3 Speakers bandwidth problem

HI I use winxp sp2, I try many type of configuration, to get more bandwidth, the last its all airports in a 3com office connect 54mbps, I disable all protocol not needed to itunes to send music to the airports, such as QoS packet, are enable only tcp and client.
Anyone Know why and have any idea? The bandwidth used from 3 airports its only 40% at 11mbps, I suppose its windows that control hard the packet that goes in & out from the wireless card...
I hope someone know a solution to solve this problem I see some people have same problem, If also can tell me a mac user have same, to know if its really and only a windows problem and not airports or itunes that arent able the use the full bandwidth.
Thx in advance to all.
Windows XP

Yep thats right, thanks for taking the time tio reply
Skip

Similar Messages

Bandwidth Problems

We are trying to use iChat with a grandson in Iraq. We get a satisfactory Picture ( pixelates frequentl but passable) but almost unintelligible Audio. We however had an audio chat with sound as clear as a local phone call. He uses AIM in Iraq on a PC we are using Mac and iChat over here. He has bandwidth problems over there as he notices slow photo uploads and downloads. He is new at this as he just got the CAM for Christmas,does anyone know if there are there bandwidth adjustments in AIM that he can tinker with to try to improve the situation like we have in iChat, or any suggestions to try. (I doubt that adjsuting the speed on the Mac on this side will help!)

Hi,
On the Mac end it should have System Preferences < Quicktime > Streaming set to 1.5Mbps
In the iChat > Preferences > Video section > Bandwidth Limit it may pay to try 500kbps or 200kbps to limit what you send him.
AIM 5.9 on a PC does have a Outgoing adjustment and I am not sure if changing it will help the incoming stuff but it may free up processor time.
He should start a Chat with you (or you with him)
In AIM 5.9 he has his Preview in a tab behind your incoming Video.
He should bring this to the front (And take off Pic-in Pic if set)
Next to the Pic and on the right he should now have a small squarish iCon
Click on this
This will bring up a slider.
Sliding it to the left actually reduces the quality of the Pic from his end.
It is not normally visible but what it does do is allow his processor to produce more frames a sec.
If you open the Connection Doctor (Video Menu) in iChat you will see his incoming Frame Rate and Bit rate and as he slides this to the left you may see changes.
If there are no changes then the issue is going to be the Bandwidth at his end.
At this stage I would suggest a Web Browser based alternative like MeBeam
See here items 9 through 12
These use Flash in a Web Browser to allow access to the Camera and Mic
Once you have entered a room name (your choice) it creates a web page with that name and pops up the Flash Control Panel. Set this to Allow and choose your camera and adjust the Mic volume (Use Headphones/headset if possible)
The MeBeam site pops the control Panel up as soon as you enter the room and can be re-accessed via Settings. the other sites require you use the Settings Button first.
Hope this helps
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
1:48 PM Sunday; February 1, 2009

College Bandwidth problems

So I am trying to get my video chat to work with a friend from home however i keep getting bandwidth problems. It has worked before fine at other places. Is it because they are blocking the ports or limiting the bandwidth? Is there any way around this?

They are most likely blocking a port that you need. Most colleges do this to keep the possibility of attacks, etc. You might could talk to the IT dep. and get them to enable a blocked port.
This is a list of the ports that AIM needs: http://docs.info.apple.com/article.html?artnum=93208.
Also... you should, if you have the OS firewall enabled, open these ports in the OS firewall: 5060, 5190, 5297, 5298, 5678, 16384 through 16403.
Instructions for opening these ports are in the above support article.
Hope this helps,
Cory

DDTS-100 Decoder with Inspire 5500D 5.1 Speakers (DIN Problem!)

Dear all,
I bought a DDTS-100 Decoder today, thinking it will improve connectivity and sound quality of my Inspire 5500D 5.1 Speaker System, but I have run into a bit of a problem. My system has a sub which every speaker is connected to and I have to have the DIN cable connected for controlling the speakers and sub but the DDTS-100 doesn't have a din slot so my speakers will not power on when connected to the ddts-100. Is there a way around this or will I have to take back my decoder. I hope there is a solution as I would be very thankful.
Yours Thankfully,
Kyle Hunt.

kyle_hunt85,
Hitting the tab key perhaps? Gets me every time.
Daniel

IChat bandwidth problem after upgrading to Quicktime Pro 7.1

I just updated Quicktime Pro 7.1 (from 7.0) and applied the Security update to my iMac G5 1.8 GHz.
My girlfriend and I have been chatting with no problems. She's running an new iMac Dual Core and I have an iMac G5 running 10.3.9. We tried to hook up tonight and kept getting this error:
2006-05-11 21:41:51 -0400: There is insufficient bandwidth to maintain the conference.
Detected 48 kbps upstream and 162 kbps downstream bandwidth; 50 kbps required.
We're both on Cinti Bell's Fuse/Zoomtown ADSL so we have plenty of bandwidth. Set iChat bandwidth to None and st Quicktime to 1.5 Mbps T1/internet/LAN.
Any ideas why, after a month of no problems chatting, this bandwidth issue has come up? She's running 4.5 (hasn't upgraded and hasn't sone the just rreleased security update)?

OK - My gal is here for the weekend so it will be next monday evening before we can toubleshoot as I don't know any other place where I can find someone to video chat with for testing purposes. We're using AIM accounts, but like I say, before the upgrade I did it was working fine. I've been through most of the 'usual' from rebuilding permissions, diskwarrior to ensure the disk is OK. Next week I'll trash preferences and such when we troubleshoot.
I appreciate the response. If I find anything out I'll update this thread.

NoteBook speakers rare Problem

hi all,
my problem is that i cant listen music for the speakers of the laptop, sound only work with the jack plugged but strangely when i use for example skype who take the jack interface , the music start to sound in the speaker, i try all diferent combination in sound interfaces control panel
mybe a problem with drivers... i can only listen in the internal speaker if other program is using the jack interface , in other way no music can be hear
I was searched in the forum for related topic but nothing
thanks.!!!!

I just read a test about a MSI GX600, they says that it has about a 144 minutes autonomy, I don't think that the wifi module is using so much power so, you're probably right, there is a problem somewhere.
On my MSI GX 700, I have a greater autonomy on Vista than on XP, but if you just bought the computer, I suppose you use Vista.
Does you fan is working at maximum speed all the time or something like this ? (it's very noisy when it's at max speed)
You can check with Riva Turner and CPU-Z if the GPU and CPU are well clocked down when on internet or stuff like this (not in games).

"Insufficient Bandwidth Problem" and "Did not respond" error messages

I am getting 3 error messages when I try to video chat using isight and ichat with my son's PC (which does video chat with my husband's PC) I have not been able to video chat although I can instant message with my son's PC.
1. It says insufficient bandwidth"
2. It says "starting" for a LONG time, and never finishes.
3. Or they request a chat with me and I get a "Did not respond" message.
I have tried connecting with both my .mac account and my aim name inside of iChat
So far, I have:
1. Changed Quicktime streaming to 1mbps Cable
2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
4. Firewall is off
Since video chat works between my son's computer and my husband's, I doubt that it is our cable company or my son's. My son can also video chat with friends in his area. They are using msn or aim. However I have not been able to establish a connection using ichat.
If there are no other fixes, then I will probably have to call Apple tomorrow for a return on the isight that I just purchased. Too bad, because the Los Angeles Times this morning said that iChatAV image quality is superior to even Skype's new product 2.0 for Windows. At this time Skype does not have a cross platform product. Is that the problem with iChatAV, it really only works with other Macs?
Please advise if there is anything else that I can do to correct the problem. I have used an apple computer for more than 20 years, since the first little Apple IIc that I had. This is the first thing that I haven't been able to figure out.
Thank you,
Linda

HI,
This
1. It says insufficient bandwidth"
2. It says "starting" for a LONG time, and never finishes.
3. Or they request a chat with me and I get a "Did not respond" message.
Normally implies the ports are not open some where.
The bit I have changed to Bold is not specific enough
I have tried connecting with both my .mac account and my aim name inside of iChat
So far, I have:
1. Changed Quicktime streaming to 1mbps Cable
2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
4. Firewall is off
Can you tell us exactly which ports you have opened and which protocols. APple Doc 93208 is Wrong.
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, and 16384-16403, which need to be open for TCP only.
You have not siad what ports you have opened and by what method in your modem ?
Ralph

Bandwidth problems with sprint 5

I can get consistently better bandwidth using osmf 1.6 sprint 1 than I can with 1.6 spring 5. Very strange but I made several tests and it they were conclusive accross browsers. What could the problem be?

Found the problem, sorry. Starting on sprint 2 the autoDynamicStreamSwitch is set to false as default.
Which brings me to my next point: Why is OSMF so complicated?!!!!

SB Audigy 2 NX on Windows 7, speakers + headphone problem

Hi All, I plugged my USB SB Audigy 2NX into a Windows 7 x64 laptop. I have 2.1 Stereo speakers plugged in to the SB 'FRONT' Jack. And sometimes plug a stereo headset into the 'SIDE /PHONES' jack.
This works fine on my XP system. And when I plugged in the headphones, the sound will just play on the headphones
THE PROBLEM IS, on the Win 7 laptop, when I plug the headphones into the Audigy 'SIDE /PHONES' jack, the sound still plays thru BOTH the speakers AND the headphones. Does anyone have any idea why this is happening?
USB Sound Blaster Audigy 2 NX
Installed Driver: the Creative Sound Blaster Audio Driver .0.0099 (Feb 200), no errors detected on the install.
Creative Labs I-Trigue 3330 2.1 Speakers

Ok, thanks. Is the PCMCIA Audigy 2?ZS able to decode from external sources? Or is there a way for the laptop (via software) to decode, effecti'vely only using the NX as a hub to connect to the speakers?Message Edited by Alonso4 on 03-27-200704:54 AM

Network Bandwidth Problem

Hello everyone,
I am having bandwidth issues in my network. The current internet line from the ISP is 50Mbps, but we are not getting the complete bandwidth (almost 20Mbps is lost). I have been analyzing the network past few days using PRTG and learnt that a major portion of the bandwidth is being utilized by an unkown Source IP going towards unkown destination IP using an unknown port number(none of the IP's and Port are being shown in their respective tables, just the utilized bandwidth shown but rest of Source IPs, Destination IPs & Port being used are shown), So I came to a conclusion that some one in my network might be using a proxy such as hotspot shield which is taking major portion of the bandwidth and where i assume the bandwidth is being leaked. Is there any means of blocking the use of hotspot shield?. I am not sure whether this is the actual problem, Or are there any other possible problems such as a bad network layout. help needed badly
Thanks in advance

You haven't provided enough information to make an informed recommendation.
A high level description of your network connectivity and information about what instrumentation your used to draw the conclusions you have from PRTG would be a good start.
You need to ensure that your are capturing information from the right point (or points) to account for all the the load presented to your provider.Typically this would be a Netflow export and/or SNMP query taken from an egress interface at or near your provider handoff.

Do I have a Bandwidth Problem

I have a G5 Dual 2 gig when I am using idvd to mux my DVDs I find I cannot us the import button in iMovie I want to know if this is natural. I have a terabyte 800 drive attached to my 800 firewire port and I am using a Canopus ADVC 100 which is my capture analogue to DV capture box which is a firewire 400 device which is attached to the 400 firewire input on the back of the G5. I am using all 3 of my USB ports on the back of the G5. I have a Belkin USB 5 way PCI card which has 5 lacie drives attached to it. I have a combie PCI card which houses 3 USB slots and 2 Firewire 400 slots of which I am using a Dongle USB Key in one of the 3USB slots, and a Lacie Dual layer external firewire 400 in one of the two Fire wire ports on this combie card the rest of the slots are left free. All the slots on the front of my G5 are left vacant.
The Question
Can anyone let me know whether the problem is that I have too many devices attached and that it is eating up my Bandwidth. Or is it a safety feature where the G5 shuts off any attempt to use my canopus to import Footage into iMovie.

Hi I feel we have drifted somewhat this is my original problem
_Ordinarily iMovie works ok no probs!_ Its Just when I am in Mux mode with iDVD it seems to stop me from using the Canopus in iMovie or Final cut pro both app say that they have lost connection with the capture device

Airport Express 802.11n - speed, throughput, bandwidth problems only 1MB/s

Hi there,
I got a brand new Airport Express with 802.11n. But I'm really disappointed with the speed in a draft-n-only environment.
Before I used as a router my 54Mbit/s Linksys WRT54GL with DD-WRT v23, which gave me on its g-Standard network a throughput of 3 MB/s when copying something via finder to my Ubuntu server.
But with the new AE I got only 1 MB/s as transfer rate for the same job. I tried already various configuration setups, but nothing helped. It seems to me if there is a bandwidth limitation thing in the AE.
Can someone help me to find the reason for my problem or give me some advice after what I have to look at?
Many Thanks,
Jan.

Welcome to the discussions, Tiggar!
A few suggestions from here, where my AirPort Express far outperforms my older "g" router.
1) Try to position the AirPort Express as high as possible and away from any other electronic gear. The general design of the product unfortunately encourages users to position the device low on a wall, often behind a desk and close to other electronic devices that sometimes can interfere with the wireless signal. Use an extension cable to get the Express up high and give it as much free air as you can.
2) You need to remember that higher frequency "n" signals...although faster...do not penetrate walls and other obstructions as well as lower frequency "g" signals. Try to establish a line of sight situation between your computer and the Express if possible and mimimize obstructions in the signal path.
3) Your Linksys may have been using a different wireless channel than the Express. Try different channel settings on the Express to see if you can find a good channel that is free of interference. To do this, open AirPort Utility, click Manual Setup and click the Wireless tab below the row of icons to get to the Wireless settings page.
4) Turn off any cordless phones that you may have there for an hour or so to see if you notice any improvement in performance. If you do, try to position the cordless phone as far away as possible from the AirPort Express.
Let us know if things improve when you can.

MSI HD3870X2 OC Bandwidth Problem!

Ok so i installed my new X2 OC edition and noticed that i only get 28.8GB/s bandwidth,
ive seen other people on internet with the same problem.
I have one 6pin and one 8pin connected.
This is what its suppose to be @ 512mb!
512mb = 57.7 GB/s x2 =114.2GB/s
This is what i have
28.8GB/s
And it shouldn't be be due to 2d clocks, the bandwidth should remain the same at all time.(i was told)
I added a picture for you so you can see my problem.
My system specs:
q6600
GA-P35-DS4
MSI HD3870X2 OC
Thermaltake Toughpower 750W
The PCI-E bus is set at x16 so that's not the problem here.
Any assistance is appreciated.
Thanks in advance
//|Ano|
*edit*
Do you have a Tweaker (overclocking program) that works with 3870X2?
Again, thanks!

Quote from: |Ano| on 23-February-08, 03:20:18
@Bas
I am talking about the memory itself (2x 512mb=1024mb) and not the bus bandwidth.
Well you are using the wrong terms.
First, memory-size is expressed in MB = MegaByte (mb = milli-bit never heard of that)
Second, memory size and memory speed are 2 different things and have nothing to do with each other.
Third, (memory) speeds can be expressed in either Mb(it) or MB(yte), but don't forget, it takes 8 bits to make a Byte.
Also speeds are normally in Mb/s or MB/s, but those never express size.
Please use the correct names next time, else we (me) have no clue what you meant to say.

Bandwidth problem

dear sir,
i am getting 256kbps dedicated leased line what should be the upload and download speed.

The line rate is 32 KBytes per second. If you add compression, you might improve on that, depending on the nature of your data. Practically, you are unlikely to achieve greater than 90% of the maximum line rate.
However, don't forget that there are a lot of other factors invoolved that could slow you down, such as server performance, TCP window size vs. end-to-end delay, etc. etc. The overall performance is not entirely determined by the line rate.
Generally we assume that the available bandwidth is 75% of the line rate, the remaining 25% being the allowance for overheads, routing protocols etc.
If you are having a specific problem with the line, then post a show int from both ends of the line, and we shall see if we can work out what is going on.
Kevin Dorrell
Luxembourg

Multiple speakers, multiple problems

Okay I know alot of people use 2-3 pairs of speakers for mixing. One to judge the low end the others for blah, blah, blah. Right now I am mixing on some Dyaudios and I also have a pair of NS-10s (M-Studio). I am afraid to get rid of my NS-10s just because I have had them so long, but I have hardly turned them on since I bought my Dyns. So I was thinking maybe I will develop a method of using both of them, or....
So the question is: Should I just use one set of monitors and get really comfortable with them and use other enviroments (ie: car, jam box, etc.) for judging mixes in the real world?

Steven,
Thought I'd jump in with my 2 cents, since you mentioned two sets of speakers I also use.
I'm sure there are numerous theories on this subject, but I have always relied on several sets of monitors to constantly check my mixes, and all the mix engineers I know do the same.
The NS-10's , as you know, once you're familiar with them, really do help in placing the "money" tracks properly, and the old saying is still applicable... if your mix sounds good on NS-10's, they'll sound good everywhere.
With the Dynaudio's (I use the BM6's), they sound really, really good, have great definition, as well as a solid low end, so it's easy to just use those. However, it's important to have other references, and the NS-10's are an excellent choice.
I also recently bought a pair of Mixcubes. These were designed to take the place of Auratones, which some of you may remember. The purpose of these single driver speakers, is to hear what your mix sounds like on a set of crappy speakers, like computer speakers, or the like.
I'm finding their use VERY valuable, because of their limited frequency response. Not to listen to all the time, of course, but to see how the mix would hold up on lesser speakers.
So, that's my long winded way of saying, it's my opinion to make use of several sets of speakers, when mixing. Sure, one set can be "the mains" (mine are the Dynaudios), but you really should have at least one other set, for comparison, even if that second, or third set is the car stereo, or a boombox.

3 Speakers bandwidth problem

Similar Messages

Maybe you are looking for