2602I stand alone to LWAP conversion

Is it possible to convert AIR-SAP2602I to LWAP? I want to connect it to the WLC 5508 via flex ctonnect mode. What all are the LWAP models supported by the WLC 5508. I couldn't find these details in 5508 data sheet

Yes it is possible to convert to LAP.
Here is the procedure to convert:
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
You can check here about flexconnect feature matrix:
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html
Which AP supported by WLC depends on software version.
check thsi compatibilty matrix for support AP :
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
Hope it helps.
Regards
Dont forget to rate helpful posts

Similar Messages

Dock conversationwindow incoming conversations, without rendering stand-alone before the .Dock() call

We are busy developing a desktop application which uses the Lync 2013 client SDK. One of the features is to dock the conversation window of the Lync client into our own app. At the moment, this is working but the flow is not ideal:
The (incoming) conversation is created and the ConversationAdded event is fired
In the mean time, Lync already rendered the conversation window
The app gets the handle to the conversation window and docks it into a container
This results in a bit of "flickering" of screens, because Lync renders the conversation window, before the app is able to dock it into its' own panel.
I was wondering this behavior could be bypassed in any way.
I know from the samples of MS, when starting a conversation with a StartInstantMessagingButton you can initialize it with a ConversationContextualInfo object, which in turn has a ParentWindowHandle property. This is the behavior that would be IDEAL for our
app, but obviously this only works for outgoing IM conversations. Is there any way to tell Lync that all new conversations must dock?
Another possibility is to tell Lync the spot where all new conversationwindows must spawn. Is this possible?
Does anyone have done this some other way maybe?
One last thing, Our app is already visible before the conversation window, so spawning our app on top (or exactly behind) the conversation window is not possible.
Thanks

Unfortunately no, the UI does not wait for the SDK to proceed with it's functionality. The best you can do is dock as soon as you can, but as you found it will create a stand alone window briefly before you have the opportunity to dock.

Recording Stand-alone Soft Synths & Virtual Instruments in Audition 3

Hi People,
Have a little problem which I'm struggling to figure out.
I have been using Cool Edit Pro for several years. My set up has always enabled me to record any standalone Software Synths via my sound card. I have always had it set up so my sound card plays through patch one and records through another patch enabling me to record in the multi track editor with no problems at all and my set up records only the soft synth/instrument, and not any waves previously recoded. Instead just plays them back so I can build up my music and play along at any given time. Although this is a rather different approach to doing things, it suites me down to the ground and I'm happy to create this way
My problem has come upon whilst trying out the new Adobe Audition 3, which is based around ASIO Drivers. Because of this I can no longer run another program (Stand alone soft synth), because Adobe hogs the ASIO driver and will not allow another program to be run at the same time. I can use the Adobe windows driver for audition no problems and I am able to continue recording how I did with Cool Edit, but I would much prefer to go along with auditions ASIO drivers to make sure I am recording with the best quality and reliability.
My Sound card is an E-MU 1616 with breakout box. I have tried numerous ways with the patch mixer to get around this, for example I have tried using my sound cards driver for audition and ASIO4ALL2 for my soft synths. One of which is Hypersonic 2, and the other being SampleTank. I cannot for the life of me get my set up and running how it was with cool edit.
I must admit that although I have played around with my settings, it could be something simple I need to do that just hasn't jumped out at me yet. My evaluation of Audition 3 runs out in 20 days and I'm almost sure that there is a way to enable my set up to work how I want it to before I can go out and buy Audition 3. I'm very comfortable with audition 3, naturally. I love the changes and extra features it has now along from the cool edit days.
I have looked into other solutions as well after scouring message boards, one of which was Cycling 74 Soundflower, this sounded like it could be an answer but unfortunately it is Mac only. If Adobe did Audition for Mac then I wouldn't hesitate in going down that route...
My other solution is to have a second computer, either a modified mid range P C, or even a Mac, to act as my synth station and have my various software synths and such running on there and playing out to my recording PC with Audition on. This would free up the ASIO to be used by Audition solely. It's a long way around but wouldn't cost the earth and would be a simple enough idea to set up. But surly, I shouldn't need to go this far out to get my ideal setup.
Anyhow, I would much appreciate any advice and ideas to help me solve this problem; I will keep working at it in the mean time.
Hope my explanation makes sense above, I can appreciate that there are other ways like just going along with another program and such, but in all honesty I like the way I work and don't really want to move on, I'm more bothered about just getting on and recording new ideas in the environment I'm so use to. I love the way Cool Edit/Audition works for me and I have developed my own methods with the software over the years. Working with just audio suits me to the ground as I record and chop up my own Guitar bass and drums, along with sounds from my field recorder and a host of other methods and ideas.
Thanks in advance

Hi!
As long as your softsynths comes in the VSTi format (most of them do now), you can insert it on a track in Audition, which has 'host' capabilities from V3.
In the Multitrack, insert a new MIDI track from the 'Insert' menu (note: MIDI Track, not just 'MIDI').
On that track pane hit the 'Sequencer' button, and it will open in a separate window. In the pane left of the keyboard you can insert your VSTi of choice, and make your MIDI connections.
Back on the Main track pane, engage the 'L' button for Live monitoring. Actual recording (of MIDI) is done in the Sequencer window.
The usual, and recommended workflow is to keep the MIDI tracks 'open', i.e. you can edit the sound in your instrument and even the notes played at any time in the process, compiling the actual audio as the last step in the mixing.
If you kind of 'insist' on doing it the old way, you can export the audio from your recorded MIDI+VSTi creations track by track like this: Leave the Sequencer window open, make a selection in the multitrack that covers the time span you have played. Solo the track (will mute all others), and use File / Export Audio Mixdown. Use 'Master' as the source. This will give you a wave rendering of what's currently in the MIDI sequencer. Qualitywise this is better since it's all internal and digital instead of in/out of soundcards with DA/AD conversion etc.
I haven't found a method for a 'live' wave recording while you play, but there may be one...
If you purchase Audition it comes with Help files explaining this in more/better detail. ;)

Error while starting stand alone applicaitons in Web Center Content

Hi All,
I am getting this error while starting any standalone component in Oracle WebCenter Content Server :
WARNING: Jps platform factory creation failed. Reason: {0}.
java.security.PrivilegedActionException: oracle.security.jps.JpsException: JPS-0
*0065: Jps platform factory creation failed. Reason: java.lang.ClassNotFoundExcep*
tion: oracle.security.jps.tomcat.JpsTomcatPlatformFactory.
at java.security.AccessController.doPrivileged(Native Method)
at oracle.security.jps.ee.JpsPlatformFactory.getPlatformFactory(JpsPlatf
ormFactory.java:185)
at oracle.security.jps.ee.JpsPlatformFactory.getPlatformFactory(JpsPlatf
ormFactory.java:146)
at oracle.security.jps.internal.audit.AuditServiceImpl.initAuditor(Audit
ServiceImpl.java:319)
at oracle.security.jps.internal.audit.AuditServiceImpl.getAuditor(AuditS
erviceImpl.java:238)
at oracle.security.jps.internal.audit.AuditServiceImpl.getAuditor(AuditS
erviceImpl.java:373)
at oracle.security.jps.util.AuthZAuditUtil$3.run(AuthZAuditUtil.java:183
at oracle.security.jps.util.AuthZAuditUtil$3.run(AuthZAuditUtil.java:181
at java.security.AccessController.doPrivileged(Native Method)
at oracle.security.jps.util.AuthZAuditUtil.initAuditor(AuthZAuditUtil.ja
va:181)
at oracle.security.jps.util.AuthZAuditUtil.isEventLoggable(AuthZAuditUti
l.java:136)
at oracle.security.jps.util.AuthZAuditUtil.auditAuthZ(AuthZAuditUtil.jav
a:427)
at oracle.security.jps.util.JpsAuth.checkPermission(JpsAuth.java:554)
at oracle.security.jps.internal.credstore.util.CsfUtil.checkPermission(C
sfUtil.java:643)
at oracle.security.jps.internal.credstore.ssp.SspCredentialStore.getCred
entialMap(SspCredentialStore.java:497)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at idc.conversion.jps.CSFKeyLoaderAction.run(CSFKeyLoaderAction.java:56)
at java.security.AccessController.doPrivileged(Native Method)
at idc.conversion.jps.CSFKeyLoader.readKeys(CSFKeyLoader.java:166)
at intradoc.conversion.StandardKeyLoader.load(StandardKeyLoader.java:61)
at intradoc.conversion.SecurityObjects.loadKeys(SecurityObjects.java:528
at intradoc.conversion.SecurityObjects.init(SecurityObjects.java:133)
at intradoc.conversion.CryptoPasswordUtils.initSecurityObjects(CryptoPas
swordUtils.java:75)
at intradoc.conversion.CryptoPasswordUtils.loadPasswordManagement(Crypto
PasswordUtils.java:136)
at intradoc.server.IdcSystemLoader.managePasswords(IdcSystemLoader.java:
*3118)*
at intradoc.server.IdcSystemLoader.finishInit(IdcSystemLoader.java:396)
at intradoc.server.IdcSystemLoader.init(IdcSystemLoader.java:335)
at intradoc.server.IdcServerManager.init(IdcServerManager.java:120)
at intradoc.apputilities.idcshell.InteractiveShellStartup.init(Interacti
veShellStartup.java:253)
at intradoc.apputilities.idcshell.InteractiveShellStartup.startup(Intera
ctiveShellStartup.java:52)
at IdcShell.main(IdcShell.java:27)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at intradoc.loader.IdcClassLoader.invokeMain(IdcClassLoader.java:352)
at intradoc.loader.IdcClassLoader.startMain(IdcClassLoader.java:170)
at intradoc.loader.IdcClassLoader.main(IdcClassLoader.java:140)
Caused by: oracle.security.jps.JpsException: JPS-00065: Jps platform factory cre
ation failed. Reason: java.lang.ClassNotFoundException: oracle.security.jps.tomc
at.JpsTomcatPlatformFactory.
at oracle.security.jps.ee.JpsPlatformFactory$2.run(JpsPlatformFactory.ja
va:193)
at oracle.security.jps.ee.JpsPlatformFactory$2.run(JpsPlatformFactory.ja
va:186)
*... 41 more*
Mar 7, 2013 2:55:58 PM oracle.security.jps.internal.audit.AuditServiceImpl initA
uditor
WARNING: Failed to get server log directory. Reason: oracle.security.jps.JpsExce
ption: JPS-00065: Jps platform factory creation failed. Reason: oracle.security.
jps.JpsException: JPS-00065: Jps platform factory creation failed. Reason: java.
lang.ClassNotFoundException: oracle.security.jps.tomcat.JpsTomcatPlatformFactory
intradoc.common.ServiceException:
at intradoc.server.IdcServerManager.init(IdcServerManager.java:230)
at intradoc.apputilities.idcshell.InteractiveShellStartup.init(Interacti
veShellStartup.java:253)
at intradoc.apputilities.idcshell.InteractiveShellStartup.startup(Intera
ctiveShellStartup.java:52)
at IdcShell.main(IdcShell.java:27)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at intradoc.loader.IdcClassLoader.invokeMain(IdcClassLoader.java:352)
at intradoc.loader.IdcClassLoader.startMain(IdcClassLoader.java:170)
at intradoc.loader.IdcClassLoader.main(IdcClassLoader.java:140)
Caused by: intradoc.data.DataException: !apErrorWithTable,DocMetaDefinition
at intradoc.shared.MetaFieldData.initIndexes(MetaFieldData.java:171)
at intradoc.shared.MetaFieldData.init(MetaFieldData.java:84)
at intradoc.server.subject.MetaDataSubjectCallback.cacheMetaData(MetaDat
aSubjectCallback.java:42)
at intradoc.server.subject.MetaDataSubjectCallback.refresh(MetaDataSubje
ctCallback.java:35)
at intradoc.server.IdcSystemLoader.loadCachedTables(IdcSystemLoader.java
*:1255)*
at intradoc.server.IdcSystemLoader.loadCaches(IdcSystemLoader.java:1164)
at intradoc.server.IdcServerManager.init(IdcServerManager.java:132)
*... 10 more*
Caused by: intradoc.data.DataException: !syColumnDoesNotExist,dDecimalScale
at intradoc.data.ResultSetUtils.getIndexMustExist(ResultSetUtils.java:44
*7)*
at intradoc.shared.MetaFieldData.initIndexes(MetaFieldData.java:167)
*... 16 more*
Error with table 'DocMetaDefinition'.
The column 'dDecimalScale' does not exist in this table.
I am using 11.1.1.6 free version of webcenter content and using appropriate database with required tables created by RCU of appropriate version and also using required weblogic server.
Is there anything like , we are not allowed to use stand alone application in free version ? or problem is something else.
Thank you in advance.
Edited by: 957580 on Mar 7, 2013 2:01 AM

Hi Deepak,
Thanks for Reply.
But in /home/sapcs/conf/http.conf file its already maintained like this, sending you some part of httpd.conf file
Listen: Allows you to bind Apache to specific IP addresses and/or # ports, instead of the default. See also the #<VirtualHost> # directive.
Change this to Listen on specific IP addresses as shown below to prevent Apache from glomming onto all bound IP #addresses.
Listen 1090
User/Group: The name (or #number) of the user/group to run httpd as.
It is usually good practice to create a dedicated user and group for
running httpd, as with most system services.
User sapcs
Group sapsys
</IfModule>
</IfModule>
even after restarting server i am getting same problem
[sapcs@hpsebdev1 bin]$ apachectl start
(13)Permission denied: make_sock: could not bind to address [::]:80
(13)Permission denied: make_sock: could not bind to address 0.0.0.0:80
no listening sockets available, shutting down
Unable to open logs
I am using a non root user to start apachectl command
Regards
Gagan Sharma

Can AIR-CAP1602i-x-k9 be converted to stand alone??

can air-cap1602i-x-k9 be converted to stand alone??

Yes , you can convert the AP to stanadlone by pushig the below image into the AP
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB3a&relind=AVAILABLE&rellifecycle=ED&reltype=latest
You can use the below method to convert the same
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release
using a TFTP server: This method is for local conversion.
Step 1 The PC on which your TFTP server software runs must be configured with a static IP address in the range
of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a
1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200
series access point.
Step 4 Connect the PC to the access point using a Category 5 or better Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the
MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED
blinking green.
Thanks..

Compressor as Stand Alone Product

Can you use Apple Compressor as a stand alone product without purchasing Final Cut Pro X?
I would like to use it to convert MTS files to a useable format for iMovie and Final Cut Pro Express.
Thanks.

To add to Russ. I second that you would most likely have to buy clipwrap ino order to get them to a quicktime format that compressor could see. But ClipWrap will also do conversions for you. I know it will let me convert to pro-res but if you don't have a version of FCP that might not be availble but it does have Apple Intermidiate Codec which works just fine in iMovie and Final Cut Express. So to answer your question, yes it works as a stand alone app and great at doing its thing as long as quicktime can play the file your trying to convert. But for the type of files you want to convert you need to use ClipWrap and since it will do the converson for you, you don't have to have Compressor. Now Compressor will give you more control of your final output but start with ClipWrap see if it get the job done for you. If your happy great! If you need more control then purchace Compressor.

SSH issue when converting stand alone to RAC -- manually

Hi All,
I face an issue with SSH when trying to convert a stand alone database to RAC (2 node). I am trying the manual way.
Plan:
Migrate the filesystem to ASM
Install the cluster
Create another ASM instance on node 2
Create another DB instance on node 2
Register the new ASM and DB instance with cluster manually
I have successfully completed the filesystem conversion to ASM.
When performing the pre requisites for cluster installation, i am facing problem when configuring the SSH.
Node 1 -- Has the existing stand alone database
Unable to do SSH from node 1 to node 1 (self) or from node 2 to node 1.
However i am able to SSH from node 2 to node 1 and node 2 to node 2 (self)
Steps which i tried already:
1)Created another user(test) on both the nodes and try to establish SSH to see if configuration problem is with this current user (RAC1). SSH configured successfully with user test
2)Copied the profile of RAC 1 user on node 2 to node 1 and retried the SSH configuration. But it failed
3)Dropped the user RAC1 on node 1, deleted all the hidden files in home directory so that they can be created freshly when the user (RAC1) is recreated. Tried SSH configuration again and it failed
Can you please help me to fix this issue and identify the root cause of this.
Please let me know if you have any questions.

user 777111 wrote:
I face an issue with SSH when trying to convert a stand alone database to RAC (2 node). I am trying the manual way.What operating system?
To create automated ssh connectivity between 2 accounts (same platform, or different platforms, does not matter):
1. generate a ssh key for the current account (command: <i>ssh-keygen -t rsa</i>)
2. create the file +$HOME/.ssh/authorized_keys+ and copy all the RSA public keys from all accounts that are trusted (this includes the current account's public key) - public key file is +$HOME/.ssh/id_rdsa.pub+
3. manually test connectivity from the trusted account to the other accounts - as the signatures of those servers need to be accepted and stored in +$HOME/.ssh/known_hosts+
When setting this up for RAC, you first need to generate the RSA keys and then do the above on one node. Create +$HOME/.ssh/authorized_keys+ containing all RSA public keys. Build +$HOME/.ssh/known_hosts+ by ssh'ing from that node to the other nodes (do not need a successful logon - only need to accept servers signatures).
When done, copy both these files to the +$HOME/.ssh+ directory on all other RAC nodes.

Can't install Lightroom 5 on a second computer, I am NOT a creative cloud customer, I am a stand-alone user. How do I enter my serial number???

I can't install Lightroom 5 on a second computer, I am NOT a creative cloud customer, I am a stand-alone user. But when I try to install on my laptop, it always trys to sell me the monthly membership. How do I enter my serial number in the second copy of lightroom? It won't ask me for it, and I cannot enter it anywhere in the settings? I am stuck

You probably downloaded the Cloud version. Get the licensed version thru the following linked page...
Lightroom - all versions
Windows
http://www.adobe.com/support/downloads/product.jsp?product=113&platform=Windows
Mac
http://www.adobe.com/support/downloads/product.jsp?product=113&platform=Macintosh

Migrating stand alone programs to web based application

Hi,
I have a small application consisting of .class files. I created these using Swing components and it's based on Client/ server model where it accesses Oracle Database.
I want to deploy these programs in Java App Server so that it can be accessed thru web browser.
Please tell me how to do it.
Thanks in advance.
Rajeev.
Message was edited by:
Rajeev.Asthana

If this was the thing, Sun, Microsoft and IBM
wouldn't have even giving a thought of migrating
legacy application (I'm talking about Mainframes and
AS/400 here). If this kind of migration is possible,
can't we migrate a java code from stand-alone
"version" to web enabled.
Migration is not really a term to use to for converting a stand alone application to a web application. Unless of course again you are prepared to turn it into an applet.
The flow and control of a web application are entirely different from a stand alone app. You will not be able to reuse Swing GUI's from a web server. I don't know how to make that any clearer.
Hopefully you have a good design for your existing application and you can relatively easily reuse your existing business logic components.

Need help in creating a web application that runs on a stand alone sys.

I am planning a small java web application complete with database. I need to know if there are any ways to deploy that application on a stand alone system and that if there is any way to make an executable for that application so that the user need not go through the process of deploying the app and starting the server whenever he restarts the system. Can anyone help me in this regard? Thanks in advance.

Hi Alex,
Since I had a Gmail test servlet kicking around, I ran it on the latest V3 nightly build.
On the first run, I encountered the following nested exceptions:
javax.mail.MessagingException: Could not connect to SMTP host: smtp.gmail.com, port: 465
--> java.net.SocketException: java.security.NoSuchAlgorithmException: Error constructing implementation (algorithm: Default, provider: SunJSSE, class: com.sun.net.ssl.internal.ssl.DefaultSSLContextImpl)
--> java.security.NoSuchAlgorithmException: Error constructing implementation (algorithm: Default, provider: SunJSSE, class: com.sun.net.ssl.internal.ssl.DefaultSSLContextImpl)
--> java.security.UnrecoverableKeyException: Password must not be nullThe UnrecoverableKeyException is a manifestation of [https://glassfish.dev.java.net/issues/show_bug.cgi?id=6938|https://glassfish.dev.java.net/issues/show_bug.cgi?id=6938]
I worked around this by adding the following JVM config options to domain.xml
<jvm-options>-Djavax.net.ssl.keyStorePassword=changeit</jvm-options>
<jvm-options>-Djavax.net.ssl.trustStorePassword=changeit</jvm-options> (Note: the default master password is "changeit")
These lines are placed in /domain/configs/config/java-config of domain.xml for the particular server config you're using. There's only one server config in the default domain.xml shipped with V3. Then restart the server.
I retested the code on both port 465 and 587, with and without the above config changes. Without the change, they both fail the same way, and with the change, they both work. Let me know if this helps.
-Peter

SAP PI Installation on Stand alone machine

Hi,
Thanks to one and all for having such a nice forum as it has answer to all the questions which I have posted.
I have been given a very interesting work for anlying if SAP PI could be installed on a standalone machine without having any SAP box. My requirement is to install SAP PI tool for non SAP integration.
I will distribute my question in 2 parts
1. Can I install SAP PI in a stand alone desktop?
2. Is is important to have a SAP R/3 system to install SAP PI tool?
Please do share your thoughts and if possible please share the document which could be used as proof.
Thanks in advance.
Gautam

1. Can I install SAP PI in a stand alone desktop?
Yes.
2. Is is important to have a SAP R/3 system to install SAP PI tool?
No.
If you are trying to install 7.1 then have a look at the video blog (easily available on SDN) for the same....will help you.
Regards,
Abhishek.

Download LR 5.5 as stand-alone

Hi,
I am using LIghroom 5.4 and have heard about the updated version 5.5 which I would like to download and install as it worked fine since I started using LR as from version 3.
I want to use it as a stand-alone program and have no interest to join the Adobe cloud.
How and from where can I download the latest update without installing the cloud desktop software?
Update:
found the solution myself:
I went to the download page , pressed on the the windows version of LR 5.5 (german in my case). This opened up a text page with links. Here you scroll down (press page down couple of times) until you see Downloads, and here you press "Proceed to download" which will download the 920 MB exe file on the local harddrive.
I got frustrated because I missed that I had to scroll down so far, so all I ended up a couple of times was the cloud installer.
For amateurs this is not the way how I will continue. I will stick to LR as long as it is offered as a stand-alone program. I am not willing to go into the cloud and make it a cash cow for adobe....
best regards,
Matthias Brand

You don't need to be attached to the cloud constantly for the newer versions to work. They only have to connect once every four months or so. I believe they also offer enterprise/government versions that don't require a connection at all, but you would have to contact Adobe sales to find out about that. Also, you can pay in yearly increments instead of monthly (and there may be more options for government versions).
The only perpetual licenses you can get are for CS6 and equivalent versions, but nothing newer.

Using a Mac Mini Server as a traditional stand alone desktop

Hello all, currently I have a late 2008 model 17" MacBook pro, Time Capsule, Apple TV and an Iphone 3GS and Ipod Traditional. I would like to add a desktop system to coordinate all of these items, to be the centerpiece is you will, in my home. I'm interested in buying a mac mini, I began to do research however and saw the Mac Mini Server which has greater memory capacity 4GB vs 2GB RAM, and dual 500Gb vs the standard Mac Mini which has one at 320GB. I would like to take advantage of these upgrades as I'm a writer and will be constantly on the web for work as well as likely keep a lot of items on the hard drive.
However I noticed the Mac Mini server utilizes Mac OSX snow leopard SERVER as opposed to the user grade Mac OSX. *My question is if the Mac Mini Server with MAC OSX server can still be used as a stand alone desktop, connecting it to a spare LCD television I have and a mac wireless keyboard/mouse?*
I'm aware that unlike the other mac mini and imacs it does not come with ilife and other pre-installed software, and *I want to know if it's still possible to purchase after market and install said software utilizing them in the traditional manor?*
Thank you in advance for any feedback you can provide and I apologize if my question was difficult to comprehend due to my lack of computer knowledge. I also apologize if this question is similar to others you've received lately as I did a quick scan of google and these forums and did not seem to find the specific answer I was looking for.

Welcome to the Apple Discussions!
Let me clear up a misperception that you have. Both the Mac mini and the Mac mini Server have a capacity to address 8 GB of RAM. There are two SO-DIMM slots in each model. The mac mini comes preconfigured by Apple with 2 GB of RAM (2 x 1 GB). The mini Server comes preconfigured with 4 GB of RAM (2 x 2 GB). You can buy and install yourself up to 8 GB of RAM (2 x 4 GB).
You can even install Mac OS X Snow Leopard client, which will meet your needs a bit better than Server, now that folks have figured out how to do it;
http://discussions.apple.com/thread.jspa?threadID=2539663&tstart=0
And yes you can buy and install iLife, and pretty much everything else that you want to include in your kit. Either model of mini works fine with wireless keyboards and mouses. If your LCD TV has an HDMI port, then a simple HDMI to HDMI cable would be the simplest manner to connect it to the mini.
Dah•veed

HT201485 My iphone won't let me download apps and refers me to my computer for verification. My computer will not access itunes due network issue. How to make iphone stand alone for downloads & updates.

In iTunes my iPhone refers me to iTunes on my computer for verification. iTunes won't work on my computer. How can both my iPhone and iPad stand alone?

Turns out that when my iPod Touch was restored, the restrictions had been turned ON for Facebook and several other apps. This is what was preventing the Facebook app from accessing my Camera Roll for picture downloads. This is odd since all of my iPod backups would not have had those settings turned on. This is also the first time this has occurred given the few times I've had to restore my iPod Touch.
Anyway if you experience the same behavior from your iPod or iPhone with iOS 8.0.2, just go to the General settings and review your settings under Restrictions. Once you set them to allow for changes, you should be back in business.

Ive uploaded firefox 4 and now I cant access messenger from the browser, it say unavailable, but it works as a stand alone prog.. cant find a setting to reactivate.. Please advise TY!

Im on Win 7 Ultimate and had Firefox working fine with messenger in the browser & could use the pop up chat box. Since the upload I get the message that messenger is currently not available, but it works fine when I activate it as a stand alone prog. but I want it back in my browser.. cant find any setting or pref. to activate it... have cleared cache and history, restarted, even reloaded a messenger from Windows essencials.. no difference.. it been like this for 5 days since the update.. anyone got a solution? thanks alot for your help.

DFU mode:
http://www.iclarified.com/entry/index.php?enid=1034

2602I stand alone to LWAP conversion

Similar Messages

Maybe you are looking for