

Thanks,
I am making sure that I do that , but still to no avail. I am going to mess about with the 'Global', 'Enabled', 'Disabled' parameters (in the Controller - Interface -DHCP Information section) to see if that makes any difference.

2504 WLC with 1552E AP's not able to wireless mesh

Similar Messages

Maybe you are looking for