2950 appears dead System Light Flashing stat light stays on

I think I have a dead switch. However, I figured I would see if anyones had a similar situation. When I power the device up the stat light comes on and stays on. Then the port lights flash once then the system light starts flashing. Once the system light starts fashing the switch appears to hang. It's not responding from the console port. The other switch is I have is a 2950 as well and it's responds via the terminal emulation settings I've set up. I think I know the answer, but I'm indulging in a little wishful thinking. Lastly I hold down the mode button for 15 to 30 sec and I dont get any change in status. Should I feed this switch to my garbage can?

If the console port does not respond, there is not a whole lot you could do. If you have a service contract, open a TAC service request and get it replaced.

Similar Messages

Bold 9930 - dead and flashing red light

Bold - Verizon 9930, died with flashing red light, non-responsive. Can connect wtih loader, re-loading latest OS for Verizon (7.1.0_rel1737_PL5.1.0.429_A7.1.0.580_Verizon_Wireless) Load fails with "application loader was unable to connect with your device" when it tries to connect with the JVM. I have tried:- fully charged known good battery (tested in another 9930)- wiping device- start without battery, insert battery when JVM message comes up- both BB desktop and Loader directly- two different PCs (no change)- different USB ports- older version of BB OS for device- many, many iterations... All end with "application loader was unable to connect with your device" Is the device scrap? If so why? It's not even 2 years old, out of warranty, and apparently now totally worthless. This one is the CEO's Blackberry, and he's not happy... If I can't resolve this, it will be the very last BB to ever see the inside of our company. This is the second 9930 to die this way in the last 4 weeks.

Hello,
Firstly...
truckin-on wrote:
Does RIM care about these failure issues at all I wonder?
If you were hoping for a response from RIM, you have misunderstood the purpose of these forums. These are not a channel for any communications with, support from, nor escalation to RIM for anything. Rather, these are a user-to-user community of volunteers trying to help each other out amidst their own busy lives. So patience perhaps would be a good thing to have...
Nevertheless, please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
While you've already validated that your battery is good, I don't think you've tried the first part of this test:
Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem.
While perhaps redundant to what you've already attempted, here are a few more things to try:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
Since you are out of warranty, your next step I suppose would be to seek in-hand support from a qualified technician to give you a proper diagnosis. Doing such at this internet distance is quite a challenge and therefore cannot replace in-hand evaluation and diagnosis.
Good luck and let us know!

Dead MacBook : nothing on screen , flashing status light (6 times)

Hello
My Dad has a MacBook (early 2006) which worked flawlessly until it did not boot one morning.
Now he has a black screen, nothing when powered up except, if you maintain power pressed, 6 times flashing status light.
- Restoration CD did not do anything because it could not load (CD doesn't eject, has to use the "business card in the slot" trick to eject the disc).
- All resets did not do anything (power button for 5 secondes with no battery or power cord, cmd + option + p + r either)
- Could not run diagnostics
- Apple certified repair center saif motherboard is fried, costs the price of a brand new MacBook to change it.
Do you have any idea about what happened ?
Do you know how to reset something ?
Do you know what those 6 flashes mean ?
I read restoration CD can be used while status is displaying 3 short flahes, 3 long flashes. Does it work on a dead MacBook ?
Thanks a lot in advance everyone !

clementjoubert wrote:
Hello
My Dad has a MacBook (early 2006) which worked flawlessly until it did not boot one morning.
Now he has a black screen, nothing when powered up except, if you maintain power pressed, 6 times flashing status light.
- Restoration CD did not do anything because it could not load (CD doesn't eject, has to use the "business card in the slot" trick to eject the disc).
- All resets did not do anything (power button for 5 secondes with no battery or power cord, cmd + option + p + r either)
- Could not run diagnostics
- Apple certified repair center saif motherboard is fried, costs the price of a brand new MacBook to change it.
Do you have any idea about what happened ?
Do you know how to reset something ?
Do you know what those 6 flashes mean ?
I read restoration CD can be used while status is displaying 3 short flahes, 3 long flashes. Does it work on a dead MacBook ?
Thanks a lot in advance everyone !
Sounds like a simple dead motherboard, there's no better explanation than that, I'm afraid. If you didn't get AppleCare, then you're out of luck.

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

Think you need to provide some more details about what you are connecting

I have the ishuffle 2nd generation. When I plug in, itunes recognizes it but it will not charge. The green light flashes a few times but then goes out. I'm not sure if the battery is dead or if something else can be done. Any advice?

I have the ishuffle 2nd generation. When I plug it it, itunes recognizes it but the light flashes green a few times and then stops. It is not charging. Is the battery dead or can something else be wrong? Any advice??

To rule out a problem with the shuffle's onboard software, I would try a Restore on the shuffle using iTunes. The Restore button is on the shuffle's Settings screen in iTunes. This will erase the shuffle, reinstall its software, and set it to default settings.
If that does not help, you should do a test to confirm there is not a problem on the USB port, such as lack of power to operate the iPod and charge it battery. Shut down (power off) the computer and disconnect all USB devices including hub, except for standard keyboard and mouse (if normally used). If the computer is a laptop, connect its power adapter (so that it's not running on battery power). Do this to reset the shuffle
http://support.apple.com/kb/ht1655
Start up computer, run iTunes, and connect shuffle to a direct USB port on the computer.
If that does not help, it is more likely that the problem is a hardware problem on the shuffle, such as the battery.

My appears to be working but amber light flashes

Just bought an airport extreme to improve my wifi for my apple tv and iPad it seems to work but the light keeps flashing amber.
Any ideas?

The flashing amber light indicates that a setting needs to be adjusted or there might be firmware update for the product.
What operating system are you using on the computer that you used to configure the AirPort Extreme?
If you have a Mac, and you are not sure....
Click the Apple icon in the extreme upper left hand corner of the screen and then click About This Mac to see the OS X version number.

Macbook air camera light flashing on resume?

Hi guys, my Macbook air (11 inch, mid 2011) has recently had its facetime camera light flashing on resume when I open the macbook lid. The time period when it flashed varies, but I am worried about security, and if someone has access to the camera.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve your problem.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to gather information about the state of your computer. That information goes nowhere unless you choose to share it on this page. However, you should be cautious about running any kind of program (not just a shell script) at the request of a stranger on a public message board. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them.
Here's a summary of what you need to do, if you choose to proceed: Copy a line of text from this web page into the window of another application. Wait for the script to run. It usually takes a couple of minutes. Then paste the results, which will have been copied automatically, back into a reply on this page. The sequence is: copy, paste, wait, paste again. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in your browser, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin; clear; Fb='%s\n\t(%s)\n'; Fm='\n%s\n\n%s\n'; Fr='\nRAM details\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; M () { find -L "$d" -type f | while read f; do file -b "$f" | egrep -lq XML\|exec && echo $f; done; }; Pc () { o=`grep -v '^ *#' "$2"`; Pm "$1"; }; Pm () { [[ "$o" ]] && o=`sed -E '/^ *$/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o=`echo $o`; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; R () { o=; [[ r -eq 0 ]]; }; SP () { system_profiler SP${1}DataType; }; id | grep -qw '80(admin)'; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; SP Software | sed '8!d;s/^ *//'; o=`SP Hardware | awk '/Mem/{print $2}'`; o=$((o<4?o:0)); Ps "Total RAM (GB)"; o=`SP Memory | sed '1,5d; /[my].*:/d'`; [[ "$o" =~ s:\ [^O]|x([^08]||0[^2]8[^0]) ]] && printf "$Fr" "$o"; o=`SP Diagnostics | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; p=`SP Power`; o=`awk '/Cy/{print $NF}' <<< "$p"`; o=$((o>=300?o:0)); Ps "Battery cycles"; o=`sed -n '/Cond.*: [^N]/{s/^.*://p;}' <<< "$p"`; Ps "Battery condition"; for b in Thunderbolt USB; do o=`SP $b | sed -En '1d; /:$/{s/ *:$//;x;s/\n//p;}; /^ *V.* [0N].* /{s/ 0x.... //;s/[()]//g;s/$.*: $$.*$/ $\2$/;H;}; /Apple|SCSM/{s/.//g;h;}'`; Pm $b; done; o=`pmset -g therm | sed 's/^.*C/C/'`; [[ "$o" =~ No\ th|pms ]] && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; [[ "$o" =~ =\ [^GO] ]] || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; d=(/ ""); D=(System User); E=; for i in 0 1; do o=`cd ${d[$i]}L*/L*/Dia* || continue; ls | while read f; do [[ "$f" =~ h$ ]] && grep -lq "^Thread c" "$f" && e=" *" || e=; awk -F_ '!/ag$/{$NF=a[split($NF,a,".")]; print $0 "'"$e"'"}' <<< "$f"; done | tail`; Pm "${D[$i]} diagnostics"; done; [[ "$o" =~ \*$ ]] && printf $'\n* Code injection\n'; o=`syslog -F bsd -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|last value [1-9]|n Cause: -|NVDA\(|pagin|SATA W|ssert|timed? ?o' | tail -n25 | awk '/:/{$4=""; $5=""};1'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); o=${s[2]}%; Ps "CPU usage by process \"$s\" with UID ${s[1]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); s[2]=${s[2]%[+-]}; o=$((s[2]>=25000?s[2]:0)); Ps "Mach ports used by process \"$s\" with UID ${s[1]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | awk 'NR>1 && !/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|post[fg]|x)/{print $3}'`; Pm "Extrinsic system jobs"; o=`launchctl list | awk 'NR>1 && !/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`for d in {/,}L*/Lau*; do M; done | grep -v com\.apple\.CSConfig | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`for d in /{S*/,}L*/Star*; do M; done`; Pm "Startup items"; o=`find -L /S*/L*/E* {/,}L*/{A*d,Compon,Ex,In,Keyb,Mail/B,P*P,Qu*T,Scripti,Servi,Spo}* -type d -name Contents -prune | while read d; do ID=$($PB\ :CFBundleIdentifier "$d/Info.plist") || ID="No bundle ID"; [[ "$ID" =~ ^com\.apple\.[^x]|Accusys|ArcMSR|ATTO|HDPro|HighPoint|driver\.stex|hp-fax|\.hpio|JMicron|microsoft\.MDI|print|SoftRAID ]] || printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find -L /u*/{,*/}lib -type f | while read f; do file -b "$f" | grep -qw shared && ! codesign -v "$f" && echo $f; done`; Pm "Unsigned shared libraries"; o=`for e in DYLD_INSERT_LIBRARIES DYLD_LIBRARY_PATH; do launchctl getenv $e; done`; Pm "Environment"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; Ps "DNS"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; f=auto_master; [[ `md5 -q /etc/$f` =~ ^b166 ]] || Pc $f /etc/$f; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; Pc "hosts" <(grep -v 'host *$' /etc/hosts); Pc "User launchd" ~/.launchd*; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l | sed 's:/Users/[^/]*/:/Users/USER/:g'); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed -E 's/(\..*$|-[1-9])//g'; o=`find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ | wc -l`; Ps "Restricted user files"; cd; o=`SP Fonts | egrep "Valid: N|Duplicate: Y" | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist | while read f; do plutil -s "$f" >&- || echo $f; done`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} file count"; done; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know your password, or if you prefer not to enter it, just press return three times at the password prompt.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line "[Process completed]" to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report your results. No harm will be done.
8. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of Apple Support Communities ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Cisco 1130 status light flashing orange

hello,
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.
I did a factory reset and it was ok ... past 3 days the problem has happened again ...
I changed the ap with a new but the situation remained ...
I tested the wiring and everything is ok.
the switch port is set up correctly
may be what??
problem switch??or problem ap??

hello,
I connect the console in to the WAP and then reboot the result of the bootup is as follows:
Xmodem file system is available.
flashfs[0]: 26 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 6858240
flashfs[0]: Bytes available: 9140736
flashfs[0]: flashfs fsck took 31 seconds.
Base ethernet MAC Address: 00:24:97:6e:2c:e2
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
    ether_init
    tftp_init
    boot
Loading "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 26 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15740928
flashfs[1]: Bytes used: 6858240
flashfs[1]: Bytes available: 8882688
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 present A506 7100 E8000000 A0000000 80000000 3
Radio1 present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision B0) with 25590K/7168K bytes of memory.
Processor board ID FCZ1317Q102
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.98.218
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:24:97:6E:2C:E2
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13142PXW
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FCZ1317Q102
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.864: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.480: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.066: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.154: %LWAPP-3-CLIENTEVENTLOG: Unable to open event log file flash:/event.log
*Mar 1 00:00:09.155: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)
*Mar 1 00:00:09.184: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.294: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.358: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
*Mar 1 00:00:11.358: %SNMP-5-COLDSTART: SNMP agent on host CC-P2-AP4 is undergoing a cold start
*Mar 1 00:00:11.437: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:11.615: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:12.297: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:30.265: status of voice_diag_test from WLC is false
*Mar 1 00:00:30.308: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:40.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:00:41.348: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:00:50.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:00.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:10.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:14.626: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source
*Mar 1 00:01:14.665: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.703: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:15.627: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:15.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:20.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:01:40.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:50.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:00.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:10.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:02:30.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:40.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:50.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:00.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:20.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:30.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
I was checking another thing, usually the switches we use here in my work supports a maximum of 14W per port or 15.4w, this wap is consuming 15.2w
Is this the problem??
the strange to me is that,in this same sw I have several WAP and they all use 12.2w
The device type in sw for WAP usually appears as LAP1131AG-AIR-E-K9 ... but this WAP appears as Ieee PD ...
What problems do you think is it?

Sleep light flashes 5 times - no beeps. What does it mean?

I have a white 2008 Macbook 2.4 Ghz. I recently installed 10.6 from scratch via Retail DVD and the Macbook worked fine. I updated via Software Update and installed all the updates that appeared. There was also a Firmware update to install, which I did after the update to 10.6.8.
But since then, the Macbook has serious video problems.
It boots okay, but the sequence is now:
- front sleep light flashes 5 times; there are no error beeps
- I hear the startup chime
- the Apple logo and spinning wheel appear, and bootup continues
- at the point where the screen goes blue, and would normally boot to the desktop, the screen now goes black and the Macbook appears to go to sleep
If I wait for a couple of minutes, when I press a key to wake the Macbook from sleep: the DVD spins up, the sleep light flashes 5 times, and I now see the desktop. But then the screen goes black after about 10 seconds.
Before the screen goes black, I can see that the boot seems to have completed okay. I have a Wifi connection and the date and time are correct.
If I go really fast, I can move the arrow to the Apple icon in the top bar and choose Shut down or Restart.
I can boot from the internal HD, an external FW HD and an Install DVD.
I can hold down the Option key and I get all the bootable volumes to boot from. I can choose any of them, then start the boot process, but at the same point - the blue screen - the screen goes black and the Macbook goes to sleep.
The Macbook works perfectly fine when connected to an external monitor. In the Display preferences, only the external monitor is available. The Macbook monitor is not listed. As well, iSight and Photo Booth report that no camera is connected.
I've found some info on the Apple site re. the 5 sleep light flashes, but it only refers to the Macbook Air, and indicates a problem with the battery.
Has anyone seen this problem with the Macbook?

From EZ Jim's link, there was another link to this info at the Apple site, re. Power on Self-Tests:
The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
As I wrote, I don't get the Error Beeps. I've had these on other Macs, so I know what they are. Here, I only get the LED flashes.
What is interesting above is that they say that the Power LED will flash a corresponding number of times (as the beeps) PLUS ONE. In my case, then, if I got 5 flashes, then might it mean NO GOOD BOOT IMAGES IN THE BOOT ROM?
Anyway, it doesn't seem to have the flashing LED problem any more. No idea where to go from here.

Have a nx9600 and when it tries to reboot, the hard drive light comes on, the 2 lock lights flash

At boot, the hard drive light comes on, the 2 lock lights flash simultanously (A and 1 ) , 2 of the 3 fans come on, then it appears to turn off. It will sit in a loop through the reboot process until the power and the battery have been removed.
Have replaced the drive and the center fan. The replaced fan is new and an HP fan. When I have been able to get it to boot , loaded windows and linux on the new drive.
If it sits long enough and you pray it may reboot. Once I turned it upside down and it rebooted.
Have had the system up and running for hours with no problem, then have to reboot or a shutdown and won't reboot.
Suggestions ?

Install or Reinstall Mavericks or Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.

Grey screen, mbp not starting up, flashing sleep light & 3constant beeps

hi there i tried to restart my mbp this am and it would not power up, I get a grey screen, three loud constant beeps and flashing sleep light in time to the beeps!
THe HD sounds as if it is starting up, I hear the whirring then nothing but this annoying been and a stoney grey screen!
please help!!
xx
Fran

Do you have upgraded ram in your MBP? I believe that 3 beep signifies that your computer has failed ram tests on both banks of ram.
Some RAM may appear to pass the Power-On-Self-Test (POST) but still cannot be used by the operating system. In this case, the computer will display a gray screen, sound three tones and blink the power LED on the front of the computer three times, pause, and repeat the blinking until the computer is turned off.
The solution to both of these situations is to first re-seat the memory and test the computer again. If the memory fails the POST test again, try memory that has been verified to work correctly on another system (i.e., "known-good") or order new memory from the Apple Store.

Broken Charger, Flashing sleep light, etc

Hi this is my first Apple Product and my first issue so I hope you guys can help me with it.
I was given a 15-inch Macbook Pro July 2010 as a gift for making it to college. Last night, after opening up my Macbook from a sleep state with the adapter plugged in, the charger light suddenly goes out. I've tested the charger and determined that it's dead. At the time, I was somewhat peeved but I understand that electronics can be erratic at times and I wasn't in dire need of it. This afternoon however, I forgot that the adapter didn't work so while working on homework it suddenly crashes. I ask my roommate if I could borrow his charger (knowing that it works on my MBP since I tested it the previous night) and when I attempt to turn it on I notice that the charging light is still green, the computer has its sleep light flashing at regular intervals and (I assume) the hard drive starting then dying.
So in summary: charger dies after waking MBP from sleep --> computer's battery goes to 0 charge --> roommate's charger that previously worked fine stays green but doesn't start/sleep light blinking/hard drive noise.
Any help would be appreciated since I have some unfinished homework.
Thanks

If a SMC reset does not bring life to your MBP, bring it in for service:
http://support.apple.com/kb/ht3964
Ciao.

Airport Extreme Utility not recognizing base station; flashing amber light

I'm using a PC with a Linksys PCI W54G PCI Adapter card. My Bellsouth DSL connection has worked fine using a direct ethernet connection. I'm now trying to setup a new Airport Extreme for wireless, but cannot get the utility to recognize the base station. The amber light flashes. I have tried resetting and rebooting. Still nothing. What am I doing wrong?

ESSENTIAL MAINTENANCE
1. Repair Permissions - /Applications/Utilities/Disk Utility.app. Start Disk Utility, select your HD and click on Repair Permissions. When finished, quit Disk Utility and then restart your computer.
2. Reset PRAM - hold down Option-Command-P-R keys when starting until you hear the startup chime a 2nd time.
3. Safe Mode Startup - hold down the Shift-key at startup until you see the login screen. When logged-in, then go to System Preferences/Network/AirPort
- click on the 'Network Name:' roll-button, select 'Join Other Network...', enter 'Network Name and select the security type you are using, and finally, enter your Password and click 'Join'.
If ISP uses DHCP:
- click on 'Advanced', TCP/IP and confirm that 'Configure IPv4:' is set to 'Using DHCP', click 'OK'.
- click the 'Apply' button and exit System Preferences.
REBOOT AIRPORT HARDWARE
1. Turn power off to ISP modem and AirPort Base Station, and shutdown computer - leave power off for 10 minutes.
2. Turn on modem and wait for it to complete its test cycle. Then turn on the AirPort Base Station.
3. Turn on computer and select your wireless network using the AirPort status menu in the menu bar. Then check if AirPort Base Station appears in AirPort Utility.
4. If AirPort Base Station is not seen in AirPort Utility, quit AirPort Utility and turn AirPort Off using the AirPort status menu in the menu bar. Wait 30 seconds and turn the AirPort On again.
5. Check if AirPort Base Station appears in AirPort Utility.

Hp officejet pro 8600 flashing all lights

Flashing all lights until I press the power button. I notice it will not happen if I disable the wireless icon.

Hello @hmgm123,
Welcome to the HP Support Forums!
I understand that you're encountering a blinking light state on your HP Officejet Pro 8600 e-All-in-One Printer. I would like to assist you today with resolving this issue. Now you indicate in your post that the flashing lights occur until you press the power button and this issue doesn't appear to occur if you disable the wireless. Now just to clarify, after about 5 minutes or so your printer is designed to go into a power save sleep mode state. When this occurs you will see a flashing power button. However, when you print to you printer the printer will automatically wake up for you and print the job. At the very moment the printer awakes from sleep mode the green power light will return to the normal solid state. With that being said, the blue wireless light will flash if the wireless is enabled but your printer is not connected to a wireless network. This blinking wireless light indicates that your printer is searching for a wireless network to connect to. The light will remain Off if the wireless feature is disabled if you are not using it. The wireless light will remain solid if you are utilising the wireless feature and the printer is connected to a wireless network.
With all of that being explained, does this normal blinking light behaviour match what is occuring on your machine?
Here's more information: What is Sleep Mode?
If not, when exactly does the flashing light state occur?
I look forward to hearing from you!
X-23
I work on behalf of HP
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

Thanks for your response
Let me give the history - I started with an Apple Express being fed thru a D-Link EBTR 2310 cable Router from an RCA DCM315 Modem (Pure). Comcast service all the way.
Got the 1st generation TC in 2008 and merely replaced the Airport Express with the TC. Worked ok
A year or two ago I did try removing the modem and feeding the TC directly from the modem. Resulted in the same condition I have now - Continuous flashing amber on the TC. So I put the router back in the chain.
Some time later, at the recommendation of a Comcast rep, I replaced the router with (a Belkin F5D 5231) to see if speed and dropout problems would be improved. I thought it helped some at the time but now I am not so sure.
Last week I decided to see if a new modem would help with download speeds. So I got another pure cable modem (Motorola SB 6121- high on the Comcast recommended list).
Got up and running easily with Comcast help and with the modem connected directly to a computer.
Next I put the TC in the link and again could not get past the TC continuing to flash amber. Although I did get connected to the internet with this configuration I lost connection two both of my printers - one connected by USB and the other wirelessly to the TC. Again everything works fine when I put the Belkin router back in the system.
However with the router in there, the modem shows the downstream connection to be 10/100 ethernet speed. (Modem light changes color for indicating speeds.}
I have gone thru all of the combinations of powering down/ up, but all stays the same.
I can live with what I have but something still doesn’t seem right.
Thanks again

2950 appears dead System Light Flashing stat light stays on

Similar Messages

Maybe you are looking for