2nd Monitor Cable

Looking for a "clean" video cable for adding 2nd monitor to 24" iMac.
The back of the computer faces the world. Would like to have short
12-18" monitor cable (dreaming) and not have to use Apples adapter attached to 6' folded up vga video cable. And of course white would be nice.
Second choice would be the Apple adapter and just a short male/male vga cable.
thanks
john thorne

I don't think you'll have any luck avoiding the mini-DVI adapter, but here's
a source for male/male VGA cables in various lengths -- unfortunately,
nothing short AND white.
http://www.monoprice.com/products/subdepartment.asp?cid=102&cpid=10201
...how 'bout a soldering iron?
Looby

Similar Messages

What cable do I need to connect a 2nd Monitor from the thunderbolt port?

Hi I have got one of the brand new iMac's with thunderbolt ports - what cable do I need to connect my Imac to a 2nd display either VGA or DVI - also is there a budget version about as well as I am sure its going to cost a lot from the apple store

Thanks I understand that I need another cable and have that from when I connected my old PC to the 2nd monitor.
http://store.apple.com/us/product/MB570Z/A?mco=MTY3ODQ5OTY - is this the one I need if going to DVI
I just dont want to waste more money on a cable that says its for an imac to 2nd screen and find it doesnt fit
For info my iMAC is the latest version (27" with the 2 thunderbolt connections and 1 firewire)
Thanks

HT1338 cannot connect my MacBook Air to a projector -does not detect and 2nd monitor. I have a new Mini port to VGA cable made by apple. When I read online I see that many people have the same problem - Is this an Apple defect??????????????????

I cannot connect my MacBook Air to a projector - It will not detect a 2nd monitor or display. I am using an Apple made Mini Display port to VGA adapter. As I read online I see that many other peple are having the same problem. Is this an Apple defect!!???? If so it just burst the bubble about how great macs are. I never had a problem with that on a PC. I hope I am wrong. What can you tell me?

Hi There,
I have had the exact same issue but with a projector.
The issue lies with Mountian Lion 10.8.2.
I tried many a combination with no luck to get HDMI working.
Took my mac into the apple store and came to the conclusion it was the software, so I asked them to install 10.8 onto it (this is destructive so a backup is a must)
Bought my macbook home and voila, now displaying through my projector.
There is a small graphics update after 10.8.1 which seems to be the cause.
Hope this helps.
Thanks.

Can't run flash player in full screen on 2nd monitor

Hi all! I have a laptop with dual video displays. The main
display is the laptop's LCD and the 2nd display is a 19" LCD
connected via VGA cable. I want to let a Flash movie loop endlessly
on the second monitor while I continue to work on the laptop. When
I drag Flash Player 8 over to the 2nd monitor and start the movie,
I can hit maxmize and it will take up the entire 2nd montior as it
should...with the file options and boarder around as expected. I
then hit Ctrl-F to go full screen and it snaps directly to the
laptop's primary monitor. I tried it at work where my desktop has 2
displays and the same thing happens. I need to force Flash player
to run full screen on the 2nd monitor and cannot find a way to
accomplish this. Any help is appreciated because it's driving me
nuts. I can always make the external monitor my primary but then
the start button and all my icons move there too and that is not
acceptable. Thanx!

Seriously? No one has any thoughts about this? I can't
believe I would be the first to come across this issue.

2nd Monitor won't work

I bought a Pavillion p6210f last week with Win7 loaded to replace my Dell/Vista. I was using two monitors with a VGA port and DVI port on the old PC, so I tried plugging in the same on my new HP and the DVI would not fit. In examining the pins I found that, althought the Manual said DVI, but the plug has the pin/bar arrangement of a DVI-D. So, I bought a VGAto DVI-D adapter and everything plugged in snuggly. All pins and bar appear a match.
But, it won't work. This is what is showing
NVIDIA nForce Serial ATA Controller HP RC Mirror Driver [Display adapter]
NVIDIA GeForce 9100 [Display adapter]
Acer P241W [Monitor] (24.0"vis, s/n LB4040014320, March 2008)the one working monitor....
After hours with the 800 support and hours of reversing the two Acer monitors, the DVI-D port is simply dead. Anything plugged in to the VGA works fine, anything and any combination plugged into the DVI-D and cable switching etc. the 2nd monitor is not even recoginized. The NVIDIA control panel doesn't recognize it. The amber power light just stays that way and nothing ever flashes on the 2nd screen. That is, it is the same as not plugging in at all.
I was less than pleased when 800 tech and supervisor suggested I take it to a repair center. A week old? I have put way too much setup and data transfer into the new HP to go back to the retailer for a replacement.
Techs didn't know, but could there be a DVI-X with the same pins that also fits

Eldric, did you update to the latest video driver from nVidia? It sounds to me like a driver problem. Update and let us know if that solves your problem.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Mac Pro 3.1 (early 2008) lags since I connected a 2nd monitor - HELP!!

Hey guys,
I just bought a 2nd monitor and i have lags every 5 seconds which
last about half a second (feels like 10 or less fps during the lag).
It happens with all kinds of applications. It gets worse with multiple
applications openend at a time. The crazy thing is that it only occurs
when i start to use both monitors at the same time. When i e.g. use
Logic 9.1 and use one monitor everything runs nice and smoothely
but as soon as i move the window slowly to the 2nd monitor i can
see the window lagging while I'm moving it. This is really annoying
because it seems not every input from the mouse/keyboard gets
into the system and its not a smooth workflow at all.
I switched the monitors connections but it didn't help.
Mac Pro (Early 2008) 2.8Ghz 8-core
Snow Leopoard ( 10.6.2 )
6GB RAM (2x2gb kingston, and the usual 2x1gb)
ATI 2600XT and 3 HDD.
1 Monitor 24" LG W2452T running at 1920 x 1200
1 Monitor 22" Samsung Syncmaster 2243BW running at 1680 x 1050
I really hope that you guys can help me out with this one.
What could be the problem? The ATI 2600XT should definately
be able to handle two screens at once with such little graphics
in logic 9 ?!
I want to run Logic 9 and an analyzer software (Spectre from AudiofileEngineering)
at the same time but its not possible with the LAG.
The problem/lags also occur when i sync the monitors.
Would a 2nd graphics card be a solution? But as I said
before its not a graphics demanding application.
Is it a hardware or software problem?
Summary:
- The whole System lags (not just one monitor) when
I start to use both monitors (having application windows on both).
I've got minor lags when using only one display and leave the
2nd one with the desktop wallpaper clean.
I tried:
-using only the 2x1 GB RAM which came with the mac pro
-using only the 2x2 GB Kingston RAM
Thank you in advance for your help guys!
Rick

Hey all,
I wasn't able to fix this yet.
I did everything I can think of. I even tried to wire
one monitor with a VGA cable but it didn't help.
I even have small lags when I am moving the Safari window
between the 2 monitors. Really little lags then but they
definitely are noticeable. I can make a video of that
if that would help someone understanding.
Hope there is someone out there who can help me with this.
Thanks already for any advice!
Cheers,
Rick
Edit: Do you think a new graphics card like the ATI 4870 would
help it? But I really don't want to spend more money just to
have 2 monitors while i have already 2 dvi connections on the
ati 2600XT.
Message was edited by: RickUnique

How can i use my tv as the 2nd monitor

hi, how can i use my tv as the 2nd monitor, for example pull a video from desktop to tv for windows7, the computer is hp omni 120 all in one. because i have a cable for it that connects to the tv but i dont know how to connect the pc to the tv. i tried to go on the 'change screen resolutions' but that didnt help. thanks

Hi,
Here is it specs:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c03343048#N1221
You can only see:
Front:
1 - Screen area
2 - Microphone array
3 - Webcam camera
4 - Stand
5 - Speakers
Back:
1 - Optical disk drive (actually right)
2 - Stand
3 - Kensington lock slot
4 - Power button
5 - Memory card reader and other I/O on left side
6 - Motherboard back I/Os (specific I/Os are model dependent)
7 - Activity indicator
8 - Power connector
9 - LAN (ethernet)
10 - Four USB 2.0 ports
11- Audio port (actually left side)
Left:
1 - Hard drive activity indicator
2 - Memory card reader activity indicator
3 - Memory card reader
4 - Two USB 2.0 ports
5 - Microphone jack
6 - Audio port
Right:
1 - Optical disc drive
The only hope is "6 - Motherboard back I/Os (specific I/Os are model dependent)" area:
Please check area 6 above. As mentioned in my previous reply: Most likely your machine has no video out port.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

2nd Monitor

2nd monitor switches itself off after approximately 30 minutes and then goes on/off intermittently every 10 mins.
No particular pattern, but wonder whether heavy graphics work in Photoshop CS4 is a pointer? Unable to use the EIZO monitor for work.
All cabling good. No problem with iMac 20"
Regards

@phyly44
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

2nd monitor W2072a suddenly has no signal

2nd monitor W2072a suddenly has no signal, tried switching cables & rebooting but box comes up states Scanning then No Signal. I desperately need help since the only way I can use a computer is with 2 monitors due to a disability

Hi ToniClark,
Welcome to the HP Forums! I see that you have issues with your secondary monitor. What happens if you disconnect the first monitor that is currently work and just hook up the W2072a by itself? If it works then we know it is something with your computer system and if it still fails then their could be a problem with the monitor.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Logic always opens on 2nd monitor!

Hi,
I am using Logic Studio 9.0.1 under SnowLeopard. I have the annoying problem that my Logic always opens on my 2nd monitor, even when I create a new project.
How can I change this?
Thanks in advance.
BiTRiP

Check to make sure that your 2nd monitor is not setup as the primary monitor. I have 2 monitors as well and primary is on my left and 2nd on right. Take a look in the system pref to see if thats the case. have you tried swaping the cables on the video card?

IMac does not detect correct resolution of 2nd monitor

I am attempting to use my 42" LG HDTV as a 2nd monitor for my iMac. The native resolution for the LG is 1920x1080 but the iMac only allows me to select up to 1600x1200. It seems to think that the LG is a smaller screen than the iMac as well and my images are stretched. The monitors are also disproportionate, for example, if I expand a window so that there is an inch of space on all 4 sides on my iMac it will overwhelm the screen of the larger monitor so that only about 2/3 of the window is visible. It's as if the iMac thinks that the LG is in 4:3 display mode.
I am using a mini-DVI to VGA adapter. How can I get full resolution from my 2nd monitor?

The (analog) VGA connection is limiting your resolution. Idealy a (digital) Mini-DVI to DVI adapter and a DVI cable should allow the full resolution in Extended Desktop Mode.

2560 x 1600 is gone from my display settings (2nd monitor)

I've been running my 15" retina macbook pro for more than a year now with 27" DELL monitor and it has alway been using 2560x1600 resolution display.
In the past year i've had no issues with mirroring my screen to big screen TV using Apple TV, however today something weird happened.
As usual i mirrored my screen using Apple TV to watch some videos and i had to change some of the display settings to get the best view on my TV.
Afterwards i switched off the mirroring feature and now my 2nd monitor (DELL 27") is displaying 1920x1080 only. I looked at all my options on my display settings (using ATL+click ) and 2560x1600 is gone missing from the list. Im frustrated and couldn't find an answer to this problem, please advice.
Couple things i tried;
- restart & shutdown
- reset NVRAM & PRAM settings
- changed mini display cable with another
- reset monitor settings
Weird find:
I tried to mirrored my macbook pro to apple TV again to see the display settings. Guess what, the option for 2560x1600 is now back on the list and working (visually) just fine. as soon as i turned off the airplay display my 2nd monitor turns back to 1920x1080.
Note: the display on my retina macbook pro is working just fine, no problem at all. this is only showing on my 27" DELL U2713HM.

Hello! Just want to ask about mirroring: when you MIRROR the Retina MBP 15" to your Dell Monitor (2560x1600) : do both the MBP and Dell Monitor look sharp and crisp?
I'm asking because I'm also considering a monitor that's at 2560x1600.
Thanks so much!

2nd monitor not using all available pixels

So am I the only one having this issue? -
I have a Mac Mini that is running Windows 7 in bootcamp. I have 2 monitors. My 2nd monitor is connected with an HDMI to DVI cable. In Windows, the whole screen of both monitors is used (edge to edge, top to bottom). But when I switch over to Yosemite, my second monitor has about a 1 inch bar of black on both sides and a 1/2 inch bar along the top and the bottom. This is literally unused space.
I've talked to Apple Support several times but they don't seem to have an answer. I get transferred to someone but each time I get cut off. (so I gave up trying to fix this over the phone or on line chat). There are no features or selections in the Syncmaster to adjust this. Why does it work perfectly fine in Windows but not when I switch over to Yosemite.
Maybe this doesn't seem like a big deal but it's so frustrating that I'm actually finding myself not wanting to use the Yosemite side.
Does anybody have a solutio

Sorry:
Display TypeLCD monitor / TFT active matrix
Diagonal Size20 in
Aspect RatioWidescreen
Native Resolution1600 x 900
Pixel Pitch0.2768 mm
Brightness300 cd/m2
Contrast Ratio1000:1 / 15000:1 (dynamic)
Color Support16.7 million colors
Response Time5 ms
Horizontal Viewing Angle170
Vertical Viewing Angle160
FeaturesHDCP, MagicBright 3, MagicTune
Dimensions (WxDxH)19.1 in x 7.9 in x 14.7 in
Weight9.7 lbs
ManufacturerSamsung model 2033SW

Sanyo LCD TV as 2nd Monitor flicks to black & pops

Hey All,
2.66 Mac Pro running Mavericks 10.9. I plugged in my Sanyo DP42849 via HDMI using a(n admittedly third party) Mini DisplayPort to HDMI converter dongle. I should mention, I've never attempted to use this TV as a 2nd monitor, but I have used the same dongle and a Panasonic 1080p 42" tv with no issue (albeit not on Mavericks)
When I plug it in, if it recognizes the signal at all, it alternates between the desktop background for anywhere from 0-4 seconds, and black for 0-5 seconds. Inconsistently, sometimes there will be a signal pop coming from the TV.
Is this a TV issue? A Mavericks issue? A dongle issue? A Graphics Card issue? What's going on here?
I have tested 2 different HDMI cables (same result), but I only own one dongle.
When I go to the displays menu, refresh rate is greyed out, and changing the resolution does nothing towards stabilizing the signal on the TV.
Thanks for your help!!

Well the lcd that I provided the link for would be the production monitor to hopefully see how a television would view the finished product. I've got my eye on something like the Acer AL1916W - 19" LCD WideScreen for my widescreen #2 monitor. *just in case I confused anyone. As you suggested though, I will be researching more for the # monitor. Thanks again.

HOw to add a 2nd monitor to my DX4380- UR22

I only have my HDMI open and my monitr is an older version using a SVGA
This question was solved.
View Solution.

Hello there ArsenalOC1886!: to answer this question specfically
why not buy a cable that has the HDMI on one end{the PC} & a SVGA at the other(the 2nd monitor)
or get a HDMI\SVGA adapter at your local computer shop
with plug & play being as advanced as it is itshould work unless it's incompatible
good luck
hope this enlightens, clarifies & helps
spacechild

2nd Monitor Cable

Similar Messages

Maybe you are looking for