2602 lightweight AP losing config on reboot

Anyone encountered an issue with the 2602E access points losing config everytime they lose power?
I have a 5508 WLC running 7.4.121.0 code and two 2602E Flexconnect access points that everytime they lose power they default their configuration. The APs are located at a remote site connected via MPLS and are configured for FlexConnect with local switching. The 2602Es will re-associate with the WLC since the DHCP option 43 points them to it, they just show up with the default config.
I have three 2602E models at the site but only two of them are doing this, the third comes back up and associates and has retained its configuration. I also have several 1142 models at the site and they behave normally.

There are no secondary controllers, just the primary. These two access points lose all configuration, name, ap group, flexconnect group,flexconnect setting, everything. Its like they are new out of the box and associating for the first time. I have a third 2602E located att the same site and have tested it via power reset and reboots and it retains all config. Both the AP that retains its info and the two that dont are all running the same code/boot version/etc. I cant see any difference in their configuration.

Similar Messages

  • 8330 keeps losing power and rebooting

    my curve 8330 keeps losing power and rebooting, does anyone know how to fix this, tried cleaning battery terminals but did not work.

    I also have a 8330 and it does the same thing.  It randomly resets (like a master reset as it takes a long time to reboot) throughout the day.  I am a Canadian user and talked to Bell who told me I had to send the phone in.  I went to one of their stores and sent the phone away for 2 weeks.  I received it yesterday as it was "repaired".  I had it less then 24hrs and again it reset about 12 times during that time.  I am also not able to activate Enterprise since the repair.  My company exhausted it's options to help me set it up but they determined the is a hardware issue.  So The problem is worse now.  I have tried with and without media card and it doesn't change anything.  I have waste days with Bell trying to resolve this issue as technical support on the phone confirms that it is a hardware problem.  I have now had to take the phone back to Bell for repair again.  I am shocked with Bells attitude concerning this problem as I have talked to numerous customer service managers that tell me that I have a contract with them to provide the "service".  They don't seem to care that the hardware doesn't allow me access to their service.  I am also amazed that they don't care that a customer has to waste time on tech support phone calls and traveling to their stores to ship the phone back to Blackberry.  As well as my company that wasted time setting up my "loaner" phone then my regular phone after repair and then again a "loaner" phone when nothing was fixed.  When does Blackberry get involved and make the customer happy?  I am surprised that the cell phone providers can not issue a new phone when there is a hardware problem under warranty.   I was told by Bell that Blackberry typically needs to see the phone 5-7 times before they will issue a new one....  This translates to the customer doing 10-14 trips to the store and a large amount of time setting the phone back up each time...  
    Unless something happens fast, my company is buying out my contract with Bell and I will be switching to a competitive smartphone.  This is unfortunate as I like Blackberry but can not stand the support.  (since I can only talk to Bell as Blackberry won't talk to me directly and only directs me to my cell provider)
    Very Frustrating.  But a hardware problem for sure.

  • Fix for X-grid agents losing their config across reboots??

    Hello,
    We have a podcast producing system with 5 servers, 3 of which are Xgrid agents,
    and one of the others is the Xgrid controller. Sometimes we need to reboot some
    of the machines, and when we do the whole Xgrid set up goes. We need to go in to
    XGrid Admin, remove the agents, and re-add them, then log in to each agent, and start/configure Xgrid to find/join the XGrid again. Even though Xgrid is set as a service on these Xgrid agents, and they were previously configured. All XServers
    are running 10.5.5. Is this normal, or how do others manage to keep their Agents
    in the Grid across reboots? Thanks - Paul

    screw it.. i dunno... bad drivers, that's what i'm accounting it to. Nobody seems to know what the problem is anymore.
    With that said, the card works wonderfully now =D
    Someone on this board mentioned some third party drivers, so I went and found them. I had no troubles installing and have had no troubles with the drivers
    since their installation a few days ago.
    These drivers are not supported nor created by Creative (as far as I know). Use the drivers at your own risk.
    First, go to this address and read up on their drivers and how to install and what not. All the posts you should care about are sticked, so read the stickies!
    http://www.youp-pax.org/forumdisplay.php?fid=3&page=
    I noticed that the links to their drivers are lousy/don't work. Some nice person went and hosted all their files on a different site.
    http://hosted.filefront.com/robertmc84
    Be very cautious when downloading their drivers from filefront. The host has numerous old versions up and the file names aren't always 00% copy/paste from
    the YouP Pax site, so be certain you have the right file before downloading/installing.
    READ THE STICKIED INSTALLATION GUIDE! Same thing as with the installing Creatives' drivers, if you don't completely uninstall former drivers, bad things happen.

  • Apache service reset config on reboot

    Hi to all,
    i upgraded one of my servers from SnowLeopard Server (10.6.8) to 10.9.4 Mavericks Server, all services migrated fine
    except for Web Service, in this case i needed to rewrite in every virtual host file <mod_rewrite> and <Directory> sections because
    some of these setting didn't migrate in new config files (Now under /Library/Server/Web/Config/sites instead of "classic" /etc/apache2/sites).
    The problem is that OsX doesn't keep modified settings in config files after a reboot so i need every time to rewrite them.
    It seems that OsX restore them to "default" deleting only <mod_rewrite> and apache "basic authentication" inside <Directory> section...
    Taking a look at logs didn't help because there isn't an error related to apache. I tried also to to run "apachectl -t" but syntax is OK..
    Any idea?
    thank you

    Put your stuff in a separate file and place an include directive in the apple managed file.

  • CSS11000 does not take config after reboot with new image

    CSS11000 was upgraded with new IOS image.
    However, it did not take the current config (which was 'wr m') when rebooted from the new image. It seemed to have taken the config from another disk partition -?!. We had to revert back to the old boot image....then it worked (with the right config).
    Being unfamiliar with CSS's, I'd appreciate any expert's hints on this. Thanks!

    When you upgrade/downgrade to a version you have previously run, the CSS will restore the config you had when you ran that version the last time.
    I haven't bothered to check the docs or figure out myself, how to disable this behavior.
    I just get a copy of the config via FTP before i boot the new version, and then i FTP it back and reboot again, this usually works although i have seen it dump the config ones.

  • Messaging and Social Networking Widgets Losing Settings After Reboot...

    I'm having problems with my Messaging and Social Networking Widgets losing all of their settings after a reboot (power off/on).
    Is anyone else seeing this? Is there a fix for this issue?

    Try doing a phone reset by removing your battery for 5 seconds then place it back in and power your phone on.  You may have to add the settings back. For more information on widget settings click here http://motorola-global-portal.custhelp.com/app/answers/detail/a_id/48507/kw/widget%20settings/p/30,6720,7500,/session/L3NpZC9BN0VVdzY3aw%3D%3D.  Hope this helps!

  • ACCESS POINTS LOSING CONFIG CAPWAP

    I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
    Wlc 5508
    Ap 1242
    7.0.220.0
    Sent from Cisco Technical Support iPad App

    You mean anything 5.x, no but I might have to .. So Im told a bug was open for this .. I will update thread as this progresses.
    "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin

  • Win 98 forgets PCI-1200 config on reboot

    Problem: When Windows 98 reboots, it seems to forget the configuration of
    our PCI-1200 board - it looks to be OK in NIDA and device manager, but when
    I run the test panes, I get the message 'The device is not responding to
    the selected base adress' or similar. In some cases Windows crashes when
    I try to launch the Test Panels (NI-daq 6.5). Deleting the PCI-1200 board
    from the device manager and reinstallign it solves the problem - until the
    PC is rebooted next time.
    AT first I thougt it was a defective board, but we have seen similar behaviour
    with other examples. Has anybody any idea what's wrog? A solution?
    Regards
    Jens B Kristensen
    Denmark

    Have you already found the solution to your problem? Please reply to group.
    Device manager
    not showing Yellow marks and then device not working is not exceptional.
    Rishipa
    Reply to this group
    ============================================================
    Jens B Kristensen wrote in message
    news:[email protected]..
    >
    > Problem: When Windows 98 reboots, it seems to forget the configuration of
    > our PCI-1200 board - it looks to be OK in NIDA and device manager, but
    when
    > I run the test panes, I get the message 'The device is not responding to
    > the selected base adress' or similar. In some cases Windows crashes when
    > I try to launch the Test Panels (NI-daq 6.5). Deleting the PCI-1200 board
    > from the device manager and reinstallig
    n it solves the problem - until the
    > PC is rebooted next time.
    >
    > AT first I thougt it was a defective board, but we have seen similar
    behaviour
    > with other examples. Has anybody any idea what's wrog? A solution?
    >
    > Regards
    >
    > Jens B Kristensen
    > Denmark

  • WDS losing config.

    some of the WDS in my wireless network loose thier client config every once in a while and users cannot authenticate untill i reconfigure. why?

    Ensure that the mobility network-id command is not enabled on the Cisco Access Point (AP) if it serves as the Wireless Domain Services (WDS) device. The mobility network-id command is used for Layer 3 (L3) mobility, and the AP configured as a WDS cannot provide L3 mobility. This command must only be enabled when a Wireless LAN Services Module (WLSM) is used to provide WDS. A WLSM must be the WDS device to properly configure L3 mobility.

  • Facebook losing login after reboot

    I don't seem to have anything untoward in my Cookie or Security settings, but quitting and restarting Safari doesn't give me the problem, only rebooting does.  Then my login to Facebook is gone.  Both username and password have disappeared, even though I had the checkbox to save it checked.  Safari 6.1.6, Mac OS X 10.7.5, latest security update.    Here's the Etrecheck result if it makes any difference:
    EtreCheck version: 2.0.11 (98)
    Report generated November 30, 2014 9:13:35 PM EST
    Hardware Information: ℹ️
      MacBook Pro (15-inch, Mid 2009) (Verified)
      MacBook Pro - model: MacBookPro5,3
      1 2.66 GHz Intel Core 2 Duo CPU: 2-core
      4 GB RAM
      BANK 0/DIMM0
      2 GB DDR3 1067 MHz ok
      BANK 1/DIMM0
      2 GB DDR3 1067 MHz ok
      Bluetooth: Old - Handoff/Airdrop2 not supported
      Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
      NVIDIA GeForce 9600M GT - VRAM: 256 MB
      NVIDIA GeForce 9400M - VRAM: 256 MB
      Color LCD 1440 x 900
    System Software: ℹ️
      Mac OS X 10.7.5 (11G63) - Uptime: 0:6:31
    Disk Information: ℹ️
      FUJITSU MJA2500BH FFS G1 disk0 : (500.11 GB)
      S.M.A.R.T. Status: Verified
      disk0s1 (disk0s1) <not mounted> : 210 MB
      Macintosh HD (disk0s2) /  [Startup]: 456.14 GB (112.89 GB free)
      Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
      10.9 (disk0s4) /Volumes/10.9 : 42.46 GB (30.70 GB free)
      Recovery HD (disk0s5) <not mounted>  [Recovery]: 650 MB
      MATSHITADVD-R   UJ-868 
    USB Information: ℹ️
      Apple Internal Memory Card Reader
      Apple Inc. Built-in iSight
      Apple Inc. BRCM2046 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Computer, Inc. IR Receiver
      Apple Inc. Apple Internal Keyboard / Trackpad
    Launch Agents: ℹ️
      [running] com.epson.epw.agent.plist Support
      [loaded] com.oracle.java.Java-Updater.plist Support
    Launch Daemons: ℹ️
      [loaded] com.adobe.fpsaud.plist Support
      [loaded] com.oracle.java.Helper-Tool.plist Support
    User Launch Agents: ℹ️
      [loaded] com.google.keystone.agent.plist Support
    User Login Items: ℹ️
      None
    Internet Plug-ins: ℹ️
      Flip4Mac WMV Plugin: Version: 2.3.5.4 Support
      FlashPlayer-10.6: Version: 15.0.0.239 - SDK 10.6 Support
      JavaAppletPlugin: Version: Java 8 Update 25 Check version
      Flash Player: Version: 15.0.0.239 - SDK 10.6 Support
      QuickTime Plugin: Version: 7.7.1
      Google Earth Web Plug-in: Version: 6.1 Support
      Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
      iPhotoPhotocast: Version: 7.0
    3rd Party Preference Panes: ℹ️
      Flash Player  Support
      Flip4Mac WMV  Support
      Java  Support
      Perian  Support
      Webmailer  Support
    Time Machine: ℹ️
      Time Machine not configured!
    Top Processes by CPU: ℹ️
          3% WindowServer
          0% fontd
          0% ps
          0% opendirectoryd
    Top Processes by Memory: ℹ️
      180 MB Safari
      90 MB WebProcess
      43 MB WindowServer
      30 MB Dock
      22 MB Finder
    Virtual Memory Information: ℹ️
      2.74 GB Free RAM
      711 MB Active RAM
      192 MB Inactive RAM
      387 MB Wired RAM
      274 MB Page-ins
      0 B Page-outs

    It seems a repair permissions solved it.
    What triggered this issue in the first place was Facebook told me my certificate in the first place was not valid.    Updating to Safari 6.1.6 from 6.1.4, and adding the 10.7.5 2014 Security Update #4 followed, and then it wouldn't keep the login on reboot.   Repairing permissions finally solved it.

  • IPFW losing rules after reboot

    I am trying to block port 137 UDP and TCP and after I reboot the rules are gone. I run the following commands:
    sudo ipfw add 1 deny tcp from any to any 137 out
    sudo ipfw add 2 deny udp from any to any 137 out
    Before a reboot I run sudo ipfw list and things look great.....reboot and run it again and I just see the default rule.
    Probably a stupid question, but I can't find the answer anywhere and I am a noob with ipfw. And Leopard just mixes the whole process up as well with ipfw and its new application firewall.
    So I guess my questions are: Why do the rules disappear? How do I get the rules to stay?
    Thanks,
    Dan

    Hi
    It sounds like you need to configure a startup script without a startup script when you reboot your computer- the computer "forgets" the ipfw rules
    You can google the search terms : "ipfw startup script " "launch daemons ipfw " " ipfw rules gone after reboot" "shell script launch firewall rules ipfw" "ipfw startup plist " -OR-
    You can use WATERROOF waterroof is a free application that will help you configure your ipfw rules waterroof will also install a startup script and a startup plist on your hard drive
    Check out this link to the waterroof website
    http://www.hanynet.com/waterroof/
    Hope This Helps

  • ISCSI ASM partition losing permissions on reboot

    Using OEL 5.4. I'm trying to get my permissions to stick on a disk partition so that ASM can use the disk. Every time I reboot though I have to chown and chmod the disk so ASM can use it. Anyone have any idea how to get the permissions to stick after a reboot?

    I'm sorry I am using asmlib and I have configured the disk using the oracleasm createdisk command. With that I should be able to view the disk when I create my ASM instance, but the only way it sees it is if I chown and chmod the disk to oracle:dba. Maybe I should change the configuration to root:something and see if that works.
    Edit:
    I went back and noticed that you used /sbin/service oracleasm... I was using /etc/init.d/oracleasm. For some reason that made the difference. I now don't have to change the permissions in order for ASM to use/see the disks. I reported it on my metalink ticket maybe they will make note of it somewhere.
    Edited by: 2Luke2 on Apr 10, 2010 12:33 PM
    Edited by: 2Luke2 on Apr 10, 2010 12:35 PM

  • CAPWAP Mesh AP (MAP) Losing BGN on Reboot

    Working on getting an ethernet bridge configured and all is good, but after doing some testing I've found that if my MAP loses power, it will not connect back to the RAP and can't find the WLC.  From my understanding, even though these are LWAPP APs, they should still save the BGN somewhere on the AP in a file.  In my test scenario, I have the AP connected to a switch that is not connected back to the network the WLC or RAP is on (this way I can replicate my intended design).
    I'm just looking for some insight from someone who's "been there" with this issue.  I doubt my remote site will have a power outage, but I need to be prepared.
    Thanks in advance!

    What equipment do you have and what code. I run indoor mesh and notice the same thing, but it's code dependent for some reason.  Never seen that issue in any outdoor mesh deployments I have had. 
    -Scott

  • Catos 7.4. losing config after reload

    Hello,
    A customer is having the following problem on severals sites.
    After a reload, some cat6000-sup1a-withoutMSFC and some cat2948G all running release 7.4.3 lose some part (not all) of the configuration, after a reload.
    Sometime the vlan configuration vanished, some other time the SNMP configuration disappeared.
    Does anyone already get this kind of problem ?
    I found no bug on the bug tools or on the RN for 7.4.x.
    Regards,

    Hello Prashanth,
    On one cat6X00, the sh version from the sh tech do not show me any checksum failure, but I can find this on the "sh log" from the console port after a reload (and loosing some part of configuration):
    Console> (enable) show logg buff 1023
    2005 Aug 08 07:12:43 %SYS-4-NVLOG:check_block_and_log:Block 0 checksum failed: 0x2CCB(0x2CC9)
    2005 Aug 08 07:12:52 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 1
    2005 Aug 08 07:12:54 %SYS-1-SYS_ENABLEPS: Power supply 1 enabled
    2005 Aug 08 07:12:54 %SYS-1-SYS_ENABLEPS: Power supply 2 enabled
    2005 Aug 08 07:12:54 %SYS-5-MOD_PWRON:Module 3 powered up
    2005 Aug 08 07:12:55 %SYS-5-MOD_PWRON:Module 4 powered up
    2005 Aug 08 06:12:57 %SYS-5-MOD_OK:Module 1 is online
    2005 Aug 08 06:13:02 %DTP-5-TRUNKPORTON:Port 1/1 has become dot1q trunk
    2005 Aug 08 06:13:02 %DTP-5-TRUNKPORTON:Port 1/2 has become dot1q trunk
    2005 Aug 08 06:13:04 %ETHC-5-PORTTOSTP:Port 1/1 joined bridge port 1/1-2
    2005 Aug 08 06:13:04 %ETHC-5-PORTTOSTP:Port 1/2 joined bridge port 1/1-2
    2005 Aug 08 06:13:55 %SYS-5-MOD_OK:Module 3 is online
    2005 Aug 08 06:13:55 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 3
    2005 Aug 08 06:13:56 %SYS-5-MOD_OK:Module 4 is online
    2005 Aug 08 06:13:56 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 4
    So this cat6x00 could match this bug. Do you aggree with me ?
    Best regards,

  • Win98 forgets PCI-1200 config on reboot

    After installing NIDAQ 6.9.3 then installing my PCI-1200 card the system works great. When I power down the computer and restart, I get the error "device is not responding to the base address" when I try to run a test panel in NI-MAX. Has anyone else run into this issue and is there a solution?
    p.s. It's a Win98SE system with Labview 5.1 installed.
    Thanks.

    There are a couple of reasons that a device might fail this test.
    Some times windows is not able to set up the appropriate resources. Try switching to a different slop in the machine.
    It is possible for the device to be in an unsafe state that results in this failure as well. Open a new LabVIEW VI and place the Device Rest.vi on the diagram. Next, double click on the Device Reset.vi to open it up. Verify the device number is set to the correct value and run the VI. It should take about 5 to 10 seconds and the error status should still be 0. Now try running the Test Resources in the Properties page in MAX for the device or try running the test panel again.
    When you upgraded to 6.9.3, did you remove the previous version of NI-DAQ first? This can cause
    strange issues to come up, because it is possible to have parts of each version on the machine at one time. I would suggest uninstalling and reinstalling NI-DAQ in this case and make sure you remove the device from the computer before uninstalling and reinstall the hardware after you have performed the reinstall.
    I hope this helps out,
    Joshua

Maybe you are looking for