2960-X Stack and LMS

What are the steps to upgrade the IOS on a 2960-X stack using LMS 4.2? Can I use the .bin file or do I need the.tar file? Also, will this upgrade all the stack members or just the stack master?

By my count, you have ~100 devices in that building. I would expect many of the IP phones will have a PC attached. Why is your port count so high? 192 ports or 240 ports per the quotes seems like too many.
Also, you might want to check the 3650 switches. They are basically replacements for the 3750x with newer technology and the same price point.
It doesn't look like 3750 + 2960 makes sense. Why add another bottleneck and layer of troubleshooting if not necessary? Why not just stack the number of switches you need instead of adding a semi-distribution layer? Stacking provides much more throughput than copper uplinks. If you need more throughput to the cores, use 4 X 10G uplink interfaces.

Similar Messages

Catalyst 2960-S Stack Interface Packet Drop

Hi all!
I have a 2960-S stack with the following behavior:
SWITCH#sh int g1/0/26
     Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 12275
When I issue the show mls qos interface g1/0/26 statistics:
SWITCH#show mls qos interface g1/0/26 statistics
GigabitEthernet1/0/26 (All statistics are in packets)
dscp: incoming
0 - 4 :    35356866        0            0            0            0
5 - 9 :            0            0            0            2            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :      634354        0            0            0            0
45 - 49 :           0     49446819      0            0            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
dscp: outgoing
0 - 4 :     6835883         0            0            0            0
5 - 9 :            0             0            0     43973612      0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            1            0            0            0
20 - 24 :           0            0            0            0       204586
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           2            0            0            0            0
45 - 49 :           0      2215325       0           55            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0        29668         0            0            0
60 - 64 :           0            0            0            0
cos: incoming
0 - 4 :    35374153            2            0            0            0
5 - 7 :    50121685            0            0
cos: outgoing
0 - 4 :    12975602     43973617        85081       204622          122
5 - 7 :    47659950          105     34377016
output queues enqueued:
queue:    threshold1   threshold2   threshold3
queue 0:           0           0    47659935
queue 1:       92482     1222278    34432039
queue 2:           0           0    13178400
queue 3:           0           0    43982889
output queues dropped:
queue:    threshold1   threshold2   threshold3
queue 0:           0           0          71
queue 1:           0        1738           0
queue 2:           0           0          20
queue 3:           0           0      375553
Policer: Inprofile:            0 OutofProfile:            0
I need some help to read this output but it seems that packets are dropped at all queues, isn't it?
Any help please?
Thanks in advance!

Please post the output to the following commands:
1. sh interface G1/0/26; and
2. sh controll e G1/0/26
What kind of client is connected to port Gi1/0/26?

Adding 2960-X to 2960-S Stack

i purchased a new 2960-X switch
i would like to add it to an existing 2 switch 2960-s stack
i understand i need to downgrade the stack speed on the 2960-x with :
switch stack port-speed 10
do the IOS version need to be identical on all switches?
i have:
2960-s = 12.2(55)SE3
2960-x = 15.0(2)EX3
if they do need to be identical, whats the best way to do this?
thanks

Yes, use this command with a .tar file to upgrade all switches in the stack.
Here is an example of using the `archive download-sw` command to upgrade a stack of Cisco Catalyst 2960-S switches. Notice that the number of members in the stack is not relevant to this command. By default all members are upgraded unless the network admin uses the options to do otherwise. The TFTP IP address is 192.168.1.1, and the tar file name is c2960s-universalk9-tar.122.53.SE.tar
Switch# archive download-sw tftp://192.168.1.1/c2960s-universalk9-tar.122.53.SE.tar
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps6406/white_paper_c11-578928.html
HTH

4500-x vss MEC to 2960-x stack

Building A
(2) 4500-x VSS
(9) closets with 2960-x stacks
(2) Data Center N5K-C5596t
I'm having a difficult time trying to find documentation.
I have the (2) 4500-x configured with VSS and am trying to find info on connecting the 2960-x stacks.

Hi,
some info.
PAgP is supported in all platforms except the Cisco Catalyst 37xx stack configuration in which cross-stack EtherChannel (LACP) is required to have MEC-connectivity with the VSS. Because cross-stack EtherChannel does not support PAgP, it cannot use enhanced PAgP for dual-active detection. A common approach to resolve this gap in support is to use two EtherChannel links from the same stack member. This solution is a non-optimal design choice because it creates a single point-of-failure. If a stack member containing that EtherChannel fails, the whole connectivity from the stack fails. To resolve this single point-of-failure problem, you can put two dual-link EtherChannel group, each on separate stack member connected to VSS; however, it will create a looped topology. The loop-free topology requires a single EtherChannel bundle to be diversified over multiple members which in turn requires LACP.

2960S Cross Stack Etherchannel Issues

We have a stack of 3 2960S's switches connected to a Cisco 3750X via a 4 port copper Etherchannel, intermittently the users are losing connection to the internet and with a host connected to the Master switch running a continuos ping to the 3750X pings are lost, we have replaced the Master switch and both GLC-T's. We also split the stack and had a single 1Gb connection to each switch from the core, we ran continuos pings from hosts on each switch and the only one to drop pings was the one on the Master switch. Versions and configs below, any thoughts ?
Version 3750X - 15.0(2) SE4
Version 2960S - 15.0(2) SE5
Port-Channel Config 3750X in attached file called 3750x
Port-Channel Config 2960S in attached file called 2960s
Also auto QoS has been enabled on both 3750X and 2960S.
Nothing appears in the logs on both switches.

Leo/Umesh,
Again thanks for the replies, I did a continous ping from a PC connected to the switch stack to an address on the Internet, I also had a continous ping going from another client on a different switch stack to the same internet address. The PC connected to the suspect switch stack dropped about 15 pings but the other PC was fine. I've now set up two syslog servers with the stack logging to one and the core to the other, also I've changed the stack master to be the middle switch which has no up links connected to it. Customer will start monitoring on Monday.

Improve Auto-Stack and Process Collections with user settings

I have read through all of the Bridge request discussions, and encountered a few comments on the stacking process but nothing to explain my critique and feature request. My apologies for any redundancy.
Bridge CS4 includes two features that would (virtually) streamline my entire photo-organization workflow. Brilliant! Except that they offer zero configuration and my default scenario is very different from Adobe's, so these two would-be-wonderful features are pretty much useless to me, and to anybody else who doesn't happen to shoot in the way the presets are configured.
The first feature is to automatically group images into stacks, based on their similarity, exposure settings, and timestamps. Unfortunately Bridge considers no minimum or maximum amount of photos per stack, and has a fixed timestamp window of 18 seconds. I shoot everything in three-exposure bursts and sometimes multiple shots in less than 18 seconds, so being able to say "process collections in 3-item stacks only" would be absolutely perfect. For other people, being able to limit the timestamp range or other min/max exposure options would work great.
The second feature, which could save me hours every week but is equally useless, is to automatically process collections in Photoshop. My biggest ire about this function is that it completely ignores stacks that I have manually created AND stacks that were previously created using the auto-stack feature. Every time this function is run, it re-runs the auto-stack process from scratch and then delivers the collections to Photoshop. Not only is this made useless by the previously mentioned inflexibility of the auto-stack process, but even if auto-stack worked perfectly, this would waste time by doing the entire thing again and denying the user the option to review the stacks before committing to the Photoshop processing. The process collections feature would also be much improved if the option were given to process ONLY panoramas or HDR photos, or auto-detect. I have never shot a panorama in my life and I'm sure plenty of people have never shot HDR, but Photoshop isn't capable of knowing our intentions and there's no reason why we shouldn't be able to instruct it.

Agree. It is an interesting capability that falls short of being really useful. I feel like an ingrate to complain, but ...
I'd also like to see the capability to specify something than "Auto" for the panorama option. My experience is that most of my panos work best with "Cylindrical + Geometric Correction".
My experience is that once you get past 5+ images in a pano, it becomes very tedious ... and then 20+ images in rows is painful. Unlike a single image that you can quickly evaluate, with panos I find I need to make the pano to tell if it going to turn out. I have been generating smaller 1800x1200 or 1200x1800 files to speed up the evaluation process, but it is still very manual and tedious.
The Auto-Stack generates a AutoCollectionCache.xml, but I haven't found it workable to edit this. I'd like to be able to modify it to "force" my knowledge of what is in a group. It seems to check the time-stamp, and re-do the Auto-Stack, thus ignoring my changes. Sigh.

Re@lted t0 bluetooth dongle, stack and configuration.. .......

Hi to all,
Those r new or require some more info realted to STACK and statring the prohect read the following page
http://www.cs.hku.hk/~fyp05016/kyng/bt_j9.htm
This is may be benifical to u.
Anyhow, i am making the my final year project related to Bluetooth and i am trying to use AVETANA which can be dowloaded from the following link:
http://www.avetana-gmbh.de/avetana-gmbh/downloads/relicense.idmexieubncmqxqphuvrohkpjcgwbv.eng.xml
After u visit this link u will see that, avetana require three bluetooth address. I have inputed the address 22:22:22:22:22:22 ( or 22-22-22-22-22-22). I have extracted this address from start-run-ipconfig/all after i install the device dirver software "BlueSoleil_1.6.2.1" in Win XP OS. My bluetooth dongle is "ISSC Bluetooth Device" which i extracted from Device Manager (Start - Right Click My computer - Properties - Hardware - Device Manager). Moreover my VID and UID of the bluetooth dongle is "USB\VID_1131&PID_1001". I have even cheked the microsoft XP site
http://support.microsoft.com/kb/841803/
for the sake of conformation that whether my bluetooth dongle is supported my Win XP sp2 and the above VID and UID is not present there.
Now the problem is that site doesnot accept my above written address, and so i am unable to download the avetana,,,
In the end(after searching on the net) I have concluded that might the following reason may be there:
1) my bluetooth dongle is either of some local company manufacturer which is not recognized by win XP
2) i am using wrong device driver
3) i am unable to configure properly the bluetooth device.
Moreover, even after installing the device driver (BlueSoleil_1.6.2.1) i am unable to see any bluetooth icon in the Control panel so that i can see/change the bluetooth property.
Plz help me up..
and if i am thinking correct, which company dongle i should purchase or which other bluetooth stack (say like atinav, BlueCove) i should use...
I even want to know that with respect to stack (say atinav) i need to purchase the dongle or not..
moreover, i donot want to buy any stack as this is only my academic project so i donot have so much money to buy a stack (like atinav)
thx in advance..

Bluetooth forum
http://vietcovo.com http://forum.vietcovo.com

PI 7.1(dual stack) and PI 7.31(Single stack) -

Friends,
I have a proxy to proxy scenario - Proxy --> PI --> Proxy
We have two servers PI 7.1(dual stack) and PI 7.31(Single stack)
i did the development in ESR and my ESR is pointing to PI 7.1, when i execute the scenario i receive one error message "receiver could not be determined", i ensured that all my input is correct, still i get the same error message.
the expectation is my scenario should point to PI 7.31, Can some one help me where and what settings i need to make in-order to make it work.
Please Note: All my data is correct and i read some scn forums wherein they asked to refresh the cache , i have refreshed the cache also still the problem persists.
Thanks in advance!

Iñaki Vila
Communication component in ID is the same as sender side.
could you share your sender configuration?
Did you mean Tcode - SXMB_ADM and under that Sender/Receiver configuration
Krupa Rao Atluri
In ID steps are correctly defined.
I spoke to my colleague he hinted that at RUN TIME we want to point to PI7.31, he mentioned config change needed in SXMB_ADM
any further inputs from any one could be useful.

Duplicates in Stacks and other Editing in the Finder

I am a new Aperture 2 user and I am loving it so far!
What I am wondering is if there is a way to make duplicates in a stack show up in the finder? I have noticed that the only files in the finder are masters... is there a way to show the duplicates at least?
At the very least - I would like to be able to use some events as a screensaver or desktop. In sys prefrences, the album shows up, and all the edited photos appear as they should, but still - the duplicates are not there.
Do I need to un-stack the photo's to accomplish this?
Thanks =]

Two things:
1- You can't show edited versions in the Finder because they don't exist outside of Aperture (unless you've created a TIFF file by using Dodge and burn or another plugin or editor). This is why it's a non-destructive editor: your adjustments are just sets of instructions saved in an xml file and applied on the fly by Aperture when you view the picture. The only thing you can see in the Finder are your masters. If you want to use edited versions you first need to export them.
2- The iLife browser only shows files for which Aperture has created a preview. Make sure the files you want to use as screensaver or desktop pic contain a preview (try dragging it to your desktop: if the preview is there you'll see a green + sign appear signifying it'll be copied. If no sign appears, you don't have a preview). You can set Preview generation in Aperture's preferences or generate them manually.
But I'm struggling with your definition of duplicates: what exactly do you mean by that? If you're talking about different versions of the same file (with varying settings), then they're called versions. In fact the entire Aperture workflow is based on versions, stacks and picks. Duplicates would be the exact same picture, without any changes.
Not trying to be snotty here btw, just want to make sure I'm understanding you correctly!

FRM-13002 : Stacked and Tab Canvas must be created within Content Canvas

Hi,
I have a Tab Canvas with 2 pages on it.
In one of the pages the data to be displayed will be
out of the region(size or length) of that page.
I read in this forum for the same problem, the
member had suggested to use a Stacked Canvas on that
Tab page alone and enable the scrollbars of the stacked canvas.
When I drag and drop a stacked canvas on a tab page
of the tab canvas I get the following error:
FRM-13002 : Stacked and Tab Canvas must be created
within content canvas.
Any help is appreciated.
Thanks in advance
Sharath

Hi,
I am breaking my head over this.
I am still unable to solve this issue.
========The Requirement is as follows :===========
When I select a Tab Page of a Tab canvas, I get a
combo box with items in it. When I select an item from
the combo box, based on the item selected, I am
retrieveing the data from the database and displaying
it in that Tab Page itself. This data is in a matrix
format. i,e Has a number of rows and columns.
Without a Horizontal and a Vertical Toolbar attached
to the Tab Page I would be unable to view all the records
that are displayed on that Tab Page.
Any suggestions or examples is most welcome and
appreciated.
NOTE : ALso in what situations can we use a stacked
canvas, if the designer does not allow me to
use it with other canvases?.
Thanks in advance
Sharath.

PI Pipeline Doubt : Pipeline Steps in ABAP stack and JAVA stack

Hello
Can anyone please assist me with which stages steps of the PI Pipeline are executed on the Java or the ABAP stack.
Receiver Determination
Interface Determination
Message Split
Message Mapping
Technical routing
Call Adapter
Also can anyone please provide links relating to the PI architecture diagram describing it from ABAP and Java Stack Perspective and not from the Components perspective i.e. Integration Repository and Directory.
Thanks.
Kiran

Hi
Tha ABAP stack consists of the Integration Server which in turn contains your Integration Engine and Business Process Engine.
The J2EE stack contains the Adapter Engine and your IR and ID run on the J2EE engine.
Most of XI pipelines happens in the ABAP stack.
All messsages picked by the Adapter Framework running on the J2EE engine are passed to the Integration Engine, which does the routing. The mapping program again gets executed on the Java stack and the rest of the pipeline servies are executed again on the ABAP stack and so on.
Message, Java & XSLT (under Imported Archives) mappings are executed at Java stack;
ABAP & XSLT (in ABAP stack) mappings are executed at ABAP stack.
PI Architecture look threads
Architecture
/message/5802842#5802842 [original link is broken]

ABAP STACK and JAVA STACK certificates

Hi Fiends,
I have requirement in which I want to use HTTP adapter to send message and apply security certificate. I got from sdn that if I wan to use http adapter with certificate than I have to install certificates in ABAP stack.
My problem is I had one scenario in which I am using BC adapter to send message with security certificate and for that I had applied certificates in java stack and its working properly.
My question is,
Is it possible to use Java Stack and ABAP STACK together..?
I mean is it possible to implement both of the above scenario in same xi system?

Hi Soni,
You cannot use the same certifcates wihch you installed in Java stack with abap stack. You need to install separealy on teh abap stack.
For HTTP communication you dont need to install certificates. You only need when you want to use HTTPS communication. So if you want to use HTTPS communication and want to use SOAP adapter then you can use ther certifcates which is already installed on java stack. But if you want to use HTTP adapter then you need to install in ABAP stack.
Please see this hlep on how to install on the java stack and the process behind it:
http://www.i-barile.it/SDN/EnablingSSL&ClientCertificatesOnTheSAPJ2EEEngine.pdf
Also check this help:
http://help.sap.com/saphelp_nw04/helpdata/de/14/ef2940cbf2195de10000000a1550b0/content.htm
on abap stack check seshus response:
HTTPS enabling
Regards,
---Satish

Java Stack and ABAP Stack

Hi Experts,
i am now confused about these two stacks: Java Stack and ABAP Stack.
for IR objects, like DT, MT, SI, MM, SM, Action, Process Integration Scenario
for ID objects, like profile agreements, receiver determination, interface determination,
1. where are these objects stored in? Java or ABAP stack?
and i know Adapter Engine is run on JAVA Stack while Integration Engine is on ABAP Stack.
2. how do they call the objects stored in different stack during processing?

Hi,
1. where are these objects stored in? Java or ABAP stack?
These objects are basically developed on the JAVA stack, when they are activated their runtime version is created on ABAP stack, which you can check in SXI_CACHE transaction.
2. how do they call the objects stored in different stack during processing?
Runtime versions of these objects are responsible for the execution of the interfaces.
-Supriya.

Errror in RFC connection between SCM ABAP stack and JAVA Stack

Hi All
we have installed SCM Abap stack and SCM java stack on same system within single database.when i create rfc connection AI_RUNTIME_JCOSERVER from SCM Java stack to SCM Abap Stack its working fine,but when i am configuring same from SCM Abap to SCM Java using SM59 its giving error.
Error Details     Error when opening an RFC connection
Error Details     ERROR: failed to open file G:\usr\sap\SCD\DVEBMGS00\data\sideinfo.DAT
Error Details     LOCATION: SAP-Gateway on host OPS20SCD1.Octal.pet / sapgw00
Error Details     CALL: fopen
Error Details     COMPONENT: SAP-GW-LIB (ReadSideInfo)
Error Details     COUNTER: 1854
Error Details     ERROR NUMBER: 2
Error Details     ERROR TEXT: ENOENT: No such file or directory OR: The system cannot find the fi*
Error Details     MODULE: gwxxside.c
Error Details     LINE: 274
Error Details     RETURN CODE: 451
Error Details     SUBRC: 0
Error Details     RELEASE: 701
Is it compulsory to create RFC connection between abap and java installed on the same system.
plese suggest.
Regards

to configure acceptance of the ABAP (integrated ITS / WebGUI) saplogonticket on the java stack, just log into the java stack (http://FQDN:50xxx/nwa) and select configuration THe last item in the list is Trusted System... click.
on the ensuing page, click on the add trusted system button --> by querying trusted sytem.
Enter the required data on the page:
system type: ABAP
host name: FQDN
System Nr: your instance number
client (of the productive client)
and a username and pw with superuser priveliges in the system (SAP_ALL/SAP_NEW, etc).
the click next
On the final screen, click finish.
You have now SSO setup between the ABAP and Java stacks. To configure SSO to accept java saplogontickets on ABAP see:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2b0310d6-0801-0010-3185-b2371a280372
This should resolve your question.

How is the interface between the Java Stack and ABAP stack is achieved?

How is the interface between the Java Stack and ABAP stack is achieved?..Please send me the answer to [email protected]

Hi,
By interface, I assume you mean the connection between the ABAP and the Java stacks in a double stack system.
The connection from Java to ABAP is through JCo connections defined in the WebDynpro section of the J2EE start page. So Java to ABAP requests are processed through JCo.
The connection from ABAP to Java is through RFC connections defined in TA SM59. The ABAP to Java requests are processed through RFC.
Refer https://dsd.esco-salt.com/StartPage/documents/integration/3.html for detailed explanation.
The UME can be maintained in either ABAP or in JAVA depending on the persistence.
Refer: http://help.sap.com/saphelp_nw70/helpdata/en/5b/5d2706ebc04e4d98036f2e1dcfd47d/frameset.htm
Check UME data source configuration.
Some quick FAQs can be found at:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ad47eb90-0201-0010-7cb2-ddfa5ed879ec
Hope this helps.
Best Regards,
Srividya.R

2960-X Stack and LMS

Similar Messages

Maybe you are looking for