3545 MCU is not getting up

Hello
I am using Cisco 3545 MCU , but it is showing wakeup configuration mode after getting disconnected while upgrading the software. please help me out
Regards
Subhasis

Hi,
My cloning is completed successfully but my apps listener is not getting up?? What is
the problem ?Please run AutoConfig and make sure it completes successfully. Also,make sure your FND_NODES table have correct entries -- Steps To Clean Nonexistent Nodes Or IP Addresses From FND_NODES [ID 260887.1]
What is the error you get? Do you have all the services up and running?
Please post the complete error message along with any error messages from listener log file.
Thanks,
Hussein

Similar Messages

Cisco 3545 MCU/EMP

Hello all,
I'm deploying a videoconference solution with a Cisco 3545 with one MCU and one EMP. I've done the basic configurations. The MCU has the ip 10.10.0.170 and the EMP with the 10.10.0.171, mask 255.255.255.240. The problem is that the EMP card never appears in the Media Processing tab in the MCU of the MCU admin page, and on the EMP console keeps popping up the message "NO MCU detected at this IP address: 10.10.0.170".
Do you have any idea?
Best regards.

I was just troubleshooting a video issue recently, and although our problems were different, I learned a few troubleshooting tools.
1. Go on your MCU and see if you can schedule Video meetings directly on the MCU, just to see if that piece works.
2. If that is working, go on your Video Admin web interface and go under Admin/Resource Management...click the MCU tab and then click on the link to the MCU. There is an Update button down there. Click the Update button, then try again.
What I have discovered is if that at any point your restart your MCU and don't click that Update button after, the Video Admin will get out of sync with the MCU and not be able to schedule Video.
So that is something to try to start with.

Total is not getting displayed in the ALV output.

Hi,
Total is not getting displayed in the ALV output.
I m using :REUSE_ALV_BLOCK_LIST_APPEND & REUSE_ALV_BLOCK_LIST_DISPLAY
Are there any issues with it as the same settings are working fine with REUSE_ALV_LIST_DISPLAY
source code:
DATA: layout TYPE slis_layout_alv,
      IT_eventS TYPE slis_t_event,
      fcat   TYPE slis_t_fieldcat_alv WITH HEADER LINE,
      rec_fcat TYPE slis_t_fieldcat_alv WITH HEADER LINE.
TYPES: BEGIN OF ty_tab,
      belnr TYPE dberchz-belnr,
      belzart TYPE dberchz-belzart,
      net TYPE dberchz-nettobtr,
      END OF ty_tab.
DATA: lt_tab TYPE STANDARD TABLE OF ty_tab.
SELECT belnr belzart nettobtr
FROM dberchz
INTO TABLE lt_tab[]
WHERE belnr eq '000000000001'.
if sy-subrc ne 0.
ENDIF.
* defining layout
layout-colwidth_optimize = 'X'.
layout-def_status = 'X'.
*defning event
*event
*defining field catalog
fcat-col_pos = 1.
fcat-fieldname = 'BELNR'.
fcat-tabname = 'LT_TAB'.
APPEND fcat.
fcat-col_pos = 2.
fcat-fieldname = 'BELZART'.
fcat-tabname = 'LT_TAB'.
APPEND fcat.
fcat-col_pos = 3.
fcat-fieldname = 'NET'.
fcat-tabname = 'LT_TAB'.
fcat-do_sum = 'X'.
APPEND fcat.
*calling alv
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_INIT'
EXPORTING
    i_callback_program             = 'YZ_PLR'
*   I_CALLBACK_PF_STATUS_SET       = ' '
*   I_CALLBACK_USER_COMMAND        = ' '
*   IT_EXCLUDING                   =
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_APPEND'
EXPORTING
    is_layout                        = layout
    it_fieldcat                      = fcat[]
    i_tabname                        = 'LT_TAB'
    it_events                        = IT_EVENTS[]
*   IT_SORT                          =
*   I_TEXT                           = ' '
tables
    t_outtab                         = lt_tab[]
* EXCEPTIONS
*   PROGRAM_ERROR                    = 1
*   MAXIMUM_OF_APPENDS_REACHED       = 2
*   OTHERS                           = 3
IF sy-subrc <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*         WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_DISPLAY'
Thanks,
Gaurav

Hi
No I don't think, this is my code (based on your code) and it works fine:
TYPE-POOLS SLIS.
DATA: BEGIN OF LT_TAB OCCURS 0,
       BELNR LIKE BSEG-BELNR,
       GJAHR LIKE BSEG-GJAHR,
       WRBTR LIKE BSEG-WRBTR,
       WAERS LIKE BKPF-WAERS,
      END OF LT_TAB.
DATA: LAYOUT     TYPE SLIS_LAYOUT_ALV,
      IT_EVENTS TYPE SLIS_T_EVENT,
      FCAT       TYPE SLIS_T_FIELDCAT_ALV WITH HEADER LINE,
      REC_FCAT   TYPE SLIS_T_FIELDCAT_ALV WITH HEADER LINE.
START-OF-SELECTION.
FCAT-COL_POS       = 1.
FCAT-FIELDNAME     = 'BELNR'.
FCAT-TABNAME       = 'LT_TAB'.
FCAT-REF_FIELDNAME = 'BELNR'.
FCAT-REF_TABNAME   = 'BSEG'.
APPEND FCAT.
FCAT-COL_POS       = 2.
FCAT-FIELDNAME     = 'GJAHR'.
FCAT-TABNAME       = 'LT_TAB'.
FCAT-REF_FIELDNAME = 'GJAHR'.
FCAT-REF_TABNAME   = 'BSEG'.
APPEND FCAT.
FCAT-COL_POS       = 3.
FCAT-FIELDNAME     = 'WRBTR'.
FCAT-TABNAME       = 'LT_TAB'.
FCAT-CFIELDNAME    = 'WAERS'.
FCAT-REF_FIELDNAME = 'WRBTR'.
FCAT-REF_TABNAME   = 'BSEG'.
FCAT-DO_SUM        = 'X'.
APPEND FCAT.
FCAT-COL_POS       = 4.
FCAT-FIELDNAME     = 'WAERS'.
FCAT-TABNAME       = 'LT_TAB'.
FCAT-REF_FIELDNAME = 'WAERS'.
FCAT-REF_TABNAME   = 'BKPF'.
FCAT-DO_SUM        = SPACE.
APPEND FCAT.
SELECT * FROM BSEG INTO CORRESPONDING FIELDS OF TABLE LT_TAB
    WHERE BUKRS = 'MAAB'
      AND BELNR = '0000000001'.
LT_TAB-WAERS = 'EUR'.
MODIFY LT_TAB FROM LT_TAB TRANSPORTING WAERS WHERE WAERS = SPACE.
*CALLING ALV
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_INIT'
    EXPORTING
      I_CALLBACK_PROGRAM = 'ZPROVAMAX5'.
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_APPEND'
    EXPORTING
      IS_LAYOUT   = LAYOUT
      IT_FIELDCAT = FCAT[]
      I_TABNAME   = 'LT_TAB'
      IT_EVENTS   = IT_EVENTS[]
    TABLES
      T_OUTTAB    = LT_TAB[].
CALL FUNCTION 'REUSE_ALV_BLOCK_LIST_DISPLAY'.
I've also inserted a currency field
Max

Master data is not getting displayed in the Report in Quality

HI Experts,
I have ZESP_Num as master for my transaction data.
I have loaded the data in the Development and designed and checked my report. It is working fine.
But after moving it to Quality. My report is not getting the master data.
When I try to do right click manage ZESP_Num.
I'm getting message like this.
The data from the InfoProvider ZESP_NUM involved could not be checked
Message no. DBMAN242
Diagnosis
A participating InfoProvider is virtual and aggreement between results and selections cannot be guaranteed.
Can anyone plz help me.
Thanks

Hi,
Please check the SNOTE Note 1364083 u2013 Message text will appear unexpectedly in surface.
Hope helpful.
Regards,
RAO

Data is not getting displayed in the report from an Infoset.

Hi All,
I am having a report based on an infoset. This report is displaying the data in the Dev. envmt. When it is transported to the QA, it is not displaying the data in the BEx as well as RSRT, in the QA envmt. The patch levels of both the Dev. and QA are the same. The Queries are same in the Dev and QA also.
While trying to display the data from the infoset (rt.click- display data), i am able to view the data, in the QA.
Could anyone please suggest why the data is not getting displayed in the query designer.
Thanks & Regards,
A.V.N.Rao

Hi Ashish,
I ran the "ZPS/!ZPS" in RSRT where ZPS is the infoset name. In Dev, it displayed the values. In QA, it displayed the below messages:
ECharacteristic 0TCAKYFNM does not exist. Check authorizations
WThere are calculated elements. These results are bracketed [ ]
and below that, it displayed the values for Number of records. But, it has not displayed the values for the other figures.
Does this has any impact in QA.
Thanks & Regards,
AVN Rao.

'@' not getting displayed in the ALV report

Hello,
I am facing a strange issue in the ALV report display. A string starting with '@' is not getting displayed and says "default icon " on the report. and this is varying from system to system for the same user.
can anyone please help me in resolving the issue.
Thanks in advance.
Thanks and Regards,
Santhosh Guptha N.

@ is a default value as per ALV internal process. This is used in icons .
I think this is causing the confusion.
Check in the fieldcat if there is any adjsutment to be made to handle this.
Br,
Vijay

Dynamic mandatory field error message is not getting displayed in webui

Hi,
In Appointment if the importance is HIGH i made Location as mandatory.For this i enhanced BT126H_APPT/ApptDetails. In the get_p_location() method of BTACTIVITYYH i have written the code.
Now the problem is Error message for this dynamic mandatory field is not getting displayed in webui.
I debugged in DO_FINISH_INPUT error message is getting generated but it is not getting displayed in ui.
Can anybody tell where the problem is?
Thanks,
Hari.

Hi Hari,
Really sorry do not know how to convert this nug file to text
How ever quick solution for your problem would be just keep your validation in 'DO_VALIDATE_INPUT' method of the view controller.
Means even if the User clicks on SAVE , Since it fails here , it would not allow you to go further.
Thanks,
Rajesh P

Time From field is not getting displayed in correct format in Activities

Hello Experts ,
We are facing one problem in UI , when we search for Activities in Web UI . In the field "Time From" we are not getting the time in correct format , ie is instead of getting time as say 13::38 we are getting time as 13::3 , but when we place cursor on it the field it shows correct format say 13::38.
Can any one suggest how to display in correct format ?
Regards
Vinayak

Hi,
Its an SAP Product error.
Please check note 1151821 ,if you facing the greyed button in time.Also the other note 1136402 needs to be applied for time display issue
- Bobby

Portal Forms are not getting displayed in the new oracle environment.

Hi All,
The Forms in our Portal applications are not getting displayed after we have done the upgradation of Database in Unix from 8i to 9i. The reports are working fine.The forms that were added as portlets are not getting displayed and other forms that are called thorough links returns error when it is run. The Newly created forms are also not running but returns error. The Portal Version is 3.0.9.8.3. Pls help.
Regards,
Tom

Hi ,
Based on the requirement , check whether the customer contact has been done carried out for the invoice , then possibility it must have gone out of the worklist , chekc whether the Invoice posted in the AR has been transferred to FSCM collection .

Battery , time , signal strength bar is not getting displayed in home screen , these will be displayed only when i click on any app. Can u let me know the setting change ?

Battery , time , signal strength bar is not getting displayed in home screen , these will be displayed only when i click on any app. Can u let me know the setting change ?

Did you check the Zoom setting?
Have you tried a reset (reboot)? Hold HOME and SLEEP until an Apple logo appears.
If it isn't Zoom and a reboot doesn't help try Settings/General/Reset - Reset all settings

Header information not getting displayed in the lines

Hello Everyone
I have a very basic question - its very simple but not working for me with so many attempts
My XML structure looks like this . In the RTF , I have header information and then a table for line information looping through G_LINES.
IN this lines table I need the SHIP_CUSTOMER_ID of the header to be displayed. I have tried all options like <?../SHIP_CUSTOMER_ID?> or <?../G_ORDERS/SHIP_CUSTOMER_ID?> , however nothing seems to be working and I am not getting the field to be displayed. Can someone please help?
XML structure is as follows:
<XXSTOL_29251_PICK_TKT>
<LIST_G_ORDERS>
<G_ORDERS>
<CUSTOMER_NUMBER>1411</CUSTOMER_NUMBER>
<SHIPPING_INSTRUCTIONS1></SHIPPING_INSTRUCTIONS1>
<SHIP_CUSTOMER_ID>256</SHIP_CUSTOMER_ID>
<G_LINES>
</G_LINES>
<G_LINES>
</G_LINES>
</G_ORDERS
</LIST_G_ORDERS>
</XXSTOL_29251_PICK_TKT>

Are you grouping within G_LINES? If so, use ../../SHIP_CUSTOMER_ID
or send me the xml and RTF template to [email protected] so that I can get a better look at the data structure and try to help.
Thanks,
Bipuser

Default Value is not getting displayed in SUN ONE Ldap

Hello,
I have created an attribute in slapd.user_at.conf and it is associated in slapd.user_oc.conf.
The attribute default value is given through SUN ONE Console. But, In our application the default value is not getting displayed.
We need the default value to run our applicatin. Can anyone help me for this issue
Regards,
K. Senthil Kumar

Hi anandkumar,
I belive this issue can be resolved by changing the Query proprties for the perticular field.
Kindly check the Field proerties in query designer and ensure that Text is enabled ather than Key.
__Field property check up:__Go to query designer->click onn the field-> Right hand side in properties click on display tab-> select Text in drop down menu of Display as tab.
FURTHER CHECK UP: check the master data avaiulability for the perticular info object, if masterdata is not available, do the text data for txt data availability in report level.
Hope this helps you!!
Best Regards,
Maruthi

Material type not getting displayed in the cube........

Hi,
In my infocube material type for one of the material is not getting displayed.
When I check in the content of the cube for this material all the fileds are getting displayed except material type.
However it is present in the material master data from which it is put into the update rules to populate in the cube.
Its getting displayed for some other materials , so we cant say that mapping is wrong or problem with update rules.
Can some body let me know what could be the reason.
Thanks,
Jeetu

Hi Jeetu,
can you check in your cube if you have for one material, entries with AND entries without the MATL_TYPE? If this is the case then you were loading transactional data before having the corresponding material master data.
You should adapt your scenario:
- first do not use the standard attribute derivation during your URules: performance is very bad.
- implement a start routine filling an internal table with your material and MATL_TYPE for all entries of material in your datapackage.
- implement an update routine on the MATL_TYPE with a READ on this internal table an raise an ABORT = 4 if the MATL_TYPE is initial or the material in not found.
Now to fix your situation you'll have to reload your cube or alternatively just reload your missing MATL_TYPE MATERIAL from your cube itself and selective delete those which are empty.
hope this helps...
Olivier.

Barcode C128 is not getting displayed in Sapscript

HI,
I need to print the barcode in the Sapscript.
The barcode is not getting displayed even in the preview also, when I give the Barcode C128.
But when I give other Barcodes, it is getting displayed in the preview.
Can anyone let me know the solution to print the barcode for C128, as others are not that much fit to print.
Thanks
Rakesh

Hi Dieter,
No. I haven't.
Is this the reason for that?
let me know the procedure.
thanks
Rakesh

PIR & CIR is not getting displayed in APO product master

Hi guys,
I have created PIR and CIR in R/3 ,but it is not getting displayed in APO . Please guide me to resolving this what are the settings i have to check in the SAP system.
Thanks
S.Murali

I am Basis consultant.
Regarding RFC, logical system assinement, are the things are configured.
But still it is not active the integration between R/3 & APO server.
(Behalf of Murali )

3545 MCU is not getting up

Similar Messages

Maybe you are looking for