3 Screens with MacBook Pro 13' ? or just with the 15'
is it possible to connect 3 screens (no Thunderbold) with the MacBook Pro 13' Retina (early 2013) or only with the 15' Retina with the external graphics card.
Hi,
It really depends on what you'll be using the MacBook Pro for.
If you're selling your iMac, will your MacBook Pro be a desktop replacement? If so, I would go down the 15" i5/i7 route, but that's based on HD encoding requirements I currently do on my iMac.
As it is, I recently sold a 2008 unibody 15" 2.53GHz as I found it too large to comfortably carry around. I was thinking iPad, but decided a 13" MacBook Pro was the best of both worlds, a fairly capable mobile offering, physically smaller than my old 15" unibody yet more powerful than an iPad.
The 13" reminds me of my original PowerBook G4 12", which was my prefect travel companion (computer wise).
Similar Messages
-
i have a macbook pro my gf just got the air and she can send imessages from her laptop why cant i?!?! i have mac OS X version 10.7.5
Simple. You need OSX 10.8 or better
-
Best screen resolution Macbook Pro 17"
Question: What is the best screen resolution Macbook Pro 17"
It's also the only one currently available.
-
How do I fix a initializing problem with my macbook pro? I only get to the blank screen with the apple logo and the "processing something" sign... it just doesn't start the system....
Please help
MarceloIf there is no loading bar, it's usually a problem with a third party kext file in OS X itself.
You can press the power button down to force a hardware shutdown, then reboot holding the shift key down on a wired or built in keyboard, this will disable them and you go around and update your third party software.
Gray, Blue or White screen at boot, w/spinner/progress bar
Also take this time to backup your users files off the machine if possible.
Most commonly used backup methods
Sometime that won't work and you need to do more
..Step by Step to fix your Mac -
When I connect my Macbook Pro to my Dell DLP projector, either via cable or wirelessly, I just see a dark screen with the mouse and mouse trails only, can any one help?
jpmarkques post is a good start point, after folling his directions, you can try detect displays. Also try different rsolution and refresh rates.
Most of the projectors I have used support a 1024X768 res.
Youcan also try a pram reset if it still does not detect.
Leave theproctor connected and powered up, power down the MBP.
Power back up the MBP and hold the following keys before you hear the start up chime:
Option, command, P,R (no commas) continue to hold these keys till you hear the start up chime 2 times. -
Replace the Glossy Screen with the Matte Screen on a 2008 Macbook Pro?
Can you replace the Glossy Screen with the Matte Screen on a 2008 Macbook Pro?
Where would I get a Matte Screen for a reasonable price if I could change it?There are a number of issues you should consider before embarking on this project.
1. If you have a late-2008 unibody MBP, you are undoubtedly aware that there was never any anti-glare option offered for that machine. So there is no anti-glare display that was made to work with it.
2. If you choose to replace only the LCD panel and not the entire display assembly — which is probably feasible but involves a great deal of painstaking work — you will also need to buy (separately) the aluminum bezel that takes the place of the glossy cover glass panel in models that came equipped with the nonglare screen. The bezel covers and protects the edges of the LCD and the delicate electronic connections there, and hides all that from view.
3. If you go that route, you will have to make sure that the cabling related to the display you are installing is identical to the cabling related to your original display. This means checking to make sure the cable lengths, connectors and routing both within the display assembly and hinge cover and within the lower case of the computer are all the same.
4. If you choose to replace the entire display assembly with one that contains a nonglare LCD, you will have the entire, intact glossy display assembly available to sell afterward. If you replace only the LCD panel, the LCD and glass cover panel that you remove will have much less resale value and are likely to be much harder to sell at all, because you won't practically be able to offer any warranty with them and because there are probably far fewer people willing to tackle the fussy, risky display disassembly process than are willing to replace the whole assembly as a unit.
5. Even if you choose to replace the entire assembly, you will need to verify that the cables dangling from the replacement display assembly are the right lengths and have the right connectors to tie into your lower case properly. Because the assembly will have come from a later MBP model than yours, cable routing and connectors may have changed from one to the other.
If this all sounds more daunting than you were expecting, you may want to consider just applying a nonglare film to the glass covering your present screen. If you aren't happy with the results, you can fall back on the replacement option. -
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?
Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Don't install the Thunderbolt update -- it's defective. -
There is something wrong with the volumes buttons in my macbook pro, every time i pressed the one who raises the volume, it leads me to the screen where (i do not no what its called) the background is black with the date and time and a calculator. However, when i lower it, my safari tab goes out of the screen. What do you guys think i should do? I'm getting very nervous.
hey HAbrakian!
You may want to try using the information in this article to adjust the behavior of your function keys to see if that resolves the behavior:
Mac OS X: How to change the behavior of function keys
http://support.apple.com/kb/ht3399
Take care, and thanks for visiting the Apple Support Communities.
-Braden -
Im having trouble getting my macbook pro to boot up after a fail safe boot, im getting as far as the grey screen with the apple loggo. so im trying to run a disk repair but is saying the disk is locked, how do i unlock disk??
Some clarification may help.
You say you cannot boot normally. It shows a gray screen with the Apple logo.
Did you say it will boot successfully in Safe Mode (boot, then hold down the Shift key)?
How did you boot the machine to run Disk Utility? (Which keyboard combinations)? -
my macbook pro will not boot. It gets the grey screen with the apple until the bar is half way across and then shuts down. The only screen I can get to is in safe mode and I don't know what to do with that
Mac OS X: Gray screen appears during startup - Apple Support
-
Can't get my MacBook Pro to start up. Have shut it down several times and tried restarting but all I get is a grey screen with the spinning icon. Apple Support online suggested starting with power button followed immediately with the shift key. Same results. Also tried power button with shift key, command, and V. Black screen appeared instead with lots of data language but still no starting. This final page was suppose to result in an internal system check and restart but nothing happened and the black screen remains.Where do I go from here? Scheduled for the Genius Bar tomorrow but would like to resolve this beforehand.
You may be having a hardware problem that you cannot resolve on your own. Nevertheless...
...hold down the command and R keys whilst booting to try to get to your Recovery partition. If you can, use Disk Utility to try to Verify your boot drive (usually named "Macintosh HD" unless you've renamed it). If the verification fails, try to repair your hard drive. If everything appears to be OK, restart.
If you can't get into your Recovery partition, your problem is likely hardware related. If so, keep your appointment and see what the Apple techs have to say.
Clinton -
My Macbook pro 13 inch is stuck on a gray screen with the apple logo, how do I fix this?
Sooo, I was using my laptop for a while and the charger was kind of broken, it was dip in and out, and slowly I got a "Service Battery" notification. I updated my system and now everytime I try to boot up my computer it'd show a gray screen with the apple logo and a loading bar with a circular loading icon but it never actually boots up. It stays stuck at that loading screen. I don't think it's because I uploaded my system that it happened, but I'm wondering if it's because I didn't change my charger/battery, and I'm wondering if I have to get the harddrive changed or is there a way for me to recover my files and whatnot without having to whip it. Please help, and thanks in advice to any help offered.
Dwaniej,
you can try this: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Does it get past the grey screen now? -
My 06' Macbook Pro crashed with vertical, green pixelated lines and now will not advance past the turn-on screen with the apple filled with green lines as well. Then, it says to hold down the power button to restart. I have tried several times to get it past this point but tnothing helped.
I have an appointment at the Apple store today, but was wondering : will all of the information and files on my desktop be lost? Or is this a logic board problem?
Any help is much MUCH appricated.I'm not sure, if you're out of warrenty it'll cost quite a bit for the replacement of the logic board replacement...unless you have apple care. you could ask apple to try and recover your hard drive but i'm not sure.
-
I can't unlock the screen to access my macbook pro. When I enter the password it just jiggles. I'm not getting an error message, so I'm pretty certain that the password is correct. Any suggestions?
I already checked that one.
I'm baffled, especially since it will usually give you the Invalid user name or password entered message. I'm not getting that. Instead the password field just jiggles back and forth. Very odd. -
My macbook pro will not get past the gray screen with the apple logo and a loading bar.
My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.
You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213
Maybe you are looking for
-
How to read tags from pdf to print in different printers (PCL or PS)
Hello from Spain.. I would apreciate some help who to read tags from pdf to discriminate PDF Production tag for send print PDF to printer job using driver PCL or PS. I get trubles when print PDFs files made by PDFcreator (Ghostscript, intermediate PD
-
Accessing Essbase database from BI Admin tool
Hi, I want to create a new RPD using Essbase database. I want to know how to configure Essbase data source so that I can use it for my rpd file. I have BI server installed on server machine and BI admin tool on my laptop I am using version 11.1.1.5.0
-
Prerequisites for upgrading 2005B to 2007B
Hi Can anyone send me a pdf file which suggests prerequisites for upgrading 2005B to 2007B in the 2005 B database so that system can work properly? Thanks
-
Orchestral Template NOT showing up in Logic - on start! Ideas? Help?
I have the Orchestral Jam pack installed (MBP) but not all of them. Am I missing something? The jam pack is installed but does not show up in my LOGIC TEMPLATE. Help, GREATLY x 100, appreciated. Thanks It does show up in loop browser but no templates
-
Could not start the Bonjour Service service on local computer. Error 6: The handle is invalid
I have been trying to load teh new Itunes 10.5 for the last week and have been unsuccessful. When the load get to the Bonjour service it fails and puts up a message. I have Administrators rights on the machine. I have updated the OS to the latest pat