2nd monitor fails to work after upgrade to 10.4.6

Hi,
I have been running fine with 2 monitors until I upgraded to 10.4.6, and now my 2nd monitor is not detected (even after I click the detect displays).
Apart from the upgrade - I have changed nothing
Other Info:
GeForce FX 5200:
Chipset Model: GeForce FX 5200
Type: Display
Bus: AGP
Slot: SLOT-1
VRAM (Total): 64 MB
Vendor: nVIDIA (0x10de)
Device ID: 0x0321
Revision ID: 0x00a2
ROM Revision: 2060
Displays:
Cinema HD Display:
Display Type: LCD
Resolution: 1920 x 1200
Depth: 32-bit Color
Core Image: Supported
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Display:
Status: No display connected
Any thoughts/ideas.
cheers
-brett

Resolved:
After a few reboots and a couple of power cycles, it all just started working.
cheers
-brett

Similar Messages

  • G4 AGP Graphics - 2nd display won't work after upgrading from os 10.2

    I have a desktop G4 AGP Graphics with two displays. When I was running os 9-10.2, the second display worked fine, but after upgrading the os (now running 10.4), the second display still works, but has turned gray and pixelated.
    When I take a screen shot, the picture shows that both displays appear clear (and in color).
    Am I missing something? Thanks in advance for any suggestions

    so do you have 2 different video cards driving two different monitors? or is it One video card with 2 displays?
    the info you listed isnt very detailed but it does tell me you got an ATI video card with 16MB VRAM.
    I assume that thats the Stock AGP 2x graphics card that came the The PowerMac G4 AGP graphics model.
    why is your display set to 8bit depth? a stock 2x AGP card with 16MB VRAM should be able to support 16bit or 24bit depth even at 1024 x 768 res.
    the info says also Core image not support as well as Quartz Extreme no supported. Which is significant because it could be why the 2nd Monitor doesnt display properly with Tiger.
    under 10.2 there were less stringent requirements for driving video.
    OSX 10.4 Tiger is much more advanced OS and has higher graphics cards requirements now.
    I could be wrong, but I think you may need a newer video card that supports Quartz Extreme and Core image.
    hopefully someone else will run by this topic and offer some insight aside from my own.

  • Applications fail to work after upgrading to Snow Leopard

    I can't believe how poor a job the upgrade is! Ok, Snow Leopard installed ok and saved me a good bit of space. It also boots a lot quicker too. But.....
    ..what is the point of all of this if it no longer opens my applications without crashing every time??! I wouldn't mind if they were old but the apps are mostly the latest versions, and are even Apple products too! E.g. Final Cut Pro.
    Also, the apps that do open are now asking me for the registration codes all over again. If this was meant to happen then a heads up would have been nice
    Apple.
    I would prefer the slower Leopard with all my apps working than this upgrade where I can't do anything!
    What kind of upgrade do you call this Apple??? I hate to say it but Microsoft might well have done a better job! Will Apple be resolving these issues soon?
    Any one else having problems with applications?
    Anyone found a solution?
    Anyone know how to backout the upgrade?
    Many thanks from a very disappointed Apple fan.

    Everyone in my household who has upgraded to Snow Leopard has had the same problems with program crashes and the computer "forgetting" registration codes.
    In fact, after re-entering codes, and then upgrading to 10.6.1, we had to re-enter them again because it forgot (again) that we had bought/registered the software. It was a lot of fun digging through old emails and such looking for the codes, let me tell you.
    I'm pulling a Vista and downgrading my computer back to 10.5.x. That was stable and remembered my software, at least.

  • Streaming Audio (Radio) fails to work after upgrade to 8.1.0.52

    I just upgraded to the above-stated version of iTunes. Radio doesn't work, and nothing streams at all! iTunes attempts to get the playlist but to no avail. I have attempted this with a large number of streams with the same response.

    I'm having the same problem. I can't get anything to work that involves sound. No streaming radio, no Pandora, nothing. Just a warning that iTunes detected a problem with my audio configuration and that audio and video won't work because of it. I changed nothing but the version of iTunes I run.

  • Reports no longer work after upgrading to SCCM 2012 R2

    I upgraded my SCCM 2012 SP1 environment to R2 and reports no longer work.  I've removed the site role, waited a day, and added it.  I've also verified the account (used by the reporting site role) has access to the DB and can logon locally.  The
    problem still persists.  Here's a copy/paste of the error:
    Microsoft.Reporting.WinForms.ReportServerException
    An error has occurred during report processing. (rsProcessingAborted)
    Stack Trace:
       at Microsoft.Reporting.WinForms.ServerReportSoapProxy.OnSoapException(SoapException e)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.ProxyMethodInvocation.Execute[TReturn](RSExecutionConnection connection, ProxyMethod`1 initialMethod, ProxyMethod`1 retryMethod)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.LoadReport(String Report, String HistoryID)
       at Microsoft.Reporting.WinForms.ServerReport.EnsureExecutionSession()
       at Microsoft.Reporting.WinForms.ServerReport.SetParameters(IEnumerable`1 parameters)
       at Microsoft.ConfigurationManagement.AdminConsole.SrsReporting.ReportViewerWindowsForms.SetParameterValues_DoWork(Object sender, DoWorkEventArgs e)
    Microsoft.Reporting.WinForms.ReportServerException
    Cannot read the next data row for the dataset DataSet1. (rsErrorReadingNextDataRow)
    Stack Trace:
       at Microsoft.Reporting.WinForms.ServerReportSoapProxy.OnSoapException(SoapException e)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.ProxyMethodInvocation.Execute[TReturn](RSExecutionConnection connection, ProxyMethod`1 initialMethod, ProxyMethod`1 retryMethod)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.LoadReport(String Report, String HistoryID)
       at Microsoft.Reporting.WinForms.ServerReport.EnsureExecutionSession()
       at Microsoft.Reporting.WinForms.ServerReport.SetParameters(IEnumerable`1 parameters)
       at Microsoft.ConfigurationManagement.AdminConsole.SrsReporting.ReportViewerWindowsForms.SetParameterValues_DoWork(Object sender, DoWorkEventArgs e)
    Microsoft.Reporting.WinForms.ReportServerException
    Conversion failed when converting the nvarchar value 'XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXscrubbed' to data type int.
    Stack Trace:
       at Microsoft.Reporting.WinForms.ServerReportSoapProxy.OnSoapException(SoapException e)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.ProxyMethodInvocation.Execute[TReturn](RSExecutionConnection connection, ProxyMethod`1 initialMethod, ProxyMethod`1 retryMethod)
       at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.LoadReport(String Report, String HistoryID)
       at Microsoft.Reporting.WinForms.ServerReport.EnsureExecutionSession()
       at Microsoft.Reporting.WinForms.ServerReport.SetParameters(IEnumerable`1 parameters)
       at Microsoft.ConfigurationManagement.AdminConsole.SrsReporting.ReportViewerWindowsForms.SetParameterValues_DoWork(Object sender, DoWorkEventArgs e)
    I've tried many other TechNet solutions as well with no improvement:
    http://social.technet.microsoft.com/Forums/en-US/ae08aa43-054d-47e7-99fb-c4f101962478/reports-not-working-after-upgrade-to-sccm-2012-r2-?forum=configmanagergeneral
    http://social.technet.microsoft.com/Forums/en-US/77bad9b6-de0e-42d3-ae9f-e7c9d26b4330/reporting-error-after-upgrading-to-sccm-2012-r2?forum=configmanagergeneral
    Any other thoughts on this?

    So to be clear you have Done both the Mofcomp and Added the correct account to the Windows Authorization Access Group?
    What is version of SQL are you using?
    Is SSRS remote or local to CM12?
    What service account are you using for SSRS?
    Bases on the error message you are getting this within the console, Does the native SSRS report work? BTW I never recommend accessing the report via the console.
    http://be.enhansoft.com/post/2013/09/10/Should-Configuration-Manager-SSRS-or-ASP-Reports-be-Accessed-from-the-Browser-or-the-Console.aspx
    Garth Jones | My blogs: Enhansoft and
    Old Blog site | Twitter:
    @GarthMJ

  • Script no longer works after Upgrade to 10.4.6

    The following script worked fine using 10.4 thru 10.4.5 but no longer works after upgrading to 10.4.6.
    When I highlight a folder and then run the script the highlighted folder is moved to a specific "Achive" folder, depending on whether the highlighted folder has a ".0" or ".1" or etc in its name.
    When I run the script using 10.4.6 I get an error indicating that the highlighted folder already exists in the destination.
    Anyone else having Applescript problems with 10.4.6?
    --Bob
    tell application "Finder"
    activate
    set fname to selection as string
    if fname contains "0." then
    move selection to folder "ARCHIVE" of folder "0JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "1." then
    move selection to folder "ARCHIVE" of folder "1JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "2." then
    move selection to folder "ARCHIVE" of folder "2JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "3." then
    move selection to folder "ARCHIVE" of folder "3JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "4." then
    move selection to folder "ARCHIVE" of folder "4JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "5." then
    move selection to folder "ARCHIVE" of folder "5JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "6." then
    move selection to folder "ARCHIVE" of folder "6JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "7." then
    move selection to folder "ARCHIVE" of folder "7JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "8." then
    move selection to folder "ARCHIVE" of folder "8JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    else
    if fname contains "9." then
    move selection to folder "ARCHIVE" of folder "9JobsArchive" of folder "Archived_Files" of disk "Preflight_Only"
    end if
    end if
    end if
    end if
    end if
    end if
    end if
    end if
    end if
    end if
    end tell

    I, too, immediately started having problems with my scripts immediately after updating to OS 10.4.6. I put my scripts in "Library/Applications/..." so that the scripts associated with particular applications are available in the menu bar. I don't know if that has any bearing on the problem, but for me, it was not any particular script, but just about every one that started going funny.
    First, I noticed that my scripts would typically work right once, but fail in some odd manner the second time I tried to use one. The second thing I noticed was that the modification dates of my scripts were changing to the time that I last executed the scripts, even though I had not altered and recompiled any of them in weeks. Finally, I noticed that the scripts that were failing were ones in which I had used property statements to initialize some of my variables.
    What I think is happening is this: for some strange reason 10.4.6 is recompiling scripts every time they are run, and variables are being initialized, not to the values specified in property statements, but to whatever the variable was the last time the script ended.
    I discovered that I could prevent this from happening by (1) recompiling all my scripts to make sure all the property statements were back in effect, and then (2) setting the permissions of all my scripts to read only. This seems to prevent whatever in 10.4.6 is recompiling the scripts from doing this each time the script is run. At least, the modification dates are no longer changing inexplicably, and all my scripts are running reliably again.
    It's a bit of a pain to have to remember to reset script permissions to read/write whenever I want to make a change, and then change them back to read only before executing, but it seems to be a reliable workaround. I'd appreciate hearing if anyone else can replicate this phenomenon, or tell me if I'm on the right track.
    Jeff Johnson
    Dual 1.2 GHz   Mac OS X (10.4.6)  
    Dual 1.2 GHz    

  • Bluetooth handset not working after upgrading to 2.2.1

    I failed to get my bluetooth headset working after upgrading to 2.2.1. I have tried 4 different headsets (with different brands and models)and even bought a new one (Plantronic 640MP) and no luck also. I have also tried to hard reset and restore in iTunes but no success.
    I can successfully paired my headset with iphone 3G but no sound transmitted over. I have been using my headset flawlessly before the firmware upgrade.
    Any ideas? Thanks in advance.

    Hello.
    I´m new to iPhone and this forum
    I am having the same problem with my iPhone but I don´t know if it´s related with 2.2.1. firmware since that came on the iphone right away when I bought it.
    I can connect to handfree set and pair up fine, but no sound what so ever is passed to or from the handsfree set. The handsfree set works fine with other phones.
    I tryed restore but it didn´t help.
    I restored the iphone with itunes, the function "If you are experiencing problems ...." hit the button "Restore" e.g.:
    http://www.tzywen.com/photos/iphone/itunes_restore.png
    After that it told me to "set up my iphone" and I chose "restore from the backup of" e.g.:
    http://www.mattcutts.com/images/restore-iphone.png
    The links are not from my procedure, just something I found on the internet to describe what went on
    Did anyone find a solution for this problem?
    How often do Apple make new firmware upgrades? (hoping that will help)
    Regards Martin

  • After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working, After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working!

    After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working, After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working? Can it be recovered or a Hardware has to be replaced. I tried restoring my phone, but it did not work. Any solutions?

    alisportshots wrote:
    I have a similar problem, but after following your suggestion of deleting my iphone backup and then turning backup back on again, I needed to plug my phone into my computer to sync the backup.  I re-tried to do an icloud backup and it again told me that  "the last backup could not be completed"... since I had deleted the backup, it says the "Last backup:  never".  Ugh. I reconnected my iPhone 4S to my computer and iTunes so I could sync my phone and do a backup... it's still "waiting for sync to start"...
    For your iCloud backup, you may have an app that is preventing the backup from succeeding.  To locate which one, go to Settings>iCloud>Storage & Backup>Manage Storage, tap the name of your device under Backups, under Backup Options tap Show All Apps, then turn them all to Off (including camera roll) and try backing up again.  If it succeeds, then the camera roll and/or one of your apps is preventing the backup and you'll have to located by process of elimination. Turn the camera roll On and try backing up again.  If it succeeds, turn some of your apps to On and try backing up again.  If it succeeds again, turn some more apps to On then try again; repeat this process until it fails.  Eventually you'll be able to locate the problem app and exclude it from your backup.
    If you turned iCloud backup off and try to sync to create a backup on your computer and got a "waiting for sync to start" error, it may be caused by a corrupt backup on your computer.  You could try deleting your last backup by opeing iTunes and going to Preferences>Devices, clicking on your last backup and clicking Delete Backup.  Then try again.

  • Iphone 4 Home button not working after upgrade to OS 4.3.5

    Iphone 4 Home button not working after upgrade to OS 4.3.5.Please help!!!!!!!!

    It seems that settings of mail accounts have something to do with it. I've delete my gmail account and am now using Microsoft Exchange. It seems better, yet not perfect. The issue is definitely due to OS 4.3.1
    Apple answer is - no answer. It is a shame that the quality of their products, in terms of design and concept, is not match by a care for customers. It is not normal that I, as a customer, have to spend hours reading Apple Discussions forum to try to understand what the problem is. A little more respect for a customer that spend big $$$ buying their products wouldn't hurt.

  • IPad app no long works after upgrading to iOS 7.1.1

    iPad app no long works after upgrading to iOS 7.1.1

    Did you try deleting then reinstalling the app?  Sometimes developers will need to update their apps for compatibility.  If it still doesn't work after reinstalling, wait a few days to see if an app update becomes available.

  • File- Export not working after upgrade from 11i to R12

    Hi,
    File -> Export not working after upgrade from 11i to R12.1.3 in few systems. Can you please let me know what could be the issue.
    If export record count more than 200 it is working fine in all the systems and if change the profile option "Export MIME type” value to ‘text/tab-separated-values’ from application/excel also it is wokring.
    Thanks and Regards,
    Jagadeesha

    Enabled the FRD. Below are few last lines. Can you please let me know what i can in this log file contents.
    In Argument 1 - Type: String Value: global.frd_debug
    Executing GET_ITEM_PROPERTY/FIELD_CHARACTERISTIC Built-in:
    In Argument 0 - Type: Integer Value: 196613
    In Argument 1 - Type: Number Value: 54
    Out Argument 0 - Type: String Value: 12
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: Entering app_menu.set_prop.
    In Argument 1 - Type: String Value: global.frd_debug
    Executing FIND_MENU_ITEM Built-in:
    In Argument 0 - Type: String Value: FILE.EXPORT
    Out Argument 0 - Type: Integer Value: 19
    Executing GET_MENU_ITEM_PROPERTY Built-in:
    In Argument 0 - Type: Integer Value: 19
    In Argument 1 - Type: Number Value: 79
    Out Argument 0 - Type: String Value: TRUE
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: Completed app_menu.set_prop.
    In Argument 1 - Type: String Value: global.frd_debug
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: Completed app_synch.menu_toolbar_sync. Event is WHEN-NEW-ITEM-INSTANCE.
    In Argument 1 - Type: String Value: global.frd_debug
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: GLOBAL.APP_CUSTOM_MODE
    Out Argument 0 - Type: String Value: NORMAL
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: GLOBAL.APP_CUSTOM_MODE
    Out Argument 0 - Type: String Value: NORMAL
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: NULL
    In Argument 1 - Type: String Value: GLOBAL.OUT
    Executing USER_EXIT Built-in:
    In Argument 0 - Type: String Value: FND GETPROFILE NAME="UPK_RECORDING_ENABLED" FIELD="GLOBAL.OUT" N
    FNDCPVCM, 11, Built-In, Entry, 316509814, USER_EXIT
    FNDCPVCM, 11, Built-In, Exit, 316509814, USER_EXIT
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: GLOBAL.OUT
    Out Argument 0 - Type: String Value: N
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: system.current_form
    Out Argument 0 - Type: String Value: FNDCPVCM
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: system.current_block
    Out Argument 0 - Type: String Value: MASTER
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: system.current_form
    Out Argument 0 - Type: String Value: FNDCPVCM
    Executing NAME_IN Built-in:
    In Argument 0 - Type: String Value: system.current_block
    Out Argument 0 - Type: String Value: MASTER
    Executing GET_APPLICATION_PROPERTY Built-in:
    In Argument 0 - Type: Number Value: 75
    Out Argument 0 - Type: String Value: IHR40P
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: Completed call_all_libraries. Event is WHEN-NEW-ITEM-INSTANCE.
    In Argument 1 - Type: String Value: global.frd_debug
    Executing COPY Built-in:
    In Argument 0 - Type: String Value: Completed app_standard.event. Event is WHEN-NEW-ITEM-INSTANCE.
    In Argument 1 - Type: String Value: global.frd_debug
    FNDCPVCM, 10, Prog Unit, Exit, 316509814, /FNDCPVCM-3/P45_30_DEC_201223_28_33
    FNDCPVCM, 9, Trigger, Exit, 316509814, WHEN-NEW-ITEM-INSTANCE
    FNDCPVCM, 8, Prog Unit, Exit, 316509814, /DMU-4/P8_30_DEC_201223_23_12
    # 15 - FNDCPVCM:MASTER.USER_CONCURRENT_QUEUE_NAME.1359399301498413820
    WINDOW FNDCPVCM PROGRESS_INDICATOR RESIZE 4198 1500 3
    # 16 - FNDCPVCM:MASTER.USER_CONCURRENT_QUEUE_NAME.1359399301512613925
    WINDOW FNDCPVCM PROGRESS_INDICATOR RESIZE 4198 1500 3

  • Ipohone 4 hotspot not working after upgrading to ios7.1 ?

    my ipohone 4 hotspot not working after upgrading to ios7.1 but my some friends having iphone 4s its works fine and those having iphone 4 it's not working although we all have same operator and same operating system (i.e ios 7.1).I think this is problem only  with iphone 4 users with ios 7.1 , so apple plz fix it in ur next update.

    You don't like the answer?
    Again it's not a bug, use a supported carrier if you want Personal Hotspot.
    Read the list one more time, if carrier is not on the list, IOS7.1 patch the loophole.
    Message was edited by: ckuan

  • Web Service is not working after Upgrade SAP EHP6

    Hi ,
    Recently we upgraded SAP ECC 6.0 to EHP 6.
    We have a custom web service which is consumed in  .NET Application to get the Sold To from Sales Order.
    the service is working perfectly before upgrade and it is not working after upgrade to EHP6.
    When I tested the Service in WS Navigator in SAP, it is working fine.
    We raised a message to SAP and SAP analyze the Traces and confirm that the HTTP Request Header coming from .NET application is not having User ID and Password , so it is throwing exception from SAP as unauthorized.
    But in service it is configuration as basic authentication and log on using user id and password and .NET application is calling service by passing user ID & Password.
    Customer is not happy as it is working before Upgrade and SAP confirmed every thing fine in SAP, but the service is not working.
    we did the below steps.
    Regenerated the configuration
    Re imported the Certificates
    Activated the service in SICF.
    Please let me know if anybody have same problem or if any steps we are  missing.
    thanks.
    Uma

    after changing the .NET Application , Service is working fine.

  • Safari and app store fail to work after installing Maverick, what can I do?

    Safari and app store fail to work after installing Maverick, what can I do?

    Disk Utility (Applications - Utilities - Disk Utility) Repair Disk Permissions 2x. Then restart in Safe Mode and try both apps. Restart normally and post results.

  • IPhoto no longer work after upgrading to Mavericks.

    My iPhoto will no longer work after upgrading to Mavericks. iPhoto will not update. How do I fix this?

    kmg55 wrote:
    Just upgraded and Iphoto will not work,
    Check that iPhoto is v9.5.1 (In Applications, highlight iPhoto, and ⌘I)
    If it is v9.5.1, then hold option-command and click the iPhoto icon and go through the repair steps.

Maybe you are looking for