2800 config with 4FXO VIC, voice-ports?

I'm trying to configure the voice-ports on a 2800 router with a 4 port FXO VIC and when I issue the voice-port command it only shows ports 50-50 so I use
voice-port 50/0/1 and it comes back with invalid input at marker and it points to the 50.
boot-start-marker
boot system flash flash:c2800nm-ipvoice-mz.124-4.T.bin
boot system flash flash:c2800nm-spservicesk9-mz.123-8.T8.bin
boot-end-marker
Lights on the FXO card are lit up but I do not have any cables plugged into them, am I missing something?
Thanks

I'm guessing this is the info on the pvdm2?
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC092447VB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00

Similar Messages

UC560 fxo with 4FXO VIC card.

Just wanted to confirm before purchasing how the UC560 handles PSTN Analog lines. We have 8 analog lines each with a different number.. example 123-456-7899, 123-456-7898, 123-456-7897 etc....
If the office wants to use one of the numbers as the "main" office number how would the UC560 handle the incoming calls? If someone dials the main number, lets say it will be 123-456-7899, what happens when a 2nd person dials it? Will the UC move that incoming call to another FXO port just like when doing outbound calls? If it works the way I mention above, that would allow for 8 people to call in on that 1 line and it will be spread between all 8 fxo ports.. does that sound correct?
Or, does the teleco company have to due the hunting for us?
Any insight would be appreciated.
Thanks,
J

Yes, telco has to do it. System cannot control how telco routes incoming calls. So, one has to ask telco to setup an hunt group, and define which addtional lines it will re-hunt calls. Depedning on situation these line can be incoming only, or bidirectional. In this case, special care must be give to the CO and system hunt scheme to minimize glare.
Also, please note if using a bunch of analog lines like you're planning, that will not get the best results to the users, like fast dialing, immedaite CLID display, automatic hunt as described above, DID service, digital voice quality, etc. For best results, one should only use ISDN PRI, or SIP trunk.
Finally, but very important: unless you have significant amount of expereince with telephony and netwrok, it is strongly recommened that for sure and quick results you get an UC certfied Cisco partner, or person of equivalente knowledge and expereince.

Saprouter config with RFC on tcp port 33xx

I have a customer who has configured saprouter to allow remote (from the Internet) connections via the SAP GUI. These connections work great. However, when they try to add entries to the route tables for TCP port 3300, 3301, and 3303 the external application they are using (a gateway connection on these ports) fails. Is there some special configuration which needs to take place to allow the RFC connections vs. the regular SAP GUI connections on ports 32xx?
Kind Regards,
Eric J.

I was able to fix the problem by configuring profile parameter "gw/alternative_hostnames" to the public IP of the SAP system.

SRST advice.translation-profile on voice-port drops after router reboot.

I have MGCP gateways that configured as SRST gateways too.
I have translation from internal numbers and vice verse then I use in config.
Here is the final result:
<b>
voice-port 0/0/0:15
translation-profile incoming 1
translation-profile outgoing 2
</b>
this translations work when gateway come in SRST fallback mode.
But
<b>
translation-profile incoming 1
translation-profile outgoing 2
</b>
configs drop from voice-port 0/0/0:15 when I have router reboot

You probably are using the 'ccm-manager config-server' command to download the MGCP config on registration. This is fine for basic operation, but part of the operation is that it will delete any existing voice configs. Therefore the voice port will be deleleted and this takes the translation profile along with it.
If your configuration is static and there are no changes being made on he CUCM gateway config, the easiest solution is to remove the 'ccm-manager config-server' command. Once you do this the other commands on the voice port will survive the reload since the router will no longer delete and then re-add the voice port.
If you do need the config download, you can use Embedded Event Manager (EEM) to re-add the translation profiles on the voice port after a reload. We would need a copy of your configuration to confirm the interface details to re-apply the configs against. If you want to try this option, paste your config into this posting.

VOIP home lab with cisco 2620 and VIC-2FXO port

Hi all,
I m considering building a home lab for studying CCVP, the lab would be based on the follow components :
- CUCM 8.X (already installed)
- A couple of soft phones running in VMWARE with IP Blue and CIPC (they are already in place and registered with the CUCM)
- Cisco router 2620 with NM-2V and VIC-2FXO-M2 (for europe, I'm in France)
so here are my questions :
1/ it looks like the NM-2V comes with integrated DSP, so I should not need more DSP, I have got one PSTN analogic line only so I can make only one call at a time, please confirm
2/ my analog line comes via my home internet provider dsl box, i have already tried to connect an analog phone and it works, please confirm the router will be able to receive and place calls
thanks for your help, I m looking forward to begin my voice lab

1. Yes, the NM-2V has built-in DSP resources for up to four calls (max voice port density with two 1st generation VICs). You cannot add further DSP chips to the NM-1V/2V, nor would you need to for what it does. You have one PSTN phone line, thus you can only make one call at a time. If you had a second line you could use the other FXO port for a second concurrent call.
2. If the phone line works then it will work with the router to make and receive calls. As Gregory said, just configure dial peers for what you need to do.
Here is some info on the NM-2V:
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_tech_note09186a0080094ac0.shtml

Unable to configure voice ports on cisco2811

I have configured the Voice Gateway and calls are working internally.
I recently installed a WIC-1B-S/T-V3 card to prepare to getting outside line access.
To try a set of Dial-Peer and put the port command , but I have been rejected.
I've confirmed that　IOS Version,compatibility of WIC,PVDM is installed.
How do I get my WIC card to work?
The following is a show command.
【try set up】
R1#conf t
R1(config)#dial-peer voice 100 pots
R1(config-dial-peer)#port 0/0/0
^
% Invalid input detected at '^' marker.
R1(config-dial-peer)#port ?
<50-50> Voice interface slot #
R1(config-dial-peer)#port 50/?
<0-0> Voice interface SubUnit #
R1(config-dial-peer)#port 50/0/?
<1-20> Voice interface port # within vic
R1(config-dial-peer)#port 50/0/1
^
% Invalid input detected at '^' marker.
【show voice port summary】(i know 50/x/x voice port is automatically created.)
R1#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
-- omission --
50/0/20 1 efxs up up on-hook idle y
50/0/20 2 efxs up up on-hook idle y
【show ip interface brief】
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.11.110 YES NVRAM up up
FastEthernet0/1 192.168.110.1 YES NVRAM up up
BRI0/0/0 unassigned YES NVRAM up up
BRI0/0/0:1 unassigned YES unset down down
BRI0/0/0:2 unassigned YES unset down down
Loopback0 1.1.1.1 YES NVRAM up up
【show diag】
R1#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
-- omission --
PVDM Slot 0:
16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8538-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC104518AZ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-16
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
BRI S/T - 3086 WAN daughter card
Hardware Revision : 1.0
Top Assy. Part Number : 800-24973-01
Board Revision : B0
Deviation Number : 0
Fab Version : 01
PCB Serial Number : FOC10515ZRK
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : WIC-1B-S/T-V3
Version Identifier : V01
【show inventory】
R1#sh inve
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V01 , SN: FHK0934F0HR
NAME: "Wan Interface Card BRI S/T (3086)", DESCR: "Wan Interface Card BRI S/T (3086)"
PID: WIC-1B-S/T-V3 , VID: V01 , SN: FOC10515ZRK
NAME: "PVDMII DSP SIMM with one DSP", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC104518AZ
【show version】
R1#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(7), RELEASE SOFTWARE (fc6)
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-7.bin"
Cisco 2811 (revision 53.51) with 247808K/14336K bytes of memory.
Processor board ID FHK0934F0HR
2 FastEthernet interfaces
1 ISDN Basic Rate interface
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
【show run】
R1#sh run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.110.1
ip dhcp pool VLAN10
network 192.168.110.0 255.255.255.0
default-router 192.168.110.1
option 150 ip 192.168.11.200
isdn switch-type ntt
voice-card 0
no dspfarm
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 192.168.11.110 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.110.1 255.255.255.0
duplex auto
speed auto
interface BRI0/0/0
no ip address
encapsulation hdlc
isdn switch-type ntt
isdn point-to-point-setup
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
router ospf 1
log-adjacency-changes
network 1.1.1.1 0.0.0.0 area 0
network 192.168.11.0 0.0.0.255 area 0
network 192.168.110.0 0.0.0.255 area 0
router ospf 12
log-adjacency-changes
ip http server
no ip http secure-server
control-plane
dial-peer voice 100 pots
destination-pattern 0T
incoming called-number .T
direct-inward-dial
call-manager-fallback
max-conferences 8 gain -6
ip source-address 192.168.11.110 port 2000
max-ephones 10
max-dn 20 dual-line
end

Hi,
the card which u are using supports Data .
you need to have VIC cards like VIC2-2BRI-NT/TE for Voice to work.
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/7960-2isdn-bri-vic.html
regds,
aman

No non-linear under voice-port to reslove hissing on NM-HDV

Hello.
I have a trouble with 2MFT on NM-HDV.
I can hear hissing on call.
So, i had configured no non-linear under voice-port, then i can't hear any hissing.
Instead, I can hear echo on call.
How can i fix it?
Regard,
john.

Hell Venky.
Thnak you for your helping.
I tried to configure based on the web site what did you told me.
But i couldn't success it to resolve echo issue.
The voice gate have 12.4(1a) on Cisco 2851.
So the solution to reslove echo doesn't fit in my case.
As i mentioned, normally i can hear noise each i talk another persion. If i stop the conversation i can't hear noise. but i started to talk again, i can hear noise each time.
Thus i tried to disable "no non-linear" parameter, i can hear echo instead noise.
So i should choice if i can hear noise or echo.
And also, i tried to change input gain and output attenuation from -6 to 14, but the each still can hear.
out voip network toplolog is below.
NEC Digital Phone---NEC PBX---Gateway---(cat6500---MSPP(WAN Area)---cat6500)---Gateway---NEC Digital Phone.
If i make a call using Normal Phone (INot Digital Phone), I can't hear noise. Whenever i can hear noise with NEC Digital Phone.
Here is the option on cisco 2851 with 12.4
2851(config-voiceport)#?
Voice-port configuration commands:
bearer-cap Specify the bear capability
busyout Configure busyout trigger event & procedure
comfort-noise Use fill-silence option
compand-type The companding type for this voice port
connection Specify Trunking Parameters
cptone Configure voice call progress tone locale
default Set a command to its defaults
description Description of what this port is connected to
disc_pi_off close voice path when disconnect with PI received
echo-cancel Echo-cancellation option
exit Exit from voice-port configuration mode
idle-detection Idle code detection for digital voice
input Configure input gain for voice
music-threshold Threshold for Music on Hold
no Negate a command or set its defaults
non-linear Use non-linear processing during echo cancellation
output Configure output attenuation for voice
playout-delay Configure voice playout delay buffer
shutdown Take voice-port offline
threshold Threshold [noise] for voice port
timeouts Configure voice timeout parameters
translate Translation rule
translation-profile Translation profile
trunk-group Configure interface to be in a trunk group
voice-class Set voiceport voice class control parameters
Please advise to me to reslove the problem.
Regard,
john.

Cisco 3640 cant configure voice-ports

I've an cisco 3640 with a VWIC-2MFT-E1 network module. Can anybody tell me why i cant configure any voice-port? without able to configure voice-port, i cant assign any port for my "dial-peer voice xx pots". Anybody has any solution?
what im trying to do is sending voice data traffic to 192.168.10.1
controller E1 1/0
framing NO-CRC4
clock source line primary
channel-group 0 timeslots 1-31
interface Serial1/0:0
bandwidth 2048
ip address 192.168.10.2 255.255.255.252
ip mtu 300
encapsulation ppp
no ip route-cache
no fair-queue
no cdp enable
dial-peer voice 777 pots
destination-pattern 77T
no digit-strip
direct-inward-dial
forward-digits all

I've only got this from my controller E1
Vertigo(config-controller)#?
Controller configuration commands:
channel-group     Specify the timeslots to channel-group mapping for an
                    interface
clock             Specify the clock source for a DS1 link
default           Set a command to its defaults
description       Controller specific description
detect            Enable detection of loopback request
exit              Exit from controller configuration mode
framing           Specify the type of Framing on a E1 link
guard-timer       Guard timer (0-20) for xcsp calls - timer duration and
                    accept/reject on expiry
help              Description of the interactive help system
line-termination Specify the line termination for E1
linecode          Specify the line encoding method for a E1 link
loopback          Put the entire E1 line into loopback
mode              Configure the controller mode
no                Negate a command or set its defaults
shutdown          Shut down a E1 link (send Blue Alarm)
tdm-group         Configure DS0 group for TDM
Do i need DSP for the voice-ports? Please guide me on what more module i need to get. Thanks!!
https://supportforums.cisco.com/message/3022639;jsessionid=AF45FBC0DDB8636D70F9B526A367016F.node0

Purpose of local-alerting under voice-port?

Hello;
During a recent migration I noticed a "local-alerting" command under a couple voice-port configurations:
voice-port 2/1:23
local-alerting
I did not enter the command in myself, and I checked with the other engineers and all are positive they did not enter the command.
These were found under T1 PRI circuit configs and only showed up under a few (2 or 3) from a set of about 12 total circuits on 2 seperate gateways.
I tried researching this command, and it is not under any command reference doc I looked through, google was of no help as well, it does not even come up as a listed command when entering "?" under voice-port......
Is any one familiar with this command?
What does it do?
Are there any reference documents or links?
Would it be possible for it to automatically appear after certain events? (no one recalls entering this in)
Any help would be greatly appreciated.
Thank you.

This command only makes sense when local bypass of DSP is used, In which case to use DSP to generate local bypass ringback. it's a hidden command, that's probably why you don't see it in the command reference or any document avaialble.
Br,
Nadeem
Please rate all useful post.

How can I get a video signal using IMAC 27 with only mini display port. I like to send the signal wireless to a TV using a TV/audio transmit system.

I have an IMAC 27 with a mini display port ( only this). I also have all the adapters ( mini display port to VGA, HDMI...).
Since I moved to UAE I like to transmit the signal frm my IMAC ( where I also look German TV on) to my TV. I will do so by using a wireless Transmit receive system with theree cinch inputs ( transmit system ( video, 2x voice).
The distance to the TV IS ABOUT 10m and one wall. I don`t want to use a cable.
Is there any solution for example mini display to VGA + VGA adapter to cinch so I can use the transmit system?
HDMI would also be an optiekn, bat then I have to by another Transmit receive system.
If somebody made already the experience I would appreciate to share the information
Is there may be any store in UAE where to get support. It is very diificult to get good advice here. They sell everything bat can not reaaly explain and have very often no technical knowledge. With this problem nobody until now can help me.
Hans
<Email Edited by Host>

I don't know what AppleTV can handle as far as bit rate is concerned, but increase the bit rate as high as it will let you. You are taking DV which is 25Mb/s and compressing it. If you're making an H.264, you should get great results needing no more than 6Mb/s. Bear in mind, the higher the bit rate, the larger the file size.

Fax Blocked Voice Port (FXS)

hi,
an outgoing fax call blocked my voice port. it stays in a busy state for days... shut and no shut doesn't put the voice port in a dorm state again, only a reload will correct it... is there any solution instead reloading the c2800?
many thanks

Dino -
If you are running IOS 12.4, This seems to be attributed, possibly, to a known bug with the FXS port:
Cisco bug ID CSCse83674
http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCse83674

AS5300 - Voice Port Configuration Problem

Hi guys,
I'm trying to configure a E1 PRI 8 Port Module on a AS5300 (IOS: 12.3(18)) but after I configured the controller, I can't find the voice ports. if I do a sh voice port summ there are no voice ports listed.
The controller is showing up in sh controllers e1 0.
Also under the dial-peer there is no port command..
Anybody has had this issue before?
Thanks.
Best regards

here are the outputs:
Router#sh vers
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-JS-M), Version 12.3(18), RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Wed 15-Mar-06 16:39 by dchih
Image text-base: 0x60008AEC, data-base: 0x618EC000
ROM: System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
BOOTLDR: 5300 Software (C5300-BOOT-M), Version 12.1(17), RELEASE SOFTWARE (fc1)
Router uptime is 3 hours, 53 minutes
System returned to ROM by reload at 16:26:08 gmt Sun Jan 2 2000
System image file is "flash:c5300-js-mz.123-18.bin"
cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes of memory.
Processor board ID 14898234
R4700 CPU at 150MHz, Implementation 33, Rev 1.0, 512KB L2 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
35 Serial network interface(s)
240 terminal line(s)
8 Channelized E1/PRI port(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
Router#sh run
Building configuration...
Current configuration : 2057 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
spe 1/0 2/9
firmware location system:/ucode/mica_port_firmware
resource-pool disable
clock timezone gmt 2
no aaa new-model
ip subnet-zero
ip cef
isdn switch-type primary-net5
isdn voice-call-failure 0
voice call send-alert
voice rtp send-recv
voice service pots
voice service voip
sip
voice class codec 1
voice class codec 100
controller E1 0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 1
clock source line secondary 1
controller E1 2
clock source line secondary 2
controller E1 3
clock source line secondary 3
controller E1 4
clock source line secondary 4
controller E1 5
clock source line secondary 5
controller E1 6
clock source line secondary 6
controller E1 7
clock source line secondary 7
interface Ethernet0
no ip address
interface Serial0
no ip address
clock rate 2015232
no fair-queue
interface Serial1
no ip address
clock rate 2015232
no fair-queue
interface Serial2
no ip address
clock rate 2015232
no fair-queue
interface Serial3
no ip address
shutdown
clock rate 2015232
no fair-queue
interface Serial0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice modem
no cdp enable
interface FastEthernet0
ip address 1.1.1.1 255.255.255.252
duplex auto
speed auto
ip classless
ip route 0.0.0.0 0.0.0.0 1.1.1.2
no ip http server
dial-peer voice 100 voip
destination-pattern .T
session protocol sipv2
session target ipv4:192.168.1.1
session transport udp
dtmf-relay rtp-nte
dial-peer voice 10 pots
destination-pattern .T
direct-inward-dial
sip-ua
no remote-party-id
sip-server ipv4:192.168.1.1
line con 0
line 1 240
line aux 0
line vty 0 4
transport input lat pad mop telnet rlogin udptn
end
Router#
Router#sh diag
Motherboard Info:
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 1.80, Item Number 800-2544-03,
Board Revision A0, Serial Number 14898234,
PLD/ISP Version 0.0, Manufacture Date 8-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 30 01 50 03 20 00 09 F0 03 41 00 31 34
   0x10: 38 39 38 32 33 34 00 00 00 00 00 00 00 00 13 63
   0x20: 07 08 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS5300
Slot 0:
Hardware is Octal E1 PRI, 8 ports
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x49,
Board Hardware Version 1.0, Item Number 800-3883-01,
Board Revision A0, Serial Number 14896274,
PLD/ISP Version 0.1, Manufacture Date 29-Jun-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 49 01 00 03 20 00 0F 2B 01 41 00 31 34
   0x10: 38 39 36 32 37 34 00 00 00 00 00 00 00 00 13 63
   0x20: 06 1D 00 01 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-8CE1+=
Slot 1:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14049055,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 34 39 30 35 35 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Slot 2:
Hardware is Duo Density Modems
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4C,
Board Hardware Version 1.0, Item Number 800-3680-01,
Board Revision A0, Serial Number 14055218,
PLD/ISP Version 2.2, Manufacture Date 7-Jul-1999.
EEPROM format version 0
EEPROM contents (hex):
   0x00: 00 01 01 4C 01 00 03 20 00 0E 60 01 41 00 31 34
   0x10: 30 35 35 32 31 38 00 00 00 00 00 00 00 00 13 63
   0x20: 07 07 02 02 FF FF FF FF FF FF FF FF FF FF FF FF
   0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
   0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FRU NUMBER : AS53-120-CC2=
Router#

VIC 1280 vs VIC 1240 + Port Expander

Hello,
What's the benefit of using VIC 1240 + Port Expander versus having a VIC 1280?? I don't see any.
Anybody has some inputs?

The port expander add-on will not be as costly as the 1280 VIC. The blades do not have 2 Mezz slots - they have a single Mezz slot and mLOM. You can't install a 1280 into an M3 expecting this will leave one additional slot available. If you're purchasing M3's blades with the 1240 mLOM, it makes more sense to just add-on the expander rather than add a full 1280 VIC on top of it. The expander also uses a fraction or power as the 1280 VIC. The most important difference is how the BW is aggregated
The mLOM + Expander can provide up to 40Gbps of aggregated/Port Channeled BW per fabric.
The 1280 VIC can provide up to 20 Gbps of aggregated/Port Channeled BW per fabric.
The mLOM + 1280 can provide up to 2 x 20Gbps aggregated/Port Channeld BW per fabric.
So you get no BW increase on the blade by using a 1240+1280 rather than the 1240+Expander. You do however get 2 adaptors per device for the host to manage, rather than 1.
Keep in mind, to achieve the max BW capacity to the blades you require 2nd GEN I/O Modules (2204/2208).
Regards,
Robert

C460-M2 with 2 VIC-1225, managed by UCSM

C460-M2 with 2 VIC-1225; all documents show only one VIC-1225 (which has to be in PCI slot nr.1) single wire managment with a UCS FI ?
Is this a limitation ? or must the second VIC-1225 be connected to a switch outside the FI ?
Walter.

I received the following answer
Good question Walter. The documentation is confusing. If running the C460 as part of a UCS integration, only 1 card is supported.Although the server supports 2 cards , slot 1 & 2 according to the specsheet. The datasheet states that upto 3 VIC can be supoprted int he server.
The Cisco CCW config tool allows you to configure 2 VIC1225 in the C460.
From the 460 spechseet.
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/ps11587/spec_sheet_c17-662220.pdf
Page 24
The C460 server accommodates the Cisco 1225 Virtual Interface card, which is supported only in slots 1 and 2. Note, however, that if the server is running UCSM, only slot 1 is supported for the VIC card.
■ The Cisco Card NIC mode is currently supported only with a Cisco 1225 VIC (UCSC-PCIE-CSC-02) that is installed in PCIe slot 1.
■ The C460 server accommodates the Cisco 1225 Virtual Interface card, which is supported only in slots 1 and 2. Note, however, that if the server is running UCSM, only slot 1 is supported for the VIC card.
From the datasheet
http://www.cisco.com/en/US/prod/collateral/modules/ps10277/ps12571/data_sheet_c78-708295.html
System Requirements
The Cisco UCS VIC 1225 is designed for use only on Cisco UCS C-Series Rack Servers. A single Cisco UCS VIC 1225 is supported on Cisco UCS C260 M2, C460 M2, C220 M3, C240 M3, C22 M3, and C24 M3 rack servers. Up to three Cisco UCS VIC 1225 cards are supported on these servers depending on the slot configuration.
Anyone at Cisco want to clarify the above?
Message was edited by: NABIL YAGHI

I want to sync my Voice Memos but iTunes 10.5 will not let me even with the "include voice memos" checkbox selected.

I want to sync my Voice Memos but iTunes 10.5 will not let me even with the "include voice memos" checkbox selected. As well Ive deselected all the music in itunes so when I sync there will be none on my phone but itunes also ignores this request and puts purchased music back on. I do not have autofill selected. Also wondering where the backup of my iphone 4s is located on my hard disk. Any help greatly appreciated.

Sorry thats itunes 11.5

2800 config with 4FXO VIC, voice-ports?

Similar Messages

Maybe you are looking for