-3 error when converting music

I keep getting a -3 error when converting m4a into another AAC/mp3
Does anyone know what this is? Or why it is happening?
It's using itunes10.6
Thanks

HI Scott,
Perhaps something here might help: iTunes: How to convert a song to a different file format
Carolyn

Similar Messages

WRT1200 Network error when paying music from external disk attached to the Router

Hi everyone, I have one problem with my new WRT1200AC wireless routerFrecuently network errors when playing music from external USB3 disk attached to WRT1200AC Any idea to solve this problem Thanks in advance Regards, Rod

Wireless Configurations
Ensure the default (linksys) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios for dual band routers. Can be anything and not something that's already in use by any neighbouring WiFi routers.
What wireless modes are you using?
Try Mixed mode, single mode G or N or mixed G and N on 2.4Ghz and single mode N or Mixed on 5Ghz?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz. http://en.wikipedia.org/wiki/List_of_WLAN_channels
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.xml&pid=80&respid=0&snid=4&dispid=0&cpage=search
What security mode are you using? Preferred security is WPA-Personal. WPA2 Only.
Ensure any devices with WiFi adapter drivers are updated.
Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
Any other WiFi routers in the area? Link> Use http://www.techspot.com/downloads/5936-inssider.html to find out. Use v3. How many?
WMM Support must be enabled for single wireless N mode to function.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&articleid=5471
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9a3b1b2039741948a2365b053a93ea8_3759.xml&pid=80&respid=0&snid=2&dispid=0&cpage=search
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-essentials
http://kb.linksys.com/Linksys/GetArticle.aspx?docid=acca9b9008f04a66af818c2ab366001e_Positioning_the_external_antennas_on_the_Linksys_WRT1900AC.xml&pid=80&converted=0Rod2 wrote:
Thanks I play music fom external disk attached to the router from my internal netwok. No Internet traffic. The network error occurs between a notebook and the router in my home network Thanks Rod

Error when converting a numeric field to XML

Hi,
When i run the Adobe intractive form,i am getting following exception
"Error when converting a numeric field to XML"
Anyone plz suggest
Regards,
vinoth

Hi Vinoth Raja,
For resolving the following exception
"Error when converting a numeric field to XML"
You have to follow the below link:-
http://www.saptechies.com/error-when-converting-numeric-field-xml/
May be it will help you
Regards,
Sushma Yadav

Error when converting a constant amount MAXBT in T511P

Dear Expert,
I am encounter error as below when run payroll for Macao,
Error when converting a constant amount MAXBT in T511P
CONVERT_TO_LOCAL_CURRENCY has been Called
Data used:
Validity end date: 28.02.2014
Constant: MAXBT
T511P Currency MOP
Currency of payroll driver HKD
Therefor, do the checking on OE00 and check the currency and validity dates for MOP currency.
Also, checked table V_T001 table the currency that assigned for the company code.
Checked the MOP currency and ISO code in V_TCURC table. And checked ISO code in V_CURC table as well.
Still encounter error as above, appreciate you advice.
Thanks,
Mel

What are the values for :
Country grouping for PA/PSA:
Currency appearing in IT0008:
Country key in IT0006:
Bank Country in IT0009:

Error when converting time stamp in date time time zone CST in IC

Hi Experts,
We have recently upgraded from CRM 5.0 to CRM 2007. We are using IC WEB Employee interaction center.
so when agent create service ticket in interaction center and close the ticket on same day we are getting an error saying Error when converting time stamp in date time time zone CST.
we thought there may be problem while installing SAP CRM by basis team in time zone, but we did not find any problem.
So please advice how to resolve this issue.
Regards,
Teja

Hi Teja,
I saw a similar message, and it was resolved by adding a timezone to the user profile defaults tab in SU3. I believe the system has been configured to convert between users' timezone and the system timezone, therefore it needs to know each users' timezone.
Regards,
Simon.

GR224 Report Painter: Internal error when converting a report

Hi
Using FAGL_RMIGR transaction I've trasferred report 8A3-0010 in a
custom library ZXX. The migration happened without error messages. I've
tryed then to run report FL3-0010 by GRR3 transaction but error message
GR224 appears
Report Painter: Internal error when converting a report
Message no. GR224
Diagnosis
During the internal compilation of a Report Painter report to a
Report Writer report, sets are generated. This caused an error in the
subprogramm GENERATE_ROW_MULTI. The return code was 7.
System Response
The report could not be generated and/or saved.
Procedure
Please call the SAP Hotline and send them this longtext as well as
detailed information describing the circumstances in which this
error
occured.
Please could you help me?
Thanks in advance
Giovanna Scamardella

HI,
SAPNET notes search with GR 224 brings some old (but maybe helpful) notes: 37611, 193392,137231, pls. check.
Best regards, Christian

Why am I getting a -50 error when moving music to my iTouch?

Why am I getting a -50 error when moving music to my iTouch?

As Jim as stated, you do not want the OS, video app, and media all competing for hard drive access.
It may have worked before, but that doesn't mean will work henceforth, as you have learned.
A FW800 portable drive will cost about $75.00.

Error:-"Internal error when converting a recurrence documentu201D

Hello ISU Experts,
For customer I am trying to create a new BBP with transaction EA61. This is done without any errors until I try to save the new BBP. Then I receive the following error:
u201CInternal error when converting a recurrence documentu201D
Kindly help me in resolving this issue so that customer can receive their BBP.
Thanks in advance
Shabnum

Hello,
Have you tried to do a note search for error >4011 "Internal error in converting a repetition document"
Here are some I found......please see which is relevant for your system and implement them...
367152
131335
410434
571098
561664
569037
566972
402934
565100
155572
153495
553711
203706
183259
170406
182403
619942
700304
855780
214947
I hope this helps...
Regards
Olivia

Timeout error when converting PDF to Word

Is anyone available? I have a time sensitivity project - that would be simple for most folks...Need a question answered

Hi Sara,
my PDF cannot be read by Adobe after all. I have tried with one page but
it still cannot read it. I would like to return the programm because it
doesn't help to solve my task. Please be so kind and advice how I can
return it because I will not use it.
Kind regards,
Marie Schechter
Am 09.06.2014 19:35, schrieb Sara.Forsberg:
>
Timeout error when converting PDF to Word
created by Sara.Forsberg
<https://forums.adobe.com/people/Sara.Forsberg> in /Adobe ExportPDF/ -
View the full discussion
<https://forums.adobe.com/message/6444999#6444999>

Error when converting a 1602i to Autonomous

Hi all... just looking for a little help. I'm trying to convert a 1602i to an Autonomous OS.
I downloaded: ap1g2-k9w7-tar.152-2.JB.tar
Performed the following:
1.) Set PC LAN address to 10.0.0.5
2.) Start TFTP Server and point to folder holding the Autonomous IOS.
3.) Set timeout to 30 seconds
4.) Made a copy of the IOS and renamed it to: "ap3g2-k9w7-tar.default"
5.) Connect AP Ethernet port to Laptop LAN port using a Cat5 cable.
6.) Reset AP power holding the MODE button until the LED blinks Red (~20seconds) and then release the button.
The AP reloaded, and started downloading the IOS from the tftp....
Then I get the following message: (a lot of additional extraction messages I didn't paste)
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_sysconfig.shtml.gz (7145 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_stationview-client.shtml.gz (5554 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_ap.shtml.gz (4774 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm.shtml.gz (5294 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm-groups.shtml.gz (7511 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm_summary.shtml.gz (5061 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB (9206971bytes)..........................................................................................................................................................................
Premature end of tar file
ERROR: Problem extracting files from archive.ap:
I've performed this on 2602 without any issues... and we have tried doing the tftp in romon...
ap: tar -xtract tftp://10.0.0.5/ap1g2-k9w7-tar.152-2.JB.tar flash:
Same result... went back to Cisco.com and downloaded the file again and tried again, same result.
Any help would be greatly appreciated.
Rich

I've tried both processes multiple times and have finally gotten to what appears to be the end. However after I reset the AP, I get an error when the AP starts loading the IOS from flash.
xtracting ap1g2-k9w7-mx.152-2.JB/S5.bin (106106 bytes).......................
extracting ap1g2-k9w7-mx.152-2.JB/K2.bin (5830 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/K5.bin (75790 bytes)................
extracting ap1g2-k9w7-mx.152-2.JB/info (277 bytes)
extracting info.ver (277 bytes)ap:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 183 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 10417152
flashfs[0]: Bytes available: 21580800
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 6c:41:6a:98:05:73
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Wed 30-May-12 03:34 by binugopa
ap:

Error when converting form to XML

I get this error when trying to convert a form using this method:
frmf2xml.bat OVERWRITE=YES AvaAcPt.fmb
Oracle Forms 10.1.2 Forms to XML Tool
Copyright(c) 2001, 2005, Oracle. All rights reserved.
Processing module AvaAcPt.fmb
WARNING: Invalid value (100) for property DataType on object OK.
WARNING: Item CURR_CODE - all ListItemElements must have an Index, Name and Value.
WARNING: Invalid value (100) for property DataType on object OK.
WARNING: Invalid value (100) for property DataType on object INACTIVECUSTOMER.
WARNING: Invalid value (100) for property DataType on object OK.
XML Module saved as AvaAcPt_fmb.xml
The WARNING: Item CURR_CODE - all ListItemElements must have an Index, Name and Value. is obvious. It a list is empty this warning is thrown out. Of course my concern is when we do the XML to Forms conversion later will the list item and associated code be reconstructed correctly?
As for the 3 OK buttons and the INACTIVECUSTOMER button the converter puts a DataType attribute, which is meaningless to a button.
I tried to find any peculiarities with the buttons but could not find any.
Has anybody else experienced this problem?

Hi,
I have got the same warning “ all ListItemElements must have an Index, Name and Value” when converting form from fmb to xml using frmf2xml.
Have you find any course of this and how to fix it?
Thanks!

Unknown error when converting to mp3

I am trying to convert a track I just downloaded from the itunes store to an mp3. I have done this many times and I know how to do it. Except now when I select to convert to mp3, I get "Itunes Unknown Error (-3)". When I try to convert to one of the other options, it just gives me the first 15 seconds. But what I really need is the mp3.
Stefan

I too have been getting this error when attempting to convert a newly purchased song to mp3. This has only started happnning recently in iTunes 10.6.3.25. It turns out that this happens when the newly purchased songs are not complete. The real problem seems to be with downloading new songs form iTunes Store. iTunes reports a successful and complete download, but when I go to play the song, only 30 seconds to a minute of audio exist. It has been occurring so frequently, that I will not purchase another song until the problem is fixed.

Error when searching music in iTunes

On my iPad (purchased in Los Angeles where I use it) when I have iTunes open and I want to search for music to download, I use the upper-right search window. When I type in an artist's name, say Ray Charles for instance, iTunes shows a long list of options for his music. When I choose any of the displayed items, I get an error message that says "Your request could not be completed. The item you've requested in not currently available in the U.S. Store." I can download any song listed on the front iTunes cover page, but I get that error when searching for any artist. I was on the phone with Apple for over an hour today about this, and I stumped them. Any ideas? Thanks.

Hi Daniel ...
Since Apple couldn't figure this out.. I'll give it a shot.
Tap Settings / General. Turn on Location Services
Then in General tap Date & Time. Make sure you have the correct time zone selected.
If nothing above has helped, you didn't mention what troubleshooting Apple suggested so I'm hoping if they didn't suggest you restore the iPad's software, that may help.
Follow the instructions here on page 139 of the iPad Online User Guide: http://manuals.info.apple.com/enUS/iPad_UserGuide.pdf
Carolyn

QT Pro Crashes with "Export Controller" error when converting M2V to H.264

I am currently experiencing a problem with QT Pro for Win. Any time I try to convert a M2V file to an H.264 encoded .mp4 file, QT pro gets approx 10-16% complete with the conversion and then crashes. (This happens when trying to encode an 2hr SD M2V file taken from a DVD or a 1/2hr M2V HD file recorded via EyeTV, so the resolution/size isn’t an issue.) The error message is always that there was a “QT Export Controller error”. I do not get this kind of error when using the same files with QT Pro on my MacBook only on my windows box. I am running the most current version of QT. Does anyone have any ideas on this?

Hi,
I too am having crashing issues.... and I too got no help from Apple. Just go to website they said... great!!?? Now I know why I never use these guys products!!!
However, rant over, I do have a need to use Quicktime.
I am trying to use Quicktime to convert quicktime movies to the new H.264 codec, a function available with Quicktime Pro.
However when I go to export window and then to the video setings window, quicktime just suddenly closes(not crash). I can go into the audio section though and change options in there. I have uninstalled and re-installed with no luck.
This is extremely frustrating
any help greatly appreciated
sharky

Anyone else getting errors when importing Music Library music into non-native apps?

I have had a bunch of Music Production apps On my iPad for a long time and all the way through iOS four iOS 5 they worked just fine importing songs from my iPod library on my iPad and my iPhone however all of a sudden after the iOS six update they do not any longer seem to have the ability to import these songs. It appears to be a universal problem across ALL non-native apps ... On songs that are DRM-Free. I have specifically tried importing tracks that have imported before with no problems, downloading new copies of the same tracks, and purchasing new DRM-free content in the iTunes Store. None of which will work. My devices are not jailbroken, or altered from factory in any way, I just purchased a new iPhone 5 and a new iPad 3 and neither of them are allowing me to import these tracks. I have tried:
AnyTune / AnyTune HD
Vocalive (paid version) from IK Multimedia
Amplitube / Fender Amplitube from IK Multimedia
ISequence Pro HD
Studio HD
Is anyone else experiencing this problem? I have -- on a few apps -- been shown the "Convert this song to a different format and try again" dialog, and I can import songs if I use my laptop and a browser, but I can't seem to import any song directly from the Music Library stored locally on my iPad or my iPhone.
Help?
Best Regards, Rob Norton

Thanks, Ed.
Well, if iTunes is running, I figured out that you can drag the folder where the wav files are directly onto the main portion of the iTunes screen. This will
import the wav files into iTunes. Then group select the new song
entries and use "convert selection to AAC" from the Advanced menu.
There may be a way to convert without creating double entries for the
songs (I think that's the way you have to do it in iTunes: hence my attitude that iTunes is convenient in some respects, but less than clear in other respects..in other words, it's not a perfect program), but I delete the wav tracks after the conversion.
This is what I've gleaned from using iTunes a bit and from having been advised by friends. So, other than using a third-party freeware like X Lossless Decoder to convert music files before moving them onto iPod, apparently this is what you have to deal with when using the iTunes program.
If any Apple people are reading this, I would personally like the iTunes "importing" and display functions to be clearer and less cumbersome to use (like that third-party freeware). iTunes seems to be easy enough to use if you're importing music from a CD, but measurably less so if you just want to convert music files residing elsewhere on the computer's hard drive.

-3 error when converting music

Similar Messages

Maybe you are looking for