30" Monitor Display... Tiny View of Applications and Windows

Hello!
My 30" was is set at 2560 x 1600 and was in the wrong port... the images were blurry. I switched over to the proper port and everything is very crisp.
However, I am working on a 30" screen and all of my programs and windows are very small in comparison to the screen. Relative to the screen size, my programs, email, etc. are tiny.
Would anyone have any suggestions?

For example,
http://bp3.blogger.com/_DcF07dFodQ8/Ru7ODTGWvrI/AAAAAAAAAE4/4oL-hUlufrc/s1600-h/ 1.jpg
this is what my illustrator program and window look like when i open the program up AND... this is after applying the Apple + 0 command for a full-screen window.

Similar Messages

My macbook air (version 10.9.4) display flickers, has random tabs and windows opening, and there are random ads almost everywhere. All this happens when I am using safari. What can I do?

My macbook air (version 10.9.4) display flickers, has random tabs and windows opening, and there are random ads almost everywhere. All this happens when I am using safari. What can I do?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can read it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;/(de|[nst]):/p;' ' {sub(/^ +/,"")};/r:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,Inter,iTu,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Thunderbolt display not working with bootcamp and windows 7

I am running a late 2013 MBP Retina display with a Thuderbolt monitor. I am running windows 7 on a dual boot partition. I can not get my thunderbolt display to work while working in windows. The screen is currently black. I have attempted to follow the instructions in prior posts regarding this issue with no success. Is there a clear fix to get the monitor to work? Thank you

it has to be plugged into the machine before you power on the machine, it is not hot swapable like on OSX
does the screen work in OSX

Unable to stop applications and windows reopening after reboot Yosemite

I am wondering if my system became corrupted about a week ago after working well since upgrading to Yosemite when it was first released. When I reboot my system a number of applications open windows including Mail, iTunes, Excel, Adobe Reader, Calendar, Chrome, and VMWare. A window pops up asking for my iCloud password and it usually requires more than one attempt to enter the password before this disappears.
I have searched online and tried all the usual remedies. I have selected "Close windows when quitting an app" under "Settings, General". I have ensured that these items do not appear under "Login items" in "Settings, Users & Groups". I have tried selecting and unselecting "Reopen windows when logging back in" on the "Restart badge" that appears when requesting restart.
I also tried reinstalling Yosemite and later tried a "clean install" of Yosemite. In the latter case, I did restore my applications from Time Machine backup so it is not really a "fresh" system.
Does anyone have any idea how to approach this problem short of doing a clean install of Yosemite and then reinstalling all my applications?

I am wondering if my system became corrupted about a week ago after working well since upgrading to Yosemite when it was first released. When I reboot my system a number of applications open windows including Mail, iTunes, Excel, Adobe Reader, Calendar, Chrome, and VMWare. A window pops up asking for my iCloud password and it usually requires more than one attempt to enter the password before this disappears.
I have searched online and tried all the usual remedies. I have selected "Close windows when quitting an app" under "Settings, General". I have ensured that these items do not appear under "Login items" in "Settings, Users & Groups". I have tried selecting and unselecting "Reopen windows when logging back in" on the "Restart badge" that appears when requesting restart.
I also tried reinstalling Yosemite and later tried a "clean install" of Yosemite. In the latter case, I did restore my applications from Time Machine backup so it is not really a "fresh" system.
Does anyone have any idea how to approach this problem short of doing a clean install of Yosemite and then reinstalling all my applications?

Hidden views of applications and Menu Bar

I have recenly loaded Mac OS X on to an older dormant G4 Digital Audio. I am using a 17inch VGA display. The problem is that the G4 thinks that there is useable screen area to the left of the current screen. That is, I can move my curser over to the left off the screen and pull open windows over to the viewable area by clicking and dragging. How can i turn off this extended wide screen and limit the G4 to operating in the viewable area on the current VGA display?
Powermac g4 digital Audio Mac OS X (10.4.4)

That is normal behavior for the desktop. The extended areas of the desktop can be displayed if you have multiple monitors.

Cp 8 responsive design module in Saba LMS displays desktop view on iPad and Android phone

I'm testing a short, four slide responsive project in Saba Enterprise Cloud 7.2 (this is the latest version of Saba). It's SCORM 1.2 and I used the Publish for Devices feature to create my zip. When I preview the module in the LMS on an iPad and Android phone, the desktop view is displayed on both devices. Has anyone successfully deployed a responsive module in Saba?
Thanks in advance!

This is an issue seen in many third party LMS.Please contact your LMS vendor and ask them to fix the issue.In case they want some more information, please send me a mail at [email protected]

Adobe AIR HTML/JS application and Windows Native Installer

Hi,
I am building an Adobe AIR application with HTML and Javascript and I would like to know how to make an Windows Native Installer.
I am trying to build it with Flash Pro but it keeps returning the error 'Invalid SWF file'. At the application.xml file the <content> points to my index.html file. I don't use any SWF file. When I change this to point to the SWF it does build tha installer but the application loads the SWF.
Is there any way to build a Windows Native Installer and the initial content be an HTML file?
p.s. I tried to extract the files from the installer file and edit the application.xml there to point to the index.html. But I can't repackage the files to a valid air native installer.
Thank you.

Hi,
Thank you for reporting this. The internal bug number for the issue is #2740755. The issue is currently under review and will be investigated by one of AIR team members.
Regards,
Catalin

Horizon View 6.1 and Windows 2012 as Desktop OS

Hi Community,
we are currently running a PoC for Horizion View 6.1. Various reasons require to use Windows Server 2012 r2 as guest os, afeature which should exist in 6.1 according the release notes.
When trying to create a linked clone pool with a windows 2012 template we get the message that the guest os is not supported. I know that we only have a 2012 Standard Edition for the PoC but would have DC Edition once we decide to go forward with the solution.
How des View check the edition of the template and is there any possibility to get this working since we need to move on with the poc?
Thanks an kind regards,
- Matthias

So today got some word from their office. They were using RDP from 8AM until 12PM all was working fine. Then got back after lunch about 1PM and got a few connection lost errors when they tried using RDP again. Its weird since they didn't have disconnects
in the morning, and started having them after lunch.
Also noticed, that two pc were not using RDP and were disconnected as shown in task manager. And they still got request timeouts.
Maybe this is not a remote desktop issue?
TASK MANAGER
The 2 disconnected pc's ping screens:

External Monitor will not display full view MS apps.

I have a HDMI monitor that was previously working fine. The other day I went to use Word and Excel and the applications would only appear in the lower toolbar. When I would select them they would not enlarge. They remained in a thumbnail view. My email and Internet work as expected. Any ideas what's causing this?

Hello @Bjenkins,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your external monitor will not display full view Microsoft applications on your system, and that certain functions will not work on your desktop. How long ago did your applications work properly? I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

How to display a view which contain interactive form in an external window

Anyone know how to display a view which contain interactive form in an external window?
I managed to display the view in an internal window with the following code:
IWDWindowInfo windowInfo = (IWDWindowInfo)wdComponentAPI.getComponentInfo().findInWindows("PdfReportWin");
IWDWindow window = wdComponentAPI.getWindowManager().createWindow( windowInfo, true);
For external window, I tried this method : wdComponentAPI.getWindowManager().createExternalWindow(String URL, String title, boolean modal) but there are no parameter for view name?
Maybe this is not the correct way, really appreaciate if anyone can help.

Hi,
            U need to the following
           1.Create another window
           2.Create a view in it tat contains Interacive form element.
           3. call this window dynamically thru the first window by creating a context element of IWDWindow type
The code may help:
IWDWindowInfo windowInfo =(IWDWindowInfo) wdComponentAPI.getComponentInfo().findInWindows("SearchEmpwind");
      IWDWindow window = wdThis.wdGetAPI().getComponent().getWindowManager().createWindow(windowInfo, true);
      window.setWindowPosition(WDWindowPos.CENTER);
      window.setWindowSize(400, 250);
      window.open();
      wdContext.currentContextElement().setEmpSearchWind(window);
Regards
Ishita

How to group more than one view in a single window?

Hi,
I want to group three or more views in a single window.
I need a element, which is similar to VIEW SET in webdynpro for JAVA.
how to do it?

Hi,
In wd-abap the concept of viewset is not used instead the viewContainerUIelement is used to achieve the same.
create a main view say v_main in that add ui control viewContainerUiElement
create a another view say v1.
go the the window .. embed this view v_main to the window , u can see then below the view the control viewContainerUielement , in that u can add the view v1 inside this container . so if u create more containers inside the v_main ,then u can display more view inside this and the plugs can be created and fired as same as in java.
Hope this will help u .
Regards
Yashpal

Dual-DVI Adapter and Windows 7

Just under a month ago we have purchased a new mac mini that's running Windows 7. Mac mini is now connected to a 29" UltraWide AOC Display using a Dual-DVI link adapter. Everything is working okay in terms of resolution, but the screen cannot detect input after Windows 7 boot screen.
When you first switch on the mac, you get the Windows start up and then it goes to a black screen. The monitor displays no signal on DVI and goes to standby. We have to unplug the DVI adapter from the thunderbolt port and plug it back in, for the monitor to come back on.
Any ideas what could be wrong? Do we need a special driver for the adapter?

As previously stated mount # and chroot in the install grub to /dev/sda mbr - nothing will be lost from your hdd and grub will boot in preference to winloader
Use the the beginners guide for the commands and adapt for your system
https://wiki.archlinux.org/index.php/Be … ase_system
https://wiki.archlinux.org/index.php/Be … bootloader
... and always install windows first - if you did a clean windows install it may be best to install all the service packs / major updates before bothering to reinstate grub as you may find you need to repeat the process anyway

Compatibility forms 6i and Windows Server 2008

Hi,
We want to change our Server from 2003 to Windows Server 2008 64bits.
My question is : is there a compatibility between Oracle forms 6i (our application) and Windows Server 2008 ?
Will the migration be successfull, or will we have some bugs?
Thks for your help.
O.

YES. It worked perfectly for me, you'll have to use oracle 8/8i lite though.

I was told of an application that will allow the use of a second screen to view my data and files, but I forgot its name. I'd like to make the connection because my LCD is broken.

I was told of an application that will allow the use of a second screen to view my data and files, but I forgot its name. I'd like to make the connection because my LCD is broken.

You don't need an application, just plug a compaitble monitor into the display port of your MacBook Pro, set the screen up in System Preferences>Displays

XML page cannot be displayed cannot view XML input using XSL style sheet Please correct the error and then click the REfresh

XML page cannot be displayed cannot view XML input using XSL style sheet Please correct the error and then click the REfresh

Is the error message displayed in Firefox or in IE, or in a customized window that doesn't identify the browser?
''If it displays in Firefox:''
It's possible that the Troubleshooter doesn't work correctly unless IE is your default browser. You could test that possibility by having IE make itself the default and testing the Troubleshooter again.
''If it displays in IE or embedded in another Microsoft application:''
In a web search I found these suggestions:
(1) Reset your Internet Explorer settings, according to http://answers.microsoft.com/en-us/ie/forum/ie8-windows_7/cannot-view-xml-using-xsl-style-sheet/ccfe80c6-c0db-4594-a7e3-475f9eac0e85
(2) Try the System File Checker, according to http://ask-leo.com/why_do_i_get_the_xml_page_cannot_be_displayed_after_running_a_microsoft_troubleshooter.html
Any luck?

30" Monitor Display... Tiny View of Applications and Windows

Similar Messages

Maybe you are looking for