32'' LCD TV model 32FT2U firmware corrupted, help please!!
Hi All!!: Just recently my 32'' LCD TV model 32FT2U got corrupted firmware during an ac power blink, firmware updates are not posted at the support site, please, where can i get the original firmware, can anyone help me?
Thanks in advance!!
I'd suggest contacting customer support at (800) 631-3811.
- Peter
Similar Messages
-
Hello,
I have downloaded the latest version of BIOS firmware from Toshibas website. I checked it clearly with the model nr and serial nr. I went to the nordic site of bios update and downloaded the latest driver and BIOS.
My laptop is Satellite P200-1A2 and the serial nr is PSPB6E-02J023N5. From Toshibas website, I downloaded all the necessary drivers and bios. I started out with the installation of BIOS, when I tried to install it, then my pc froze. My power supply was on. The fan went all beserk and the screen was all frozen. I tried to let it work for 30 min, since I was afraid to interupt the installation. I couldn't wait more, so I turned the pc off by taking out the battery and power. When I then tried to turn on the laptop, nothing happens. All black screen.
Can anyone help? I did use the correct BIOS driver from Toshiba's own homepage, but apparently it didn't work. How can I restore the BIOS? I'm not sure what BIOS that I use. When I hold down Fn + B, and turn on the power, then all fans become crazy and DVD/HD ROM is also on.This must be Toshibas responsibility, since their own BIOS firmware crashed my pc. I don't want to spend money, I have already spend enought money for this old laptop alone. So I think it would be a pity, if I have had to pay for reparing my laptop.
I followed this procedure prescisely from : http://forums.mydigitallife.info/threads/870-Bios-Recovery-Procedures?p=26249#post26249
1. Use HP USB Disk Storage Format Tool with MiniDOS files to make your Bootable:USB Flash Drive (Flash Drive works in rear cases).
1: Worked perfect to make a USB flash drive, but what do you mean about Rear cases? You mean rare cases insted of rear? And I don't have a diskdrive, so how can I make an image file with boot, so I can add them on CD?
2. Copy all the files from Rescue to your: USB Stick
2one
3. Rename your BIOS file to bios.wph and copy it to your: USB Stick
3: I downloaded the same BIOS firmware and downloaded as EXE file, I extracted exe file and found a file called .ROM and I renamed the entire file into bios.wph
4. Remove the battery, unplug the computer from the power.
4: Done
5. Hold down: Fn+B and while holding plug the computer in to power (do not plug the battery) and pres the power button.
5: Done
6. Now you should hear the flopy drive working, hold the keys for a while and then let go.
6: I don't have a floppy drive but a HD/DVD/CD drive and that is working but with my USB flash drive, nothing happens
7. Leve the computer for at least 10 min. and if the computer does not restart it self turn the power down.
7: Nothing happens, I sense that it is not even reading the USB drive. So after 30 min, it still on and doing nothing
8. Plug the battery and the power sorce and if everything went OK the computer shold start normaly.
Note: This procedure is for Phoenix BIOS`es only and in some cases the USB Stick might not work.
8: Yes, the USB stick doesn't work, but how can I use create a bootable image file? And what are the steps for that? I don't have a floppy drive, most PC now a days doesn't use floppy drive. -
Time Capsule sparsebundle corruption help please
Hi
I went away for a week and when I came back I found that the Time Capsule was not backing up. Apparently, my family tells me there was a power outage during my absence and, therefore, this might be the cause of the problems.
I have a Time Capsule acting as our Time Machine drive which is accessed wirelessly from a MacBook.
Double clicking on the sparsebundle got me a message that 'Resource not available' and some searching of this forum makes me think the bundle is corrupted. I followed some advice to use the Terminal to force a mount of the bundle into Disk Utility and this is what appeared in the Terminal window:
<pre>
2010-03-28 23:58:21.207 hdiutil[474:c0b] Error loading /Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin: dlopen(/Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin, 262): no suitable image found. Did find:
/Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin: mach-o, but wrong architecture
2010-03-28 23:58:21.210 hdiutil[474:c0b] Cannot find function pointer VRPreviewCFPlugInFactory for factory 20D1C6B2-6A02-11D7-B5A6-000393D45566 in CFBundle/CFPlugIn 0x419ab0 </Library/Plug-ins/DiskImages/NUMPlugin.bundle> (bundle, not loaded)
2010-03-28 23:58:21.387 diskimages-helper[477:1603] Error loading /Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin: dlopen(/Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin, 262): no suitable image found. Did find:
/Library/Plug-ins/DiskImages/NUMPlugin.bundle/Contents/MacOS/NUMPlugin: mach-o, but wrong architecture
2010-03-28 23:58:21.388 diskimages-helper[477:1603] Cannot find function pointer VRPreviewCFPlugInFactory for factory 20D1C6B2-6A02-11D7-B5A6-000393D45566 in CFBundle/CFPlugIn 0x522d60 </Library/Plug-ins/DiskImages/NUMPlugin.bundle> (bundle, not loaded)
hdiutil: attach failed - Resource temporarily unavailable
</pre>
I am no Unix guru and I have no intention of using the Terminal except with explicit guidance as I really have no idea what I'm doing with it. As a result, I have no idea what the output means, but it doesn't look good. However I am generally technologically savvy.
As you may imagine, I would like to try to save the back ups contained in the bundle if at all possible before I hook up the laptop via ethernet to the TC and start everything again.
Right now, I have stopped further TM backups. I have already tried switching off TM, rebooting and then reselecting the TC but to no avail.
Any/all help will be so gratefully received.
Thanks in advance
GraemePlease don't post messages this way. They are difficult to read. For problems with Time Machine I would suggest
you start here: User Tips for Time Machine.
Note that if you cannot mount the sparsebundle in order to repair it using Disk Utility, then the sparsebundle is beyond
help. Erase the backup drive and start over. For a Time Capsule open Airport Utility, click on the Manual Update button.
Select Airport Utility Help from the Help menu and search for "erase." This will get you the help file on how to erase a
TC drive. -
H520s Windows 8 DVD-ROM disabled and error 19 - registry corrupt Help please!
Hi all and hoping for help with H520s, 64bit OS Windows 8. Error message showing problem with DVD-RAM Mat**bleep**a SW820; this is disabled in the device manager, and I can't use the DVD drive as a result. (yellow triangle)
Have tried windows fix utility on pc ; drivers are up to date. Have disabled, enabled etc. But it's still error 19
This was working perfectly until a couple of days ago when Microsoft ran a mega load of updates, including critical windows 8 updates. Am wondering if there's some conflict?
Have searched the Lenovo solution centre for up to date drivers for the dvd-RW but there aren't any. Don't really want to uninstall the DVD-ROM drive and attempt reinstall unless can definitely reinstall and can't find anything that reassures me I wil be able to do so.
Wondering if Is this similar to another issue on Toshiba pcs where it seems, according to various searches, it was a corrupted registry entry due to conflicts with pre installed pc rescue type utilities?
I'm no IT expert and the idea of registry fiddling is not reassuring.hi teapot,
Welcome to Lenovo Community Forums!
You can try Micorsoft's automated ix it tool about the same issue.
Check this Link
http://support.microsoft.com/kb/314060
try that and it should work,
Hope this helps,
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
Hello, I posted this in the optical forum but got no answers, so I hope someone could help here.
Hi there, I have just fitted an MSI CR52-M CDRW and ran live update to check for firmware. It said I had version 3.30 and 3.70 was available. I started the update procedure following exactly in windows mode and while it was updating it just simply crashed.
I used the flash recovery floppy it got me to create, but this just set me back to 3.30.
I tried again via live update, but this time chose to do it in dos mode. After going through the process and rebooting etc. It still says I have version 3.30?
Is there a problem with this firware upgrade or am I perhaps overlooking something?
I thank you in advance for any help and advice.Your post in the optical forum is the correct place. It may take a while to get a response.
-
Can't connect to internet after updating new Firmware wrt54g Help please!
So i just updated my firmware on my wrt54g ver 2 router, went through all the steps it updated successfully after that i hit the reset button and unplugged the router as tehe online instructions said to. Now i can't connect to the interent at all with either of my two wired computers or through the wireless. All the lights on the front of the router are on like the power, internet, and wireless connectivity. Also the the two WAN ports my computers are connected to in the router the lights are on and it's recognising them. But I can't connect to the internet or even see the router on my network settings. Somone suggested to reconfigure the router but when i go to set up new connection my computer doesn't detect the router and also i cant connect to the router using the ip address 192.168.1.1/ since there is no internet connection. Is there a way to get to the router options or a way to revert it to its old firmware. Any help would be much appreciated. I should after updating the firmare the power button is contantly blinking.
I am having the exact same problem.. I have the same router and same version as well.. I followed the directions and upgraded the firmware. it said update successfull and then I reset it and power cycled it to find that my network no longer works and I cannot access the router..I've looked through all the troubleshooting guides and they do not help.. It says if you can't access the web based page then to use the TFTP utility to re-flash the router’s firmware but it seems it cannot make a connection to the router.. I've tried to ping it like it says to in the TFTP guide but it does not seem to be able to make a connection to the router.. I tried to access Management Mode to recover the router and resume the loading of the firmware upgrade but I can't get the Management Mode Firmware Upgrade page to open as well.. So what gives? I followed the directions but the only thing I seemed to accomplish was to brick my router.. Does anyone have a clue on how to go about fixing this problem? Any help is appreciated..
-
Well... I bought my mini in July. It was working fine until the other day when I connected it to the computer to update the songs. It suddenly had the folder and sad ipod error. I tried to restore it and it had the error, "Firmware error, cannot write to disk." I tried putting it in Disk Mode, it worked but I still can't update it. I can't start it either, I'm not sure if I should send it in or not.
Apparently, it sounds like there's a problem with your iPod's hard disk; honestly, I don't think there's anything at home you can do about it.
Send it in. -
1616 screen goes black - Help please
I have just bought a new Nokia 1616. I have worked through all the settings but cannot find the one to stop it turning the screen off after a few minutes of non-use. The screen goes black and so you don't know if it is switched on or not. Ideally I would like it to show the clock like my previous model 1600 did. Help please.
If you press on the red phone button the time will display on the screen if the phone is on. It will also show you if the phone is locked or not by showing a small key. Press the menu button and the * key as usual to unlock.
-
Hp laserjet 1536dnf MFP LCD panel displays "firmware corrupt ready 2 download"
Hi guys
Am new in the forums but i beleive somebody somewhere has a solution for the following: a client tried updating the firmware for the above printer but ended up with the message, "Firmware corrupt Ready 2 download". Is there any combinations of buttons to press to do a cold reset?
Mst2015Hi @Mst2015 ,
I see by your post that after doing a firmware update on the printer, the printer displays "firmware corrupt ready 2 download". I would really like to be able to help you resolve this issue.
Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation.
I can send you that information in a private message.
In the forum beside your handle name just click on the envelope to view it.
You should always do the firmware update by a USB connection.
Please let me know if you require any additional assistance.
Have a fantastic day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP -
itunes showing 'backup is corrupt or not compatible with the firmware you restored'.Please help.
Hi Ckuan,
Thanks a lot for your advice.
Deleting the correupted back up means to delete the information of one month since the last back up I made is one month ago.....right?
This back up I made right before I restored my iphone. During the restore however my OS was upgraded to 5.1.1. and reading the comments on the internet it seems I am not the only one whom experience this problem.
Can it be that if I downgrade my OS back to 5.1. the back up will not be considered as corrupted? If so, how do I downgrade the iphone?
Thanks in advance. -
Firmware corrupt ready 2 download Fatal Error 7
Hello Guys,
the issue is with the Laserjet 1536dnf MFP I can't recover it at all it's stuck in Firmware corrupt ready 2 download
I have done step by step whatever was here :
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03109721
I can see the display on printer which is showing downloading but after download complete it gives error FATAL ERROR 7
CALL SUPPORT
meaning I was not able to upgrade the corrupted firmware at all .
please tell me what to do to solve this ?
Forgot to mention still my printer has warranty HP experts please help me
Thanks
AbdullahHi @Ayoubi,
Welcome to the HP Forums!
I understand that your HP Laserjet 1536dnf MFP can't be recovered at all that it is stuck in Firmware corrupt ready to download. I am sorry to hear this but happy to help!
Please try a hard reset, to do so, please see this post, How to perform a Hard Reset, by @Rich1. It is important that the printer's power cable is plugged directly into the wall outlet, and not a surge protector. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector. This applies to Inkjet printers as well.
Afterwards, try the firmware update again. If the issue is still not resolved, please call our phone support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. Country-language selector.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping! -
Solaris 5.9 - Determine HBA model/driver/firmware information
Hi,
I've been given a couple of Solaris 5.9 servers and asked to determine the make, model, firmware and driver of HBA that is installed.
After doing some research on the net, I found commands such as 'luxadm'/'cfgadm' etc, yet cannot extract the necessary information.
Can anyone advise on the basic commands that could help me?
Thanks in advance
MikeI'm still struggling to get the brand, model and firmware of HBAs from the servers.
Can you give any further advice please?
I've managed to extract very basic information such as brand and model from v5.10 servers using 'fcinfo hba-port', but not the firmware revision.
Thanks,
Mike -
LaserJet Pro M1536dnf Multifunction Printers - A 'Firmware Corrupt Ready 2 Download'
LaserJet Pro M1536dnf Multifunction Printers - A 'Firmware Corrupt Ready 2 Download'
I run firmware files named that M1530_Series_FW_Update-20120629 file from network in Win.7 Then Firmware Corrupt Ready 2 Download is appeared. All operation blocked, pls help?How was the printer connected to the computer? USB or networked?
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
Hi can anybody help please. I am having terrible problems trying to use my Nikon D7100 to tether. I have downloaded the latest Lightroom updates and also checked my firmware which is also the latest avaiable and still Lightroom wont detect my camera!. When I use a friends Canon camera it works every time!
Hi Keith thanks for your reply I have Lightroom 5.7.1 64 bit and my Nikon's firmware is version 1.02
-
I have an IPOD Nano 4th Generation 8GB and am unable to restore it back to factory settings even when it is connected to my MAC. I have tried the menu/select hold but is not doing anything. When connected to the MAC and select restore in itunes it comes up with 'Firmware Corrupt'. It also states the IPOD is up to date. I have the latest operating system on my MAC and wonder if this may be part of the issue?
Can anyone shed light as to what i can do to reset it back to factory settings as would like to sell it and ensure it is ready for the new owner.
Thanks
jay68gSee here: What to do if iPod can't be updated because the firmware file was corrupt or not found
B-rock
Maybe you are looking for
-
How to keep some things in iTunes from being uploaded to iTunes Match
There are files that end up in my iTunes library, because they are mp3's I believe, that aren't music and I don't want uploaded to iTunes Match. For example, my UVerse phone messages are downloaded as mp3's and end up in my iTunes Library. How can I
-
HT2534 How can I register to AppStore without a credit card? (iOS6) :((
Please help me.
-
Hello!Yesterday I have updated my phone software from V11 to v12.When the phone automatically restarted the phone came up with the message:Update completed but the next message was "No connection avaiable".At to moment the WLAN fuction has completely
-
Hello, I have been practicing backup and recovery. How can I recover my database after loss of all online redolog files while the database was open. Oracle version:-10.2.0.1 OS:- Win(32 bit) Database is in archive log mode. Have taken user managed ho
-
It does not matter what or where the .pdf is, so it is not a result of a particular website, rather it is a fault in Firefox. It just started in the last week.