290x Lightning Black Screen

Board: GIGABYTE GA-Z97X-UD3H-BK
Bios: F7 2015/04/22
VGA: 290X Lightning
PSU: Corsair HX Professional Series 750-Watt 80 Plus Certified - CMPSU-750HX
CPU: Intel Core i7-4790k
MEM: G.SKILL Sniper Low Voltage Series 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model F3-12800CL9D-8GBSR2
HDD: OCZ Technology 120GB Agility 3 - AGT3-25SAT3-120G
COOLER: CORSAIR Hydro Series H110 Extreme
Currently no overclock
OS: Windows 8.1 64bit
I have had this card since early February and have been running it without issue. It was stress tested in furmark immediately after install without bsod or reboot. The problem started about a week ago. I woke up in the middle of the night due to the fans running at 100% on the card. I could not get the screen to wake. I had to connect to the onboard passthrough from the i7. It did start working again after several reboots. The problem seems to pop up randomly. Either in the middle of the night when nothing is running or during light browsing. The issue never occurs when gaming. When the problem happens the blue lights indicating power usage do not light up. Currently the card is still installed but it is not coming back up after several reboots. I am currently running off of the IGP with no issue. The problem appears to be exclusive to the card.

Did some more testing tonight. My computer had been off all day today while at work. I switched my monitor back to the 290x and booted. The card was recognized and displayed correctly. I then ran furmark for two hours while running a cpu stress test as well. There was no issue what so ever. Later in the evening I watched a youtube video and the display cut out when it was closed.
I can try another card tomorrow night. It's a 570 gtx which would only be a test to see if the behavior is specific to the discrete video as this issue doesn't seem to effect the IGP.

Similar Messages

MOVED: R9 290X Lightning - Black screen freezing

This topic has been moved to Graphics Cards.
https://forum-en.msi.com/index.php?topic=254587.0

So I decided to RMA the card a few days ago. I'd been running perfectly on the integrated graphics while I waited for my replacement. I just recently installed it and it worked great... for about 5 minutes and then I got a black screen accompanied by the gpu fans blowing full speed. I immediately shut off the pc and have not been able to boot with the card anymore. Even if it's all installed and properly plugged in it is not recognized in windows and won't show up at all in the bios board explorer (says PCIe slot is empty). At this point I'm thinking it might be the motherboard but the card also refuses to work on other setups. I've also tried different power supplies with no success. At this point I'm thinking of just trashing this card and going with an nvidia since my friend's card (gtx960) works fine on my pc.

Msi 290x gaming - black screen crash

Hi
Recently i bought MSi 290x gaming . After a day i has got first black screen freeze. Only way to turn on computer was unplug it and connect again after 10-20 sec. I try to use different drivers but nothing helped. Sometimes pc worked fine for 2-4 days and them 3-5 crashes in hour. It never happened in a game . always in windows . I tried different psu and nothing change .
I tried msi afterburner , set voltage to constant. change gpu memory clock ..... but nothing changed :(
I make decision to RMA card to the shop but they just send me msg that everything was fine :( any ide what i should do ?
AMD fx-8350
Asus formula z
XFX Black Edition 850W Fully Modular 80+ Gold Power
2x 8GB 1866MHz DDR3 CL10 DIMM HyperX Fury Black Series
Now im running my old gtx 460 and everything looks fine :((
Any advice?
I should maybe try to sell card and buy something else like gtx970 but i just spend 270 pounds and im at least not happy .... huge disappointment

Not much to try then. Make sure bios of your board is latest and check general system stability with prime95: http://www.mersenne.org/download/

R6970 lightning, black screen after starting Windows screen

Alright so I've been getting a few random bsod saying something about non paged error. At first it was random sometimes in Windows sometimes before the login screen. But then it became consistent, couldn't boot to Windows at all after the starting Windows screen it would bsod everytime. So ran memtest and system repair off the disk and found no errors. So then one time I found the bsod showed an error with atikmdag so then I started to look into driver issues. Deleted catalyst, the drivers and then rebooted. Long and behold it booted Windows fine. Once I loaded Windows it said installing device driver for the graphics card, it finished and prompted a reboot. So I did but on start up after the starting Windows screen it just goes black. Will go into safe mode fine but otherwise black. And it will do that with an old driver, new driver, whether I install with catalyst or Windows does it. Switched via bios and no screen at all on any other setting than the middle switch. So grabbed a gtx 650 from my brother and plugged it in and it booted fine, installed the driver and no problems. So is my card shot or is there something I am missing? Do I have a corrupt bios and need to flash it?
Another note it ran games fine and wouldn't crash but when it was just sitting with Google Chrome and a few tabs is when it started having problems.
System specs
I5 3570k @4.6ghz
Asus maximus v formula
16gb (2x8gb) gskill ram 1333 @1600
R6970 lightning s/n: 602-v237-020B1109228417
Windows 7 pro 64bit sp1 up to date
Lucid logixs enabled
Oct 750 power supply

save and upload current vbios of the card to check it

MSI 290X LE Lightning Edition black screen problem

I recently bought the above graphics card, only to run into problems with black screen, furmark blackscreens when it reaches just over 70c & games that push the card ie Crysis 3 also causes black screen problems, I'm also sometimes getting desktop corruptions, usually after it black screened.
My PSU is a 850watt EVGA SuperNova G2 so i know it's not that what causing the problem.
rest of my setup as follows
3770K @4.2Ghz
MSI Z77 Mpower
8GB corsair memory
ect ect.
Any idea's as to the cause of the problem?
edit here what it doing I've uploaded it to youtube.

First of all remove any oc. Then list specs more detailed: >>Posting Guide<<

Ipod touch 5th generation battery screen with lightning bolt locked cannot charge or restart. ive tried everything from new cables attempting to shut down but stays at screen for a few seconds then black screen again over and over

screen locked up and shows the battery with low red and ligtning bolt and cannot hard shut down or reset just stays there for a few seconds then black screen. hooked up to computer and itunes doesnt recognize it or even shows that it is pluged in. looked and made sure nothing is broken or metal in ligting port or on cable which would prevent it from accepting a charge. ipod is only a month old and seems like a waste of money if its so hard to try to get an explanation of why this is ive been tryning to get an answer from apple for a week now.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

MSI N580GTX Lightning Extreme Edition (Black Screen / Reboot)

Hi everyone !
Here's my computer specs :
CPU: Intel I7 870 (2.93 Ghz)
MoBo: Micro ATX from my Dell XPS Studio 8000
Memory: 6Go DDR 667 Mhz
PSU: Corsair HX750(w)
Windows 7 Pro 64 Bits
My problem :
80% of my games (Crysis 1 & 2, Bulletstorm,...) & benchs (3DMark 11, MSI Kombustor, ...) crashes after few seconds. My graphic card goes off, black screen, and then my computer automatically reboot. I've tried another PSU, same pb, and my Corsair HX750 is new. So I wonder if the problem is from my graphics card or my (dell) motherboard ? But my config has the minimum required by MSI.
My temporary solution
After few tests with differents drivers, I've try to change the Core Voltage, no result... So I decided to downclock the GPU freqs.
In order to have something stable to 100%, and be able to run all the games and benchs, i've to downclock the GPU like :
Core Clock : 600 Mhz (Original : 772 Mhz)
Shader Clock : 1200 Mhz (Original : 1544 Mhz)
Memory Clock : 1730 Mhz (Original : 2004 Mhz)
Its a big loss frequency!
Hope a new bios will come out to fix the bug.

Quote
Display driver : ForceWare 280.26
have you tried MSI's drivers for your card?
==> http://www.msi.com/product/vga/N580GTX-Lightning-Xtreme-Edition.html#/?div=Driver&os=All
Remove current driver with >>Driver Sweeper<< in 'Safe Mode' before install the new one
Quote from: Frakatchoo on 07-September-11, 22:13:04
It's only unstable when i'm use the GPU (Games & benchs), not HD videos.
Most games/bench crashes with default clock @ 1.031v. I tried to overvolted & undervolted the GPU, but my tests were not conclusive. The only way i've found to have all games/benchs stable is to downclock the GPU as I explained in my first post.
Maybe i need a more accurate GPU voltage ? Is it important to change Memory & Aux voltage too ?
have you tested with 1050mV for core?
Quote
Is it important to change Memory & Aux voltage too ?
normally not, but depend what exactly is unstable
But it should work fine by default as is

MSI 7970 Lightning GHz Edition, black screen problem

Hi all,
I am very dissapointed on the MSI product now. I bought MSI 7970 Lightning BE GHz Edition, when I don't overclock the graphics card and play games I will get black screen or sometime I will get message that "AMD graphics card stopped responding". So I bought a 950W PSU but still problem is there. If I underclocked the card at 600MHz both GPU and memory clock I don't get the problem. But what's the point of having this card paid $500 for nothing. I am so fed up with this card. Please someone help....
My System Spc :
Asus P8Z77-V LX motherboard
16GB RAM
Core i7 3770
PC Power and cooling MKII 950W PSU
Thanks.

watch the attitude! you have got a faulty card it happens occasionally as all manufacturers have a 1-3% defective rate not just MSI so do not start with your bashing as its against the rules here!
there are hundreds of individual parts on a board and any one can go bad causing a problem so if you are going to bash anyone bash AMD's GPU's as that is the most likely problem here on the card and MSI do not make those so keep your "I learned a lesson about MSI... it's a piece of junk" to yourself !
>>Please read and comply with the Forum Rules.<<

MSI R9 290x lightning

MSI gotta hand it to yea, the 290x lightning is by far the best 290x there is, loving the hell out of it. Idle temps 38 max temps 68 on stock clocks 1080/1250.Right now running stable 1200/1500 on air, idle temps 38-40 and max temps in BF4 after hours of playin 72c hahahhaha. Nice job!!!!

Quote
Normal UEFI implementations have always a fallback option to CSM to boot in legacy Mode!
A card with a (hybrid) GOP vbios doesn't boot if used on an UEFI mainboard that is not GOP compliant. Therefor socket 1155 and 2011 boards without a current GOP compliant bios are stuck with a black screen if used with a card using a GOP vbios. While it the card can work in legacy mode that is only without issues in a board with a pure legacy bios. If the UEFI board is GOP compliant legacy and UEFI booting works.
Therefor the card coming with a legacy vbios prevents rmas because of such issues. Who wants UEFI booting can request a GOP vbios. As the card already has two vbios versions (normal/LN2) there is no way for another chip.
If you want to complain further contact MSI about it: >>How to contact MSI.<<

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

Why does my iPad have a black screen and won't turn on even when I try charging it

I just got a survivor case today and put it on my iPad and it stopped working and just has a black screen even when I try charging it

Not charging
1. Reset iPad
2. Try another wall socket
3. Try another cable (make sure it's an original Apple cable)
4. Try another charger (make sure it's an original Apple charger)
5. Clean Lightning port with compress air or new paint brush

Black screen with new GPU

I just purchased a K450e and upgraded it with an SSD, 650 watt PSU, and Radeon R9 290. Unfortunately, after installing the GPU, I get only a black screen. I've been through previous posts and disabled secure boot and switched boot mode to legacy. Still nothing. The onboard graphics work if I take the card out, but when I put it in, I get no output from either. Any help??

Hi praziquantal,
Have you tried toggling the BIOS switch on the r9 290.
See the Details below from
http://www.guru3d.com/articles-pages/radeon-r9-290-review-benchmarks,15.html
Spoiler (Highlight to read)
The AMD Radeon R9 290 and 290X comes flashed with two separate BIOSed for testing. The bios can be toggled by the small black switch located on the top of the part closest to the mounting bracket that you plug your displays into. You must reboot after toggling the switch for changes to take effect.
The AMD Radeon R9 290 and 290X comes flashed with two separate BIOSed for testing. The bios can be toggled by the small black switch located on the top of the part closest to the mounting bracket that you plug your displays into. You must reboot after toggling the switch for changes to take effect.
Hope this helps
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

HAVE NEW 13.3 MAC AIR AND when using it to open sites in safari I have no issue until I go to a link page that is a pdf file or I am trying to save the screen info as a pdf. I only get a black screen with no data, cannot find solution in help menu

HAVE NEW 13.3 MAC AIR (previously, still have 13.3 MCbook pro which works captures what I am looking for an answer to)
when i open sites in safari the page opens fine if it is not a pdf based page.
Once i open a site that has a link to another page that is a pdf based page the page comes up as a black screen with no info showing
If I open a site that gices me an open to save a file to a word, excel type document or a pdf , everything works fine until I try to save the information to a PDF and again the screen goes black
I have tried the safari help site but to no avail, does anyone have a solution to thid problem. (I do have the abode ofr mac program loaded)

If you delete all the Adobe Reader stuff it will probably fix this. For almost everything, the Apple pdf handling works better.

Start-up problems, black screen or open firmware

My iBook G4 1.33GHz Dual USB, with 1 gb RAM memory has been troublesome lately. It's installed with the latest version of OS 10.4.9
When starting up the ibook, it will sometimes only show a black screen after the boot chime. Repeated force restart sometimes makes it boot up the open firmware (white screen).
Then I see the error message:
"Illegal instructions at: %SRR0:ff85e778 %SRR1:00081000"
When I continue on with "mac-boot", I get the blue screen with a question marked box. So it can't find the startup disk.
This usually only happens when I'm done working for the day and close the lid on my ibook without manually clicking on the sleep mode when I put in in my drawer,. I've seen several times that the screen is still on when I close the lid, so it will continue to burn battery time.
I've managed to get the ibook to boot properly after removing the battery and letting it "cool-down" for 15-20 min. Also, zapping pram, vram sometimes works, but I don't know how much that actually helped. It worked once when I typed in the reset-nvram in the open firmware screen too.
I'd rather not have this happen at all! Any suggestions? Is this the much-talked about RAM memory failure?
Any suggestions would be very appreciated.
Message was edited by: antony chen

HI,
*"I get the blue screen with a question marked box."*
That can mean several things. One, the drive is failing. Two, your iBook can't find a System Folder to boot from. Try booting while holding down the Option key which will prompt the Startup Manager window.
MemTest
Boot from your install disk and check the hard disk for errors.
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
Select your start up disk and click Restart
While you have the Disk Utility window open, look at the bottom of the window where you see Capacity and Available. Make sure there is always 15% free disk space. Not enough disk space can cause directory corruption.
If you cannot boot from your install disk, try booting in Safe Mode
A flashing question mark appears when you start your Mac
Carolyn

My iMac 8.1 was slowing down and had permissions problems. I backed everything up, and then re-installed. Now all I get is a black screen. Power+D gives me a hardware error message: HDD-1336. Help!

My iMac 8.1 (10.6.8 ) was slowing down and had recurrent permissions problems, mostly with Java. I backed everything up, and then re-installed from time machine. Now all I get is a black screen which says I need to reboot. Power+D gives me a hardware error message: 4 MOT/1/40000003: HDD-1336 or HDD-1327. When I reboot from the OSX CD and start disc utilities everything checks out OK. When I reload 10.5.2 from the OSX CD everything seems to work OK and no more permissions problems. But then I loose all my email and safari stuff. Anyone have any ideas short of going back to my old PC?

DonM. wrote:
Hi
Thanks for the help. No point in fooling around with it any more. Will I be able to use it as a monitor if I get a mimi mac?
Cheers. Don
No unfortunatley it's too old, you are referring to Target Display Mode which became avialble in 2009, your 2008 needs to have the HD replaced. I'd still do that if everything else is OK or you can simply buy a new MM and display or even a new iMac or an Apple refurbished iMac to save money.

290x Lightning Black Screen

Similar Messages

Maybe you are looking for