2960 and configuring with a browser

I am thinking about buying a 2960. I am not good with command line can I do advanced configuring such as traffic policing and Qos with some type of Cisco admin software?

As a matter of fact, you can use Cisco Network Assistant (CNA) with the 2960. CNA is a free GUI-based tool that allows you to perform fairly advanced configuration including QoS.
Here's a link with more info on it:
http://www.cisco.com/en/US/products/ps5931/products_data_sheet0900aecd8034fbf1.html
Hope that helps - pls rate the post if it does.
Paresh

Similar Messages

BPM 11g install and configuration with Webcenter

Hi,
I am new to this BPM so need some help in installation. Where can I download the latest version of BPM 11g and for installating it what steps do I need to follow. Also I need to integrate Webcenter also so for webcenter integration what do I need to install and configure with BPM 11g.
Do I need to install webcenter full suite for integration with BPM and if so can I install both BPM and webcenter in one home iteself. Where can I find some documentation arround installing BPM and configuring with Webcenter.
Thanks

Hi,
Need some info on the install I have to install both SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3 on the same box. I have installed the SOA BPM 11.1.1.3 but wanted to find out what is the best option of installing Webcenter 11.1.1.3 as I need to integrat SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3. Here is what I think are the options but don't know which one should I go for or is there any other option but the fact is I need to install both on the same box.
*1. Should I install Webcenter in a separate HOME in doing so I will end up installing weblogic again and then install webcenter. Will endup having two ORACLE HOMES one for SOA BPM and one for Webcenter.*
*2. OR should I install Webcenter in the same home as SOA BPM and create a new domain in doing so what happens to some of the components that are installed when installing SOA BPM.*
*3. OR should I just extend the SOA BPM Domain and have both SOA BPM and Webcenter installed in the same domain. I believe this will only add the webcenter components but don't know if there are any issues.*
And help is really appreciated..
Thanks

Flash doesn't work and work with another browser!!

''locking as a duplicate of - https://support.mozilla.com/en-US/questions/900202''
Flash doesn't work and work with another browser!!.
The message is " An error occurred, please try again later" just with youtube. Other sites work. Another browser works with youtube!!

Whay do you mean "difficult with the camer?"
Two things that might help. Reset all your settings and reset the phone. Use the Settings app to reset all settings. Settings > General > Reset > Reset All Settings Then reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. See if that helps.

Allowing a website to expand and shrink with a browser

I am working on a website and wanted to know how to let a
logo with butts right up to the left side of the screen but can
also shrink and strectch with the browser so it will always start
and end at the bottom and top of the browser.

Ask your boss, "How high is up?"
The notion that all the space on a page has to be filled is a
hallmark of a
rookie designer, whether on paper or screen. Your boss needs
to hire someone
with professional web design skills and then follow what he
or she suggests.
A boss who dictates things he or she has no knowledge of or
experience in is
going to end up with a disaster. The page you have created so
far is doomed
to failure. 20 layers?
(Please show this message to your boss & suggest he or
she log on here and
learn the realities of web design.)
Walt
"margin_walker" <[email protected]> wrote in
message
news:f8or9s$4hn$[email protected]..
> this is the site so far
http://www.trinity3marketing.com/
>
> i would like the left icon to stretch to the bottom but
also adapt to the
> window size i guess is what i wanted to say. my boss is
very adamant about
> that,
>

Problems with album artwork and configuration with the last iTunes version

hello,
Since the latest version of iTunes, it is not possible to remove the manually added albums illustrations. The method is to put it more laborious because it is necessary that the image is on the computer. We can not make a copy and paste from Google Image to insert an album artwork in the song changes tab.
Also when synchronizing to an Ipod Touch 5 or 6+ iPhone, illustrations may appraissent where its just the element that is not imported.
Thank you for your help

The new iTunes 12 Get Info dialog lacks right-click context menus (at least for now) but it still accepts most standard keyboard shortcuts and drag & drop actions.
Delete Artwork
On the artwork tab of Get Into, tap the image in question, use Backspace or Ctrl+X. Delete doesn't work.
Or, tap the image at the top left of Get Info, this time use Backspace or Delete, it is Ctrl+X that doesn't work.
Add Artwork
Select artwork, press Ctrl+C to copy, tap the centre of the Artwork tab, press Ctrl+V to paste.
Or, select artwork, press Ctrl+C to copy, tap the small image area at the top left, press Ctrl+V to paste.
Or, you can drag & drop to, or sometimes from, the same locations.
You can also copy artwork from the Get Info dialog to Windows Explorer with the keyboard shortcuts.
If the source image is on a web page right-click and use Copy Image rather than copy. (With Chrome I get a one pixel wraparound so tend to go for a temporary local copy anyway - not sure whose bug this is, but it isn't new.)
If you have multiple images embedded drag the one you want to be the primary artwork to the leftmost position.
Replace/Remove All Artwork
The top left image box can be used to add or delete art from multiple tracks. In either case all existing artwork in all tracks is replaced/removed.
Old Style Get Info Dialog
Select some items, right-click, hold down shift, then click Get Info from the context menu. (Use alt/option on a Mac)
tt2

Install and configure Oracle AS 10g Business Intelligence Comp with SSO

Hi,
Present setup:
We have a Red hat Linux 3.0 ES (update 4).
Netgrity from Site minder installed over windows server for signle sign on.
Oracle 9i release 2 database on a separate Windows server
What i need:
I want to install Oracle Application Sever Business Intelligence Components 10G over the linux and configure with Netegrity Single Sign on. I am not clear what is the installation process and what is the sequence of installation and configuration.
Can anyone help me with the Installation process and sequence.
What should be the sequence is it like below ?
1) first install the Oracle AS 10g Infrastructure over the Linux
2) Secondly install the Oracle Application Sever Business Intelligence Components 10G and integrate with Infrastructure
3) Configure with SSO
or only install the Oracle Application Sever Business Intelligence Components 10G and Configure with SSO is enough ?
Any help in the installation process and sequence of instlallation and how to configure for external single Sign on.
Thanks..

When you want to have SSO you definitly need the infrastructure as the SSO is managed in there.
So first install the infrastructure, then the middle tier (BI components) and then configure the SSO for the BI components.
When this is up and running you have to configure the integration with the SiteMinder. Check out the OID admin guide and the SSO admin guide.
cu
Andreas

How to get my text and graphics to scale with the browser dynamically?

Hi there!
I've run into an issue where, with my design - I'm trying to get text and graphics to scale and move with the browser as someone adjusts it. (As opposed to it moving and falling apart as the browser window gets too small.)
http://www.richardsuchit.com is where it's posted at the moment.
I'd it to maintain it's position in the center of the browser window no matter how small or large, just to adjust in size, rather in position. I wonder if this is possible?
Looking forward to your answers! Thanks.
-Richard

Hi
Here is a sample file of text that re-sizes according to your window size.
https://www.dropbox.com/s/z7hqxejysuxs597/Sample.zip
Regards
Susanta Kumar Muduli

ISync Palm Conduit cannot be configured with the HotSync Manager UPDATE

First, I apologize for the SPAM-like posting of the material below in the existing threads regarding this issue. It is—unfortunately—the most effective way to garner the attention of earlier posters and gather this information.
Apple continues to investigate the issue, and needs this information to isolate and identify the problem. It is characterized by the apparently successful installation of the bundled iSync Palm Conduit using the Enable Palm OS Syncing… option in iSync 2.4 with either Mac OS X 10.4.9 or 10.4.10, but with the result that this conduit—normally visible in and configurable with the HotSync Manager—cannot be seen and therefore not configured.
In order to help Apple software engineers isolate and identify this issue—if you are affected by this specific issue—can you please provide the precise build number for the operating system on the machine that exhibit this problem?
To do so, select About This Mac from the Apple menu, and—beneath the Mac OS X label—press the Version 10.4.9 or Version 10.4.10 label. That value will change to something like 8P1xxx. Please respond to this message with that build number, the version of Mac OS X 10.4.x you have installed, and the last three digits of your machine serial number.
Thank you in advance for providing this information.

First, I apologize for the SPAM-like posting of the material below in the existing threads regarding this issue. It is—unfortunately—the most effective way to garner the attention of earlier posters and gather this information.
Apple continues to investigate the issue, and needs this information to isolate and identify the problem. It is characterized by the apparently successful installation of the bundled iSync Palm Conduit using the Enable Palm OS Syncing… option in iSync 2.4 with either Mac OS X 10.4.9 or 10.4.10, but with the result that this conduit—normally visible in and configurable with the HotSync Manager—cannot be seen and therefore not configured.
In order to help Apple software engineers isolate and identify this issue—if you are affected by this specific issue—can you please provide the precise build number for the operating system on the machine that exhibit this problem?
To do so, select About This Mac from the Apple menu, and—beneath the Mac OS X label—press the Version 10.4.9 or Version 10.4.10 label. That value will change to something like 8P1xxx. Please respond to this message with that build number, the version of Mac OS X 10.4.x you have installed, and the last three digits of your machine serial number.
Thank you in advance for providing this information.

How coherence 3.5 can be configured with weblogic

Hi Guys,
Can anyone help me, how to setup the coherence and configure with the weblogic server.
Thank you.

Basic setup is very simple. Include coherence.jar(coherence/lib/ ) in WebLogic system class path in startup script.
You can also refer here.
http://coherence.oracle.com/display/COH35UG/Installing+Oracle+Coherence
jayesh@yagna

Need documentation on IXOS Archive Administration n configuration with SAP

Could someone send me some step by step documentation on IXOS Archive Administration and configuration with SAP. Would be really appreciative cause i need to start this work immediately in my company.

Hi
This is a Link with all IXOS documentation on Sap Market place
https://websmp106.sap-ag.de/~form/sapnet?_SHORTKEY=01100035870000717302&_SCENARIO=01100035870000000202&_OBJECT=011000358700001866282008E
It can be found on http://service.sap.com --> Release and Upgrade Info --> Installation and Upgrade Guides ---> SAP Solution Extensions -
> SAP Archiving by Open Text
Greetings
Jose Luis Valverde

Essbase configuration with weblogic application sever..

Hi dear all....
I have to install Essbase server and EAS on one server ..and configure with application server weblogic9.2 which is installed on another server..
How can i deploy EAS to application server (weblogic) which is on another server...

FIrst of all u should have firewall open then
if SSL is installed and should be configured while configuring
give the port number while config
i think these will help u

How to install,configure and work with omniportlets

Hi,
What are the steps i need follow to install and work with omniportlets.
What are the softwares in need install. Please give required steps.
I downloaded.
1.PDK-Java software, PortalTools (OmniPortlet & Web Clipping), and common libraries
2.Download the preconfigured OC4J.
Is there any additional softwares needed.
I should install Application Server 10g?
I have to create some demos using omnipotlets which are given in the page url:http://www.oracle.com/technology/products/ias/portal/omniportlet.html
Thanks.
NR

Hi,
working with omni portlets they given two installation methods.
1. the preconfigured standalone OC4J with OracleAS PDK.
2 Iinstall OracleAS Portal as part of the Oracle Application Server release, then most of the configurations are already done.
I have
OS: Redhat Linux 4
Browser:Mozilla firefox 1.5.0.3
database:Oracle10g.
I performed 1 method but while openig link http://172.16.122.249:8888/portalTools/omniPortlet/providers/omniPortlet
i am getting the error
Error occurred while rendering Provider Test Page - view the HTML source for more details
I have to create some demos using omnipotlets which are given in the page url:http://www.oracle.com/technology/products/ias/portal/omniportlet.html
what installations i need to done.
Please help me.Thanks
NR

I have LabView but I do not have the Calibration and Configuration Palette,and I could not download it, how can I download it or if i cannot,can I work with the NI-DAQ Calibration_1200?

I have read in a tutorial for the board 1200 that I can calibrate it with the Calibration and Configuration Palette in LabVIEW, but I do not have them and I could not download it to access its libraries, so I can only download the NI-DAQ software,What's my best choice and if it is to download the palette with its libraries, how can download it with them?I'd appreciate your answers

If you wish to use your 1200 device in LabVIEW, you must download and install NI-DAQ. When you install NI-DAQ, it will ask you if you would like to install support for LabVIEW. By installing this support, you will then have access to the DAQ pallette in LabVIEW. The DAQ pallette requires that you have NI-DAQ installed.
For more information on installing and using your device, you can refer to the DAQ Quick Start Guide. You can download it from:
http://digital.ni.com/manuals.nsf/14807683e3b2dd8f8625677b006643f0/0eca53fe80911b1f862568560068295d
Regards,
Erin

How to properly create and configure SharePoint 2013 Search service with PowerShell?

Hello Forum,
I have installed SharePoint 2013 across three tier servers:
WFE Server (Of course, SharePoint is installed here. Bsically this is just a Web server)
APP Server (Of course, SharePoint is installed here + Central Admin + Service Apps).
SQL Server
I now want to create and configure the Search service, obviously on the APP Server, But of course the search functionality should work correctly on the WFE server to.
I want to do this via a proper PowerShell script. I found Spence Harbar's script on: (http://www.harbar.net/articles/sp2013mt.aspx), But it has three problems, and they are as follows:
1) Spence Harbar himself literally stated on his article that this script is for: "deploying on a single server farm", But what if I have three tier servers? Could anyone please help me out in suggesting the required tweaks in the
script?
2) By default Search uses the SP_Farm account, So, How can I change the script to use other dedicated account for the search service e.g. SP_SearchAcc ?
3) How can I modify the script to specify a default Search center?
4) Apart from all the three aforementioned point - Is the script missing anything?
I would greatly appreciate your inputs - Thanks !

the only differences are where you place the components. if you are doing a small server farm with a 1-1-1, most likely you just need to change the script so that you set the index and query processing component on the front end, but the others on
the app server. just a 2 second update... just keep in mind this will work, but I am making several assumptions without any knowledge of your farm, users, capabilities.
generally, there would be more of a breakout on the topology than that, but im guessing for this farm that you wont have dedicated search servers. also, a lot depends on # users (rps really), # items in index, size of VMs (RAM for query processing,
Disk for index, etc, etc), and making sure the topology works for your particular environment and needs.
if you want more detailed topology help, which aligns as closely as possible to "best practices" (not that those exist in SharePoint, go ahead and provide the total # users, average/peak RPS for search, current index size, content source types,
VM specs RAM, CPU, #/Size of drives, HA concerns/priority (obviously isn't, since only 1-1-1)
Christopher Webb | MCM: SharePoint 2010 | MCSM: SharePoint Charter | MCT | http://christophermichaelwebb.com

I changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password

i changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password..
can anyone help me to solve this issue

i just opened my ipad, started my apple account/I.D. and realized I put the wrong e mail. I was having trouble correcting my I.D on the Ipad so I went to my laptop and make the proper changes/slash e mail address I wanted for my apple ID. I got back to my ipad and try to download an app I can't because I have to sign in my apple account and I can't because it still has the irrelivant I.D/email address..
So, i did what you said.. went to setting>app store> tapped on my e mail.. it asked me to sign in (with my invalid emails address showing). I signed in with the password I had created. It said "incorrect".. I went to reset password. I reset password, tried to sign in and it says again "unvalid password".. this is getting irritating. I have been asking and no one knows what to do.

2960 and configuring with a browser

Similar Messages

Maybe you are looking for