2520 USB 3.0 port on side of tablet

I cannot get a USB 3.0 drive to connect to this port. I can connect the drive to the USB 2.0 ports in back of keyboard.
I am using a Cable adapter that goes from the USB OTG connections for samsung devices.
Same cable works OK with a SD card plugged in with an adapter.
SD card is 128GB, the external drive is 1TB.
Are there issues with such a large external drive?
Thanks

might be an issue with the drive itself or the cable not supporting such powered devices. i don't believe Nokia released an official microUSB 3.0 to USB 3.0 adapter cable, but i may be wrong. in this case, some tablets etc may not support higher-power draining devices that USB 3.0 on laptops/desktops do. this may be the case here mate.

Similar Messages

Side USB 3.0 ports in HP Envy 23-d250xt stopped?

I have the HP Envy all in one desktop, Model 23-d250xt.
There are two side USB ports and four rear USB ports. The two side ports no longer recognize peripherals (external HD or flash memory). The four rear ports are still active.
Any suggestions on how to re-enable the side USB ports?
Thanks in advance.
David
update: the side USB ports were powered but for some reason, were not recognizing devices that were plugged into them. I disabled the device then enabled the device and all is working fine now.
Hope this helps someone.

Here is what I did.
I took the battery out.
I took the bottom big panel off.
I took the small panel off for the wireless card to see if I could see the two screws that connect the usb 3.0 ports and luckily I did.
I check the tightness and the screws were in really tight.
I decided to unscrew the two screws and lifted the backend of the usb 3.0 board up a little bit. I then sprayed some CRC QD Electronic Cleaner on the contact areas.
I put the two screws back in and tightened them up as much as possible without stripping or breaking the board.
I put the panels back on and put the battery back in.
Started it up and to my surprise, the USB 3.0 ports worked perfectly.
Before the USB 3.0 port problem the motherboard was changed so maybe the contacts needed to be cleaned. That is my guess.
Pepe999, thank you for the responses. I appreciate it.

When I connected my iPod Classic or iPhone 4S to the right side USB port of my 2012 11 inches Macbook Air (128 GB SSD), I get a message from iTunes that I connected my device to a USB 1.1 port. I checked the specs, it's a USB 3 port. What's wrong?

When I connected my iPod Classic or iPhone 4S to the right side USB port of my 2012 11 inches Macbook Air (128 GB SSD), I get a message from iTunes that I connected my device to a USB 1.1 port. I checked the specs, it's a USB 3 port. What's wrong?

When I connected my iPod Classic or iPhone 4S to the right side USB port of my 2012 11 inches Macbook Air (128 GB SSD), I get a message from iTunes that I connected my device to a USB 1.1 port. I checked the specs, it's a USB 3 port. What's wrong?

Usb 2.0 port on the right side (beside thunderbolt port) of macbook air 13" 2011 is busted, one of the pins inside the usb port is bent, is this replaceable? saw the pix on ifixit that it is part of the logic board.

usb 2.0 port on the right side (beside thunderbolt port) of macbook air 13" 2011 is busted, one of the pins inside the usb port is bent, is this replaceable? saw the pix on ifixit that it is part of the logic board.

The fix is a new logic board. It might be tempting to turn off the computer and start poking around inside to fix it yourself but you risk separating the port from the logic board and doing even more damage.

USB 2.0 stopped being recognized by USB 3.0 port

Hey all,
Two days ago, I was syncing my iPod Classic (USB 2.0) with iTunes and I also had my USB 2.0 Time Machine drive plugged in (I do not think it was backing up at the time), both of these devices were plugged into the USB 3.0 ports on my 15" MacBook Pro (Mid 2012). All of a sudden, my MacBook informs me that both devices were disconnected. For the next 30 minutes, these devices connected and disconnected sporadically. I tried restarting my MacBook multiple times, I reset the PRAM multiple times, I reset the SMC multiple times, I booted into Windows 7 (I use Boot Camp) and both devices show up as unrecognized. They do not show up at all on the OS X (10.10.2) side of my computer. What's strange though, is that all USB 3.0 devices work perfectly. I tried an old USB 2.0 flash drive, didn't work.
Anyone have any thoughts? I have searched Google and these forums for the last two days to no avail.

To plug a 2.0 into a 3.0 you are using an adapter? Is this where the problem is? Even with the old flash drive? or did you also try using the 2.0 ports on your MBP? The adapter could be bad or the cables for your external devises. You did the steps you need to do to correct the problem. Other then that it would be a hardware problem. And you would need to take it to an apple store to be checked out.

USB 2.0 port no longer recognizes ext. HD; USB 3.0 seems fine W510

Have had several BSODs in last few days. Two of most recent referred to nusb3xhc.sys
Other symptoms: I have 3 WesternDigital 500GB ext. USB 2.0 HDs none of which are being recognized even when plugging directly in to laptop USB port rather than USB hub I usually use. Same USB port will show a small thumb drive. USB 3.0 laptop port still works. While the WD HDs are all older, worked several days ago but now never show up in Windows Explorer and the tray icon for USB never shows them as I typically click on the latter to eject an ext. USB HD.
Recent changes to laptop:
1) 6.1.2014 installed MS OneDrive (and also on tablet). version 17.0.4041.0512
2) Control Panel add/remove programs shows that Dropbox installed version 2.8.2 just before OneDrive
3) Subsequent to above I did routine Windows update of Important items with no problems. However for several years since about IE 9 or perhaps 10, I have been unable to get IE to install and work, and have been using Chrome for years. I mention this to give fuller picture, but doubt that it is related to current issue.
4) Aside from typical routine updates e.g. Java, Bitdefender antivirus I have not intentionally installed any other software recently.
============
I have barely begun using MS OneDrive so am happy to uninstall it, or go to restore point prior to its installation. BSOD prior to this might have occurred 1 or 2x per year.
I'm pretty good at following directions if they are complete e.g. need full path if you want me to find something on my HD.
Lenovo website for machine type 4318CTO running Windows 7 Pro 64-bit indicates that driver version for USB 3.0 dated 1/22/2010 versin 1.0.19.0 is up to date and that it is NEC device. Device Manager also says is up to date. There is one USB 3.0 port on rear of laptop and two USB 2.0 on side. HP website shows more recent NEC USB 3.0 driver dated 9/16/2011 version 2.0.32.0
Thanks for your knowledge, skill, and help.

I always thought that high-speed USB was USB 1.1. I thought that USB 2.0 was full-speed. But my iMac Core 2 Duo has USB 2.0 (I'm sure) and it says that my iMac has a USB High-speed bus.
Your PowerBook G4 might need service, go to your local Apple Store and see someone there about it. I'm pretty sure that you have a hardware problem.
Steps:
1. Try connecting another USB 2.0 device to that same port. If the device works you have a problem with your iPod. (This is a long shot.) If this happens you should reinstall iPod software.
2. Try reinstalling iTunes.
3. Try calling AppleCare technical support.
4. Try reinstalling Mac OS X. (If AppleCare hasn't told you do this already.)
5. You have a hardware problem. Go to an Apple Store to get it fixed.

USB 3.0 port thinks it is USB 2.0

I just bought a new HP ENVY 15-j101tu Notebook PC. When I plug the external USB 3.0 hard drive the system pops up message saying the device can perform faster when connected to USB 3.0. The speed of file transfer from laptop to the external hard disk is then very slow. To my understanding this laptop comes with all USB 3.0 port.
Please help to fix this problem. Many thanks in advance

The usb ports on the right and left hand side are usb 3.0.
What is the brand and model of your external usb 3.0 hard drive?
Have you tried the usb 3.0 external hard drive on a different PC to see how Windows reacts to it?
Connect a usb 3.0 usb flash drive to all ports to see how the notebook's OS reacts.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Why is the usb input on the left side ?

for the love of god, what exactly stood behind the design of putting the usb input on the left side of the laptop ?
for right handed plugging in their mouse, the cord has to go all the way around to reach the right side.

There is a port next to the modem connection on the back right side. You knew that. wow no big deal. I thought there were too few USB ports but there are plenty. How many usb devices does one need to plug in simultaneously?

Lenovo Thinkpad E530 - USB 3.0 Ports Not Working Code 10

Hi everyone, so I own a Lenovo E530 with Windows 7 and just earlier today I plugged in my optical mouse into it, about 10 minutes in, Windows gave me a "not enough power message" for my USB 3.0 ports on the left side and they just stopped working. I have 3 USB 3.0 ports on the left side of the laptop, and one USB 2.0 on the right which works just fine.
From there it gave me Code 10 for Teredo Tunneling Pseudo-Interface in the Network Adapter section (which I was able to fix via a registry change) and now what is left to fix is the Intel USB 3.0 eXtensible Host Controller which I cannot seem to fix. I have tried the uninstall/reinstall processes, with Intel's own drivers and Lenovo drivers which were just older version of the Intel USB 3.0 drivers, over and over yet it is still stuck on Code 10, where it will not start.
I never really overused the USB ports either, aside from plugging in a portable USB fan and portable hard drive here and there, and a USB dongle for a wireless mouse and keyboard (Logitech all-in-ones), that is pretty much all I have done with it. I do not believe the ports are not bad or anything, although it may be a hardware problem, but all 3 USB ports still give power on my fan and external HDs when I plug it in, it is just that Windows does not recognize it and nothing happens when I plug something into. But on the other hand, the USB 2.0 port reads just fine and recognizes everything. I have also tried the Troubleshooter multiple times, but everytime it tries to reinstall I get the "Failed" message.
Here is a screenshot of what I am talking about.
http://i.imgur.com/mKqWpFU.png
http://i.imgur.com/RLkbyHY.png
I have tried reinstalling and uninstalling the Intel USB 3.0 eXtensible Host Controller Driver for W7 using the ones listed on the drivers page through Lenovo and using the newest version fround on Intel's webpage as well. Having done these I still could not get it working, so I did a full reformat of the Hard Drive, from there I am able to get the USB 2.0 and 1 of the 3 USB 3.0 ports to work (the very top one above/left of the HDMI port) and recognize devices when I plug them into Windows. But this is working through not having the USB 3.0 Driver installed and just the basic one without having any updates/drivers installed on. Once I install the USB 3.0 Driver back it, it goes back to the original problem.
The problem still persists even though I have done multiple reformats, uninstall/reinstalls, updating to newest drivers and BIOS, etc. I have owned and still own a whole family of Lenovo laptops which still work perfectly fine, but this is the first time I have seen anything like this go wrong in a laptop. Is there anything else I can try to fix this problem? The laptop just went out of warranty a few months ago, and if I were to send it in and get it repaired would it cost me a lot?
Lenovo Thinkpad Edge E530 w/ i5-3210M
Lenovo Thinkpad X230t w/ i5-3320M
Lenovo V570 w/ i5-2410M
Lenovo Thinkpad Edge 14 w/ i5-480M

Hi,
Can you try this
The Device You're missing drivers for (PCI\VEN_1022&DEV_7814&SUBSYS_380217AA&REV_01) is definitely for AMD USB 3.0, this one's off from AMD WEbsite
http://support.amd.com/us/gpudownload/windows/Pages/raid_windows.aspx#2
download the AMD Chipset Drivers see if that'll work.
Have you installed the energy management?
If not please install this as well, I'm thinking this is what the other device is for.
Lenovo Energy Management
emw7034.exe
21.4MB
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Our HP 1150us g7 has stopped recognizing our dual USB 2.0 Port. It is not listed to uninstall and

Our HP 1150us g7 has stopped recognizing our dual USB 2.0 Port. It is not listed to uninstall or update its' drivers. Only the one USB port works on the right side facing the notebook.
It is only 21 days out of warranty and I am told they can be replaced however it takes a huge amount of labor, then someone else told us it can not be exchanged only the entire Motherboard. I have found the exact part on sale so I believe it is replaceable.
Here is a link to order the part we believe can be replaced.
http://www.machinaelectronics.com/store/buypart.cfm?pn=NL028516
Does anyone know if it is replaceable or not?
We are sick about this we only had the notebook one year and for the warranty to run out only 21 days before this died we are disappointed with HP for not providing some assistance.
This question was solved.
View Solution.

The link you provided is not the same model as yours. While it may work, I haven't verified it.
Have you performed any hardware troubleshooting on the unit yet?

Does the HP ENVY 15-j027tx Notebook have USB 3.0 ports?

Hi there, Can anyone please advise whether or not this particular model has USB 3 ports? or some USB 3.0 ports?
HP ENVY 15-j027tx Notebook
Thank you

Hi: The user guide for your model indicates that on the left side of the notebook there is a USB3 charging port and one USB3 port. See chapter 2, page 5. http://h10032.www1.hp.com/ctg/Manual/c03735710

Which are the USB 2.0 ports and USB 3.0 ports?

Purchased a hp DV7-6143cl. Which are the USB 2.0 ports and USB 3.0 ports?
Thanks

USB 3.0 may be a different color.
Left side USB ports are 3.0
Right side are 2.0
See your Service guide (page 19)
Main page for your model

How do I disable only the USB 2.0 ports - K7T266 Pro2-RU

None of the USB ports on this MB will work with my Biostar 6-in-1 card reader - however, I have a VIA USB 2.0 PCI card that works fine with it. I want to disable the 2.0 ports only, and install the PCI card. The manual is not very helpful - if I only enable USB 2, which seems to be the USB 1.1 header, that DOES disable the USB 2.0 ports, but it also disables the 2 USB 1.1 ports on the MB!

Yes, and they are labled USB1, USB2 and USB3 - now I assume that these correspond to the JUSB1, JUSB2 and JUSB3 headers on the MB, with JUSB2 being the 1.1 ports on the D-LED bracket, and JUSB1 and JUSB3 being the 2.0 headers. I can only ENABLE certain USB ports in the BIOS - i.e. if I only enable JUSB2, this effectively disables the 2.0 ports - aha - it also disables the 2 1.1 ports on the back of the MB itself!!
Any other answers?

HP 2005pr USB 2.0 Port Replicator - Video not with my Surface Pro 3

Hi everyone,
I've spent tons of hours already trying to get the HP 2005pr USB 2.0 Port Replicator working with my Surface Pro 3 and no luck. I mean, the USB replication / hub works, meaning that if I plug in a USB mouse / keyboard, they work. It recognizes the device in Device Manager and the ViewSpan application is running. But if I plug in a display in the VGA, nothing happens, no monitor gets detected, and even if I "force-detect" one it still doesn't display anything.
I've tried with 3 driver versions so far:
0.2.5 - not working at all. Reboots my Surface while installing. (this one is on the device itself).
3.X - which is the first with support for Windows 8 I think. I can install it and everything works as described above - meaning no VGA.
5.3.X - same story as above.
I've tried uninstalling, restarting and uninstalling several times with both versions. No luck. And I've literally been on every forum where people have problems with the replicator and nothing helped.
Anyone had any luck getting such a setup to work?
Or any ideas on how to get it to work?
Thanks.

Hi @blinkk2
I see that you are having problem connecting an external monitor to your Microsoft Surface Pro 3 through the HP USB Port Replicator. As the USB ports are working with the mouse and keyboard we know what the Port Replicator itself is working this is going to be something with the drivers on the Surface. I would recommend contacting Microsoft Support to see if they can recommend a graphics driver for you.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Mac Pro USB and FW800 ports not working

I've been reading tons of forum entries in the Apple Support Community and in other forums. Nothing seems to answer quite what's going on with my Mac Pro Tower.
Here are the details and steps taken up to now:
- I'm running a Mac Pro Tower (MacPro 3,1, 2x 2,8GHz Quad Core, Early 2008 model), currently running OS 10.6.8
- I moved before the holidays in December and left my computer unplugged for over month while away. Didn't have any issues before the move.
- up until the last couple of weeks, I had actually been running on Leopard (yes, I'm a luddite!, please, no teasing )
- I was trying to update my ipod touch's iOS and kept getting errors preventing it from completing the process. At first I thought it was an ipod app causing the issue after having read a few threads on that topic...
- Also, on startup, the Mac started searching for a Bluetooth keyboard, of which I don't have, and would not detect my usb keyboard. I would disconnect and reconnect the keyboard and the majority of the time, the Mac would then recognize my USB keyboard.
- I decided to upgrade to Snow Leopard, which didn't help with the iPod update. I did not do a clean install.
- Then I noticed that my USB stick wasn't working and tried it in all the usb ports (except the ones on the keyboard)
- Also, I had removed and then reinstalled printer and scanner drivers for my All-in-one printer. After this I kept getting constant communication errors between the mac and the printer via the usb port, although I was able to print a test page.
- I've used Hardware Test once which didn't detect any issue.
- I reset the SMC
- I reset the PRAM, and for a few seconds I was able to read from my USB stick, then never again, even after another PRAM reset.
- I've cleaned the whole inside of the computer and checked for loose cables. Cables are in so tight it's so hard to loosen them!
- I now tested all the ports:
     ∞ the 2 front and 3 back USB ports are unresponsive to my usb key and to my VoyagerQ dock
     ∞ the front and back FW800 ports are unresponsive to my VoyagerQ dock
     ∞ However, the keyboard works in any fo the back ports and my USB stick is recorgnized by the USB port of the keyboard.
     ∞ I also plugged in my Logitech webcam into the keyboard and it works there but not in any other port.
     ∞ When I plug in USB powered speakers into any of the ports, they work fine
     ∞ And the FW400 ports are also working fine with my VoyagerQ dock
- a few times, including once today, my mac restarted by itself. The times before today, I thought it was because I was sort of moving back the computer in place, but today I was nowhere near the computer.
So what does this all mean? Should I do a clean install of the Mac OS? Or is it a problem with my Logic Board?
Any insight please would be helpful. I had Apple Care and missed the reminder to renew it so I really hoping not to spend more money than necessary.

Thanks Grant,
The battery is a start and something inexpensive to replace.
I did do a PRAM reset (command + option + P + R) and was able to hear the chime 4 times. I tried resetting it a number of times over the past week, as well as yesterday with no success in reviving the USB ports. But isn't it weird that my USB powered speakers work by plugging them in any USB port (with the mini jack pugged in the back or front earphone plug)?
I did not use the USB ports on the keyboard until yesterday, so that is not the cause of the other USB and FW800 ports failing. But I'll follow your suggestion and not use them except for the mouse.
Another weird thing that happened yesterday, I have 16GB of RAM and I spent all day trying to troubleshoot a RAM issue that is magically fixed after leaving the computer on overnight to do an extended Hardware Test. The issue was:
- Only 8 RAMS were being recognized
- a red LED light appeared on the top riser
- first I thought I had isolated the faulty RAM bar, and then a second one
- Then going pair by pair again, I no longer saw the LED light
- Put back all 8 bars, only 8 GB of RAM recognized
- Left computer overnight running Hardware test (said it took almost 3 hours, with no errors)
- Now all 16 GB are recognized!
Thanks again for the tips

2520 USB 3.0 port on side of tablet

Similar Messages

Maybe you are looking for