2602e Reset to Defaults Except IP not Work over Web GUI

Hello,
1. Set a Static IP
2. Apply & Save Configuration
3. After Reboot the IP is correct.
Then do Reset to Defaults Except IP in the WEB Gui.
After Reboot the AP loos the static IP and get a DHCP Address.
Reset to Defaults Except IP = Reset to Defaults !
Whats Wrong ?

OK, here is:
Writing out the event log to flash:/event.log ...
*Jan 22 17:44:56.675: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
*Jan 22 17:44:57.547: %SYS-5-RELOAD: Reload requested by on console. Reload Reason: Reload Command.
Write of event.log done
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 212 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 15058432
flashfs[0]: Bytes available: 16939520
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 10:f3:11:c2:2e:3a
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a"...##########################
File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Tide MB - 32MB of flash
Xmodem file system is available.
flashfs[0]: 212 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 15058432
flashfs[0]: Bytes available: 16939520
flashfs[0]: flashfs fsck took 14 seconds.
Base Ethernet MAC address: 10:f3:11:c2:2e:3a
Boot CMD: 'boot flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a;flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a'
Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a"...#######################################
File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a" uncompressed and installed, entry point: 0x1003000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 23-Dec-13 08:11 by prod_rel_team
Tide MB - 32MB of flash
Initializing flashfs...
flashfs[3]: 212 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 15058432
flashfs[3]: Bytes available: 16681472
flashfs[3]: flashfs fsck took 12 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCC
Copy in progress...CC
Copy in progress...CCCCC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/B2.bin
Radio1 present 8764 8000 0 88000000 88010000 4
POWER TABLE FILENAME = ram:/B5.bin
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602E-E-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FGL1711Z6K6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 10:F3:11:C2:2E:3A
Part Number                          : 73-14511-02
PCA Assembly Number                  : 800-37898-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17093TXF
Top Assembly Part Number             : 800-38357-01
Top Assembly Serial Number           : FGL1711Z6K6
Top Revision Number                  : A0
Product/Model Number                 : AIR-SAP2602E-E-K9
Press RETURN to get started!
*Mar 1 00:00:16.035: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:16.151: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (11)APAVC: WlanPAKs 18174 RadioPaks 17566
*Mar 1 00:00:23.131: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:29.443: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:29.503: initializing dot11 onplus
*Mar 1 00:00:29.667: not a autoconfig enabled device!!!
*Mar 1 00:00:31.671: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:32.671: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:01:18.015: Starting Ethernet promiscuous mode
*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jan 22 17:44:57.007: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Jan 22 17:44:57.015: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 23-Dec-13 08:11 by prod_rel_team
*Jan 22 17:44:57.015: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to downERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch
*Jan 22 17:45:01.667: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (0-0)
*Jan 22 17:45:01.667: DPAA Initialization Complete
*Jan 22 17:45:01.667: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Jan 22 17:45:02.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Jan 22 17:45:06.863: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.16.33.216, mask 255.255.254.0, hostname ap

Similar Messages

TH_DELETE_MODE not working in Web GUI after EHP7 upgrade

Hi
After upgrading to EHP7 the function module TH_DELETE_MODE is not working in the Web GUI. If I start the TH_DELETE_MODE in SE37 with the default paramter "1-" I'll get the HTTP error code 500. We use the function module for our webdynpro to logout but it is not working anymore.
Any idea or recommendation?
Thank you and best regards, Ronny

Your server-side include has all of the HTML on it for a full
page.
Strip everything from it except the stuff you want to
include.
http://www.fordwebs.com/mx-asp/ssi-index.asp
Ken Ford
Adobe Community Expert
Fordwebs, LLC
http://www.fordwebs.com
"ValsGalore" <[email protected]> wrote in
message news:f019c0$in1$[email protected]..
>I just recently began work on an existing Web site, which
includes the file
> nav.asp on every page. After I made some changes to one
of the pages (it's
> temporarily located at
http://www.enviroglasproducts.com/reps5.asp),
I found
> that when I closed it and reopened it in Dreamweaver, I
could no longer see the
> page in preview mode.
>
> It shows my </head> tag highlighted in yellow, but
won't let me click on it.
> In code view, the <table> tag, which is the first
tag after <body>, is "marked
> as invalid because it's an overlapping or unclosed tag."
I've been over this
> document several times, but I cannot find any errors in
the construction of the
> table.
>
> If I copy all the content into an identical page, it
will look fine in
> Dreamweaver until I close it and reopen it, and then I
will have the same
> problem.
>
> Oddly, when I remove the  from the second cell
> of the main table, then everything looks fine.
>
> Other points worth mentioning are that (until I delete
it), nav.asp shows up
> in its proper location in reps5.asp, but nothing else
does except for the image
> that appears right above it.
>
> In other pages on the site, the included nav.asp does
not show up in
> Dreamweaver at all.
>
> Can anyone think of why this is happening?
>
> Thanks!
>

Download to excel not working in web gui

Hi All,
I created a transcation for a z report and selected the radio button Easy Web Transcation and check box SAP GUI for HTML while creating the transcation since this transcation link has to be given on SRM portal .
Now when we click link on SRM portal and execute the report everything is fine but when we click the button Local File from menu , a popup comes in which we select Spreadsheet radio button and press continue , a message is displayed in status bar of explorer
load :class Query not found
and the download never complets it only shows the hourglass.
How to solve this?
Regards,
Anubhav

Hi @all
Excel Export needs an installed Java RE on the client side
I solved the problem by installing JRE 1.6.0.
Regards
Marcel
Edited by: Marcel Hündler on Feb 16, 2010 5:30 PM

Transaction codes is not working in WEB GUI URL

Hi All,
We configured Integrated ITS in ECC 6.0 it is working fine but
if i enter any Tcode in URL but it showing SAP Easy access screen only .i want run some tcode throug URL .Can you please let me know how solve this issue.
Thanks in advance
Regards,
Hari Prasad.L

Hello Hari,
Your URL should probably look something like:
http://hostname:port/sap/bc/gui/sap/its/webgui?~transaction=sm50
this would start webgui in transaction SM50.
You can add parameters to the URL with the & so:
http://hostname:port/sap/bc/gui/sap/its/webgui?~transaction=sm50&sap-client=100&sap-language=EN
this would start webgui in client 100 with language English in transaction SM50
Edgar

Drop-down box does not work with Web GUI

Situation:
On CE5 (ECC 5.)-> transaction "MM02"
-> click on drop-down for "Material"
-> see distorted pop-up
Solution:
apply kernel patch #144.
ITS is part of the Basis, starting with WebAS 6.40

You wouldn't happen to be using Vista's Home Edition are you? I work from home and have Vista Home on one of my PC's and it has the same issue when I'm connected to 2004s systems. Vista Home isn't supported. Only Vista Prof. Oddly, if I'm using the same GUI to attach to 4.6C releases, I don't have this issue.

Colors not displaying in WEB GUI

Hi,
In WEB GUI, I am unable to see the colors in my ALV Grid when the fields are in editable mode where as in SAP GUI am able to. There is no problem when the fields are in non-editable mode.
Can you help me out to view the colors in my ALV Grid for the editable fields in WEB GUI?
Thanks,
Adithya M.

You might be out of luck, because usually there are no specific settings for the WEB GUI. And one of the problems with WEB GUI is that it doesn't support all the functionality which is offered in your standard GUI. So it is possible that this is exactly one of the scenarios WEB GUI doesn't support. That is also the reason why not all SAP transaction work in WEB GUI. We had issues with parts of TEM transactions not working via WEB GUI.
Michael

Thanks for responding. Since I upgraded ITUNES to IOS 6, my IPOD Touch no longer works at all. I had numerous apps, music and videos on this touch. It made me restore to factory reset and it still does not work!!! Nothing I do will work on this touch n

Thanks for responding. Since I upgraded ITUNES to IOS 6, my IPOD Touch no longer works at all. I had numerous apps, music and videos on this touch. It made me restore to factory reset and it still does not work!!! Nothing I do will work on this touch now. I have so much data on this, I don't want to loose or have to restore!
Can you help me?
Thanks

If you restored to factory settings/new iPod and still have the problem that indicates a hardware problem.
Make an appointment at the Genius Bar of an Apple store..
Apple Retail Store - Genius Bar

I have a 4th gen iPod touch and I can not connect to the Internet even though my iPad works and my computer let's me get into the Internet. It gives me a message cannot to server. Please help I have tried to reset it but that does not work

I have a iPod touch 4th gen. And I cannot get into the Internet I get a message that say cannot connect to server. The other computer and my iPad still work with the Internet . I have reeked to reset it but that does not work. Please help me.

I do not know wat "reeked to reset" means.
Try the following:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Power off and then on your router.
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections

Default Mail app not working with yahoo mail. Won't update.

Default Maill app not working with Yahoo Mail.
It stopped working the other day. I tried everything but it wouldn't update new mail. The yahoo account itself is fine because I can see new mail on Yahoo or a yahoo app.
I tried deleting the account and putting it back on, but now it has 0 mail in any part of it. Nothing has synced.
What do I do?
iPad 2 latest OS.

A lot of people have been unable to access Yahoo e-mail on their iPhones or iPads. My wife’s iPad was not downloading Yahoo mail, although her iPhone was. Both used IOS 8.2. We tried deleting the account several times and troubleshooting all of the other settings. The problem appears to have been that allowing the IOS to automatically create the account on the iPad resulted in the wrong settings for the incoming server. The following procedure, pieced together from two websites, fixed the problem for us. So far, so good.
https://portal.smartertools.com/kb/a2659/configure-imap-for-iphone-or-ipad.aspx
https://help.yahoo.com/kb/mobile-mail/imap-server-settings-sln4075.html
On the iPhone, tap Settings.
Tap Mail, Contacts, Calendars.
Tap your Yahoo account, then delete it.
Tap Add Account.
Tap Other.
Tap Add Mail Account.
Complete the Name, Address (email address), Password and Description fields.
Click Next.
Ensure IMAP is selected.
Enter the following incoming mail server information:
Incoming Mail (IMAP) Server - Requires SSL
Server: imap.mail.yahoo.com
Port: 993
Requires SSL: Yes
Hostname is mail.yahoo.com.
Username is your full email address
Password is the same password used to access webmail.
Enter the following outgoing mail server information:
Outgoing Mail (SMTP) Server - Requires SSL
Server: smtp.mail.yahoo.com
Port: 465 or 587
Requires SSL: Yes
Requires authentication: Yes
Username is your full email address
Password is the same password used to access webmail. It may have been entered for you.
Tap Next.
The iPhone will establish an SSL connection to your IMAP and SMTP servers.
That’s all!

My Ipod is stuck in recovery mode with the plug in to itunes thing on the screen I tryed to restore it but I keep getting a error 28 and I tryed to do the reset thing but it did not work what do I do?

My Ipod is stuck in recovery mode with the plug in to itunes thing on the screen I tryed to restore it but I keep getting a error 28 and I tryed to do the reset thing but it did not work what do I do?

Hi,
You could see if this helps...
DFU Mode / Unable to Update or Restore
http://support.apple.com/kb/HT1808
DFU Mode
Open iTunes and Connect the iPod to your Mac
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time
After 10 Seconds release the Sleep/Wake Button until iTunes tells you it has Detected an iPod in Recovery Mode...
The Phone Screen will remain Black... Now Restore.
Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414

I was reset my phone n its not working??? so plz help me???

i was reset my phone n its not working??? so plz help me???

What is it not doing? You say you did a reset, what is displayed on the screen?

TS3406 Everytime is restart or update my iPhone 5s it stops making calls, i tried the air plain mode toggle & to reset thenetwork setting, it's not working !! What should i do ??

Everytime is restart or update my iPhone 5s it stops making calls, i tried the air plain mode toggle & to reset thenetwork setting, it's not working !! What should i do ??

If it has been officially unlocked, it will stay unlocked after an update:
iPhone: About unlocking

TS3474 Ipod is showing a unhappy face with the apple website for the iPod support. I have reset it but this did not work. any suggestions?

Ipod is showing a unhappy face with the apple website for the iPod support. I have reset it but this did not work. any suggestions?

See here: iPod displays a sad iPod icon
And here for more troubleshooting.
https://discussions.apple.com/message/2369954?messageID=2369954#2369954
B-rock

I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

Put in a micro SIM (SIM need not be active) and
Restore from backup
Restore as new
http://support.apple.com/en-us/HT201252

Facebook App not working over 3G, but works over Wi-Fi.

I have a BlackBerry® Curve™ 3G 9330 Social Messaging Ready smartphone. My current software version is 6.0 Bundle 2333. My Facebook application worked perfectly fine when I got the phone a few months ago over the Verizon 3G network and Wi-Fi, but when I recently updated Facebook to version 2.0.0.58, it does not work over 3G anymore. But everytime I try to connect via 3G it says "We cannot reach the Facebook server at this time. Please try again later. (100)" It does however still work over Wi-Fi.
I have tried various attempts to fix it: uninstalling the App and re-installing it and also removing the battery and putting it back in (hard reset), but nothing has worked.
Is anyone else have this same issue? Is there a way to restore my Blackberry to its factory settings so that I can just use the older version of the Facebook App [that was previously installed]?
Thank you.

Hey metalhourse90,
I can see from your PIN that you currently don't have browsing services included in your data plan. I would advise contacting your wireless provider to have this enabled.
Thanks,
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

2602e Reset to Defaults Except IP not Work over Web GUI

Similar Messages

Maybe you are looking for