310N - web based utility password

Trying to use web based utility. Instructions are to use password admin and leave user name blank. Does not allow me to enter. Advice??

When you configured your router, using the setup disk at that moment have you changed the router password, if yes then you need to use that password while loggin to the router setup page using web base utility.
If you dont remember your router password, then i think you need to reset your router. Press and hold the reset switch on the back of your router for 5 seconds (Dont hold the reset switch more then 5sec, other wise it will reset your router to factory defaults), and release the reset switch, now try to login to the router setup page using the web base utility.

Similar Messages

Web-based utility bringing up blank browser page

We are using the WRT54G router for a combination wired and wireless home network. All is working fine except when trying to access the web-based utility from the wired computer, I get a blank browser page after entering my username and password. The utility itself does not display. I have accessed it previously and know I am using the correct IP address. This seems to happen quite often. Has anyone else experienced this or have any ideas? Thank you.

You said you entered the "user name and password". I think on your router, the user name should be blank.
To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
Message Edited by toomanydonuts on 09-30-2007 10:27 PM

How do I access the web-based utility

I just purchased a wireless router...WRT300N. I want to access the "web-based utility" in order to update the firmware.
How do I access the web-based utility...help!
Thanks.

Access the router’s web-based setup page.
For instructions, click here.
Linksys Easy Answer 4030, applies to WRT300N
Upgrading the Linksys Router's Firmware
Hope this helps,
Lilla
Westell 6100 modem/router; Linksys WRT54GL v1.1 router firmware 4.30.9; Linksys WPC54G v2 Notebook Card; CenturyTel DSL using PPPoE

Error when loading web-based utility

i have numerous errors when i attempt to load the web-based utility in both IE and Firefox. most of them are java errors and seem to be related to the font. i've updated the java on my machine. i've also reset the router numerous times. part of the page will load but most of the options are missing. i'm at a loss to try to get the page to load correctly. please help!
Here are the errors that show up in firebug in Firebox....
Unknown property 'mso-style-parent'. Declaration dropped.
undefined
style.css (line 50)
Unknown property 'mso-style-parent'. Declaration dropped.
undefined
style.css (line 55)
Unknown property 'mso-style-parent'. Declaration dropped.
undefined
style.css (line 62)
illegal character
‹ '6ÐC
share.js (line 1)
illegal character
‹ $6ÐC
help.js (line 1)
share is not defined
<b><a target="_blank" href="HSetup.htm"><script>Capture(share.more)</script><br>...
192.168.1.1 (line 1202)
hsetup is not defined
<script>Capture(hsetup.phase38)</script><br>
192.168.1.1 (line 1201)
hsetup is not defined
<script>Capture(hsetup.phase37)</script><br><br><br>
192.168.1.1 (line 1200)
hsetup is not defined
document.write(hsetup.phase44);
192.168.1.1 (line 1167)
share is not defined
<TD width=101 height=25> <script>Capture(share.timezone)</script>...
192.168.1.1 (line 1065)
share is not defined
face=Arial> <script>Capture(share.wins)</script>: </FONT><...
192.168.1.1 (line 1034)
share is not defined
face=Arial> <script>Capture(share.clileasetime)</script>:</FONT...
192.168.1.1 (line 968)
share is not defined
face=Arial> <script>Capture(share.startipaddr)</script>:</FONT>...
192.168.1.1 (line 946)
share is not defined
name=lan_proto><B><script>Capture(share.disable)</script></B></TD>
192.168.1.1 (line 938)
share is not defined
type=radio checked value="Enable" name=lan_proto><B><script>Capture(...
192.168.1.1 (line 936)
share is not defined
<TD width=101 height=25> <script>Capture(share.dhcpsrv)</script>:...
192.168.1.1 (line 934)
share is not defined
face=Arial> <script>Capture(share.submask)</script>:</FONT></TD...
192.168.1.1 (line 902)
share is not defined
document.write("<OPTION value=0 selected>"+share.auto+"</OPTION>");
192.168.1.1 (line 837)
share is not defined
face=Arial> <script>Capture(share.mtu)</script>:</FONT></TD>
192.168.1.1 (line 833)
share is not defined
face=Arial> <script>Capture(share.domainname)</script>: </...
192.168.1.1 (line 822)
share is not defined
face=Arial> <script>Capture(share.hostname)</script>: </FO...
192.168.1.1 (line 811)
share is not defined
face=Arial> <script>Capture(share.routename)</script>: </F...
192.168.1.1 (line 800)
share is not defined
document.write("<OPTION value=1 >"+share.staticip+"</OPTION>")
192.168.1.1 (line 613)
share is not defined
href="DDNS.htm"><script>Capture(share.ddns)</script></A>...
192.168.1.1 (line 543)
bmenu is not defined
href="StaRouter.htm"><script>Capture(bmenu.statu)</script></A>...
192.168.1.1 (line 531)
bmenu is not defined
href="Manage.htm"><script>Capture(bmenu.admin)</script></A>&nb...
192.168.1.1 (line 527)
bmenu is not defined
<script>Capture(bmenu.gaming)</script></A>   &n...
192.168.1.1 (line 523)
bmenu is not defined
href="Forward.htm"><script>Capture(bmenu.applications)</script...
192.168.1.1 (line 522)
bmenu is not defined
href="Filters.htm"><script>Capture(bmenu.accrestriction)</scri...
192.168.1.1 (line 518)
bmenu is not defined
href="Firewall.htm"><script>Capture(bmenu.security)</script></...
192.168.1.1 (line 514)
bmenu is not defined

These are JavaScript errors and no Java errors. Java has nothing to do with them. Updating Java won't make any difference.
Do you run any software firewall on the computer? As the problems occurs on IE and Firefox it could well be that your firewall damages the JavaScript in the web pages. Firewalls like to do that to protect your "privacy".

Trouble using the Web-based utility

I have a WRT54G wireless router, V8, firmware 8.0.0. It is Ethernet-connected to a Windows Vista machine running SP1.
I am having trouble using the Web-based utility. I can access it but cannot make any changes. For instance, if I change the settings on the Setup page and click "save", I get a "This webpage is not available"
I tried updating the firmware and got the same message. Disabling my personal firewall has no effect. Resetting the router from the button on its rear panel has no effect. I tried using with both Windows IE and Google Chrome browsers and got the same result.
I have been using this router without problem for months using a a Windows XP machine. This problem may be associated with my changing it to the current Windows Vista machine. I no longer have the Windows XP machine.
Please help me. Thank you and Happy New Year!
- tom

I spent a full day unsuccessfully trying to make it work, including numerous Linksys utilities downloaded from the site. I could not conjure any support on Linksys chat, and the live body on the Linksys tech support line wanted to charge me $29 for his help.
I finally succeeded by purchasing and installing a Netgear wireless router ($44, Staples) that came up flawlessly the first time. The Linksys device is in my trash.

Web based utility won't let me use automatic dhcp setup

Hi I use an mac osx with cable internet. i can plug in the wrt54g router correctly and the airport appears, but when I try to use the web-based utility it won't give me the option for automatic dhcp! Help me Dianne
Message Edited by dsowings on 12-25-2007 09:18 PM

are you talking about the options in the "internet connection type" on the router's web interface ??
if yes, then ensure that the firewall on the computer is disabled.
Revert with the results ...

Web-based utility will not load on new wet54g ethernet bridge

I just got a WET54g ethernet bridge to connect my bluray player to my existing network (wrt54gs router). I cannot get the setup cd to recognize the bridge connected to the laptop or the router. I thought that it would be no problem, just use web-based set-up. When attempting to access 192.168.1.226 I have to enter the password three times and then a blank page is loaded. Chat support ended up getting disconnected, so no luck there. Supposedly some of the steps chat wallked me through updated the firmware through ftp download, but I feel like nothing was done since you can't access the set-up page. Any suggestions are welcome. I'm running vista if that helps.

Start it from Scratch...Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your WET54G(ethernet bridge), wait for 30 seconds and re-connect the power cable...Now re-configure your WET54G(ethernet bridge)...Follow the link here to re-configure the WET54G(ethernet bridge)...Also under the configuration type select Static IP Address : For IP Address enter : 192.168.1.226, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 and save the settings...
After doing these you can unplug the Ethernet Bridge from the router and power cycle your router and the ethernet bridge both...Connect your ethernet bridge to your bluray player and test for active connection...

Lost ability to reach Web-based utility for WRT610N

Until recently (not sure exactly when), on my Windows XP system I used to be able to reach the Advanced Setup page for my WRT610N gateway router by pointing a browser to 192.168.1.1. No more: both Firefox and IE say "Waiting..." until they time out. Everything else seems to work fine; I can access the Internet and do whatever else I use the router for, no problem, I just can't reach that setup page. I updated the Linksys LELA utility the other day, but I don't think that would block the IP address from the browser. The lights on the front panel are OK, and Ping looks good:
>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
...and so forth...
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
I don't have a second computer, and factory reset is a last-ditch plan. Would like to diagnose the problem if possible; firmware, maybe? I did a firmware ugrade last November, but I'm sure I accessed the web setup since then.
This might be useful info; the router manual says that instead of entering the IP number, you can type in http://wrt160n.com to reach the setup page, but instead that address (and wrt610n.com) take me to external Web addresses, while 192.168.1.1 just hangs. I wonder what is the mechanism to trap the numerical and the alpha addresses and direct requests to the router advanced setup? That seems to be where the fault lies, I'm guessing.
Solved!
Go to Solution.

Are you trying to access the web utility from a wired and not a wireless computer? Wired is the best way to access, and sometimes is the only way by default.
You didn't mention whether you performed a soft reset of the router or not. That normally fixes the problem for me.
It might be worth it to borrow a laptop and wire it to the router to further narrow down the problem.

E1000 won't connect to Cisco Connect or the Web based set up

My router is working fine but I cannot connect to Cisco Connect or the web based advanced features now. I know I broke the cardinal rule by using advanced set up so that explains why Cisco connect won't work. But I can't figure out why I can't connect to the advanced web based utility now. Who made the decision to put some features in cisco connect but not include those features in advanced settings? And then if you use advanced settings cisco connect no longer works. This is such a turn off I'm actually thinking about returning the thing to Best Buy. That's like saying "if you open the hood of your car and touch anything parts of your car will no longer function". I call support and they repeat what they read on paper "reset the router and start over and don't use advanced settings". What a pain in the &^%$.

I've reinstalled the router again and just switched the ssid and password where it was before so all the devices in our home can connect. I first shut down the guest account using Cisco Connect (which is the only place you can control the guest account) and now I just use the advanced settings. So of course Cisco connect no longer works. I've got a strong signal all over our home. No disconnection issues at all. But this software design that puts some features in one part and other features in advanced and then shuts down cisco connect if you use advanced is insane. If I knew cisco was planning a firmware upgrade to give the advanced mode everything cisco connect has and more then I'd keep this thing. For the life of me I cannot understand why any software engineer would come up with such a design as this. And quite honestly I tried to play by their goofy rules of not using advanced settings and cisco connect died after about 4 uses. Never would connect again. Just said call support (in India) and after telling your life's story to someone simply being told to hit the reset button, power off and start the process all over again. If anyone at Cisco reads this stuff I think I have a legitimate complaint. Why on earth would you put features in Cisco Connect that aren't in advanced and why would you stop running Cisco connect just because I hard coded some mac addresses in advanced mode? I would love to know the logic behine such a crazy implementation of software.

Web based utitlity

Hi, my cousin just gave me his linksys BEFW11S4 wireless router which he hasnt used for a long tym. The problem is he cant remember the password for the web based utility, when i reset the router it lets me access the web based utility using the 'user' and 'admin' feature without any problem. However, i cant change any settings as whenever i do it asks me for a username and password again and i cant use the 'user' and 'admin' feature for some reason. Please if someone could help, it would be very helpful. thanks

thanks david but ive already resetted it a couple of times but with no avail, should i keep trying? And dill24 do you know where i can download the password cracking program from. it would be appreciated if you could provide a web link. what do i do once ive got this program?

No Web Based Access PAP2

I have a PAP2 connected to a WRT54GS.
I pick up phone, dial ****110# and write down the IP address provided.
Load up IE and type the same address into the address bar. IE can't connect to it (it bounces to my Google search page).
I log into the WRT54GS and check the DHCP Clients Table, and it identifies the PAP2 as having the address stated and entered above.
Am I missing something here?

The IVR 7932# feature is password protected by your Internet phone service provider. (The Web-based Utility is disabled by default because you will not need to use it unless instructed to do so by your service provider.) You may want to verify the password of your PAP2 from your Internet phone service provider.
Since the Web-based Utility is disabled by default, only your Internet phone service provider can unlock that and they’re the only one authorized to configure and Enable the Web Server.
For Factory Reset, pick up the phone attached to your Linksys, dial ****73738#, press 1 to confirm and then hang up the phone.
For PAP2 manual, refer to the link below:
http://www.net2phone.com/partnerships/distributors/product/broadband/pdf/n2plinksysinstallguide.pdf

WRT350N web based setup utility

I am attempting to run the web based router setup utility for a WRT350N. When attempting to log in the utility will not accept the default "leave user field empty and use the password admin". After 3 tries is goes to an unauthorized user diaglog box. Suggestions?.

Apparently someone has changed the router's password. If you are running an unsecured wireless network, and you left the password set to "admin", then perhaps your neighbor wirelessly connected to your router (accidently or intentionally) and changed your password. Likewise, anyone who has wired access to your router could have changed the password.
If you cannot remember the password, then you will need to reset the router to factory defaults, then setup the router again.
After you get your router setup and working, you should secure your wireless network using WPA2, or at least WPA encryption, and a strong password. Additionally, you should change your login password. You should not use "admin".
Message Edited by toomanydonuts on 10-31-2007 01:26 AM

WEB BASED MAPPING APPLICATION TO DEVELOP QUERY UTILITY USING MAPVIEWER

Dear Sir,
please any one can answer me as soon as possible its very urgent
WEB BASED MAPPING APPLICATION TO DEVELOP QUERY UTILITY USING MAPVIEWER
I     As oracle mapviewer Chapter 8 (Oracle Maps) says generating our own Web based mapping application we are trying to generate our own maps for our own data contains in our layers like example boundary lines and roads and etc. and we are following complete example as described in Oracle Mapviewer Document Chapter 8.
Before this step we tried with demo data downloaded from OTN mvdemo. And we downloaded latest demo today itself from the OTN and imported into our database schema called mvdemo. And we copied all three jar files mvclient and mvconnection and mvpalette into our jdeveloper .
II.     We created a jsp to execute the following code from oracle mapviewer chapter 8 documents
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"
"http://www.w3.org/TR/html4/loose.dtd">
<%@ page contentType="text/html;charset=windows-1252"%>
<%@ taglib uri="http://java.sun.com/jsf/html" prefix="h"%>
<%@ taglib uri="http://java.sun.com/jsf/core" prefix="f"%>
<%@ taglib uri="http://xmlns.oracle.com/adf/faces" prefix="af"%>
<%@ taglib uri="http://xmlns.oracle.com/adf/faces/customizable" prefix="cust"%>
<%@ taglib uri="http://xmlns.oracle.com/j2ee/jsp/tld/ojsp/jwcache.tld"
prefix="jwcache"%>
<%@ taglib uri="http://xmlns.oracle.com/adf/faces/html" prefix="afh"%>
<%@ taglib uri="http://xmlns.oracle.com/j2ee/jsp/tld/ojsp/fileaccess.tld"
prefix="fileaccess"%>
<%@ taglib uri="http://xmlns.oracle.com/j2ee/jsp/tld/ojsp/jesitaglib.tld"
prefix="JESI"%>
<f:view>
<html>
<head>
<META http-equiv="Content-Type" content="text/html" charset=UTF-8>
<TITLE>A sample Oracle Maps Application</TITLE>
<script language="Javascript" src="jslib/loadscript.js"></script>
<script language=javascript>
var themebasedfoi=null
function on_load_mapview()
var baseURL = " http://localhost:8888/mapviewer/omserver";
// Create an MVMapView instance to display the map
var mapview = new MVMapView(document.getElementById("map"), baseURL);
// Add a base map layer as background
mapview.addBaseMapLayer(new MVBaseMap("mvdemo.demo_map"));
// Add a theme-based FOI layer to display customers on the map
themebasedfoi = new MVThemeBasedFOI('themebasedfoi1','mvdemo.customers');
themebasedfoi.setBringToTopOnMouseOver(true);
mapview.addThemeBasedFOI(themebasedfoi);
// Set the initial map center and zoom level
mapview.setCenter(MVSdoGeometry.createPoint(-122.45,37.7706,8307));
mapview.setZoomLevel(4);
// Add a navigation panel on the right side of the map
mapview.addNavigationPanel('east');
// Add a scale bar
mapview.addScaleBar();
// Display the map.
mapview.display();
function setLayerVisible(checkBox){
// Show the theme-based FOI layer if the check box is checked and
// hide the theme-based FOI layer otherwise.
if(checkBox.checked)
themebasedfoi.setVisible(true) ;
else
themebasedfoi.setVisible(false);
</script>
</head>
<body onload= javascript:on_load_mapview() >
<h2> A sample Oracle Maps Application</h2>
<INPUT TYPE="checkbox" onclick="setLayerVisible(this)" checked/>Show customers
<div id="map" style="width: 600px; height: 500px"></div>
</body>
</html>
</f:view>

<%-- oracle-jdev-comment:auto-binding-backing-bean-name:backing_mapPage--%>
III.     When we run this jsp it’s giving us following Two errors
1     Error:     ‘MVMapView’ is undefined
     Code:     0
     URL:     http://192.168.100.149:8988/MapViewerApp-WebProj-context-root/faces/mapPage.jsp
2     Error:     ‘themebasedfoi’ is null or not an object
     Code:     0
     URL:     http://192.168.100.149:8988/MapViewerApp-WebProj-context-root/faces/mapPage.jsp
Please let us know what could be problem as soon as possible. Very urgent
Please let us know where we can find Mapviewer AJAX API’s for Jdeveloper Extention
Thanks
Kabeer

I currently use parameters, and they are passed from the form to the report. Report is then generated based on a function returning ‘strongly typed’ cursor. The ‘strongly typed’ cursor in my case returns a record consisting of an orderly collection of fields.
This collection of fields is returned by another function that relies on the IF … THEN logic.
However, the number of IF ... THEN statements is quite large (currently 64 covering all possible combinations of 6 parameters available in the form).
I would like to avoid the large number of IF … THEN statements, and hope that there is a way of passing a string to a query, where the Dynamic SQL would in Select close and Where close reflect parameters passed by the form.
In addition to this I would like to avoid creating and populating a table or a view dedicated to the report, because this may lead to a conflict in case of multiple users concurrently generating reports with different choice of parameters.
Edited by: user6883574 on May 28, 2009 9:16 PM

Modifying the web-based capture utility

Hello - we are looking to modify the web-based capture tool to only allow for video file uploads, and not capturing etc. Anyone have experience with this?
Thanks in advance!

not yet - but i would be interested in details..

Web Based Configuration possible security flaw

My coworkers and I found something quite interesting today...despite having configured FTP security settings (which have been confirmed to be set up and funcitoning. I can't open an FTP session to our remote target without specifying an admin user name and password) if you open the NI web based configuration tool in a browser, you can FTP to and from the target using the remote file browser without being logged in at all! Has anyone else experienced this??
CLA, LabVIEW Versions 2010-2013
Solved!
Go to Solution.

Apparently, these permissions are separate from FTP, but you can set these particular permissions on the Security configuration page of the web based configuration utility.
CLA, LabVIEW Versions 2010-2013

310N - web based utility password

Similar Messages

Maybe you are looking for