3.1.3 software update has made my iPod stop working correctly

I have a 2nd generation 16 GB iPod touch. I purchased the 3.1 update when it came out. I had some problems with my iPod after that update, but these problems were resolved when the next update came out (3.1.2 I think). Last week I did the next iPod update-3.1.3. Now my iPod is worse than before. My movies and podcasts won't download from my iTunes library, sometimes when I sync my iPod, it appears there is no music or anything on it (which was what happened after the first update). However when I go into "Settings", it says it has no songs, but all the capacity is all used up. I have to go back in to sync again, but i might have to do this 3 or 4 times before it puts my songs back on my iPod. I'd like to know how to uninstall the last update i did and just go back to the 3.1.2 version. Or if anyone knows what I should do please let me know. Please.....this is so aggravating. I wish I had never done this last update!

Just plug it into your computer and restore it through iTunes. You can try restore from backup first and, if the problems go away, then you are done. If not, restore again and select restore as new. You can resync all of your content when done.

Similar Messages

I get an error message saying 'An error has caused Photoshop to stop working correctly. Windows will close the programme and notify you if a solution is available'. I have had no notification. My old Photoshop CS5 works fine, but as I'm paying for CC2014

I get an error message saying 'An error has caused Photoshop to stop working correctly. Windows will close the programme and notify you if a solution is available'. I have had no notification. My old Photoshop CS5 works fine, but as I'm paying for CC2014 I would like to use it. I have tried renaming the 'sniffer' file to 'snifferold' as bobmiller4002 suggested but the problem is not resolved. Lightroom works fine.

Hi Nancy,
             I'm not sure I have the answers to all your questions. Although I use Photoshop and Lightroom extensively, I'm not a 'techy'.
My system;
Packard bell imedia S2885
1TB hard drive
500G RAM
Windows 8.1   64- bit
Intel core i5 4440
If I open Photoshop cc14 without opening any image, I still get an error message that reads: 'Photoshop has encountered a problem with the display driver, and has temporarily disabled enhancements which use the graphics hardware'.
There is also a link to the Adobe help site, but I'm not sure exactly what I should be downloading from there.
         Thanks,
                    Dan.

After Software Update 2007-004 airport card stopped working after wakeup

Hi,
I have a powerbook G4 - DVI running 10.3.9. After I have installed Software Update 2007-003, when my computer goes to sleep and then wakes up, airport card stops working. I had to open the back of the computer, unplug and plug the airport card, then it starts working again. But next time the computer goes to sleep, it stops working again.
Does anyone have a similar problem? Any work arounds?
Thanks in advance.
Also following is the logs from Software Update. Looks suspicious:
Mac OS X Version 10.3.9 (Build 7W98)
2007-04-28 18:56:03 -0400
2007-04-28 18:56:03.190 loginwindow[181] FSResolveAliasWithMountFlags returned err = -43
WirelessScan timeout waiting for first scan result
WirelessScan timeout waiting for first scan result

Deleting AppleAirPort2.kext solved the problem for some...
http://discussions.apple.com/thread.jspa?threadID=934370&tstart=0
While others had to rollback the AppleAirPort.kext to version...
http://discussions.apple.com/thread.jspa?messageID=4310165&#4310165
Installing the Security update 1.0.1 from 5/01/2007 helped others. Reapplying the Combo Update again helped a couple of people.

Mac 10.5.7 update has made golive 9 stop rendering css in layout view

Has any one else on Mac with the mac 10.5.7 update have new issues with golive 9 not rendering css in layout view. It works still in pdf preview and if I boot to 10.5.6 all is normal again. Also in the live rendering engine it works as well...just not in layout view- its very disconcerting. Any workarounds? anyone else with this issue?
thanks
Adam

I have been using an external CSS file simply for defining font styles
site wide. The rendering of them on screen in layout view is now just
the plain default font prior to showing the CSS altered version of it.
Sorry, I'm not sure I understand what you mean here. You mean it shows your text in the default and *then* renders it correctly using the CSS after a delay?
I tried torching the prefs...perhaps I did the wrong file...what file is to be deleted?
~/Library/Preferences/Adobe GoLive 9.0 Prefs
~/Library/Preferences/Adobe/GoLive/Settings9 (a folder)
~/Library/Preferences/com.Adobe.GoLive.plist
Move them out to, say, the Desktop. If they are not the cause of the problem, put them back replacing the newly-created versions.
I cloned my os prior to the update and all was fine. Rebooting to clone
css renders normal...but in 10.5.7 its not rendering in layout view.
I'm not seeing the same thing here with GL9/OS X 10.5.7, so it may be its something specific to your particular update. You might also want to consider doing a re-import of the site to recreate the site file and see if that helps.
John

How do I know if the Maverick software update has been installed on my mac?

How do I know if the Maverick software update has been installed on my mac?

It will not download if you already have it.
Just to be 100% clear …
Look in /Applications for "Install OS X Mavericks"
Use the Finders Go menu > Applications. To open it.
You may have an Applications folder in your Home directory too, it shouldn't be in there but it is possible.
Also try Spotlight to see if it can find that filename.
Can you also tell us what system you have?
Apple menu > About this Mac > more info button… What is the Model (under the Overview tab).
10.9 doesn't install on all systems, so it could explain why you can't get it, however it usually displays a dialog stating that fact.

Recent iOS update has made my iPad 2 unusable. The screen locks up. It's very laggy and web pages do not load correctly. Is there a fix for this or are they even working on a fix.

Recent iOS update has made my iPad 2 unusable. The screen locks up. It's very laggy and web pages do not load correctly. Is there a fix for this or are they even working on a fix.

Try some basic troubleshooting:
(A) Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
(B) Try reset all settings
Settings>General>Reset>Reset All Settings
(C) Setup as new (data will be lost if you do not have backup)
Settings>General>Reset>Erase all content and settings

Software Update has broken my system

Software Update has broken my system so that I can no longer restart or shutdown normally. All attempts to restart or shutdown hang the system with a grey screen and a Software Update menu on the menu bar. The menus can be pulled down, but the menu items, like "restart", are not functional. I have to use the control/command/power keys to force a restart, and then command-R after the chime to get to a screen where I can shutdown.
I have just done a complete reinstall of the operating system (10.7.5), with no change in this behavior. I have also tried to do a manual installation of the latest security update, but after hitting the restart button, the same Software Update screen appears whether I have actually used Software Update or not. How do I go about nudging my system out of this behavior?

The startup disk may need repairing.
Launch Disk Utility located in HD > Applications > Utilities
Select the startup disk on the left then select the First Aid tab.
Click: Verify Disk
If repairs are necessary, restart while holding down the Command + R keys so you can access ML recovery / Disk Utility. OS X: About OS X Recovery
If the startup disk does not need repairing, start up in Safe Mode
Keep in mind a Safe Mode boot takes longer than a normal boot so be patient. When you're in Safe Mode you should see Safe Mode in red top right side of the desktop.
From there click the Apple menu icon top left in the screen. Select Restart from the drop down menu.

HT6114 My iMac seems to have frozen during the update- how long should I expect the update to take? The 'installing software update' bar is still showing itself working but has been stuck in the same position for over an hour.

My iMac seems to have frozen during the update- how long should I expect the update to take? The 'installing software update' bar is still showing itself working but has been stuck in the same position for over an hour. Any thoughts?

Update2: There is something very wrong with wireless on mountain lion recovery. I don't know what the problem is, but this link may explain:
http://osxdaily.com/2012/08/10/os-x-mountain-lion-10-8-1-beta-released-for-dev-t esting-may-include-wi-fi-fix/
Wireless recovery would start out with over 25 hours estimated and kept on failing. It turns out to be a two step process of downloading a few Mbytes then a 4Gbyte .dmg file, but I couldn't even download the Mbyte file. I bought the thunderbolt to gigabit ethernet adapter, plugged it in, restarted recovery and download of a little more than 4Gbytes took less than an hour. My limiting factor was probably comcast home internet rate of 12Mbps. The wi-fi wireless connection should be able to do over 100Mbps, so wireless shouldn't be much slower than wired, except wi-fi wireless is broken. Now that ML is installed and updated, wi-fi seems fine now, as I am using it right now, but I haven't tried downloading a big file yet.
Don't use wi-fi wireless for Mountain Lion recovery.

I downloaded the os 6 by wifi and when the phone restarted it told me to plug into itunes. I did that and the iphone software update has been stuck on '70 hours remaining' for the last 3 hours. Help!

I downloaded the os 6 by wifi and when the phone restarted it told me to plug into itunes. I did that and the iphone software update has been stuck on '70 hours remaining' for the last 3 hours. Help!

it says " itunes has detected an iphone in recovery mode. you must restore this iphone before it can be used with itunes" so i restore it and after it gets finished it says " the iphone :iphone" could not be restored. the device cannot be found" but ive used this itunes since i got this phone.

HT4623 What if your software updates has been deleted

What if my software updates has been deleted

The Settings > General > Software Update option only appears when you have iOS 5+ installed, if you have iOS 4 on your iPad then you can only update via your computer's iTunes, as described half-way down the page that you posted from.
To update via a computer, connect the iPad to your computer's iTunes and copy any purchases off the iPad to your computer via File > Devices > Transfer Purchases. You may also want to copy photos and any important documents off the iPad as well e.g. via the file sharing section at the bottom of the device's apps tab when connected to iTunes, via wifi, email, dropbox etc - they should be included in the backup, but it's best to have a copy of them outside of the backup just in case. You can then force a backup of the iPad by right-clicking the iPad 'Device' on the left-hand sidebar of iTunes and selecting 'Backup' (on iTunes 11 you can enable the left-hand sidebar via option-command-S on a Mac, control-S on a PC)
Then start the update by selecting the iPad on the left-hand sidebar, and on the Summary tab on the right-hand side clicking the Check For Updates button
Updating to iOS 5+ : http://support.apple.com/kb/HT4972
Your iPad will be updated to the highest iOS version that it supports, which for a first gen iPad is 5.1.1, and for other iPad is iOS 6.1.3

HT1923 i updated my ipod touch software and it made my ipod touch be restored. now my itunes does not sync my stuff and everything is backed up.

i updated my ipod touch software and it made my ipod touch be restored

Restore loop (being prompted to restore again after a restore successfully completes): This issue is typically caused by out-of-date or incorrectly configured third-party security software. Please followTroubleshooting security software issues if USB troubleshooting does not resolve this issue.
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
Error 50: This error (and error -50) are timeout errors. Follow the steps for errors 13 or 14 above.
Above from:
http://support.apple.com/kb/TS3694

Installing Software Update has been running for over an hour now, anyone else having the same issue?

Installing Software Update has been running for over an hour, anyone else have the same issue?

Hopefully it's been resolved by now - I have no idea how large each one of those files are. The progress bar tells you; FWIW, I only download one at a time - makes it easier and faster and you can choose to do the next one when you have time.

Apple Software Update has stopped working

"A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available."
Windows 7, iTunes 10.1.1.4 - trying to update to 10.2.1.
This has been going on for a couple of months now. The FAQ suggests deleting the Temp directory, but I can't do that because there's a file in there which I can't delete - FXSAPIDebugLogFile.txt.
Any suggestions? Thanks.

Can you update successfully using an installer from the website instead?
http://www.apple.com/itunes/download/

FROM WINDOWS (VISTA) A PROBLEM HAS CAUSED THE PROGRAM TO STOP WORKING CORRECTLY. WINDOWS WILL CLOSE THIS PROGRAM AND NOTIFY YOU IF THERE IS A SOLUTION. FIRE FOX UPDATED TO THE LATEEST, I WOULD RATHER NOT HAVE AUTO UPDATES.

FROM WINDOWS (VISTA) A PROBLEM HAS CAUSED THE PROGRAM TO STOP WORKING CORRECTLY. WINDOWS WILL CLOSE THIS PROGRAM AND NOTIFY YOU IF THERE IS A SOLUTION. UPDATED TO THE LATEEST, I WOULD RATHER NOT HAVE AUTO UPDATES. [email protected] edit

You may select how and whether Firefox updates, although like most software it may be sensible to keep it up-to-date, it is more likely to remain secure and compatible with other software whilst up to date.
* for information on the options available see [[Updating firefox]] <--- clickable link ---

TS1717 Started a software update this morning which didn't work. Now Itunes will not open at all. I get the following message."The program can't state becasue MSVCR80.dll is missing from your computer."

Started a Itunes software update this morning which didn't work. Now Itunes will not open at all. I get the following message."The program can't state becasue MSVCR80.dll is missing from your computer."

There are a couple of options that I know of to fix the issue.
One is listed in this thread - https://discussions.apple.com/message/24606478#24606478 - and involves uninstalling iTunes and related components and then re-installing iTunes. You will need to read the instructions in the thread to see the correct uninstall order.
Second option is use System Restore to set your system back to a date prior to the iTunes update. I did this before finding the thread mentioned above.
Not sure exactly what the problem is but I know, after a search, that MSVCR80.dll was indeed already installed on my computer.
Message was edited by: karivers

3.1.3 software update has made my iPod stop working correctly

Similar Messages

Maybe you are looking for