2610 Factory Reset and Startup Config Files

Hi all;
I have a used 2610 which I did a factory reset on. I am able to get into the IOS and edit/change the config.
However after editing and trying to save using the command:
copy run start
I get prompted to save the config to a file name/location which ultimately fails. Then on reboot it goes into the "basic setup" sequence again never saving to the config I'm trying to save.
The IOS ver. is 12.0(3)T and I do have the latest ver. and an TFTP program to upgrade, but I would like to create a config and save it first.
Any help would be appreciated.
Thanks in advance. Steve

Edison;
Thanks for the reply. Yes my register was 0x2142 but I did the "config-register 0x2102" and then was able to copy the running config to the startup config.
I do have another ?. I did type in a time offset command for my timezone but after reboot it keeps defaulting back to year 1993.
Here's my sh ver:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 22-Feb-99 20:00 by ccai
Image text-base: 0x80008088, data-base: 0x8069353C
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
uptime is 14 minutes
System restarted by reload
System image file is "flash:c2600-i-mz.120-3.T"
cisco 2610 (MPC860) processor (revision 0x202) with 18432K/6144K bytes of memory
Processor board ID JAB03090910 (856765012)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Thanks, Steve

Similar Messages

  • Copying startup-config file

    Hi,
    I have one armed mode CSS11503. I can't sync. both Load balancers.
    Is it possible to copt master's startup-config file via ftp and modify than paste in slave one?

    you can copy the config from one css to a ftp server.
    First create an FTP record in config.
    Then use the command 'copy startup-config ftp '
    Edit the file and adjust circuit ip addresses and app settings.
    Then copy it into the standby CSS with the command
    copy ftp startup-config
    Gilles.

  • Help: startup-config file open failed (Not enough space)

    Who can help me ? I've an uc500 and he stil running. Now i want to change something and want to save the configuration first. But the following message appears : startup-config file open failed (Not enough space)
    this is the output from a dir flash:
    Directory of nvram:/
      227  -rw-       25897                    <no date>  startup-config
      228  ----        1933                    <no date>  private-config
      229  -rw-       25897                    <no date>  underlying-config
        1  ----          83                    <no date>  persistent-data
        2  -rw-           0                    <no date>  ifIndex-table
        3  -rw-         577                    <no date>  IOS-Self-Sig#1.cer
        4  -rw-         615                    <no date>  IOS-Self-Sig#2.cer
        5  -rw-         660                    <no date>  vlan.dat
        6  -rw-         107                    <no date>  cca.xml
        7  -rw-         586                    <no date>  IOS-Self-Sig#3.cer
    262144 bytes total (227094 bytes free)

    OK.
    Try this:
    conf t
    service compress-config
    And see if that helps. 
    If not, see if you can tftp the running config off the router and TFTP it back to startup-config:
    copy run tftp
    copy tftp start
    Then you can try a reload and see if it is cured.
    I googled and found a few cases where alot of ACLs or NAT rules could cause MALOC errors (you would see those in your logs) when implemented and could manifest itself in this condition, which could be cured after the next reload, which is why I suggested that.
    Of course, dont be remote when you do this and only do it during a maintenance window.
    Steve

  • IPad 2 factory reset and backup recover issue.p

    I had to perform a factory reset and recover on my iPad 2. iTunes only found a backup file from April of 2014. However I backup my iPad every month. I really need to recover my notes, contacts and pictures Without losing my current updates. I found a more recent backup on an external drive but iTunes overwrote it when I followed the self help instructions.  Also there are 4 Apple products being backed up on my PC and I do not know how to tell them apart. Has anyone ever had this issue and know of a valid resolutions?   Any assistance would be greatly appreciate.
    Thank you!

    Hi Since ios 7 when you charge your iPhone or iPad it Automatically backs up To icloud you can do almost everything over your WiFi. So you should have a recent backup. Cheers Brian

  • ACE Startup-config file location

    Hello,
    I was reading the ACE docs and it sounds like the startup-config file should be listed under disk0: but I don't see it there. Can someone point out where the startup-config file is.
    Thanks
    Mike

    Hi MICHAEL,
    Upon startup, the ACE loads the startup-configuration file stored in Flash memory (nonvolatile memory) to the running-configuration file stored in RAM (volatile memory). When you partition your ACE into multiple contexts, each context contains its own startup-configuration file.
    Flash memory stores the startup-configuration files for each existing context. When you create a new context, the ACE creates a new context directory in Flash memory to store the context-specific startup-configuration files. When you copy a configuration file from the ACE, you create a copy of the configuration information of the context from where you executed the command.
    To display the directory contents of a specified file system, use the dir command in Exec mode. This command displays a detailed list of directories and files contained within the specified file system on the ACE, including names, sizes, and time created. You may optionally specify the name of a directory to list.
    The syntax for this command is:
    dir {core: | disk0:[directory/][filename] | image:[filename] | probe:[filename] | volatile:[filename]}
    The keywords and arguments are:
    •core:-Displays the contents of the core: file system.
    •disk0:-Displays the contents of the disk0: file system.
    •image:-Displays the contents of the image: file system.
    •probe:-Displays the contents of the probe: file system. This directory contains the Cisco-supplied scripts. For more information about these scripts, see the Cisco 4700 Series Application Control Engine Appliance Server Load-Balancing Configuration Guide.
    •volatile:-Displays the contents of the volatile: file system.
    •directory/-(Optional) Contents of the specified directory.
    •filename-(Optional) Information that relates to the specified file, such as the file size and the date it was created. You can use wildcards in the filename. A wildcard character (*) matches all patterns. Strings after a wildcard are ignored.
    For example, to list the files in the disk0: file system, enter:
    host1/Admin# dir disk0:
    host/Admin# dir disk0:
    7465 Jan 03 00:13:22 2007 C2_dsb
    2218 Mar 07 18:38:03 2007 ECHO_PROBE_SCRIPT4
    1024 Feb 16 12:47:24 2007 core_copies_dsb/
    1024 Jan 01 00:02:07 2007 cv/
    1024 Mar 13 13:53:08 2007 dsb_dir/
    12 Jan 30 17:54:26 2007 messages
    7843 Mar 09 22:19:56 2007 running-config
    4320 Jan 05 14:37:52 2007 startup-config
    1024 Jan 01 00:02:28 2007 www/
    Usage for disk0: filesystem
    4254720 bytes total used
    6909952 bytes free
    For example, to list the core dump files in Flash memory, enter:
    host1/Admin# dir core:
    253151 Mar 14 21:23:33 2007 0x401_vsh_log.8249.tar.gz
    262711 Mar 15 21:22:18 2007 0x401_vsh_log.15592.tar.gz
    250037 Mar 15 18:35:27 2007 0x401_vsh_log.16296.tar.gz
    Usage for core: filesystem
    1847296 bytes total used
    64142336 bytes free
    65989632 bytes available

  • Thanks for responding.  Since I upgraded ITUNES to IOS 6, my IPOD Touch no longer works at all.  I had numerous apps, music and videos on this touch.  It made me restore to factory reset and it still does not work!!! Nothing I do will work on this touch n

    Thanks for responding. Since I upgraded ITUNES to IOS 6, my IPOD Touch no longer works at all. I had numerous apps, music and videos on this touch. It made me restore to factory reset and it still does not work!!! Nothing I do will work on this touch now. I have so much data on this, I don't want to loose or have to restore!
    Can you help me?
    Thanks

    If you restored to factory settings/new iPod and still have the problem that indicates a hardware problem.
    Make an appointment at the Genius Bar of an Apple store..
    Apple Retail Store - Genius Bar

  • My husband used my icloud, apple ID info on his iphone 5. we have tried deleting with no luck. Ive done a factory reset and still it won't delete his email as icloud on my phone now.

    We accidently set up my icloud email and apple id on my husbands new ihpne 5. Now on my Iphone 5 I can't get rid of it. I have deleted the account - nothing. I have done a complete factory reset and nothing!
    Everytime I access my email it states my apple id and icloud settings are incorrect. HELP!

    HI,
    It may pay to bookmark this page.
    http://www.apple.com/support/systemstatus/
    8:40 PM      Wednesday; April 10, 2013
      iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.3)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • HT5622 hi. i bought iphone 5 witch was locked, i made factory reset and now phone asking apple ID and pasword witch i dont know. i was writing to seller but he is not answering me. how to set new account for my iphone 5 what i could use it?

    hi. i bought iphone 5 witch was locked, i made factory reset and now phone asking apple ID and pasword witch i dont know. i was writing to seller but he is not answering me. how to set new account for my iphone 5 what i could use it?

    The iPhone has a feature called "Activation Lock" described here:
    http://support.apple.com/kb/PH13695
    Without that Apple ID, you will not be able to use that iPhone.

  • Why do we need to specify Role baseprovider and membership provider in Central Admin and security config files?

    Hi,
    why do we need to specify role base provider and membership provider files in central admin and securiy config files.
    thanks,
    gaurav

    We use 3 settings in Forms based auth:
    1 Membership = This contains Users and groups information. (This table also has username and password)
    2 ConnectionString = Connetion details to connect to database is stored here(servername, databasename, username, password, port )
    3 Role = This table contains all the Roles (Admin, contibutor, etc of the data source)

  • Location of MTA and POA config files:

    Hello. I'm reading an article from cool tools by Kiril Stankov regarding
    moving a groupwise database to a new volume or server. In step 4 he says
    if you are moving data between servers make sure to copy the POA, MTA,
    WAA and GWIA config files. The only one I can find is the gwia.cfg. I
    looked under SYS:\system for the others and can't find them anywhere.
    Thanks

    > What's in grpwise.ncf ?
    >
    > It should be something like
    >
    > LOAD SYS:\SYSTEM\GWPOA @POA.POA
    > LOAD SYS:\SYSTEM\GWMTA @MTA.MTA
    LOAD SYS:\SYSTEM\GWPOA @CTCPO.POA
    LOAD SYS:\SYSTEM\GWMTA @CTCMAIL.MTA
    > the files you want are the ones after the @ sign, and they should be in
    > the directory referred to in the load bit, in this case sys:\system
    Ok. So I can, in my case anyway, just copy my SYS directory over if I
    choose too
    > Cheers Dave
    >
    >
    > --
    > Dave Parkes [NSCS]
    > Occasionally resident at http://support-forums.novell.com/

  • My Droid 2 has been malfunctioning lately making the phone completely uncontrollable. I have done a hard factory reset and the problem still persists. What else can i try?

    My Droid 2 has been malfunctioning lately making the phone completely uncontrollable. I have done a hard factory reset and the problem still persists. What else can i try?

        We want you to enjoy the best reliability with your Droid 2 Jaxie! What specific problems are you having with the device? Is your software up to date? The latest version available is: 4.5.621.A955.Verizon.en.US. If the software is up to date, we recommend running the device in safe mode to determine if third party apps may be causing the issues. I hope this information is helpful.
    http://bit.ly/IPw5jE
    http://bit.ly/o5McAQ
    Sincerely,
    JonathanK_VZW
    VZW Support
    Follow Us on Twitter@VZWSupport

  • Nokia Asha 501 Factory reset and keyboard bug

    When you do a factory reset and restore the phone to the last back up point, your app store and xpress browser stops working. I have tried accessing the internet via wifi and not the mobile internet.
    You just do the factory reset and download an app or surf internet on xpress browser, it works perfectly fine. However once you do the restore it stops working. You can surf internet using Opera mini, that means wifi internet is working fine on the phone.
    Error on app store: 'Downloading Failed'.
    Error on xpress browser: 'can't load this page at the moment. Please try again later'.
    Keyboard Bug:
    when typing in portrait mode, keys on extreme right side (P,L,backspace and enter) are less resposive to touch. Same is the case of the keys on the extreme left side (Q,A,Caps and symbol). I have to keep on touching in order to make it work.
    Nokia team, please find a solution to this asap. My phone is not even one month old. This is really diappointing.
    Let me know if you need more details.

    About the backup and restore thing, i don't know why Nokia decides to cut out the good features. The backup and restore system in older S40/Asha phones worked better as users were allowed to select what is backuped. Backing up and restoring pre-installed apps always creates a problem.
    I hope Nokia will update the backup application and include the option to select what is backuped. Until then the problem will remain.

  • I have ipad mini 2 updated to ios 7.1.2.  Now ipad keeps shutting down and rebooting to the apple logo. I factory reset and redownloaded software in recovery mode.  Still happening.  What else can I do?

    I have ipad mini 32gb.  I updated to IOS 7.1.2. Since then ipad keeps shutting down and rebooting to the apple logo.  It happens so many times I cannot use the ipad.   I have tried factory reset and reinstalled software in recovery mode. Ipad is only 1 1/2 years old and in great condition.  Is there anything else I can do besides soend $200 to fix it?

    Sounds like a hardware issue to me going by the CRC error you mentioned. I'd make a Genius Bar reservation (you'll need your Apple ID) if you have a nearby Apple Store and get it evaluated. The evaluation is free but repair/replacement could incur other charges.
    Genius Bar reservations:
    https://www.apple.com/retail/geniusbar/

  • Trying to clear unread emails shown as  a badge next to mail icon, have done network reset and now a complete factory reset and checked server. Any other thoughts on clearing these ghost emails??

    Trying to clear unread emails shown as a badge next to mail icon, have done network reset and now a complete factory reset and checked server. Any other thoughts on clearing these ghost emails?? Also can we get our old keyboard back that shows lower case and upper case?

    Understood, the difference with iTunes being that Apple doesn't (currently) require you to enter any account info on the device until you try to purchase something from their store. Initial setup is just a connection to the iTunes software and you're good to go.
    While I understand that RIM wishes the account to be defined, they also need to be aware that doing so during the initial setup without proving an option to do it later, while failing to provide any means to change it afterwards (short of a device wipe) doesn't always suit the the situation. Hopefully they'll be reviewing the forums to gather feedback that they can incorporate into future software updates.
    BESX 5.0.4, SQL 2008, Exchange 2010 SP2 RU4a

  • My ipad keeps freezing. I've factory reset and it still freezes

    my ipad keeps freezing. I've factory reset and it still freezes

    So you did a restore on the device?  Any particular action associated with the "freeze"?

Maybe you are looking for